AWS5532R 0.5 to 2.5 GHz 10 W SPDT Switch PRELIMINARY DATA SHEET - Rev 1.3 FEATURES • Low Insertion Loss: 0.4 dB at 2 GHz • High Isolation: >25 dB • High Input P0.1 dB: +40.5 dBm • Low Control Voltage Operation • Low Profile Surface Mount Package • RoHS Compliant Package, 260 oC MSL-1 AW S 553 2R APPLICATIONS • Automotive Telematic Applications • GSM Wireless Handsets and Front-end Modules • CDMA Wireless Handsets and Front-end Modules S26 Package 12 Pin 3 mm x 3 mm x 1 mm QFN PRODUCT DESCRIPTION to provide low insertion loss, high port-to-port isolation, and high linearity performance. The AWS5532R is offered in a 12-lead 3 mm x 3 mm x 1 mm QFN package. The AWS5532R is a single pole, double throw (SPDT) RF switch developed for applications requiring very low distortion at high input drive levels. Manufactured in ANADIGICS’s state-of-the-art pHEMT process, the device uses patented circuit topologies NC RFC VS 12 11 10 NC 1 9 NC RF1 2 8 RF2 GND 3 7 GND 4 5 6 V1 NC V2 Figure 1: Block Diagram 09/2005 AWS5532R NC RFC VS 12 11 10 NC 1 9 NC RF1 2 8 RF2 GND 3 7 GND 4 5 V1 NC 6 V2 Figure 2: Pinout (X-ray Top View) Table 1: Pin Description PIN NAME DESCRIPTION 2 RF1 RF Port, Path 1 4 V1 Control Voltage, RF Path 1 6 V2 Control Voltage, RF Path 2 8 RF2 RF Port, Path 2 10 VS Common Port Bias Voltage (logic high) 11 RFC RF Common Port 3,7 GND Ground 1, 5, 9, 12 NC No Connection (1) Notes: (1) Pins 1, 5, 9 and 12 are not connected in the package. Recommend pins be grounded, but is not necessary. 2 PRELIMINARY DATA SHEET - Rev 1.3 09/2005 AWS5532R ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Control Voltages (V1, V2, VS) (1) - +10.0 V RF Input Power (PIN) (2) - 15 W -65 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Notes: (1) VS port may remain open without damage to the device. (2) at RF1, RF2, and RFC Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT RF Frequency (f) 0.5 - 2.5 GHz - (1) - - applied at VS port (Pin 10) Control Voltages (V1, V2) -0.2 +2.5 - +0.2 +5 V RF path OFF state RF path ON state Ambient Temperature (TA) -40 - +85 Common Port Bias Voltage (Vs) o COMMENTS C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) The Common Port Bias Voltage (Vs) is not required for normal operation, and can be left open. To operate the switch in an “all off” state (both V1 and V2 set to logic LOW), the logic HIGH voltage should be applied to this port. Under no circumstances should this port be grounded. PRELIMINARY DATA SHEET - Rev 1.3 09/2005 3 AWS5532R Table 4: ESD Ratings PARAMETER METHOD RATING ESD Threshold Voltage (All Pins) CDM (1) 1000 ESD Threshold Voltage (Supply pins only) HBM (3) 400 (2) (4) UNIT V V ESD Threshold Voltage (Supply-Signal pins) HBM 400 V ESD Threshold Voltage (RF Signal pins only) HBM 450 V ESD Threshold Voltage (Antenna Common Port) HBM (5) 12000 (6) V Notes: (1) Tested in conformance with JEDEC specification JESD22-C101-A (2) A CDM ESD threshold of this voltage classifies the device as a Class IV component per JEDEC JESD22-C101-A (3) Tested in conformance with ESD/EOS Society specification STM5.1-2001 (4) A HBM ESD threshold at these voltages classifies the device as a Class 1A component per ESD/EOS Society Specification STM5.1-2001 (5) This test was done in conformance with ESD/EOS Society HBM specification STM5.1-2001. 3000 ESD strikes were applied using multiple groups of 100 strikes each where the interval between strikes within a group is 1 second and the interval between groups is 30 seconds. (6) This voltage rating REQUIRES the use of an inductor as an RF choke as defined in Note #3 in the application circuit information. This rating has been tested with inductor values of 47nH and 100nH. 4 PRELIMINARY DATA SHEET - Rev 1.3 09/2005 AWS5532R Table 5: Electrical Specifications (TA = +25 OC, RF ports terminated with 50 Ω, Vn = +3.0 V and is the Control Voltage for the ON path, RFCRFn; VX = 0 V and is the Control Voltage for the other OFF path, RFC-RFx) PARAMETER MIN TYP MAX UNIT COMMENTS Insertion Loss 1 GHz 2 GHz - 0.30 0.40 0.5 0.6 dB RFC port to selected RFn port Return Loss 1 GHz 2 GHz - 24 22 20 18 dB RFC port and selected RFn port Isolation 1 GHz 2 GHz 27 25 30 27 - dB RFC port to isolated RFx port Input Third Order Intercept (2) 824 - 849 MHz +68 +71 - dB m RFC port to selected RFn port Input Power for 0.1 dB Compression 824 - 849 MHz +39 +40.5 - dB m Current Consumption - - 50 mA (1) each Vn port Notes: (1) Isolated RFx ports have a return loss of approximately -3 dB. (2) Two tones with PIN = +27 dBm each, 1 MHz channel spacing. Table 6: Switch Control Truth Table CONTROL VOLTAGE RF PATH SELECTION V1 V2 R FC - R F1 R FC - R F2 +2.5 to +5 V -0.2 to +0.2 V ON OFF -0.2 to +0.2 V +2.5 to +5 V OFF ON PRELIMINARY DATA SHEET - Rev 1.3 09/2005 5 AWS5532R PERFORMANCE DATA Figure 4: Insertion Loss vs. Temperature (Vn = 3.0 V, F = 836 MHz) 0 0 -0.2 -0.2 Insertion Loss (dB) Insertion Loss (dB) Figure 3: Insertion Loss vs. Frequency (ON Path, Vn = +3.0 V, Vx = 0 V) -0.4 -0.6 -0.8 -0.4 -0.6 T=-40 C T=+25 C T=+85 C -0.8 -1 500 -1 1000 1500 2000 2500 30 31 32 33 34 Frequency (MHz) 35 36 37 38 39 40 41 Input Power (dBm) Figure 5: Return Loss vs. Frequency (ON Path, Vn = +3.0 V, Vx = 0 V) Figure 6: Compression vs. Temperature (Vn = 3.0 V, F = 836 MHz) 0 0.1 -5 RFn Port Gain Compression (dB) 0 Return Loss (dB) RFC Port -10 -15 -20 -0.1 T=-40 C -0.2 T=+25 C T=+85 C -0.3 -25 -30 500 -0.4 1000 1500 2000 30 2500 31 32 33 34 35 36 37 38 39 40 41 Input Power (dBm) Frequency (MHz) Figure 7: Isolation vs. Frequency (OFF Path, Vn = +3.0 V, Vx = 0 V) Figure 8: Compression vs. VCONTROL (VS = Vn, F = 836 MHz) 0 0.1 0 Gain Compression (dB) Isolation (dB) -10 -20 -0.1 -0.2 Vc=2.5 V Vc=2.6 V Vc=2.7 V Vc=2.8 V Vc=2.9 V Vc=3.0 V -30 -0.3 -40 500 -0.4 1000 1500 2000 2500 30 31 32 6 33 34 35 36 Input Power (dBm) Frequency (MHz) PRELIMINARY DATA SHEET - Rev 1.3 09/2005 37 38 39 40 41 AWS5532R APPLICATION INFORMATION Circuit Applications External component requirements for the AWS5532R are shown in Figure 9. Application details are listed in the following notes: 1. Cb are DC blocking capacitors external to the device. A value of 100 pF is sufficient for operation to 500 MHz. The values may be tailored to provide specific electrical responses. 2. The RF Ground connections should be kept as short as possible and tied directly to a good RF ground for best broadband performance. attached to the antenna. By using LESD as an RF choke on an RF port, an ESD protection to ±12 kV contact discharge has been demonstrated. 4. The VS pin provides a fixed voltage potential to the common port of the switch, and is not required for normal operation (can be left open). To operate the switch in an “all off” state (V1 = V2 = logic low), VS should be tied to the logic high voltage potential (not the power supply). Current draw on this pin is less than 5 mA. 3. L ESD provides a means to increase the ESD protection on a specific RF port, typically the port Common (Ant.) RF Port LESD Cb NC Common Port Supply NC VS Note 4 (Open or Logic High) RFC Note 3 12 11 10 1 NC 9 Cb Cb RF Gnd, Path 1 Shunt 2 8 3 7 4 5 6 NC V2 RF1 V1 RF Port 1 Control Pin, RF Path 1 RF Port 2 RF2 RF Gnd, Path 2 Shunt Keep RF Gnd Connection Short 2 Places, Note 2 Control Pin, RF Path 2 Figure 9: Application Schematic PRELIMINARY DATA SHEET - Rev 1.3 09/2005 7 AWS5532R PACKAGE OUTLINE Figure 10: S26 Package Outline - 12 Pin 3 mm x 3 mm x 1 mm QFN 8 PRELIMINARY DATA SHEET - Rev 1.3 09/2005 AWS5532R COMPONENT PACKAGING Figure 11: Tape & Reel Packaging Square Module / MLF User Direction of Feed Figure 12: Tape & Reel Package Orientation Table 7: Tape & Reel Dimensions PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 3 mm x 3 mm x 1 mm 12 mm 8 mm 1000 7" PRELIMINARY DATA SHEET - Rev 1.3 09/2005 9 AWS5532R NOTES 10 PRELIMINARY DATA SHEET - Rev 1.3 09/2005 AWS5532R NOTES PRELIMINARY DATA SHEET - Rev 1.3 09/2005 11 AWS5532R ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING AWS5532RS26Q1 -40 oC to +85 oC RoHS Compliant 12 Pin QFN 3 mm x 3 mm x 1 mm Tape and Reel, 1000 pieces per Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 12 PRELIMINARY DATA SHEET - Rev 1.3 09/2005