AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications General Description Features The AAT3134 is a low noise, constant frequency charge pump DC/DC converter that uses a dual mode load switch (1X) and fractional (1.5X) conversion to maximize efficiency for white LED applications. The device can be used to produce current levels up to 20mA in each of its six outputs to drive LEDs from a 2.7V to 5.5V input. Outputs may be operated individually or paralleled for driving higher-current LEDs. A low external parts count (two 1µF flying capacitors and two small 1µF capacitors at VIN and OUT) make the AAT3134 ideally suited for small battery-powered applications. • • • • • • • • • • • • • • • AnalogicTech's Simple Serial Control™ (S2Cwire™) interface is used to enable, disable, and set the LED drive current in two groups of four outputs and two outputs with multiple-level, independently-controlled brightness scales. The AAT3134 has a thermal management system to protect the device in the event of a short-circuit condition at the output pin. Built-in soft-start circuitry prevents excessive inrush current during start-up. A high charge pump switching frequency enables the use of very small external capacitors. A low-current shutdown feature disconnects the load from VIN and reduces quiescent current to less than 1µA. The AAT3134 is available in a Pb-free 16-pin QFN44 package and is rated over the -40°C to +85°C temperature range. ChargePump™ VIN Range: 2.7V to 5.5V <1.0µA of Shutdown 1MHz Switching Frequency Fully Independent Display Lighting Dual Mode 1X and 1.5X Charge Pump for Maximum Efficiency Drives Low-VF and High-VF Type LEDs Up to Six 20mA Outputs Multi-Position Brightness Scale with Digital Control Low Noise Constant Frequency Operation Small Application Circuit Regulated Output Current Automatic Soft Start No Inductors 16-Pin QFN44 Package -40°C to +85°C Temperature Range Applications • • • • Color (RGB) Lighting Programmable Current Source White LED Backlighting White LED Photo Flash for Digital Still Cameras Typical Application VIN C1+ C1 1µF VOUT VBATTERY CIN 1µF EN/SET COUT 1µF C1C2+ AAT3134 EN/SET C2 1µF C2D1 D2 D3 D4 D5 D6 D4 D3 D2 D1 GND D6 D5 Sub Display 3134.2005.12.1.1 Main Display 1 AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications Pin Descriptions Pin # Symbol Function 1 2 3 4 5 6 7 8,13 9 10 11 12 14 15 16 EP D2 D5 D6 D3 D4 C1+ C1N/C OUT C2+ C2GND IN EN/SET D1 Current source output #2. Current source output #5. Current source output #6. Current source output #3. Current source output #4. Flying capacitor 1 positive terminal. Connect a 1µF capacitor between C1+ and C1-. Flying capacitor 1 negative terminal. No connection. Charge pump output. Requires 1µF capacitor connected between this pin and ground. Flying capacitor 2 positive terminal. Connect a 1µF capacitor between C2+ and C2-. Flying capacitor 2 negative terminal. Ground. Input power supply. Requires 1µF capacitor connected between this pin and ground. Control pin. Current source output #1. Exposed paddle (bottom); connect to GND directly beneath package. Pin Configuration QFN44-16 (Top View) 15 13 16 14 EN/SET 1 12 GND D5 2 11 C2- D6 3 10 C2+ D3 4 9 OUT 8 7 6 5 N/C C1- C1+ D4 2 N/C IN D1 D2 3134.2005.12.1.1 AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications Absolute Maximum Ratings1 Symbol VIN VOUT FB, VEN/SET VEN/SET(MAX) IOUT2 TJ Description Input Voltage Charge Pump Output FB or EN/SET to GND Voltage Maximum EN/SET to Input Voltage Maximum DC Output Current Operating Junction Temperature Range Value Units -0.3 to 6.0 -0.3 to 6.0 -0.3 to 6.0 0.3 150 -40 to 150 V V V V mA °C Value Units Thermal Information3 Symbol θJA θJC PD Description Thermal Resistance Thermal Resistance Maximum Power Dissipation 50 15 2 °C/W W 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Based on long-term current density limitation. 3. Mounted on an FR4 board. 3134.2005.12.1.1 3 AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications Electrical Characteristics1 VIN = 3.5V, CIN = COUT = C1 = C2 = 1.0µF; TA = -40°C to +85°C. Unless otherwise noted, typical values are TA = 25°C. Symbol Description Conditions Input Power Supply VIN Operation Range ICC Operating Current ISHDN IDX(MAX) Shutdown Current Maximum Output Current Current Matching Between I(D-Match) Any Two Outputs Charge Pump Section TSS Soft-Start Time FCLK Clock Frequency ηCP EN/SET VEN(L) VEN(H) TEN/SET LO TEN/SET HI TOFF Input Current Charge Pump Section Efficiency Enable Threshold Low Enable Threshold High EN/SET Low Time Minimum EN/SET High Time EN/SET Off Timeout EN/SET Input Leakage Min Typ 2.7 3.0 ≤ VIN ≤ 5.5, Active, No Load Current EN/SET = 0 VIN = 3.6, Code = 32 VD1:D4 = 3.6, VIN = 3.5V VD5:VD6 = 3.6, VIN = 3.5V 1.8 18 VIN = 3.5V, IOUT(TOTAL) = 120mA, Measured from IN to OUT 20 0.5 0.5 Max Units 5.5 V 3.5 mA 1.0 22 µA mA % 200 1000 µs kHz 93 % 0.5 VEN/SET < 0.5 VEN/SET > 1.4 VEN/SET < 0.5 1.4 0.3 75 50 -1.0 500 1.0 V V µs ns µs µA 1. The AAT3134 is guaranteed to meet performance specifications over the -40°C to +85°C operating temperature range and is assured by design, characterization, and correlation with statistical process controls. 4 3134.2005.12.1.1 AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications Typical Characteristics Unless otherwise noted, VIN = 3.5V, CIN = COUT = C1 = C2 = 1µF, TA = 25°C. Efficiency vs. Input Voltage IDIODE vs. Input Voltage (4x20mA) (4x20mA) 100 90 VDIODE = 3.3V 85 90 VDIODE = 3.3V 80 85 VDIODE = 3.4V 75 IDIODE (mA) Efficiency (%) 95 80 75 VDIODE = 3.5V 70 65 VDIODE = 3.6V 60 VDIODE = 3.4V 70 65 60 55 50 55 45 50 40 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 2.7 5.1 2.9 3.1 3.3 3.5 Input Voltage (V) 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 2.50 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 Input Voltage (V) Quiescent Current vs. Input Voltage Quiescent Current (mA) VDIODE = 3.5V VDIODE = 3.6V VIH and VIL vs. VIN 0.850 0.825 0.800 0.775 VIH 0.750 VDIODE = 3.3V 0.725 VDIODE = 3.4V 0.700 VDIODE = 3.5V 0.675 VDIODE = 3.6V 0.650 VIL 0.625 0.600 3.00 3.50 4.00 4.50 Input Voltage (V) 3134.2005.12.1.1 5.00 5.50 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Input Voltage (V) 5 AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications Typical Characteristics Unless otherwise noted, VIN = 3.5V, CIN = COUT = C1 = C2 = 1µF, TA = 25°C. Turn-On to Full-Scale Charge Pump Turn-On to Full-Scale Load Switch ENSET (1V/div) ENSET (1V/div) OUT (2V/div) OUT (2V/div) VDIODE (1V/div) VDIODE (2V/div) IIN (200mA/div) IIN (100mA/div) Time (50µs/div) Time (50µs/div) Charge Pump to Load Switch Load Switch to Charge Pump (80mA) (80mA) VIN (10mV/div) VIN (20mV/div) OUT (2V/div) OUT (1V/div) VDIODE (2V/div) VDIODE (1V/div) IIN (100mA/div) IIN (200mV/div) Time (50µs/div) Time (50µs/div) Turn-Off 80mA Load Characteristics VIN 20mV/div ENSET (1V/div) VDIODE (2V/div) OUT IIN (100mA/div) VDIODE Time (200µs/div) 6 Time (1µs/div) 3134.2005.12.1.1 AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications Functional Block Diagram VIN Soft-Start Control C1+ C11X/1.5X Charge Pump 1MHz Oscillator Voltage Reference C2+ C2OUT D1 Current Reference Quad Output DAC D2 D3 D4 32x16 bit ROM EN/SET S2Cwire Interface Dual Output DAC 32x16 bit ROM D5 D6 GND Functional Description The AAT3134 is a dual mode load switch (1X) and high efficiency (1.5X) fractional charge pump device intended for white LED backlight applications. The fractional charge pump consists of a low dropout linear voltage regulator followed by a 1.5X charge pump with multiple current source outputs. To maximize power conversion efficiency, an internal feedback control sensing circuit monitors the voltage required on the constant current source outputs. This control circuit then sets the load switch and charge pump functions based upon the input voltage level versus the output voltage level needed. This function significantly enhances overall device efficiency when the input voltage level is greater than the voltage required at the constant current source outputs. The 1X load switch/1.5X charge pump mode decision is based on the voltage levels sensed on either the D1 or D5 output, whichever is greater. Switchover between the 1.5X (charge pump) operating mode and the 1X (load switch) mode occurs 3134.2005.12.1.1 automatically (as a function of input and output voltages) and does not require user intervention to maintain maximum efficiency. The AAT3134 requires only four external components: two 1µF ceramic capacitors for the charge pump flying capacitors (C1 and C2), one 1µF ceramic input capacitor (CIN), and one 0.33µF to 1µF ceramic output capacitor (COUT). The LDO/1.5X charge pump output is converted into four (D1 to D4) constant current outputs to drive four individual LEDs with a maximum current of 20mA each and two (D5 and D6) constant current outputs with a maximum current of 20mA. The current source output magnitude is controlled by the EN/SET serial data interface. The interface records rising edges of the EN/SET pin and decodes them into 32 addresses corresponding to individual current level settings. The 32 addresses are divided up such that outputs D1 to D4 can be controlled independently of outputs D5 to D6. For Addresses 1 to 6, 7 to 12, 13 to 18, 19 to 24, and 25 to 30, outputs D1 to D4 start at 0mA and increase from 1mA to 20mA in four steps. Outputs D5 and D6 7 AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications remain constant over these address ranges which provides orthogonal control of the two channels. For Addresses 1 to 6, D5 and D6 are set to 0mA, Addresses 7 to 12 are 1mA; Addresses 13 to 18 are 10mA; Addresses 19 to 24 are 12mA; and Addresses 25 to 30 are 15mA. For maximum brightness control, Addresses 31 and 32 set D5 and D6 to the maximum 20mA level. For design flexibility, D1 to D4 are set to 0mA at Address 31, and 20mA at Address 32. This is summarized in Table 1 and Figure 1. Applications Information Constant Current Output Level Settings The constant current source output amplitude for output D1 to D4 and D5 to D6 are set via the serial interface according to the scale described in Figure 1 and the previous section. Because the outputs D1 to D6 are true independent constant current sources, the voltage observed on any single given output will be determined by the actual forward voltage (VF) for the LED being driven. The modulo 32 interface wraps back to State 1 after the 32nd clock. With each EN/SET pulse, the output current changes to the next setting in the address decoding. To change settings to the previous address decoding, 31 EN/SET clock pulses are required. The counter can be clocked at speeds up to 1MHz, so that intermediate states are not visible. The first rising edge of EN/SET enables the IC and initially sets the output LED currents to 0mA. Additional clocks are required to set the desired current level. Once the final clock cycle is input for the desired brightness level, the EN/SET pin is held high to maintain the device output current at the programmed level. The device is disabled 500µs after the EN/SET pin transitions to a logic low state. Since the output current of the AAT3134 is programmable through the S2Cwire serial interface, no PWM (pulse width modulation) or additional control circuitry are needed to control LED brightness. This feature greatly reduces the burden on a microcontroller or system IC to manage LED or display brightness, allowing the user to "set it and forget it." Furthermore, with its high-speed serial interface (1MHz data rate), the output current of the AAT3134 can be changed successively to brighten or dim LEDs in smooth transitions (e.g., to fade out) or in abrupt steps, giving the user complete programmability and real-time control of LED brightness. 20 18 Current (mA) 16 14 12 10 8 6 4 2 0 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Address Code Figure 1: Output Current Level Settings. 8 3134.2005.12.1.1 AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications Address 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Current Level Settings (mA) D1 to D4 D5 to D6 0 1 10 12 15 20 0 1 10 12 15 20 0 1 10 12 15 20 0 1 10 12 15 20 0 1 10 12 15 20 0 20 0 0 0 0 0 0 1 1 1 1 1 1 10 10 10 10 10 10 12 12 12 12 12 12 15 15 15 15 15 15 20 20 EN/SET Serial Interface The current source output magnitude is controlled by the EN/SET serial interface. The interface records rising edges of the EN/SET pin and decodes them into 32 individual current level settings, as summarized in Table 1. The modulo 32 interface wraps back to State 1 after the 32nd clock, so that the previous state is achieved by clocking the EN/SET pin 31 times. The counter can be clocked at speeds up to 1MHz, so that intermediate states are not visible. The first rising edge of EN/SET enables the IC and initially sets the output LED current to 0. Once the final clock cycle is input for the desired brightness level, the EN/SET pin is held high to maintain the device output current at the programmed level. The device is disabled 500µs after the EN/SET pin transitions to a logic low state. The EN/SET timing is designed to accommodate a wide range of data rates. After the first rising edge of EN/SET, the charge pump is enabled and reaches full capacity after the softstart time (TSS). During the soft-start time, multiple clock pulses may be entered on the EN/SET pin to set the final output current level with a single burst of clocks. Alternatively, the EN/SET clock pulses may be entered one at a time to gradually increase the LED brightness over any desired time period. A constant current is sourced as long as EN/SET remains in a logic high state. The current source outputs are switched off after EN/SET has remained in a low state for at least the TOFF timeout period. Table 1: Constant Current Source Output Programming Levels. 3134.2005.12.1.1 9 AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications EN/SET Timing Diagram tHI tOFF tLO EN/SET Code OFF 1 LED Selection The AAT3134 is specifically intended for driving white LEDs. However, the device design will allow the AAT3134 to drive most types of LEDs with forward voltage specifications ranging from 2.0V to 4.3V. LED applications may include main and subLCD display backlighting, camera photo-flash applications, color (RGB) LEDs, infrared (IR) diodes for remotes, and other loads benefiting from a controlled output current generated from a varying input voltage. Since the D1 to D6 output current sources are matched with negligible voltage dependence, the LED brightness will be matched regardless of the specific LED forward voltage (VF) levels. In some instances (e.g., in high luminous output applications such as photo flash), it may be necessary to drive high-VF type LEDs. The low dropout current sources in the AAT3134 make it capable of driving LEDs with forward voltages as high as 4.3V at full current from an input supply as low as 3.0V. Outputs can be paralleled to drive high-current LEDs without complication. Device Switching Noise Performance The AAT3134 operates at a fixed frequency of approximately 1MHz to control noise and limit harmonics that can interfere with the RF operation of cellular telephone handsets or other communication devices. Back-injected noise appearing on the input pin of the charge pump is 20mV peak-to-peak, typ- 10 2 3 OFF ically ten times less than inductor-based DC/DC boost converter white LED backlight solutions. The AAT3134 soft-start feature prevents noise transient effects associated with inrush currents during startup of the charge pump circuit. Power Efficiency and Device Evaluation The charge pump efficiency discussion in the following sections only accounts for efficiency of the charge pump section itself. Due to the unique circuit architecture and design of the AAT3134, it is very difficult to measure efficiency in terms of a percent value comparing input power over output power. Since the AAT3134 outputs are pure constant current sources and typically drive individual loads, it is difficult to measure the output voltage for a given output (D1 to D6) to derive an overall output power measurement. For any given application, white LED forward voltage levels can differ, yet the output drive current will be maintained as a constant. This makes quantifying output power a difficult task when taken in the context of comparing to other white LED driver circuit topologies. A better way to quantify total device efficiency is to observe the total input power to the device for a given LED current drive level. The best white LED driver for a given application should be based on trade-offs of size, external components count, reliability, operating range, and total energy usage...not just % efficiency. 3134.2005.12.1.1 AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications The AAT3134 efficiency may be quantified under very specific conditions and is dependent upon the input voltage versus the output voltage seen across the loads applied to outputs D1 through D6 for a given constant current setting. Depending upon VIN being greater than the specific voltage seen across the load on D1 (or D6), the device will operate in load switch mode. If VIN is less than the voltage required on the constant current source, the device will operate in 1.5X charge pump mode. Each of these two modes will yield different efficiency values. One should refer to the following two sections for explanations for each operational mode. half times the input voltage. Efficiency (η) for an ideal 1.5X charge pump can typically be expressed as the output power divided by the input power: η= In addition, with an ideal 1.5X charge pump, the output current may be expressed as 2/3 of the input current. The expression to define the ideal efficiency (η) can be rewritten as: η= Load Switch Mode Efficiency The AAT3134 load switch mode is operational at all times and functions alone to enhance device power conversion efficiency when the condition exists where VIN is greater than voltage across the load connected to the constant current source outputs. When in load switch mode, the voltage conversion efficiency is defined as output power divided by input power: η= POUT PIN The expression to define the ideal efficiency (η) can be rewritten as: η= POUT VOUT × IOUT VOUT = = PIN VIN × IOUT VIN -or- POUT PIN POUT VOUT × IOUT VOUT = = PIN VIN × 1.5IOUT 1.5VIN -or- η(%) = 100 ⎛ VOUT ⎞ ⎝ 1.5VIN⎠ For a charge pump with an output of 5V and a nominal input of 3.5V, the theoretical efficiency is 95%. Due to internal switching losses and IC quiescent current consumption, the actual efficiency can be measured at 93%. These figures are in close agreement for output load conditions from 1mA to 100mA. Efficiency will decrease as load current drops below 0.05mA or when the level of VIN approaches VOUT. Refer to the Typical Characteristics section of this document for measured plots of efficiency versus input voltage and output load current for the given charge pump output voltage options. Capacitor Selection ⎛ VOUT ⎞ η(%) = 100 ⎝ VIN ⎠ Charge Pump Section Efficiency The AAT3134 contains a fractional charge pump which will boost the input supply voltage when VIN is less than the voltage required on the constant current source outputs. The efficiency (η) can be simply defined as a linear voltage regulator with an effective output voltage that is equal to one and one 3134.2005.12.1.1 Careful selection of the four external capacitors CIN, C1, C2, and COUT is important because they will affect turn-on time, output ripple, and transient performance. Optimum performance will be obtained when low equivalent series resistance (ESR) ceramic capacitors are used. In general, low ESR may be defined as less than 100mΩ. A value of 1µF for all four capacitors is a good starting point when choosing capacitors. If the LED current sources are only programmed for light current levels, then the capacitor size may be decreased. 11 AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications Capacitor Characteristics Ceramic Capacitor Materials Ceramic composition capacitors are highly recommended over all other types of capacitors for use with the AAT3134. Ceramic capacitors offer many advantages over their tantalum and aluminum electrolytic counterparts. A ceramic capacitor has very low ESR, is lowest cost, has a smaller PCB footprint, and is non-polarized. Low ESR ceramic capacitors help to maximize charge pump transient response. Since ceramic capacitors are non-polarized, they are not prone to incorrect connection damage. Ceramic capacitors less than 0.1µF are typically made from NPO or C0G materials. NPO and C0G materials have tight tolerance and are stable over temperature. Large capacitor values are typically composed of X7R, X5R, Z5U, or Y5V dielectric materials. Large ceramic capacitors, greater than 2.2µF, are often available in low-cost Y5V and Z5U dielectrics, but capacitors greater than 1µF are usually not required for AAT3134 applications. Capacitor area is another contributor to ESR. Capacitors that are physically large will have a lower ESR when compared to an equivalent material smaller capacitor. These larger devices can improve circuit transient response when compared to an equal value capacitor in a smaller package size. Equivalent Series Resistance ESR is an important characteristic to consider when selecting a capacitor. ESR is a resistance internal to a capacitor that is caused by the leads, internal connections, size or area, material composition, and ambient temperature. Capacitor ESR is typically measured in milliohms for ceramic capacitors and can range to more than several ohms for tantalum or aluminum electrolytic capacitors. VIN Thermal Protection The AAT3134 has a thermal protection circuit that will shut down the internal LDO and charge pump if the die temperature rises above the thermal limit, as is the case during a short-circuit of the OUT pin. C1+ C1 1µF CIN C OUT 1µF 1µF D2 D3 D4 RB* RB* R B* RB* C1C2+ VOUT VBATTERY D1 AAT3134 C2 1µF C2- EN/SET EN/SET Resistor R is optional D1 D2 D3 D4 D5 D6 D5 D6 GND R R Resistor R is optional *In some applications, white LED forward voltages (VF) can vary significantly. Ballast resistors between the LED cathodes and ground are recommended for balancing the forward voltage differences. The ballast resistor value may be approximated by the following equation: RB = VSOURCE - VF IF Figure 2: AAT3134 Driving Two Groups of Paralleled White LEDs (e.g., main and sub-LCD backlights). 12 3134.2005.12.1.1 AAT3134 High Efficiency 1X/1.5X Fractional Charge Pump for White LED Applications Ordering Information Package Marking1 Part Number (Tape and Reel)2 QFN44-16 JBXYY AAT3134ISN-T1 All AnalogicTech products are offered in Pb-free packaging. The term “Pb-free” means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/pbfree. Package Information 0.330 ± 0.050 Pin 1 Identification 13 16 0.650 BSC 1 R0.030Max 4 9 8 4.000 ± 0.050 2.400 ± 0.050 5 2.280 REF Top View 0.0125 ± 0.0125 Bottom View 0.203 ± 0.025 0.900 ± 0.050 4.000 ± 0.050 Pin 1 Dot By Marking 0.450 ± 0.050 0.600 ± 0.050 QFN44-16 Side View All dimensions in millimeters. 1. XYY = assembly and date code. 2. Sample stock is generally held on part numbers listed in BOLD. © Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. AnalogicTech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with AnalogicTech’s standard warranty. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. Advanced Analogic Technologies, Inc. 830 E. Arques Avenue, Sunnyvale, CA 94085 Phone (408) 737-4600 Fax (408) 737-4611 3134.2005.12.1.1 13