AMICC A29L320A

A29L320A Series
4M X 8 Bit / 2M X 16 Bit CMOS 3.0 Volt-only,
Boot Sector Flash Memory
Document Title
4M X 8 Bit / 2M X 16 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
Revision History
Rev. No.
History
Issue Date
Remark
0.0
Initial issue
April 12, 2006
Preliminary
0.1
Error correction: Top/Bottom device ID code and pin configurations
May 25, 2006
0.2
Change Table1 & Program/Erasure time
July 3, 2006
1.0
Final version release
January 5, 2007
1.1
Modify symbol “L” outline dimensions in TSOP 48L package
November 15, 2007
(November, 2007, Version 1.1)
Final
AMIC Technology, Corp.
A29L320A Series
4M X 8 Bit / 2M X 16 Bit CMOS 3.0 Volt-only,
Boot Sector Flash Memory
Features
„ Single power supply operation
- Regulated voltage range: 2.7 to 3.6 volt read and write
operations for compatibility with high performance 3 volt
microprocessors
„ Access times:
- 70/80/90/120 (max.)
„ Current:
- 2mA active read current at 1MHz
- 10mA active read current at 5MHz
- 20 mA typical program/erase current
- 500 nA typical CMOS standby or Automatic Sleep Mode
current
„ Flexible sector architecture
- Eight 8 Kbyte sectors
- Sixty-three 64 kbyte sectors
- Any combination of sectors can be erased
- Supports full chip erase
- Sector protection:
„ Unlock Bypass Program Command
- Reduces overall programming time when issuing
multiple program command sequence
„ Top or bottom boot block configurations available
„ Embedded Algorithms
- Embedded Erase algorithm will automatically erase the
entire chip or any combination of designated sectors and
verify the erased sectors
- Embedded Program algorithm automatically writes and
verifies data at specified addresses
„ Typical 100,000 program/erase cycles per sector
„ 20-year data retention at 125°C
- Reliable operation for the life of the system
„ CFI (Common Flash Interface) compliant
- Provides device-specific information to the system,
allowing host software to easily reconfigure for different
Flash devices
„ Compatible with JEDEC-standards
- Pinout and software compatible with single-power-supply
Flash memory standard
- Superior inadvertent write protection
„ Data Polling and toggle bits
- Provides a software method of detecting completion of
program or erase operations
„ Ready / BUSY pin (RY / BY )
- Provides a hardware method of detecting completion of
program or erase operations
„ Erase Suspend/Erase Resume
- Suspends a sector erase operation to read data from, or
program data to, a non-erasing sector, then resumes the
erase operation
„ Hardware reset pin ( RESET )
- Hardware method to reset the device to reading array
data
„ WP /ACC input pin
- Write protect ( WP ) function allows protection of two
outermost boot sectors, regardless of sector protect
status
- Acceleration (ACC) function provides accelerated
program times
„ Hardware/Software temporary sector block unprotect
command allows code changes in previously locked
sectors
„ Hardware/Software sector protect/unprotect command
„ Package options
- 48-pin TSOP (I) or 48-ball TFBGA
- All Pb-free (Lead-free) products are RoHS compliant
General Description
Suspend mode. The standard A29L320A offers access times
of 70,80,90 and 120ns, allowing high-speed microprocessors
to operate without wait states. To eliminate bus contention
the device has separate chip enable ( CE ), write enable
The A29L320A is a 32Mbit, 3.3 volt-only Flash memory
organized as 2,097,152 words of 16 bits or 4,194,304 bytes
of 8 bits each. The 8 bits of data appear on I/O0 - I/O7; the 16
bits of data appear on I/O0~I/O15. The A29L320A is offered in
48-ball TFBGA and 48-Pin TSOP packages. This device is
designed to be programmed in-system with the standard
system 3.3 volt VCC supply. Additional 12.0 volt VPP is not
required for in-system write or erase operations. However,
the A29L320A can also be programmed in standard EPROM
programmers.
The A29L320A has the first toggle bit, I/O6, which indicates
whether an Embedded Program or Erase is in progress, or it
is in the Erase Suspend. Besides the I/O6 toggle bit, the
A29L320A has a second toggle bit, I/O2, to indicate whether
the addressed sector is being selected for erase. The
A29L320A also offers the ability to program in the Erase
(November, 2007, Version 1.1)
( WE ) and output enable ( OE ) controls.
The device requires only a single 3.3 volt power supply for
both read and write functions. Internally generated and
regulated voltages are provided for the program and erase
operations.
The A29L320A is entirely software command set compatible
with the JEDEC single-power-supply Flash standard.
Commands are written to the command register using
standard microprocessor write timings. Register contents
serve as input to an internal state-machine that controls the
erase and programming circuitry. Write cycles also internally
latch addresses and data needed for the programming and
1
AMIC Technology, Corp.
A29L320A Series
contents of other sectors. The A29L320A is fully erased
when shipped from the factory.
The hardware sector protection feature disables operations
for both program and erase in any combination of the
sectors of memory. This can be achieved via programming
equipment.
The Erase Suspend/Erase Resume feature enables the user
to put erase on hold for any period of time to read data from,
or program data to, any other sector that is not selected for
erasure. True background erase can thus be achieved.
The hardware RESET pin terminates any operation in
progress and resets the internal state machine to reading
array data. The RESET pin may be tied to the system reset
circuitry. A system reset would thus also reset the device,
enabling the system microprocessor to read the boot-up
firmware from the Flash memory.
The device offers two power-saving features. When
addresses have been stable for a specified amount of time,
the device enters the automatic sleep mode. The system can
also place the device into the standby mode. Power
consumption is greatly reduced in both these modes.
erase operations. Reading data out of the device is similar to
reading from other Flash or EPROM devices.
Device programming occurs by writing the proper program
command sequence. This initiates the Embedded Program
algorithm - an internal algorithm that automatically times the
program pulse widths and verifies proper program margin.
Device erasure occurs by executing the proper erase
command sequence. This initiates the Embedded Erase
algorithm - an internal algorithm that automatically
preprograms the array (if it is not already programmed)
before executing the erase operation. During erase, the
device automatically times the erase pulse widths and
verifies proper erase margin. The Unlock Bypass mode
facilitates faster programming times by requiring only two
write cycles to program data instead of four.
The host system can detect whether a program or erase
operation is complete by observing the RY / BY pin, or by
reading the I/O7 ( Data Polling) and I/O6 (toggle) status bits.
After a program or erase cycle has been completed, the
device is ready to read array data or accept another
command.
The sector erase architecture allows memory sectors to be
erased and reprogrammed without affecting the data
Pin Configurations
„ TSOP (I)
A15
A14
A13
A12
A11
A10
A9
A8
A19
A20
WE
RESET
NC
WP/ACC
RY/BY
A18
A17
A7
A6
A5
A4
A3
A2
A1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
(November, 2007, Version 1.1)
A29L320AV
2
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
A16
BYTE
VSS
I/O 15(A-1)
I/O7
I/O14
I/O6
I/O 13
I/O5
I/O 12
I/O4
VCC
I/O 11
I/O3
I/O 10
I/O2
I/O9
I/O1
I/O8
I/O0
OE
VSS
CE
A0
AMIC Technology, Corp.
A29L320A Series
Pin Configurations (continued)
„ TFBGA
TFBGA
Top View, Balls Facing Down
A6
B6
C6
D6
E6
F6
A13
A12
A14
A15
A16
BYTE
A5
B5
C5
D5
E5
F5
G5
A9
A8
A10
A11
I/O7
I/O14
I/O13
A4
B4
C4
D4
E4
F4
G4
H4
WE
RESET
NC
A19
I/O5
I/O12
VCC
I/O4
A3
B3
C3
D3
E3
F3
G3
H3
WP/ACC
A18
A20
I/O 2
I/O10
I/O11
I/O3
A2
B2
C2
D2
E2
F2
G2
H2
A7
A17
A6
A5
I/O0
I/O 8
I/O9
I/O1
A1
B1
C1
E1
F1
G1
H1
A3
A4
A2
A0
CE
OE
VSS
RY/BY
(November, 2007, Version 1.1)
D1
A1
3
H6
G6
I/O15(A-1)
VSS
H5
I/O6
AMIC Technology, Corp.
A29L320A Series
Block Diagram
RY/BY
I/O0 - I/O15 (A-1)
VCC
VSS
Sector Switches
RESET
WE
Input/Output
Buffers
Erase Voltage
Generator
State
Control
BYTE
WP/ACC
PGM Voltage
Generator
Command
Register
Chip Enable
Output Enable
Logic
CE
OE
VCC Detector
Timer
A0-A20
Data Latch
Y-Decoder
Y-Gating
X-decoder
Cell Matrix
Address Latch
STB
STB
Pin Descriptions
Pin No.
A0 – A20
Address Inputs
I/O0 - I/O14
Data Inputs/Outputs
I/O15 (A-1)
I/O15
Data Input/Output, Word Mode
A-1
LSB Address Input, Byte Mode
CE
Chip Enable
WE
Write Enable
OE
Output Enable
RESET
Hardware Reset
BYTE
Selects Byte Mode or Word Mode
RY/ BY
Ready/ BUSY - Output
VSS
Ground
VCC
Power Supply
NC
WP /ACC
(November, 2007, Version 1.1)
Description
Pin not connected internally
Hardware Write Protect / Acceleration Pin
4
AMIC Technology, Corp.
A29L320A Series
Absolute Maximum Ratings*
*Comments
Storage Temperature Plastic Packages. . . -65°C to + 150°C
Ambient Temperature with Power Applied. -55°C to + 125°C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +4.0V
A9, OE & RESET (Note 2) . . . . . . . . . . . . . -0.5V to +10.5V
WP /ACC . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +10.5V
All other pins (Note 1) . . . . . . . . . . . . . . -0.5V to VCC + 0.5V
Output Short Circuit Current (Note 3) . . . . . . . . . . . . . 200mA
Stresses above those listed under "Absolute Maximum
Ratings" may cause permanent damage to this device.
These are stress ratings only. Functional operation of
this device at these or any other conditions above
those indicated in the operational sections of these
specification is not implied or intended. Exposure to
the absolute maximum rating conditions for extended periods
may affect device reliability.
Operating Ranges
Notes:
Commercial (C) Devices
1. Minimum DC voltage on input or I/O pins is -0.5V. During
voltage transitions, input or I/O pins may undershoot VSS
to -2.0V for periods of up to 20ns. Maximum DC voltage
on input and I/O pins is VCC +0.5V. During voltage
transitions, input or I/O pins may overshoot to VCC +2.0V
for periods up to 20ns.
2. Minimum DC input voltage on A9, OE and RESET is -
Ambient Temperature (TA) . . . . . . . . . . . . . . . . 0°C to +70°C
Extended Range Devices
Ambient Temperature (TA)
For –U series . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
For –I series . . . . . . . . . . . . . . . . . . . . . . . . . -25°C to +85°C
0.5V. During voltage transitions, A9, OE and RESET
may overshoot VSS to -2.0V for periods of up to 20ns.
Maximum DC input voltage on A9 is +10.5V which may
overshoot to 14.0V for periods up to 20ns.
3. No more than one output is shorted at a time. Duration of
the short circuit should not be greater than one second.
VCC Supply Voltages
VCC for all devices . . . . . . . . . . . . . . . . . . . . +2.7V to +3.6V
Operating ranges define those limits between which the
functionally of the device is guaranteed.
command. The contents of the register serve as inputs to the
internal state machine. The state machine outputs dictate the
function of the device. The appropriate device bus operations
table lists the inputs and control levels required, and the
resulting output. The following subsections describe each of
these operations in further detail.
Device Bus Operations
This section describes the requirements and use of the
device bus operations, which are initiated through the
internal command register. The command register itself does
not occupy any addressable memory location. The register is
composed of latches that store the commands, along with
the address and data information needed to execute the
Table 1. A29L320A Device Bus Operations
Operation
Read
Write
Accelerated
Program
Standby
Output Disable
Reset
CE
OE
WE RESET
WP /
ACC
A0 - A20
(Note 1)
I/O0 - I/O7
I/O8 - I/O15
BYTE =VIH
BYTE =VIL
I/O8~I/O14=High-Z
I/O15=A-1
L
L
L
L
H
H
H
L
L
H
H
H
L/H
(Note 3)
VHH
AIN
AIN
AIN
DOUT
(Note 4)
(Note 4)
DOUT
(Note 4)
(Note 4)
VCC ±
0.3 V
L
X
X
H
X
High-Z
High-Z
High-Z
H
H
VCC ±
0.3 V
H
L/H
L/H
X
X
High-Z
High-Z
High-Z
High-Z
High-Z
X
X
X
L
High-Z
High-Z
Sector Address,
L/H
Sector Protect
(Note 4)
X
X
L
H
L
VID
A6=L, A1=H, A0=L
(Note 2)
Sector Address,
Sector Unprotect
L/H
(Note 4)
X
X
L
H
L
VID
A6=H, A1=H, A0=L
(Note 2)
Temporary Sector
X
X
X
VID
L/H
AIN
(Note 4)
(Note 4)
High-Z
Unprotect
Legend:
L = Logic Low = VIL, H = Logic High = VIH, VID = 8.5V-10.5V, VHH = 8.5V-10.5V, X = Don't Care, DIN = Data In, DOUT = Data Out, AIN = Address In
Notes:
1. Addresses are A20:A0 in word mode ( BYTE=VIH), A20: A-1 in byte mode ( BYTE =VIL).
2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See “Sector/Sector
Block Protection and Unprotection”.
3. If WP /ACC=VIL, the two outermost boot sectors remain protected. If WP /ACC=VIH, the two outermost boot sector
protection depends on whether they were last protected or unprotected using the method described in
“Sector/Sector Block Protection and Unprotection. If WP /ACC = VHH, all sectors are unprotected.
4. DIN or DOUT as required by command sequence, data polling, or sector protection algorithm.
(November, 2007, Version 1.1)
5
AMIC Technology, Corp.
A29L320A Series
Characteristics" section contains timing specification tables
and timing diagrams for write operations.
Word/Byte Configuration
The BYTE pin determines whether the I/O pins I/O15-I/O0
operate in the byte or word configuration. If the BYTE pin is
set at logic ”1”, the device is in word configuration, I/O15-I/O0
are active and controlled by CE and OE .
Program and Erase Operation Status
During an erase or program operation, the system may
check the status of the operation by reading the status bits
on I/O7 - I/O0. Standard read cycle timings and ICC read
specifications apply. Refer to "Write Operation Status" for
more information, and to each AC Characteristics section for
timing diagrams.
If the BYTE pin is set at logic “0”, the device is in byte
configuration, and only I/O0-I/O7 are active and controlled by
CE and OE . I/O8-I/O14 are tri-stated, and I/O15 pin is used
as an input for the LSB(A-1) address function.
Standby Mode
Requirements for Reading Array Data
When the system is not reading or writing to the device, it
can place the device in the standby mode. In this mode,
current consumption is greatly reduced, and the outputs are
placed in the high impedance state, independent of the OE
input.
To read array data from the outputs, the system must drive
the CE and OE pins to VIL. CE is the power control and
selects the device. OE is the output control and gates array
data to the output pins. WE should remain at VIH all the time
during read operation. The BYTE pin determines whether
the device outputs array data in words and bytes. The
internal state machine is set for reading array data upon
device power-up, or after a hardware reset. This ensures that
no spurious alteration of the memory content occurs during
the power transition. No command is necessary in this mode
to obtain array data. Standard microprocessor read cycles
that assert valid addresses on the device address inputs
produce valid data on the device data outputs. The device
remains enabled for read access until the command register
contents are altered.
See "Reading Array Data" for more information. Refer to the
AC Read Operations table for timing specifications and to the
Read Operations Timings diagram for the timing waveforms,
lCC1 in the DC Characteristics table represents the active
current specification for reading array data.
The device enters the CMOS standby mode when the CE &
RESET pins are both held at VCC ± 0.3V. (Note that this is a
more restricted voltage range than VIH.) If CE and RESET
are held at VIH, but not within VCC ± 0.3V, the device will be
in the standby mode, but the standby current will be greater.
The device requires the standard access time (tCE) before it
is ready to read data.
If the device is deselected during erasure or programming,
the device draws active current until the operation is
completed.
ICC3 and ICC4 in the DC Characteristics tables represent the
standby current specification.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device energy
consumption. The device automatically enables this mode
when addresses remain stable for tACC +30ns. The automatic
sleep mode is independent of the CE , WE and OE control
signals. Standard address access timings provide new data
when addresses are changed. While in sleep mode, output
data is latched and always available to the system. ICC4 in the
DC Characteristics table represents the automatic sleep
mode current specification.
Writing Commands/Command Sequences
To write a command or command sequence (which includes
programming data to the device and erasing sectors of
memory), the system must drive WE and CE to VIL, and
OE to VIH. For program operations, the BYTE pin
determines whether the device accepts program data in
bytes or words, Refer to “Word/Byte Configuration” for more
information. The device features an Unlock Bypass mode to
facilitate faster programming. Once the device enters the
Unlock Bypass mode, only two write cycles are required to
program a word or byte, instead of four. The “
Word / Byte Program Command Sequence” section has
details on programming data to the device using both
standard and Unlock Bypass command sequence. An erase
operation can erase one sector, multiple sectors, or the
entire device. The Sector Address Tables indicate the
address range that each sector occupies. A "sector address"
consists of the address inputs required to uniquely select a
sector. See the "Command Definitions" section for details on
erasing a sector or the entire chip, or suspending/resuming
the erase operation.
After the system writes the autoselect command sequence,
the device enters the autoselect mode. The system can then
read autoselect codes from the internal register (which is
separate from the memory array) on I/O7 - I/O0. Standard
read cycle timings apply in this mode. Refer to the
"Autoselect Mode" and "Autoselect Command Sequence"
sections for more information.
ICC2 in the DC Characteristics table represents the active
current specification for the write mode. The "AC
(November, 2007, Version 1.1)
Output Disable Mode
When the OE input is at VIH, output from the device is
disabled. The output pins are placed in the high impedance
state.
RESET : Hardware Reset Pin
The RESET pin provides a hardware method of resetting
the device to reading array data. When the system drives the
RESET pin low for at least a period of tRP, the device
immediately terminates any operation in progress, tristates
all data output pins, and ignores all read/write attempts for
the duration of the RESET pulse. The device also resets the
internal state machine to reading array data. The operation
that was interrupted should be reinitiated once the device is
ready to accept another command sequence, to ensure data
integrity.
Current is reduced for the duration of the RESET pulse.
When RESET is held at VSS ± 0.3V, the device draws
CMOS standby current (ICC4 ). If RESET is held at VIL but not
within VSS ± 0.3V, the standby current will be greater.
6
AMIC Technology, Corp.
A29L320A Series
RY/ BY to determine whether the reset operation is
complete. If RESET is asserted when a program or erase
operation is not executing (RY/ BY pin is “1”), the reset
operation is completed within a time of tREADY (not during
Embedded Algorithms). The system can read data tRH after
the RESET pin return to VIH.
Refer to the AC Characteristics tables for RESET
parameters and diagram.
The RESET pin may be tied to the system reset circuitry. A
system reset would thus also reset the Flash memory,
enabling the system to read the boot-up firmware from the
Flash memory.
If RESET is asserted during a program or erase operation,
the RY/ BY pin remains a “0” (busy) until the internal reset
operation is complete, which requires a time tREADY (during
Embedded Algorithms). The system can thus monitor
Table 2. A29L320A Top Boot Block Sector Address Table
Sector
A20-A12
Sector Size
(Kbytes/ Kwords)
Address Range (in hexadecimal)
Byte Mode (x8)
Word Mode (x16)
SA0
000000XXX
64/32
000000 - 00FFFF
000000 - 007FFF
SA1
000001XXX
64/32
010000 - 01FFFF
008000 - 00FFFF
SA2
000010XXX
64/32
020000 - 02FFFF
010000 - 017FFF
SA3
000011XXX
64/32
030000 - 03FFFF
018000 - 01FFFF
SA4
000100XXX
64/32
040000 - 04FFFF
020000 - 027FFF
SA5
000101XXX
64/32
050000 - 05FFFF
028000 - 02FFFF
SA6
000110XXX
64/32
060000 - 06FFFF
030000 - 037FFF
SA7
000111XXX
64/32
070000 - 07FFFF
038000 - 03FFFF
SA8
001000XXX
64/32
080000 - 08FFFF
040000 - 047FFF
SA9
001001XXX
64/32
090000 - 09FFFF
048000 - 04FFFF
SA10
001010XXX
64/32
0A0000 - 0AFFFF
050000 - 057FFF
SA11
001011XXX
64/32
0B0000 - 0BFFFF
058000 - 05FFFF
SA12
001100XXX
64/32
0C0000 - 0CFFFF
060000 - 067FFF
SA13
001101XXX
64/32
0D0000 - 0DFFFF
068000 - 06FFFF
SA14
001110XXX
64/32
0E0000 - 0EFFFF
070000 - 077FFF
SA15
001111XXX
64/32
0F0000 - 0FFFFF
078000 - 07FFFF
SA16
010000XXX
64/32
100000 - 10FFFF
080000 - 087FFF
SA17
010001XXX
64/32
110000 - 11FFFF
088000 - 08FFFF
SA18
010010XXX
64/32
120000 - 12FFFF
090000 - 097FFF
SA19
010011XXX
64/32
130000 - 13FFFF
098000 - 09FFFF
SA20
010100XXX
64/32
140000 - 14FFFF
0A0000 - 0A7FFF
SA21
010101XXX
64/32
150000 - 15FFFF
0A8000 - 0AFFFF
SA22
010110XXX
64/32
160000 - 16FFFF
0B0000 - 0B7FFF
SA23
010111XXX
64/32
170000 - 17FFFF
0B8000 - 0BFFFF
SA24
011000XXX
64/32
180000 - 18FFFF
0C0000 - 0C7FFF
SA25
011001XXX
64/32
190000 - 19FFFF
0C8000 - 0CFFFF
SA26
011010XXX
64/32
1A0000 - 1AFFFF
0D0000 - 0D7FFF
SA27
011011XXX
64/32
1B0000 - 1BFFFF
0D8000 - 0DFFFF
SA28
011100XXX
64/32
1C0000 - 1CFFFF
0E0000 - 0E7FFF
SA29
011101XXX
64/32
1D0000 - 1DFFFF
0E8000 - 0EFFFF
SA30
011110XXX
64/32
1E0000 - 1EFFFF
0F0000 - 0F7FFF
SA31
011111XXX
64/32
1F0000 - 1FFFFF
0F8000 - 0FBFFF
SA32
100000XXX
64/32
200000 - 20FFFF
100000 - 107FFF
SA33
100001XXX
64/32
210000 - 21FFFF
108000 - 10FFFF
SA34
100010XXX
64/32
220000 - 22FFFF
110000 - 17FFFF
(November, 2007, Version 1.1)
7
AMIC Technology, Corp.
A29L320A Series
Table 2. A29L320A Top Boot Block Sector Address Table
Sector
A20-A12
Sector Size
(Kbytes/ Kwords)
Address Range (in hexadecimal)
Byte Mode (x8)
Word Mode (x16)
SA35
100011XXX
64/32
230000 - 23FFFF
118000 - 11FFFF
SA36
100100XXX
64/32
240000 - 24FFFF
120000 - 127FFF
SA37
100101XXX
64/32
250000 - 25FFFF
128000 - 12FFFF
SA38
100110XXX
64/32
260000 - 26FFFF
130000 - 137FFF
SA39
100111XXX
64/32
270000 - 27FFFF
138000 - 13FFFF
SA40
101000XXX
64/32
280000 - 28FFFF
140000 - 147FFF
SA41
101001XXX
64/32
290000 - 29FFFF
148000 - 14FFFF
SA42
101010XXX
64/32
2A0000 - 2AFFFF
150000 - 157FFF
SA43
101011XXX
64/32
2B0000 - 2BFFFF
158000 - 15FFFF
SA44
101100XXX
64/32
2C0000 - 2CFFFF
160000 - 167FFF
SA45
101101XXX
64/32
2D0000 - 2DFFFF
168000 - 16FFFF
SA46
101110XXX
64/32
2E0000 - 2EFFFF
170000 - 177FFF
SA47
101111XXX
64/32
2F0000 - 2FFFFF
178000 - 17FFFF
SA48
110000XXX
64/32
300000 - 30FFFF
180000 - 187FFF
SA49
110001XXX
64/32
310000 - 31FFFF
188000 - 18FFFF
SA50
110010XXX
64/32
320000 - 32FFFF
190000 - 197FFF
SA51
110011XXX
64/32
330000 - 33FFFF
198000 - 19FFFF
SA52
110100XXX
64/32
340000 - 34FFFF
1A0000 - 1A7FFF
SA53
110101XXX
64/32
350000 - 35FFFF
1A8000 - 1AFFFF
SA54
110110XXX
64/32
360000 - 36FFFF
1B0000 - 1B7FFF
SA55
110111XXX
64/32
370000 - 37FFFF
1B8000 - 1BFFFF
SA56
111000XXX
64/32
380000 - 38FFFF
1C0000 - 1C7FFF
SA57
111001XXX
64/32
390000 - 39FFFF
1C8000 - 1CFFFF
SA58
111010XXX
64/32
3A0000 - 3AFFFF
1D0000 - 1D7FFF
SA59
111011XXX
64/32
3B0000 - 3BFFFF
1D8000 - 1DFFFF
SA60
111100XXX
64/32
3C0000 - 3CFFFF
1E0000 - 1E7FFF
SA61
111101XXX
64/32
3D0000 - 3DFFFF
1E8000 - 1EFFFF
SA62
111110XXX
64/32
3E0000 - 3EFFFF
1F0000 - 1F7FFF
SA63
111111000
8/4
3F0000 - 3FFFFF
1F8000 - 1F8FFF
SA64
111111001
8/4
3F2000 - 3F3FFF
1F9000 - 1F9FFF
SA65
111111010
8/4
3F4000 - 3F5FFF
1FA000 - 1FAFFF
SA66
111111011
8/4
3F6000 - 3F7FFF
1FB000 - 1FBFFF
SA67
111111100
8/4
3F8000 - 3F9FFF
1FC000 - 1FCFFF
SA68
111111101
8/4
3FA000 - 3FBFFF
1FD000 - 1FDFFF
SA69
111111110
8/4
3FC000 - 3FDFFF
1FE000 - 1FEFFF
SA70
111111111
8/4
3FE000 - 3FFFFF
1FF000 - 1FFFFF
Note:
Address range is A20 : A-1 in byte mode and A20 : A0 in word mode. See “Word/Byte Configuration” section.
(November, 2007, Version 1.1)
8
AMIC Technology, Corp.
A29L320A Series
Table 3. A29L320A Bottom Boot Block Sector Address Table
Sector
A20 -A12
Sector Size
Address Range (in hexadecimal)
(Kbytes/ Kwords)
Byte Mode (x8)
Word Mode (x16)
SA0
000000000
8/4
000000 - 001FFF
000000 - 000FFF
SA1
000000001
8/4
002000 - 003FFF
001000 - 001FFF
SA2
000000010
8/4
004000 - 005FFF
002000 - 002FFF
SA3
000000011
8/4
006000 - 007FFF
003000 - 003FFF
SA4
000000100
8/4
008000 - 009FFF
004000 - 004FFF
SA5
000000101
8/4
00A000 - 00BFFF
005000 - 005FFF
SA6
000000110
8/4
00C000 - 00DFFF
006000 - 006FFF
SA7
000000111
8/4
00E000 - 00FFFF
007000 - 007FFF
SA8
000001XXX
64/32
010000 - 01FFFF
008000 - 00FFFF
SA9
000010XXX
64/32
020000 - 02FFFF
010000 - 017FFF
SA10
000011XXX
64/32
030000 - 03FFFF
018000 - 01FFFF
SA11
000100XXX
64/32
040000 - 04FFFF
020000 - 027FFF
SA12
000101XXX
64/32
050000 - 05FFFF
028000 - 02FFFF
SA13
000110XXX
64/32
060000 - 06FFFF
030000 - 037FFF
SA14
000111XXX
64/32
070000 - 07FFFF
038000 - 03FFFF
SA15
001000XXX
64/32
080000 - 08FFFF
040000 - 047FFF
SA16
001001XXX
64/32
090000 - 09FFFF
048000 - 04FFFF
SA17
001010XXX
64/32
0A0000 - 0AFFFF
050000 - 057FFF
SA18
001011XXX
64/32
0B0000 - 0BFFFF
058000 - 05FFFF
SA19
001100XXX
64/32
0C0000 - 0CFFFF
060000 - 067FFF
SA20
001101XXX
64/32
0D0000 - 0DFFFF
068000 - 06FFFF
SA21
001110XXX
64/32
0E0000 - 0EFFFF
070000 - 077FFF
SA22
001111XXX
64/32
0F0000 - 0FFFFF
078000 - 07FFFF
SA23
010000XXX
64/32
100000 - 10FFFF
080000 - 087FFF
SA24
010001XXX
64/32
110000 - 11FFFF
088000 - 07FFFF
SA25
010010XXX
64/32
120000 - 12FFFF
090000 - 097FFF
SA26
010011XXX
64/32
130000 - 13FFFF
098000 - 09FFFF
SA27
010100XXX
64/32
140000 - 14FFFF
0A0000 - 0A7FFF
SA28
1010101XXX
64/32
140000 - 14FFFF
0A8000 - 0AFFFF
SA29
010110XXX
64/32
160000 - 16FFFF
0B0000 - 0B7FFF
SA30
010111XXX
64/32
170000 - 17FFFF
0B8000 - 0BFFFF
SA31
011000XXX
64/32
180000 - 18FFFF
0C0000 - 0C7FFF
SA32
011001XXX
64/32
190000 - 19FFFF
0C8000 - 0CFFFF
SA33
011010XXX
64/32
1A0000 - 1AFFFF
0D0000 - 0D7FFF
SA34
011011XXX
64/32
1B0000 - 1BFFFF
0D8000 - 0DFFFF
(November, 2007, Version 1.1)
9
AMIC Technology, Corp.
A29L320A Series
Table 3. A29L320A Bottom Boot Block Sector Address Table
Sector
A20 -A12
Sector Size
Address Range (in hexadecimal)
(Kbytes/ Kwords)
Byte Mode (x8)
Word Mode (x16)
SA35
011100XXX
64/32
1C0000 - 1CFFFF
0E0000 - 0E7FFF
SA36
011101XXX
64/32
1D0000 - 1DFFFF
0E8000 - 0EFFFF
SA37
011110XXX
64/32
1E0000 - 1EFFFF
0F0000 - 0F7FFF
SA38
011111XXX
64/32
1F0000 - 1FFFFF
0F8000 - 0FFFFF
SA39
100000XXX
64/32
200000 - 20FFFF
100000 - 107FFF
SA40
100001XXX
64/32
210000 - 21FFFF
108000 - 10FFFF
SA41
100010XXX
64/32
220000 - 22FFFF
110000 - 117FFF
SA42
100011XXX
64/32
230000 - 23FFFF
118000 - 11FFFF
SA43
100100XXX
64/32
240000 - 24FFFF
120000 - 127FFF
SA44
100101XXX
64/32
250000 - 25FFFF
128000 - 12FFFF
SA45
100110XXX
64/32
260000 - 26FFFF
130000 - 137FFF
SA46
100111XXX
64/32
270000 - 27FFFF
138000 - 13FFFF
SA47
101000XXX
64/32
280000 - 28FFFF
140000 - 147FFF
SA48
101001XXX
64/32
290000 - 29FFFF
148000 - 14FFFF
SA49
101010XXX
64/32
2A0000 - 2AFFFF
150000 - 157FFF
SA50
101011XXX
64/32
2B0000 - 2BFFFF
158000 - 15FFFF
SA51
101100XXX
64/32
2C0000 - 2CFFFF
160000 - 167FFF
SA52
101101XXX
64/32
2D0000 - 2DFFFF
168000 - 16FFFF
SA53
101110XXX
64/32
2E0000 - 2EFFFF
170000 - 177FFF
SA54
101111XXX
64/32
2F0000 - 2FFFFF
178000 - 17FFFF
SA55
110000XXX
64/32
300000 - 30FFFF
180000 - 187FFF
SA56
110001XXX
64/32
310000 - 31FFFF
188000 - 18FFFF
SA57
110010XXX
64/32
320000 - 32FFFF
190000 - 197FFF
SA58
110011XXX
64/32
330000 - 33FFFF
198000 - 19FFFF
SA59
110100XXX
64/32
340000 - 34FFFF
1A0000 - 1A7FFF
SA60
110101XXX
64/32
350000 - 35FFFF
1A8000 - 1AFFFF
SA61
110110XXX
64/32
360000 - 36FFFF
1B0000 - 1B7FFF
SA62
110111XXX
64/32
370000 - 37FFFF
1B8000 - 1BFFFF
SA63
111000XXX
64/32
380000 - 38FFFF
1C0000 - 1C7FFF
SA64
111001XXX
64/32
390000 - 39FFFF
1C8000 - 1CFFFF
SA65
111010XXX
64/32
3A0000 - 3AFFFF
1D0000 - 1D7FFF
SA66
111011XXX
64/32
3B0000 - 3BFFFF
1D8000 - 1DFFFF
SA67
111100XXX
64/32
3C0000 - 3CFFFF
1E0000 - 1E7FFF
SA68
111101XXX
64/32
3D0000 - 3DFFFF
1E8000 - 1EFFFF
SA69
111110XXX
64/32
3E0000 - 3EFFFF
1F0000 - 1F7FFF
SA70
111111XXX
64/32
3F0000 - 3FFFFF
1F8000 - 1FFFFF
Note:
Address range is A20 : A-1 in byte mode and A20 : A0 in word mode. See “Word/Byte Configuration” section.
(November, 2007, Version 1.1)
10
AMIC Technology, Corp.
A29L320A Series
protection, the sector address must appear on the
appropriate highest order address bits. Refer to the
corresponding Sector Address Tables. The Command
Definitions table shows the remaining address bits that are
don't care. When all necessary bits have been set as
required, the programming equipment may then read the
corresponding identifier code on I/O7 - I/O0.To access the
autoselect codes in-system, the host system can issue the
autoselect command via the command register, as shown in
the Command Definitions table. This method does not
require VID. See "Command Definitions" for details on using
the autoselect mode.
Autoselect Mode
The autoselect mode provides manufacturer and device
identification, and sector protection verification, through
identifier codes output on I/O7 - I/O0. This mode is primarily
intended for programming equipment to automatically match
a device to be programmed with its corresponding
programming algorithm. However, the autoselect codes can
also be accessed in-system through the command register.
When using programming equipment, the autoselect mode
requires VID (8.5V to 10.5V) on address pin A9. Address pins
A6, A1, and A0 must be as shown in Autoselect Codes (High
Voltage Method) table. In addition, when verifying sector
Table 4. A29L320A Autoselect Codes (High Voltage Method)
Description
Mode
Manufacturer ID: AMIC
Device ID:
CE
OE
WE
A20
to
A12
A11
to
A10
A9
A8
to
A7
A6
A5
to
A2
A1
A0
I/O8
to
I/O15
I/O7
to
I/O0
L
L
H
X
X
VID
X
L
X
L
L
X
37h
22h
F6h
L
L
H
X
X
VID
X
L
X
L
H
Word
A29L320A
(Top Boot Block)
Byte
X
F6h
Device ID:
Word
22h
F9h
X
F9h
X
7Fh
X
01h
(protected)
X
00h
(unprotected)
A29L320A
(Bottom Boot Block)
L
L
H
X
X
VID
X
L
X
L
H
Byte
Continuation ID
Sector Protection Verification
L
L
L
L
H
H
X
SA
X
X
VID
VID
X
X
L
L
X
X
H
H
H
L
L=Logic Low= VIL, H=Logic High=VIH, SA=Sector Address, X=Don’t Care.
Note: The autoselect codes may also be accessed in-system via command sequences.
(November, 2007, Version 1.1)
11
AMIC Technology, Corp.
A29L320A Series
Sector/Sector Block Protection and Unprotection
(Note: For the following discussion, the term “sector” applies
to both sectors and sector blocks. A sector block consists of
two or more adjacent sectors that are protected or
unprotected at the same time (see Tables 5 and 6).
Table 5. Top Boot Sector/Sector Block Addresses for
Protection/Unprotection
Table 6. Bottom Boot Sector/Sector Block Addresses for
Protection/Unprotection
Sector /
Sector Block
SA0
A20–A12
Sector / Sector Block Size
Sector /
Sector Block
000000XXX
000001XXX
000010XXX
000011XXX
64 Kbytes
SA70
192 (3x64) Kbytes
SA69- SA67
A20–A12
Sector / Sector Block Size
64 Kbytes
256 (4x64) Kbytes
SA4-SA7
0001XXXXX
256 (4x64) Kbytes
SA66- SA63
111111XXX
111110XXX
111101XXX
111100XXX
1110XXXXX
SA8-SA11
0010XXXXX
256 (4x64) Kbytes
SA62- SA59
1101XXXXX
256 (4x64) Kbytes
SA12-SA15
0011XXXXX
256 (4x64) Kbytes
SA58- SA55
1100XXXXX
256 (4x64) Kbytes
SA16-SA19
0100XXXXX
256 (4x64) Kbytes
SA54- SA51
1011XXXXX
256 (4x64) Kbytes
SA20-SA23
0101XXXXX
256 (4x64) Kbytes
SA50- SA47
1010XXXXX
256 (4x64) Kbytes
SA24-SA27
0110XXXXX
256 (4x64) Kbytes
SA46-SA43
1001XXXXX
256 (4x64) Kbytes
SA28-SA31
0111XXXXX
SA42-SA39
1000XXXXX
256 (4x64) Kbytes
SA32-SA35
1000XXXXX
256 (4x64) Kbytes
SA38-SA35
0111XXXXX
256 (4x64) Kbytes
SA36-SA39
1001XXXXX
256 (4x64) Kbytes
SA34-SA31
0110XXXXX
256 (4x64) Kbytes
SA40-SA43
1010XXXXX
256 (4x64) Kbytes
SA30-SA27
0101XXXXX
256 (4x64) Kbytes
SA44-SA47
1011XXXXX
256 (4x64) Kbytes
SA26-SA23
0100XXXXX
256 (4x64) Kbytes
SA48-SA51
1100XXXXX
256 (4x64) Kbytes
SA22-SA19
0011XXXXX
256 (4x64) Kbytes
SA52-SA55
1101XXXXX
256 (4x64) Kbytes
SA18-SA15
0010XXXXX
256 (4x64) Kbytes
SA56-SA59
256 (4x64) Kbytes
SA14-SA11
0001XXXXX
256 (4x64) Kbytes
SA63
1110XXXXX
111100XXX
111101XXX
111110XXX
111111000
SA64
111111001
8 Kbytes
SA65
111111010
8 Kbytes
SA66
111111011
8 Kbytes
SA1-SA3
SA60-SA62
SA67
111111100
256 (4x64) Kbytes
192 (3x64) Kbytes
SA7
000001XXX
000010XXX
000011XXX
000000111
SA6
000000110
8 Kbytes
SA5
000000101
8 Kbytes
SA4
000000100
8 Kbytes
000000011
8 Kbytes
SA10-SA8
8 Kbytes
8 Kbytes
192 (3x64) Kbytes
192 (3x64) Kbytes
8 Kbytes
SA68
111111101
8 Kbytes
SA3
SA69
111111110
8 Kbytes
SA2
000000010
8 Kbytes
SA70
111111111
8 Kbytes
SA1
000000001
8 Kbytes
SA0
000000000
8 Kbytes
(November, 2007, Version 1.1)
12
AMIC Technology, Corp.
A29L320A Series
Sector Protection/Unprotection
Write Pulse "Glitch" Protection
The hardware sector protection feature disables both
program and erase operations in any sector. The hardware
sector unprotection feature re-enables both program and
erase operations in previously protected sectors.
It is possible to determine whether a sector is protected or
unprotected. See “Autoselect Mode” for details.
Sector protection / unprotection can be implemented via two
methods. The primary method requires VID on the
RESET pin only, and can be implemented either in-system or
via programming equipment. Figure 2 shows the algorithm
and the Sector Protect / Unprotect Timing Diagram illustrates
the timing waveforms for this feature. This method uses
standard microprocessor bus cycle timing. For sector
unprotect, all unprotected sectors must first be protected
prior to the first sector unprotect write cycle. The alternate
method for protection and unprotection is by software sector
block protect/unprotect command. See Figure 2 for
Command Flow.
The device is shipped with all sectors unprotected.
It is possible to determine whether a sector is protected or
unprotected. See "Autoselect Mode" for details.
Noise pulses of less than 5ns (typical) on OE , CE or WE
do not initiate a write cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE =VIL,
CE = VIH or WE = VIH. To initiate a write cycle, CE and
WE must be a logical zero while OE is a logical one.
Power-Up Write Inhibit
If WE = CE = VIL and OE = VIH during power up, the
device does not accept commands on the rising edge of
WE . The internal state machine is automatically reset to
reading array data on the initial power-up.
Temporary Sector Unprotect
This feature allows temporary unprotection of previous
protected sectors to change data in-system. The Sector
Unprotect mode is activated by setting the RESET pin to VID.
During this mode, formerly protected sectors can be
programmed or erased by selecting the sector addresses.
Once VID is removed from the RESET pin, all the previously
protected sectors are protected again. Figure 1 shows the
algorithm, and the Temporary Sector Unprotect diagram
shows the timing waveforms, for this feature.
Hardware Data Protection
The requirement of command unlocking sequence for
programming or erasing provides data protection against
inadvertent writes (refer to the Command Definitions table).
In addition, the following hardware data protection measures
prevent accidental erasure or programming, which might
otherwise be caused by spurious system level signals during
VCC power-up transitions, or from system noise. The device
is powered up to read array data to avoid accidentally writing
data to the array.
(November, 2007, Version 1.1)
13
AMIC Technology, Corp.
A29L320A Series
START
START
555/AA + 2AA/55 + 555/77
RESET = VID
(Note 1)
(Note 1)
Perform Erase or
Program Operations
Perform Erase or
Program Operations
XXX/F0
(Reset Command)
RESET = VIH
Soft-ware Temporary
Sector Unprotect
Completed
(Note 2)
Temporary Sector
Unprotect
Completed (Note 2)
Notes:
1. All protected sectors unprotected (If WP/ACC=VIL,
outermost boot sectors will remain protected).
2. All previously protected sectors are protected once again.
Notes:
1. All protected sectors unprotected (If WP/ACC=VIL,
outermost boot sectors will remain protected).
2. All previously protected sectors are protected once again.
Figure 1-2. Temporary Sector Unprotect Operation by Software Mode
Figure 1-1. Temporary Sector Unprotect Operation by RESET Mode
(November, 2007, Version 1.1)
14
AMIC Technology, Corp.
A29L320A Series
START
START
Protect all sectors:
The indicated portion of
the sector protect
algorithm must be
performed for all
unprotected sectors prior
to issuing the first sector
unprotect address
PLSCNT=1
RESET=VID
Wait 1 us
No
Temporary Sector
Unprotect Mode
PLSCNT=1
RESET=VID
Wait 1 us
No
First Write
Cycle=60h?
Yes
Temporary Sector
Unprotect Mode
All sectors
protected?
Sector Protec:
Write 60h to sector
address with A6=0,
A1=1, A0=0
Yes
Set up first sector
address
Sector Unprotect:
Write 60h to sector
address with A6=1,
A1=1, A0=0
Wait 150 us
Increment
PLSCNT
No
Yes
Set up sector
address
Verify Sector
Protect: Write 40h
to sector address
with A6=0, A1=1,
A0=0
First Write
Cycle=60h?
Reset
PLSCNT=1
Wait 15 ms
Read from
sector address
with A6=0,
A1=1, A0=0
Verify Sector
Unprotect : Write
40h to sector
address with A6=1,
A1=1, A0=0
Increment
PLSCNT
No
PLSCNT
=25?
No
Read from sector
address with A6=1,
A1=1, A0=0
Data=01h?
No
Device failed
Protect another
sector?
PLSCNT=
1000?
Yes
No
Yes
No
Remove VID
from RESET
Device failed
Write reset
command
Sector Protect
Algorithm
Set up
next sector
address
Yes
Yes
Sector Protect
complete
Data=00h?
Yes
Last sector
verified?
No
Yes
Remove VID
from RESET
Sector Unprotect
Algorithm
Write reset
Command
Sector Unprotect
complete
Figure 2-1. In-System Sector Protect/Unprotect
Algorithms
(November, 2007, Version 1.1)
15
AMIC Technology, Corp.
A29L320A Series
START
START
PLSCNT=1
555/AA + 2AA/55 +
555/77
Wait 1 us
No
Temporary Sector
Unprotect Mode
PLSCNT=1
Protect all sectors:
The indicated portion of
the sector protect
algorithm must be
performed for all
unprotected sectors prior
to issuing the first sector
unprotect address
555/AA + 2AA/55 +
555/77
Wait 1 us
No
First Write
Cycle=60h?
Yes
Temporary Sector
Unprotect Mode
All sectors
protected?
Sector Protect:
Write 60h to sector
address with A6=0,
A1=1, A0=0
Yes
Set up first sector
address
Sector Unprotect:
Write 60h to sector
address with A6=1,
A1=1, A0=0
Wait 150 us
Increment
PLSCNT
No
Yes
Set up sector
address
Verify Sector
Protect: Write 40h
to sector address
with A6=0, A1=1,
A0=0
First Write
Cycle=60h?
Reset
PLSCNT=1
Wait 15 ms
Read from
sector address
with A6=0,
A1=1, A0=0
Verify Sector
Unprotect : Write
40h to sector
address with A6=1,
A1=1, A0=0
Increment
PLSCNT
No
PLSCNT
=25?
No
Read from sector
address with A6=1,
A1=1, A0=0
Data=01h?**
No
Device failed
Protect another
sector?
PLSCNT=
1000?
Yes
No
Yes
No
Write reset
command
Sector Protect
Algorithm
Set up
next sector
address
Yes
Yes
Device failed
Sector Protect
complete
Data=00h?**
Yes
Last sector
verified?
No
Yes
Sector Unprotect
Algorithm
Write reset
Command
Sector Unprotect
complete
Note: The term “sector” in the figure applies to both sectors and sector blocks
* No other command is allowed during this process
** Access time is 200ns-300ns
Figure 2-2. Software Sector/Sector Block Protection and Unprotection Algorithms
(November, 2007, Version 1.1)
16
AMIC Technology, Corp.
A29L320A Series
ready to read array data. The system can read CFI
information at the addresses given in Table 5-8. In word
mode, the upper address bits (A7-MSB) must be all zeros.
To terminate reading CFI data, the system must write the
reset command.
The system can also write the CFI query command when the
device is in the autoselect mode. The device enters the CFI
query mode, and the system can read CFI data at the
addresses given in Table 5-8. The system must write the
reset command to return the device to the autoselect mode.
Common Flash Memory Interface (CFI)
The Common Flash Interface (CFI) specification outlines
device and host system software interrogation handshake,
which allows specific vendor-specified software algorithms to
be used for entire families of devices. Software support can
then be device-independent, JEDEC ID-independent, and
forward- and backward-compatible for the specified flash
device families. Flash vendors can standardize their existing
interface for long-term compatibility.
This device enters the CFI Query mode when the system
writes the CFI Query command, 98h, to address 55h in word
mode (or address AAh in byte mode), any time the device is
Table 7. CFI Query Identification String
Addresses
Addresses
(Word Mode)
(Byte Mode)
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
20h
22h
24h
26h
28h
2Ah
2Ch
2Eh
30h
32h
34h
Data
0051h
0052h
0059h
0002h
0000h
0040h
0000h
0000h
0000h
0000h
0000h
Description
Query Unique ASCII string “QRY”
Primary OEM Command Set
Address for Primary Extended Table
Alternate OEM Command Set (00h = none exists)
Address for Alternate OEM Extended Table (00h = none exists)
Table 8. System Interface String
Addresses
Addresses
(Word Mode)
(Byte Mode)
1Bh
36h
0027h
1Ch
38h
0036h
Data
Description
VCC Min. (write/erase)
I/O7- I/O4 : volt, I/O3- I/O0: 100 millivolt
VCC Max. (write/erase)
I/O7- I/O4: volt, I/O3- I/O0: 100 millivolt
1Dh
3Ah
0000h
Vpp Min. voltage (00h = no Vpp pin present)
1Eh
3Ch
0000h
Vpp Max. voltage (00h = no Vpp pin present)
1Fh
3Eh
0004h
Typical timeout per single byte/word write 2N μs
20h
40h
0000h
Typical timeout for Min. size buffer write 2N μs (00h = not supported)
21h
42h
000Ah
Typical timeout per individual block erase 2N ms
22h
44h
0000h
Typical timeout for full chip erase 2N ms (00h = not supported)
23h
46h
0005h
Max. timeout for byte/word write 2N times typical
24h
48h
0000h
Max. timeout for buffer write 2N times typical
25h
4Ah
0004h
Max. timeout per individual block erase 2N times typical
26h
4Ch
0000h
Max. timeout for full chip erase 2N times typical (00h = not supported)
(November, 2007, Version 1.1)
17
AMIC Technology, Corp.
A29L320A Series
Table 9. Device Geometry Definition
Addresses
Addresses
(Word Mode)
(Byte Mode)
27h
4Eh
0016h
28h
50h
0002h
29h
52h
0000h
2Ah
54h
0000h
Max. number of byte in multi-byte write = 2N
2Bh
56h
0000h
(00h = not supported)
2Ch
58h
0002h
Number of Erase Block Regions within device
2Dh
5Ah
0007h
2Eh
5Ch
0000h
Erase Block Region 1 Information
2Fh
5Eh
0020h
(refer to the CFI specification)
30h
60h
0000h
31h
62h
003Eh
32h
64h
0000h
33h
66h
0000h
34h
68h
0001h
35h
6Ah
0000h
36h
6Ch
0000h
37h
6Eh
0000h
38h
40h
0000h
Data
39h
72h
0000h
3Ah
74h
0000h
3BH
76h
0000h
3Ch
78h
0000h
(November, 2007, Version 1.1)
Description
Device Size = 2N byte
Flash Device Interface description
Erase Block Region 2 Information
Erase Block Region 3 Information
Erase Block Region 4 Information
18
AMIC Technology, Corp.
A29L320A Series
Table 10. Primary Vendor-Specific Extended Query
Addresses
Addresses
(Word Mode)
(Byte Mode)
40h
80h
0050h
41h
82h
0052h
42h
84h
0049h
43h
86h
0031h
Major version number, ASCII
44h
88h
0031h
Minor version number, ASCII
45h
8Ah
0000h
Address Sensitive Unlock
Data
Description
Query-unique ASCII string “PRI”
0 = Required, 1 = Not Required
46h
8Ch
0002h
Erase Suspend
0 = Not Supported, 1 = To Read Only, 2 = To Read & Write
47h
8Eh
0001h
48h
90h
0001h
Sector Protect
0 = Not Supported, X = Number of sectors in per group
Sector Temporary Unprotect
00 = Not Supported, 01 = Supported
49h
92h
0004h
Sector Protect/Unprotect scheme
01 = 29F040 mode, 02 = 29F016 mode,
03 = 29F400 mode, 04 = 29L160 mode
4Ah
94h
0000h
Simultaneous Operation
00 = Not Supported, 01 = Supported
4Bh
96h
0000h
4Ch
98h
0000h
Burst Mode Type
00 = Not Supported, 01 = Supported
Page Mode Type
00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page
4Dh
9Ah
0085h
ACC (Acceleration) Supply Minimum
00 = Not Supported, D7-D4: Volt, D3-D0: 100mV
4Eh
9Ch
0095h
4Fh
9Eh
000Xh
ACC (Acceleration) Supply Maximum
00 = Not Supported, D7-D4: Volt, D3-D0: 100mV
Top/Bottom Boot Sector Flag
02 = Bottom Boot Device, 03h = Top Boot Device
(November, 2007, Version 1.1)
19
AMIC Technology, Corp.
A29L320A Series
Command Definitions
Autoselect Command Sequence
Writing specific address and data commands or sequences
into the command register initiates device operations. The
Command Definitions table defines the valid register
command sequences. Writing incorrect address and data
values or writing them in the improper sequence resets the
device to reading array data.
All addresses are latched on the falling edge of WE or CE ,
whichever happens later. All data is latched on the rising
edge of WE or CE , whichever happens first. Refer to the
appropriate timing diagrams in the "AC Characteristics"
section.
The autoselect command sequence allows the host system to
access the manufacturer and devices codes, and determine
whether or not a sector is protected. The Command
Definitions table shows the address and data requirements.
This method is an alternative to that shown in the Autoselect
Codes (High Voltage Method) table, which is intended for
PROM programmers and requires VID on address bit A9.
The autoselect command sequence is initiated by writing two
unlock cycles, followed by the autoselect command. The
device then enters the autoselect mode, and the system may
read at any address any number of times, without initiating
another command sequence.
A read cycle at address XX00h retrieves the manufacturer
code and another read cycle at XX11h retrieves the
continuation code. A read cycle at address XX01h returns the
device code. A read cycle containing a sector address (SA)
and the address 02h in returns 01h if that sector is protected,
or 00h if it is unprotected. Refer to the Sector Address tables
for valid sector addresses.
The system must write the reset command to exit the
autoselect mode and return to reading array data.
Reading Array Data
The device is automatically set to reading array data after
device power-up. No commands are required to retrieve
data. The device is also ready to read array data after
completing an Embedded Program or Embedded Erase
algorithm. After the device accepts an Erase Suspend
command, the device enters the Erase Suspend mode. The
system can read array data using the standard read timings,
except that if it reads at an address within erase-suspended
sectors, the device outputs status data. After completing a
programming operation in the Erase Suspend mode, the
system may once again read array data with the same
exception. See "Erase Suspend/Erase Resume Commands"
for more information on this mode.
The system must issue the reset command to re-enable the
device for reading array data if I/O5 goes high, or while in the
autoselect mode. See the "Reset Command" section, next.
See also "Requirements for Reading Array Data" in the
"Device Bus Operations" section for more information. The
Read Operations table provides the read parameters, and
Read Operation Timings diagram shows the timing diagram.
Word/Byte Program Command Sequence
The system may program the device by word or byte,
depending on the state of the BYTE pin. Programming is a
four-bus-cycle operation. The program command sequence is
initiated by writing two unlock write cycles, followed by the
program set-up command. The program address and data are
written next, which in turn initiate the Embedded Program
algorithm. The system is not required to provide further
controls or timings. The device automatically provides
internally generated program pulses and verify the
programmed cell margin. Table 9 shows the address and data
requirements for the byte program command sequence.
When the Embedded Program algorithm is complete, the
device then returns to reading array data and addresses are
longer latched. The system can determine the status of the
program operation by using I/O7, I/O6, or RY/ BY . See “White
Operation Status” for information on these status bits.
Any commands written to the device during the Embedded
Program Algorithm are ignored. Note that a hardware reset
immediately terminates the programming operation. The Byte
Program command sequence should be reinitiated once the
device has reset to reading array data, to ensure data
integrity.
Programming is allowed in any sequence and across sector
boundaries. A bit cannot be programmed from a “0” back to a
“1”. Attempting to do so may halt the operation and set I/O5 to
“1”, or cause the Data Polling algorithm to indicate the
operation was successful. However, a succeeding read will
show that the data is still “0”. Only erase operations can
convert a “0” to a “1”.
Reset Command
Writing the reset command to the device resets the device to
reading array data. Address bits are don't care for this
command. The reset command may be written between the
sequence cycles in an erase command sequence before
erasing begins. This resets the device to reading array data.
Once erasure begins, however, the device ignores reset
commands until the operation is complete.
The reset command may be written between the sequence
cycles in a program command sequence before
programming begins. This resets the device to reading array
data (also applies to programming in Erase Suspend mode).
Once programming begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the sequence
cycles in an autoselect command sequence. Once in the
autoselect mode, the reset command must be written to
return to reading array data (also applies to autoselect during
Erase Suspend).
If I/O5 goes high during a program or erase operation, writing
the reset command returns the device to reading array data
(also applies during Erase Suspend).
(November, 2007, Version 1.1)
20
AMIC Technology, Corp.
A29L320A Series
00h. Addresses are don’t care for both cycle. The device
returns to reading array data.
Figure 3 illustrates the algorithm for the program operation.
See the Erase/Program Operations in “AC Characteristics” for
parameters, and to Program Operation Timings for timing
diagrams.
START
Write Program
Command
Sequence
Chip Erase Command Sequence
Chip erase is a six-bus-cycle operation. The chip erase
command sequence is initiated by writing two unlock cycles,
followed by a set-up command. Two additional unlock write
cycles are then followed by the chip erase command, which
in turn invokes the Embedded Erase algorithm. The device
does not require the system to preprogram prior to erase. The
Embedded Erase algorithm automatically preprograms and
verifies the entire memory for an all zero data pattern prior to
electrical erase. The system is not required to provide any
controls or timings during these operations. The Command
Definitions table shows the address and data requirements
for the chip erase command sequence.
Any commands written to the chip during the Embedded
Erase algorithm are ignored. The system can determine the
status of the erase operation by using I/O7, I/O6, or I/O2. See
"Write Operation Status" for information on these status bits.
When the Embedded Erase algorithm is complete, the device
returns to reading array data and addresses are no longer
latched.
Figure 4 illustrates the algorithm for the erase operation. See
the Erase/Program Operations tables in "AC Characteristics"
for parameters, and to the Chip/Sector Erase Operation
Timings for timing waveforms.
Data Poll
from System
Embedded
Program
algorithm in
progress
Verify Data ?
No
Yes
Increment Address
No
Last Address ?
Yes
Programming
Completed
Sector Erase Command Sequence
Sector erase is a six-bus-cycle operation. The sector erase
command sequence is initiated by writing two unlock cycles,
followed by a set-up command. Two additional unlock write
cycles are then followed by the address of the sector to be
erased, and the sector erase command. The Command
Definitions table shows the address and data requirements
for the sector erase command sequence.
The device does not require the system to preprogram the
memory prior to erase. The Embedded Erase algorithm
automatically programs and verifies the sector for an all zero
data pattern prior to electrical erase. The system is not
required to provide any controls or timings during these
operations.
After the command sequence is written, a sector erase timeout of 50μs begins. During the time-out period, additional
sector addresses and sector erase commands may be
written. Loading the sector erase buffer may be done in any
sequence, and the number of sectors may be from one sector
to all sectors. The time between these additional cycles must
be less than 50μs, otherwise the last address and command
might not be accepted, and erasure may begin. It is
recommended that processor interrupts be disabled during
this time to ensure all commands are accepted. The
interrupts can be re-enabled after the last Sector Erase
command is written. If the time between additional sector
erase commands can be assumed to be less than 50μs, the
system need not monitor I/O3. Any command other than
Sector Erase or Erase Suspend during the time-out period
resets the device to reading array data. The system must
rewrite the command sequence and any additional sector
addresses and commands.
Note : See the appropriate Command Definitions table for
program command sequence.
Figure 3. Program Operation
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program
bytes or words to the device faster than using the standard
program command sequence. The unlock bypass command
sequence is initiated by first writing two unlock cycles. This is
followed by a third write cycle containing the unlock bypass
command, 20h. The device then enters the unlock bypass
mode. A two-cycle unlock bypass program command
sequence is all that is required to program in this mode. The
first cycle in this sequence contains the unlock bypass
program command, A0h; the second cycle contains the
program address and data. Additional data is programmed in
the same manner. This mode dispenses with the initial two
unlock cycles required in the standard program command
sequence, resulting in faster total programming time. Table 9
shows the requirements for the command sequence.
During the unlock bypass mode, only the Unlock Bypass
Program and Unlock Bypass Reset commands are valid. To
exit the unlock bypass mode, the system must issue the twocycle unlock bypass reset command sequence. The first
cycle must contain the data 90h; the second cycle the data
(November, 2007, Version 1.1)
21
AMIC Technology, Corp.
A29L320A Series
The system can monitor I/O3 to determine if the sector erase
timer has timed out. (See the " I/O3: Sector Erase Timer"
section.) The time-out begins from the rising edge of the final
WE pulse in the command sequence.
Once the sector erase operation has begun, only the Erase
Suspend command is valid. All other commands are ignored.
When the Embedded Erase algorithm is complete, the device
returns to reading array data and addresses are no longer
latched. The system can determine the status of the erase
operation by using I/O7, I/O6, or I/O2. Refer to "Write
Operation Status" for information on these status bits.
4 illustrates the algorithm for the erase operation. Refer to
the Erase/Program Operations tables in the "AC
Characteristics" section for parameters, and to the Sector
Erase Operations Timing diagram for timing waveforms.
The system must write the Erase Resume command
(address bits are "don't care") to exit the erase suspend
mode and continue the sector erase operation. Further writes
of the Resume command are ignored. Another Erase
Suspend command can be written after the device has
resumed erasing.
START
Write Erase
Command
Sequence
Erase Suspend/Erase Resume Commands
The Erase Suspend command allows the system to interrupt
a sector erase operation and then read data from, or
program data to, any sector not selected for erasure. This
command is valid only during the sector erase operation,
including the 50μs time-out period during the sector erase
command sequence. The Erase Suspend command is
ignored if written during the chip erase operation or
Embedded Program algorithm. Writing the Erase Suspend
command during the Sector Erase time-out immediately
terminates the time-out period and suspends the erase
operation. Addresses are "don't cares" when writing the
Erase Suspend command.
When the Erase Suspend command is written during a
sector erase operation, the device requires a maximum of
20μs to suspend the erase operation. However, when the
Erase Suspend command is written during the sector erase
time-out, the device immediately terminates the time-out
period and suspends the erase operation.
After the erase operation has been suspended, the system
can read array data from or program data to any sector not
selected for erasure. (The device "erase suspends" all
sectors selected for erasure.) Normal read and write timings
and command definitions apply. Reading at any address
within erase-suspended sectors produces status data on I/O7
- I/O0. The system can use I/O7, or I/O6 and I/O2 together, to
determine if a sector is actively erasing or is erasesuspended. See "Write Operation Status" for information on
these status bits.
After an erase-suspended program operation is complete,
the system can once again read array data within nonsuspended sectors. The system can determine the status of
the program operation using the I/O7 or I/O6 status bits, just
as in the standard program operation. See "Write Operation
Status" for more information.
The system may also write the autoselect command
sequence when the device is in the Erase Suspend mode.
The device allows reading autoselect codes even at
addresses within erasing sectors, since the codes are not
stored in the memory array. When the device exits the
autoselect mode, the device reverts to the Erase Suspend
mode, and is ready for another valid operation. See
"Autoselect Command Sequence" for more information.
(November, 2007, Version 1.1)
Data Poll
from System
Embedded
Erase
algorithm in
progress
No
Data = FFh ?
Yes
Erasure Completed
Note :
1. See the appropriate Command Definitions table for erase
command sequences.
2. See "I/O 3 : Sector Erase Timer" for more information.
Figure 4. Erase Operation
22
AMIC Technology, Corp.
A29L320A Series
Table 11. A29L320A Command Definitions
Autoselect (Note 8)
Manufacturer ID
Device ID,
Top Boot Block
Device ID,
Bottom Boot Block
Continuation ID
Sector Protect Verify
(Note 9)
Cycles
Command
Sequence
(Note 1)
Read (Note 6)
Reset (Note 7)
1
1
Word
Byte
Word
Byte
Word
Byte
Word
Byte
4
4
4
4
Word
Command Temporary
Sector Unprotect (Note9)
First
Addr Data
RA
RD
XXX F0
555
AA
AAA
555
AA
AAA
555
AA
AAA
555
AA
AAA
Second
Addr Data
Third
Fourth
Fifth
Addr Data Addr Data Addr Data
2AA
555
2AA
555
2AA
555
2AA
555
555
AAA
555
AAA
555
AAA
555
AAA
555
2AA
4
Byte
CFI Query (Note 10)
Bus Cycles (Notes 2 - 5)
AAA
Word
1
Byte
Word
Byte
3
Byte
4
Byte
Word
Unlock Bypass
3
Byte
Unlock Bypass Program (Note 2
11)
Unlock Bypass Reset (Note 12)
2
Word
Chip Erase
6
Byte
Word
Sector Erase
6
Byte
Erase Suspend (Note 13)
1
Erase Resume (Note 14)
1
Program
AA
55
AA
555
AAA
55
55
55
55
90
90
90
90
555
55
555
90
AAA
X00
Sixth
Addr Data
37
X01 22F6
X02 F6
X01 22F9
X02 F9
X03
7F
X06
(SA) XX00
X02 XX01
00
(SA)
X04
01
98
AA
2AA
555
55
555
AA
AAA
555
AA
AAA
XXX A0
2AA
555
2AA
555
PA
55
XXX 90
555
AA
AAA
555
AA
AAA
XXX B0
XXX 30
XXX
2AA
555
2AA
555
00
55
55
555
AAA
77
555
AAA
555
AAA
A0
555
AAA
555
AAA
80
PA
PD
555
AAA
555
AAA
AA
20
PD
55
80
AA
2AA
555
2AA
555
55
55
555
AAA
SA
10
30
Legend:
X = Don't care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE or CE pulse,
whichever happens later.
PD = Data to be programmed at location PA. Data latches on the rising edge of WE or CE pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits A20- A12 select a unique sector.
(November, 2007, Version 1.1)
23
AMIC Technology, Corp.
A29L320A Series
Note:
1. See Table 1 for description of bus operations.
2. All values are in hexadecimal.
3. Except when reading array or autoselect data, all bus cycles are write operation.
4. Address bits A20 - A11 are don't cares for unlock and command cycles, unless SA or PA required.
5. No unlock or command cycles required when reading array data.
6. The Reset command is required to return to reading array data when device is in the autoselect mode, or if I/O5 goes high
(while the device is providing status data).
7. The fourth cycle of the autoselect command sequence is a read cycle.
8. The data is 00h for an unprotected sector and 01h for a protected sector. See "Autoselect Command Sequence" for more
information.
9. Once a reset command is applied, software temporary unprotect is exit to return to read array data. But under erase
suspend condition, this command is still effective even a reset command has been applied. The reset command which can
deactivate the software temporary unprotect command is useful only after the erase command is complete.
10. Command is valid when device is ready to read array data or when device is in autoselect mode.
11. The Unlock Bypass command is required prior to the Unlock Bypass Program command.
12. The Unlock Bypass Reset command is required to return to reading array data when the device is in the unlock bypass
mode.
13. The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend mode.
14. The Erase Resume command is valid only during the Erase Suspend mode.
(November, 2007, Version 1.1)
24
AMIC Technology, Corp.
A29L320A Series
Write Operation Status
Several bits, I/O2, I/O3, I/O5, I/O6, I/O7, RY/ BY are provided in
the A29L320A to determine the status of a write operation.
Table 10 and the following subsections describe the
functions of these status bits. I/O7, I/O6 and RY/ BY each
offer a method for determining whether a program or erase
operation is complete or in progress. These three bits are
discussed first.
START
Read I/O7-I/O0
Address = VA
I/O7: Data Polling
The Data Polling bit, I/O7, indicates to the host system
whether an Embedded Algorithm is in progress or completed,
or whether the device is in Erase Suspend. Data Polling is
Yes
I/O7 = Data ?
valid after the rising edge of the final WE pulse in the
program or erase command sequence.
During the Embedded Program algorithm, the device outputs
on I/O7 the complement of the datum programmed to I/O7.
This I/O7 status also applies to programming during Erase
Suspend. When the Embedded Program algorithm is
complete, the device outputs the datum programmed to I/O7.
The system must provide the program address to read valid
status information on I/O7. If a program address falls within a
protected sector, Data Polling on I/O7 is active for
approximately 2μs, then the device returns to reading array
data.
During the Embedded Erase algorithm, Data Polling
produces a "0" on I/O7. When the Embedded Erase algorithm
is complete, or if the device enters the Erase Suspend mode,
Data Polling produces a "1" on I/O7.This is analogous to the
complement/true datum output described for the Embedded
Program algorithm: the erase function changes all the bits in
a sector to "1"; prior to this, the device outputs the
"complement," or "0." The system must provide an address
within any of the sectors selected for erasure to read valid
status information on I/O7.
After an erase command sequence is written, if all sectors
selected for erasing are protected, Data Polling on I/O7 is
active for approximately 100μs, then the device returns to
reading array data. If not all selected sectors are protected,
the Embedded Erase algorithm erases the unprotected
sectors, and ignores the selected sectors that are protected.
When the system detects I/O7 has changed from the
complement to true data, it can read valid data at I/O7 - I/O0
on the following read cycles. This is because I/O7 may
change asynchronously with I/O0 - I/O6 while Output Enable
( OE ) is asserted low. The Data Polling Timings (During
Embedded Algorithms) figure in the "AC Characteristics"
section illustrates this. Table 10 shows the outputs for Data
No
No
I/O5 = 1?
Yes
Read I/O7 - I/O0
Address = VA
Yes
I/O7 = Data ?
No
FAIL
Note :
1. VA = Valid address for programming. During a sector
erase operation, a valid address is an address within any
sector selected for erasure. During chip erase, a valid
address is any non-protected sector address.
2. I/O7 should be rechecked even if I/O5 = "1" because
I/O7 may change simultaneously with I/O5.
Polling on I/O7. Figure 5 shows the Data Polling algorithm.
(November, 2007, Version 1.1)
PASS
Figure 5. Data Polling Algorithm
25
AMIC Technology, Corp.
A29L320A Series
RY/ BY : Read/ Busy
I/O2: Toggle Bit II
The RY/ BY is a dedicated, open-drain output pin that
indicates whether an Embedded algorithm is in progress or
complete. The RY/ BY status is valid after the rising edge of
the final WE pulse in the command sequence. Since RY/ BY
is an open-drain output, several RY/ BY pins can be tied
together in parallel with a pull-up resistor to VCC.
If the output is low (Busy), the device is actively erasing or
programming. (This includes programming in the Erase
Suspend mode.) If the output is high (Ready), the device is
ready to read array data (including during the Erase Suspend
mode), or is in the standby mode.
Table 10 shows the outputs for RY/ BY . Refer to “ RESET
Timings”, “Timing Waveforms for Program Operation” and
“Timing Waveforms for Chip/Sector Erase Operation” for
more information.
I/O6: Toggle Bit I
Toggle Bit I on I/O6 indicates whether an Embedded Program
or Erase algorithm is in progress or complete, or whether the
device has entered the Erase Suspend mode. Toggle Bit I
may be read at any address, and is valid after the rising edge
of the final WE pulse in the command sequence (prior to the
program or erase operation), and during the sector erase
time-out.
During an Embedded Program or Erase algorithm operation,
successive read cycles to any address cause I/O6 to toggle.
(The system may use either OE or CE to control the read
cycles.) When the operation is complete, I/O6 stops toggling.
After an erase command sequence is written, if all sectors
selected for erasing are protected, I/O6 toggles for
approximately 100μs, then returns to reading array data. If not
all selected sectors are protected, the Embedded Erase
algorithm erases the unprotected sectors, and ignores the
selected sectors that are protected.
The system can use I/O6 and I/O2 together to determine
whether a sector is actively erasing or is erase-suspended.
When the device is actively erasing (that is, the Embedded
Erase algorithm is in progress), I/O6 toggles. When the device
enters the Erase Suspend mode, I/O6 stops toggling.
However, the system must also use I/O2 to determine which
sectors are erasing or erase-suspended. Alternatively, the
system can use I/O7 (see the subsection on " I/O7 : Data
Polling").
If a program address falls within a protected sector, I/O6
toggles for approximately 2μs after the program command
sequence is written, then returns to reading array data.
I/O6 also toggles during the erase-suspend-program mode,
and stops toggling once the Embedded Program algorithm is
complete.
The Write Operation Status table shows the outputs for
Toggle Bit I on I/O6. Refer to Figure 6 for the toggle bit
algorithm, and to the Toggle Bit Timings figure in the "AC
Characteristics" section for the timing diagram. The I/O2 vs.
I/O6 figure shows the differences between I/O2 and I/O6 in
graphical form. See also the subsection on " I/O2: Toggle Bit
II".
(November, 2007, Version 1.1)
26
The "Toggle Bit II" on I/O2, when used with I/O6, indicates
whether a particular sector is actively erasing (that is, the
Embedded Erase algorithm is in progress), or whether that
sector is erase-suspended. Toggle Bit II is valid after the
rising edge of the final WE pulse in the command sequence.
I/O2 toggles when the system reads at addresses within those
sectors that have been selected for erasure. (The system may
use either OE or CE to control the read cycles.) But I/O2
cannot distinguish whether the sector is actively erasing or is
erase-suspended. I/O6, by comparison, indicates whether the
device is actively erasing, or is in Erase Suspend, but cannot
distinguish which sectors are selected for erasure. Thus, both
status bits are required for sector and mode information.
Refer to Table 10 to compare outputs for I/O2 and I/O6.
Figure 6 shows the toggle bit algorithm in flowchart form, and
the section " I/O2: Toggle Bit II" explains the algorithm. See
also the " I/O6: Toggle Bit I" subsection. Refer to the Toggle
Bit Timings figure for the toggle bit timing diagram. The I/O2
vs. I/O6 figure shows the differences between I/O2 and I/O6 in
graphical form.
Reading Toggle Bits I/O6, I/O2
Refer to Figure 6 for the following discussion. Whenever the
system initially begins reading toggle bit status, it must read
I/O7 - I/O0 at least twice in a row to determine whether a
toggle bit is toggling. Typically, a system would note and store
the value of the toggle bit after the first read. After the second
read, the system would compare the new value of the toggle
bit with the first. If the toggle bit is not toggling, the device has
completed the program or erase operation. The system can
read array data on I/O7 - I/O0 on the following read cycle.
However, if after the initial two read cycles, the system
determines that the toggle bit is still toggling, the system also
should note whether the value of I/O5 is high (see the section
on I/O5). If it is, the system should then determine again
whether the toggle bit is toggling, since the toggle bit may
have stopped toggling just as I/O5 went high. If the toggle bit
is no longer toggling, the device has successfully completed
the program or erase operation. If it is still toggling, the device
did not complete the operation successfully, and the system
must write the reset command to return to reading array data.
The remaining scenario is that the system initially determines
that the toggle bit is toggling and I/O5 has not gone high. The
system may continue to monitor the toggle bit and I/O5
through successive read cycles, determining the status as
described in the previous paragraph. Alternatively, it may
choose to perform other system tasks. In this case, the
system must start at the beginning of the algorithm when it
returns to determine the status of the operation (top of Figure
6).
I/O5: Exceeded Timing Limits
I/O5 indicates whether the program or erase time has
exceeded a specified internal pulse count limit. Under these
conditions I/O5 produces a "1." This is a failure condition that
indicates the program or erase cycle was not successfully
completed.
AMIC Technology, Corp.
A29L320A Series
The I/O5 failure condition may appear if the system tries to
program a "1 "to a location that is previously programmed to
"0." Only an erase operation can change a "0" back to a "1."
Under this condition, the device halts the operation, and
when the operation has exceeded the timing limits, I/O5
produces a "1."
Under both these conditions, the system must issue the reset
command to return the device to reading array data.
START
Read I/O7-I/O0
I/O3: Sector Erase Timer
After writing a sector erase command sequence, the system
may read I/O3 to determine whether or not an erase
operation has begun. (The sector erase timer does not apply
to the chip erase command.) If additional sectors are
selected for erasure, the entire time-out also applies after
each additional sector erase command. When the time-out is
complete, I/O3 switches from "0" to "1." The system may
ignore I/O3 if the system can guarantee that the time
between additional sector erase commands will always be
less than 50μs. See also the "Sector Erase Command
Sequence" section.
After the sector erase command sequence is written, the
system should read the status on I/O7 ( Data Polling) or I/O6
(Toggle Bit 1) to ensure the device has accepted the
command sequence, and then read I/O3. If I/O3 is "1", the
internally controlled erase cycle has begun; all further
commands (other than Erase Suspend) are ignored until the
erase operation is complete. If I/O3 is "0", the device will
accept additional sector erase commands. To ensure the
command has been accepted, the system software should
check the status of I/O3 prior to and following each
subsequent sector erase command. If I/O3 is high on the
second status check, the last command might not have been
accepted. Table 10 shows the outputs for I/O3.
Read I/O7-I/O0
Toggle Bit
= Toggle ?
(Note 1)
No
Yes
No
I/O5 = 1?
Yes
Read I/O7 - I/O0
Twice
Toggle Bit
= Toggle ?
(Notes 1,2)
No
Yes
Program/Erase
Operation Not
Commplete, Write
Reset Command
Program/Erase
Operation Complete
Notes :
1. Read toggle bit twice to determine whether or not it is
toggling. See text.
2. Recheck toggle bit because it may stop toggling as I/O5
changes to "1". See text.
Figure 6. Toggle Bit Algorithm
(November, 2007, Version 1.1)
27
AMIC Technology, Corp.
A29L320A Series
Table 12. Write Operation Status
I/O7
Operation
I/O6
(Note 1)
Standard
Mode
Erase
Suspend
Mode
Embedded Program Algorithm
Embedded Erase Algorithm
Reading within Erase
Suspended Sector
Reading within Non-Erase
Suspend Sector
Erase-Suspend-Program
I/O5
I/O3
(Note 2)
I/O2
RY/ BY
(Note 1)
I/O7
Toggle
0
N/A
No toggle
0
0
Toggle
0
1
Toggle
0
1
No toggle
0
N/A
Toggle
1
Data
Data
Data
Data
Data
1
I/O7
Toggle
0
N/A
N/A
0
Notes:
1. I/O7 and I/O2 require a valid address when reading status information. Refer to the appropriate subsection for further details.
2. I/O5 switches to “1” when an Embedded Program or Embedded Erase operation has exceeded the maximum timing limits.
See “I/O5: Exceeded Timing Limits” for more information.
Maximum Negative Input Overshoot
20ns
20ns
+0.8V
-0.5V
-2.0V
20ns
Maximum Positive Input Overshoot
20ns
VCC+2.0V
VCC+0.5V
2.0V
20ns
(November, 2007, Version 1.1)
20ns
28
AMIC Technology, Corp.
A29L320A Series
DC Characteristics
CMOS Compatible
Parameter
Parameter Description
Symbol
ILI
Input Load Current
ILIT
ILO
A9 Input Load Current
Output Leakage Current
Test Description
Unit
VCC = VCC Max, A9 =12.5V
±1.0
35
μA
VOUT = VSS to VCC. VCC = VCC Max
±1.0
μA
VIN = VSS to VCC. VCC = VCC Max
ICC2
ICC3
VCC Active Write (Program/Erase)
Current (Notes 2, 3, 4)
VCC Standby Current (Note 2)
10
16
1 MHz
2
4
CE = VIL, OE = VIH
5 MHz
10
16
Word Mode
1 MHz
2
4
CE = VIL, OE =VIH
20
30
Ma
CE = RESET = VCC ± 0.3V
0.5
5
μA
RESET = VSS ± 0.3V
0.5
5
μA
VIH = VCC ± 0.3V; VIL = VSS ± 0.3V
0.5
5
μA
VIL
VCC Standby Current During Reset
(Note 2)
Automatic Sleep Mode
(Note 2, 4, 5)
Input Low Level
VIH
Input High Level
VHH
Voltage for WP /ACC Sector Protect/ VCC=3.0V ± 10%
Unprotect and Program Acceleration
Voltage for Autoselect and
VCC = 3.0 V ± 10%
Temporary Unprotect Sector
Output Low Voltage
IOL = 4.0mA, VCC = VCC Min
ICC4
ICC5
VID
VOL
VOH1
VOH2
Output High Voltage
μA
5 MHz
Byte Mode
ICC1
Typ.
Max.
CE = VIL, OE = VIH
VCC Active Read Current
(Notes 1, 2)
Min.
IOH = -2.0 mA, VCC = VCC Min
IOH = -100 μA, VCC = VCC Min
mA
-0.5
0.8
V
0.7 x VCC
VCC + 0.3
V
8.5
10.5
V
8.5
10.5
V
0.45
V
0.85 x VCC
VCC - 0.4
V
V
Notes:
1. The ICC current listed is typically less than 2 mA/MHz, with OE at VIH. Typical VCC is 3.3V.
2. Maximum ICC specifications are tested with VCC = VCC max.
3. ICC active while Embedded Algorithm (program or erase) is in progress.
4. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30ns. Typical sleep mode current
is 500nA.
5. Not 100% tested.
(November, 2007, Version 1.1)
29
AMIC Technology, Corp.
A29L320A Series
DC Characteristics (continued)
Zero Power Flash
Supply Current in mA
25
20
15
10
5
0
0
500
1000
1500
2000
2500
3000
3500
4000
Time in ns
Note: Addresses are switching at 1MHz
ICC1 Current vs. Time (Showing Active and Automatic Sleep Currents)
10
3.6V
8
Supply Current in mA
3.0V
6
4
2
0
1
2
3
4
5
Frequency in MHz
Note : T = 25 ° C
Typical ICC1 vs. Frequency
(November, 2007, Version 1.1)
30
AMIC Technology, Corp.
A29L320A Series
AC Characteristics
Read Only Operations
Description
Parameter
Symbols
JEDEC
Std
tAVAV
tRC
Read Cycle Time (Note 1)
tAVQV
tACC
Address to Output Delay
tELQV
tCE
Chip Enable to Output Delay
tGLQV
tOE
Output Enable to Output Delay
tOEH
Output Enable Hold
Time (Note 1)
Test Setup
Speed
Min.
Unit
-70
-80
-90
-120
70
80
90
120
ns
70
80
90
120
ns
CE = VIL
OE = VIL
Max.
OE = VIL
Max.
70
80
90
120
ns
Max.
30
30
40
50
ns
0
0
0
0
0
ns
10
10
10
10
10
ns
Max.
16
16
16
16
ns
16
16
16
16
ns
0
0
0
0
ns
Read
Toggle and
Data Polling
tEHQZ
tHZ
Chip Enable to Output High Z
(Notes 1)
tGHQZ
tDF
Output Enable to Output High Z
(Notes 1)
tAXQX
tOH
Output Hold Time from Addresses,
CE or OE , Whichever Occurs First
(Note 1)
Min.
Notes:
1. Not 100% tested.
2. See Test Conditions and Test Setup for test specifications.
Timing Waveforms for Read Only Operation
tRC
Addresses
Addresses Stable
tACC
CE
tDF
tOE
OE
tOEH
WE
tCE
tOH
High-Z
Output
Output Valid
High-Z
RESET
0V
RY/BY
(November, 2007, Version 1.1)
31
AMIC Technology, Corp.
A29L320A Series
AC Characteristics
Hardware Reset ( RESET )
Parameter
JEDEC
Std
Description
Test Setup
All Speed Options
Unit
tREADY
RESET Pin Low (During Embedded
Algorithms) to Read or Write (See Note)
Max
20
μs
tREADY
RESET Pin Low (Not During Embedded
Algorithms) to Read or Write (See Note)
Max
500
ns
tRP
RESET Pulse Width
Min
500
ns
tRH
RESET High Time Before Read (See Note)
Min
50
ns
tRB
RY/ BY Recovery Time
Min
0
ns
tRPD
RESET Low to Standby Mode
Min
20
μs
Note: Not 100% tested.
RESET Timings
RY/BY
CE, OE
tRH
RESET
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
~
~ ~
~
tReady
RY/BY
tRB
CE, OE
~
~
RESET
tRP
(November, 2007, Version 1.1)
32
AMIC Technology, Corp.
A29L320A Series
Temporary Sector Unprotect
Parameter
JEDEC
Std
tVIDR
Description
tRSP
tVHH
Unit
VID Rise and Fall Time (See Note)
Min
500
ns
RESET Setup Time for Temporary Sector
Unprotect
VHH Rise and Fall Time (See Note)
Min
4
μs
Min
250
ns
Min
4
μs
RESET Hold Time from RY/ BY High for
Temporary Sector/Sector Block Unprotect
tRRB
All Speed Options
Note: Not 100% tested.
Temporary Sector Unprotect Timing Diagram
VID
~
~
VID
VSS, VIL,
or VIH
VSS, VIL,
or VIH
RESET
tVIDR
tVIDR
Program or Erase Command Sequence
CE
~
~
WE
~ ~
~
~
tRSP
RY/BY
tRRB
Accelerated Program Timing Diagram
VCC
WP/ACC
~
~
VHH
VIL or VIH
VIL or VIH
tVHH
tVHH
AC Characteristics
Word/Byte Configuration ( BYTE )
Parameter
JEDEC
All Speed Options
Description
Std
-70
-80
-90
Unit
-120
CE to BYTE Switching Low or High
Max
tFLQZ
BYTE Switching Low to Output High-Z
Max
25
25
30
30
ns
tHQV
BYTE Switching High to Output Active
Min
70
80
90
120
ns
tELFL/tELFH
(November, 2007, Version 1.1)
33
ns
5
AMIC Technology, Corp.
A29L320A Series
BYTE Timings for Read Operations
CE
OE
BYTE
tELFL
BYTE
Switching
from word to
byte mode
Data Output
(I/O0-I/O14)
I/O0-I/O14
Data Output
(I/O0-I/O7)
I/O15
Output
I/O15 (A-1)
Address Input
tFLQZ
tELFH
BYTE
BYTE
Switching
from byte to
word mode
I/O0-I/O14
Data Output
(I/O0-I/O7)
I/O15 (A-1)
Address Input
Data Output
(I/O0-I/O14)
I/O15
Output
tFHQV
BYTE Timings for Write Operations
CE
The falling edge of the last WE signal
WE
BYTE
tSET
(tAS)
tHOLD(tAH)
Note:
Refer to the Erase/Program Operations table for tAS and tAH specifications.
(November, 2007, Version 1.1)
34
AMIC Technology, Corp.
A29L320A Series
AC Characteristics
Erase and Program Operations
Parameter
Speed
Description
JEDEC
Std
tAVAV
tWC
Write Cycle Time (Note 1)
tAVWL
tAS
tWLAX
Unit
-70
-80
-90
-120
Min.
70
80
90
120
ns
Address Setup Time
Min.
0
0
0
0
ns
tAH
Address Hold Time
Min.
40
45
45
50
ns
tDVWH
tDS
Data Setup Time
Min.
40
45
45
50
ns
tWHDX
tDH
Data Hold Time
Min.
0
ns
tOES
Output Enable Setup Time
Min.
0
ns
Read Recover Time Before Write
Min.
0
ns
tGHWL
tGHWL
( OE high to WE low)
tELWL
tCS
CE Setup Time
Min.
0
ns
tWHEH
tCH
CE Hold Time
Min.
0
ns
tWLWH
tWP
Write Pulse Width
Min.
tWHWL
tWPH
Write Pulse Width High
Min.
30
Byte
Typ.
6
tWHWH1
tWHWH1
Word
Typ.
9
Sector Erase Operation (Note 2)
Typ.
0.7
sec
tvcs
VCC Set Up Time (Note 1)
Min.
50
μs
tRB
Recovery Time from RY/ BY (Note 1)
Min
0
ns
Program/Erase Valid to RY/ BY Delay (Note 1)
Min
90
ns
tWHWH2
tWHWH2
tBUSY
Byte Programming Operation
(Note 2)
30
35
35
50
ns
ns
μs
Notes:
1. Not 100% tested.
2. See the "Erase and Programming Performance" section for more information.
(November, 2007, Version 1.1)
35
AMIC Technology, Corp.
A29L320A Series
Timing Waveforms for Program Operation
Program Command Sequence (last two cycles)
PA
555h
PA
tAH
PA
~
~ ~
~
Addresses
tAS
~
~
tWC
Read Status Data (last two cycles)
CE
~
~
tCH
OE
tWP
~
~
tWHWH1
WE
tCS
tWPH
A0h
Data
tDH
PD
~
~
tDS
Status
DOUT
tRB
tBUSY
~
~ ~
~
RY/BY
tVCS
VCC
Note :
1. PA = program addrss, PD = program data, Dout is the true data at the program address.
2. Illustration shows device in word mode.
(November, 2007, Version 1.1)
36
AMIC Technology, Corp.
A29L320A Series
Timing Waveforms for Chip/Sector Erase Operation
Erase Command Sequence (last two cycles)
tAS
~
~
tWC
SA
2AAh
VA
555h for chip erase
tAH
VA
~
~ ~
~
Addresses
Read Status Data
~
~
CE
OE
tCH
~
~
tWP
WE
tWPH
tWHWH2
tCS
tDH
55h
Data
30h
~
~
tDS
10h for chip erase
tBUSY
In
Progress
Complete
tRB
~
~
RY/BY
~
~
tVCS
VCC
Note :
1. SA = Sector Address (for Sector Erase), VA = Valid Address for reading status data (see "Write Operaion Ststus").
2. Illustratin shows device in word mode.
(November, 2007, Version 1.1)
37
AMIC Technology, Corp.
A29L320A Series
Timing Waveforms for Data Polling (During Embedded Algorithms)
~
~
tRC
Addresses
VA
tACC
CE
VA
~
~ ~
~
VA
tCE
tCH
~
~
tOE
OE
tDF
~
~
tOEH
WE
tOH
Status Data
~
~
Complement
Complement
True
Valid Data
~
~
High-Z
I/O7
Status Data
True
Valid Data
High-Z
I/O0 - I/O6
High-Z
tBUSY
~
~
RY/BY
Note : VA = Valid Address. Illustation shows first status cycle after command sequence, last status read cycle, and array data
read cycle.
(November, 2007, Version 1.1)
38
AMIC Technology, Corp.
A29L320A Series
Timing Waveforms for Toggle Bit (During Embedded Algorithms)
~
~
tRC
Addresses
VA
tACC
CE
VA
VA
~
~ ~
~
VA
tCE
tCH
tOE
~
~
OE
tDF
~
~
tOEH
WE
I/O6 , I/O2
High-Z
tBUSY
Valid Status
Valid Status
(first read)
(second read)
~
~
tOH
Valid Status
Valid Data
(stop togging)
~
~
RY/BY
Note: VA = Valid Address; not required for I/O6. Illustration shows first two status cycle after command sequence, last status
read cycle, and array data read cycle.
(November, 2007, Version 1.1)
39
AMIC Technology, Corp.
A29L320A Series
Timing Waveforms for Sector Protect/Unprotect
VID
VIH
~
~
RESET
SA, A6,
A1, A0
Valid*
Valid*
~
~
Valid*
Verify
~
~
Sector Protect/Unprotect
60h
60h
40h
Status
~
~
Data
Sector Protect:150us
Sector Unprotect:15ms
1us
CE
WE
OE
Note : For sector protect, A6=0, A1=1, A0=0. For sector unprotect, A6=1, A1=1, A0=0
Timing Waveforms for I/O2 vs. I/O6
~
~
Erase
Complete
~
~
~
~
Erase
~
~
~
~
~
~
Erase Suspend
Read
~
~
~
~
~
~
I/O2
~
~
I/O6
Erase
Suspend
Program
Erase Suspend
Read
~
~
Erase
Erase
Resume
~
~
WE
Enter Erase
Suspend Program
~
~
~
~
Erase
Suspend
~
~
Enter
Embedded
Erasing
I/O2 and I/O6 toggle with OE and CE
Note : Both I/O6 and I/O2 toggle with OE or CE. See the text on I/O6 and I/O2 in the section "Write Operation Status" for
more information.
(November, 2007, Version 1.1)
40
AMIC Technology, Corp.
A29L320A Series
Timing Waveforms for Alternate CE Controlled Write Operation
PA for program
SA for sector erase
555 for chip erase
Data Polling
~
~
555 for program
2AA for erase
PA
~
~
Addresses
tAS
tWH
tAH
~
~
tWC
~
~
WE
OE
tWHWH1 or 2
~
~
tCP
tBUSY
tCPH
CE
tWS
tDS
Data
tRH
A0 for program
55 for erase
PD for program
30 for sector erase
10 for chip erase
I/O7
DOUT
~
~
~
~
tDH
RESET
~
~
RY/BY
Note :
1. PA = Program Address, PD = Program Data, SA = Sector Address, I/O7 = Complement of Data Input, DOUT = Array Data.
2. Figure indicates the last two bus cycles of the command sequence.
Erase and Programming Performance
Parameter
Typ. (Note 1)
Unit
Sector Erase Time
0.7
sec
Chip Erase Time
45
sec
Byte Programming Time
6
μs
Word Programming Time
9
μs
Chip Programming Time
Byte Mode
32
sec
(Note 2)
Word Mode
20
sec
Comments
Excludes 00h programming prior to erasure
Excludes system-level overhead (Note 4)
Notes:
1. Typical program and erase times assume the following conditions: 25°C, 3.0V VCC, 100,000 cycles. Additionally,
programming typically assumes checkerboard pattern..
2. The typical chip programming time is considerably less than the maximum chip programming time listed, since most bytes
program faster than the maximum byte program time listed. If the maximum byte program time given is exceeded, only then
does the device set I/O5 = 1. See the section on I/O5 for further information.
3. In the pre-programming step of the Embedded Erase algorithm, all bytes are programmed to 00h before erasure.
4. System-level overhead is the time required to execute the four-bus-cycle command sequence for programming. See Table 9
for further information on command definitions.
5. The device has a guaranteed minimum erase and program cycle endurance of 100,000 cycles.
(November, 2007, Version 1.1)
41
AMIC Technology, Corp.
A29L320A Series
Latch-up Characteristics
Description
Min.
Max.
-1.0V
VCC+1.0V
-100 mA
+100 mA
-1.0V
12.5V
Input Voltage with respect to VSS on all I/O pins
VCC Current
Input voltage with respect to VSS on all pins except I/O pins
(including A9, OE and RESET )
Includes all pins except VCC. Test conditions: VCC = 5.0V, one pin at time.
TSOP/TFBGA Pin Capacitance
Parameter Symbol
CIN
COUT
CIN2
Parameter Description
Input Capacitance
Output Capacitance
Control Pin Capacitance
Test Setup
VIN=0
VOUT=0
VIN=0
TSOP
Typ.
Max.
6
7.5
Unit
pF
TFBGA
4.2
5
pF
TSOP
8.5
12
pF
TFBGA
5.4
6.5
pF
TSOP
7.5
9
pF
TFBGA
3.9
4.7
pF
Notes:
1. Sampled, not 100% tested.
2. Test conditions TA = 25°C, f = 1.0MHz
Data Retention
Parameter
Test Conditions
Min
Unit
150°C
10
Years
125°C
20
Years
Minimum Pattern Data Retention Time
(November, 2007, Version 1.1)
42
AMIC Technology, Corp.
A29L320A Series
Test Conditions
Test Specifications
Test Condition
-70
-80
Output Load
-90
-120
Unit
100
pF
1 TTL gate
Output Load Capacitance, CL(including jig capacitance)
30
100
Input Rise and Fall Times
100
5
Input Pulse Levels
ns
0.0 – VCC
V
Input timing measurement reference levels
0.5VCC
V
Output timing measurement reference levels
0.5VCC
V
Test Setup
3.0V
2.7 KW
Device
Under
Test
CL
6.2 KW
Diodes = IN3064 or Equivalent
Input Waveforms and Measurement Levels
VCC
Input
0.5VCC
Measurement Level
0.5VCC
Output
0.0V
(November, 2007, Version 1.1)
43
AMIC Technology, Corp.
A29L320A Series
Ordering Information
Top Boot Sector Flash
Part No.
Access Time
(ns)
Active Read
Current
Typ. (mA)
Program/Erase
Current
Typ. (mA)
Standby Current
Typ. (μA)
Package
A29L320ATV-70
48Pin TSOP
A29L320ATV-70U
48Pin TSOP
A29L320ATV-70I
48Pin TSOP
A29L320ATV-70F
48 Pin Pb-Free TSOP
A29L320ATV-70UF
48 Pin Pb-Free TSOP
A29L320ATV-70IF
48 Pin Pb-Free TSOP
70
10
20
0.5
A29L320ATG-70
48 ball TFBGA
A29L320ATG-70U
48 ball TFBGA
A29L320ATG-70I
48 ball TFBGA
A29L320ATG-70F
48 ball Pb-Free TFBGA
A29L320ATG-70UF
48 ball Pb-Free TFBGA
A29L320ATG-70IF
48 ball Pb-Free TFBGA
A29L320ATV-80
48Pin TSOP
A29L320ATV-80U
48Pin TSOP
A29L320ATV-80I
48Pin TSOP
A29L320ATV-80F
48Pin Pb-Free TSOP
A29L320ATV-80UF
48Pin Pb-Free TSOP
A29L320ATV-80IF
48Pin Pb-Free TSOP
80
10
20
0.5
A29L320ATG-80
48 ball TFBGA
A29L320ATG-80U
48 ball TFBGA
A29L320ATG-80I
48 ball TFBGA
A29L320ATG-80F
48 ball Pb-Free TFBGA
A29L320ATG-80UF
48 ball Pb-Free TFBGA
A29L320ATG-80IF
48 ball Pb-Free TFBGA
Note: -U is for industrial operating temperature range: -40°C to +85°C
-I is for industrial operating temperature range: -25°C to +85°C
(November, 2007, Version 1.1)
44
AMIC Technology, Corp.
A29L320A Series
Ordering Information (continued)
Top Boot Sector Flash
Part No.
Access Time
(ns)
Active Read
Current
Typ. (mA)
Program/Erase
Current
Typ. (mA)
Standby Current
Typ. (μA)
Package
A29L320ATV-90
48Pin TSOP
A29L320ATV-90U
48Pin TSOP
A29L320ATV-90I
48Pin TSOP
A29L320ATV-90F
48Pin Pb-Free TSOP
A29L320ATV-90UF
48Pin Pb-Free TSOP
A29L320ATV-90IF
48Pin Pb-Free TSOP
90
10
20
0.5
A29L320ATG-90
48 ball TFBGA
A29L320ATG-90U
48 ball TFBGA
A29L320ATG-90I
48 ball TFBGA
A29L320ATG-90F
48 ball Pb-Free TFBGA
A29L320ATG-90UF
48 ball Pb-Free TFBGA
A29L320ATG-90IF
48 ball Pb-Free TFBGA
A29L320ATV-120
48Pin TSOP
A29L320ATV-120U
48Pin TSOP
A29L320ATV-120I
48Pin TSOP
A29L320ATV-120F
48Pin Pb-Free TSOP
A29L320ATV-120UF
48Pin Pb-Free TSOP
A29L320ATV-120IF
48Pin Pb-Free TSOP
120
10
20
0.5
A29L320ATG-120
48 ball TFBGA
A29L320ATG-120U
48 ball TFBGA
A29L320ATG-120I
48 ball TFBGA
A29L320ATG-120F
48 ball Pb-Free TFBGA
A29L320ATG-120UF
48 ball Pb-Free TFBGA
A29L320ATG-120IF
48 ball Pb-Free TFBGA
Note: -U is for industrial operating temperature range: -40°C to +85°C
-I is for industrial operating temperature range: -25°C to +85°C
(November, 2007, Version 1.1)
45
AMIC Technology, Corp.
A29L320A Series
Ordering Information (continued)
Bottom Boot Sector Flash
Part No.
Access Time
(ns)
Active Read
Current
Typ. (mA)
Program/Erase
Current
Typ. (mA)
Standby Current
Typ. (μA)
Package
A29L320AUV-70
48Pin TSOP
A29L320AUV-70U
48Pin TSOP
A29L320AUV-70I
48Pin TSOP
A29L320AUV-70F
48 Pin Pb-Free TSOP
A29L320AUV-70UF
48 Pin Pb-Free TSOP
A29L320AUV-70IF
48 Pin Pb-Free TSOP
70
10
20
0.5
A29L320AUG-70
48 ball TFBGA
A29L320AUG-70U
48 ball TFBGA
A29L320AUG-70I
48 ball TFBGA
A29L320AUG-70F
48 ball Pb-Free TFBGA
A29L320AUG-70UF
48 ball Pb-Free TFBGA
A29L320AUG-70IF
48 ball Pb-Free TFBGA
A29L320AUV-80
48Pin TSOP
A29L320AUV-80U
48Pin TSOP
A29L320AUV-80I
48Pin TSOP
A29L320AUV-80F
48Pin Pb-Free TSOP
A29L320AUV-80UF
48Pin Pb-Free TSOP
A29L320AUV-80IF
48Pin Pb-Free TSOP
80
10
20
0.5
A29L320AUG-80
48 ball TFBGA
A29L320AUG-80U
48 ball TFBGA
A29L320AUG-80I
48 ball TFBGA
A29L320AUG-80F
48 ball Pb-Free TFBGA
A29L320AUG-80UF
48 ball Pb-Free TFBGA
A29L320AUG-80IF
48 ball Pb-Free TFBGA
Note: -U is for industrial operating temperature range: -40°C to +85°C
-I is for industrial operating temperature range: -25°C to +85°C
(November, 2007, Version 1.1)
46
AMIC Technology, Corp.
A29L320A Series
Ordering Information (continued)
Bottom Boot Sector Flash
Part No.
Access Time
(ns)
Active Read
Current
Typ. (mA)
Program/Erase
Current
Typ. (mA)
Standby Current
Typ. (μA)
Package
A29L320AUV-90
48Pin TSOP
A29L320AUV-90U
48Pin TSOP
A29L320AUV-90I
48Pin TSOP
A29L320AUV-90F
48Pin Pb-Free TSOP
A29L320AUV-90UF
48Pin Pb-Free TSOP
A29L320AUV-90IF
48Pin Pb-Free TSOP
90
10
20
0.5
A29L320AUG-90
48 ball TFBGA
A29L320AUG-90U
48 ball TFBGA
A29L320AUG-90I
48 ball TFBGA
A29L320AUG-90F
48 ball Pb-Free TFBGA
A29L320AUG-90UF
48 ball Pb-Free TFBGA
A29L320AUG-90IF
48 ball Pb-Free TFBGA
A29L320AUV-120
48Pin TSOP
A29L320AUV-120U
48Pin TSOP
A29L320AUV-120I
48Pin TSOP
A29L320AUV-120F
48Pin Pb-Free TSOP
A29L320AUV-120UF
48Pin Pb-Free TSOP
A29L320AUV-120IF
48Pin Pb-Free TSOP
120
10
20
0.5
A29L320AUG-120
48 ball TFBGA
A29L320AUG-120U
48 ball TFBGA
A29L320AUG-120I
48 ball TFBGA
A29L320AUG-120F
48 ball Pb-Free TFBGA
A29L320AUG-120UF
48 ball Pb-Free TFBGA
A29L320AUG-120IF
48 ball Pb-Free TFBGA
Note: -U is for industrial operating temperature range: -40°C to +85°C
-I is for industrial operating temperature range: -25°C to +85°C
(November, 2007, Version 1.1)
47
AMIC Technology, Corp.
A29L320A Series
Package Information
TSOP 48L (Type I) Outline Dimensions
unit: inches/mm
1
48
24
25
y
D1
A1
A2 A
D
0.25
c
S
e
E
b
D
Detail "A"
L
θ
Detail "A"
Symbol
Dimensions in inches
Dimensions in mm
Min
Nom
Max
Min
Nom
Max
A
-
-
0.047
-
-
1.20
A1
0.002
-
0.006
0.05
-
0.15
A2
0.037
0.039
0.042
0.94
1.00
1.06
b
0.007
0.009
0.011
0.18
0.22
0.27
c
0.004
-
0.008
0.12
-
0.20
D
0.779
0.787
0.795
19.80
20.00
20.20
D1
0.720
0.724
0.728
18.30
18.40
18.50
E
-
0.472
0.476
-
12.00
12.10
e
L
0.020 BASIC
0.020
S
0.024
0.50 BASIC
0.0275
0.50
0.011 Typ.
0.60
0.70
0.28 Typ.
y
-
-
0.004
-
-
0.10
θ
0°
-
8°
0°
-
8°
Notes:
1. The maximum value of dimension D includes end flash.
2. Dimension E does not include resin fins.
3. Dimension S includes end flash.
(November, 2007, Version 1.1)
48
AMIC Technology, Corp.
A29L320A Series
Package Information
48LD CSP (6 x 8 mm) Outline Dimensions
unit: mm
(48TFBGA)
BOTTOM VIEW
TOP VIEW
b
3
2
1
1
H
H
G
G
F
F
E
E
D
D
C
C
B
B
A
A
2
3
4
5
6
E
4
E1
5
e
6
e
D1
Ball*A1 CORNER
D
A
SIDE VIEW
SEATING PLANE
A1
C
0.10 C
Symbol
A
A1
b
D
D1
e
E
E1
(November, 2007, Version 1.1)
Dimensions in mm
Min.
0.20
0.30
5.90
Nom.
0.25
6.00
4.00 BSC
0.80
7.90
8.00
5.60 BSC
49
Max.
1.20
0.30
0.40
6.10
8.10
AMIC Technology, Corp.