ARTESYN PTH05010WADT

PTH05010
5 Vin single output
DC-DC CONVERTERS
•
•
•
•
•
•
•
•
•
•
•
POLA Non-isolated
1
NEW Product
15 A output current
5 V input voltage
Wide-output voltage adjust (0.8 Vdc to 3.6 Vdc)
Auto-track™ sequencing*
Margin up/down controls
Pre-bias start-up capability
Efficiencies up to 95%
Output ON/OFF inhibit
Output voltage sense
Point-of-Load-Alliance (POLA) compatible
Available RoHS compliant
The PTH05010 is a next generation series of non-isolated dc-dc converters offering some
of the most advanced POL features available in the industry. The primary new feature
provides for sequencing between multiple modules, a function, which is becoming a
necessity for powering advanced silicon including DSP’s, FPGA’s and ASIC’s requiring
controlled power-up and power-down Other industry leading features include margin
up/down controls, pre-bias start-up capability and efficiencies up to 95%. The
PTH05010 has an input voltage of 4.5 Vdc to 5.5 Vdc and offers a wide 0.8 Vdc to 3.6 Vdc
output voltage range with up to 15 A output current, which allows for maximum design
flexibility and a pathway for future upgrades.
2 YEAR WARRANTY
All specifications are typical at nominal input, full load at 25 °C unless otherwise stated
Cin = 470 µF, Cout = 0 µF
OUTPUT SPECIFICATIONS
Voltage adjustability
EMC CHARACTERISTICS
(See Note 4)
Setpoint accuracy
0.8-3.6 Vdc
±2.0% Vo
Line regulation
±10 mV typ.
Load regulation
±12 mV typ.
Total regulation
±3.0% Vo
Minimum load
Ripple and noise
0A
20 MHz bandwidth
Temperature co-efficient -40 ºC to +85 ºC
Transient response
(See Note 5)
30 mV pk-pk
±0.5% Vo
70 µs recovery time
Overshoot/undershoot 100 mV
Margin adjustment
±5.0% Vo
Electrostatic discharge
Conducted immunity
Radiated immunity
EN61000-4-2, IEC801-2
EN61000-4-6
EN61000-4-3
GENERAL SPECIFICATIONS
Efficiency
(See Efficiency Table)
Insulation voltage
Switching frequency
275 kHz to 325 kHz
Approvals and
standards
EN60950
UL/cUL60950
Material flammability
Dimensions
Input voltage range
(See Note 3)
Input current
No load
Remote ON/OFF
(See Note 1)
4.5-5.5 Vdc
10 mA typ.
Positive logic
Start-up time
1 V/ms
Undervoltage lockout
3.7-4.3 V typ.
Pin 8 (See Note 6, 7)
MTBF
95% max.
Non-isolated
UL94V-0
(L x W x H)
34.80 x 15.75 x 9.00 mm
1.370 x 0.620 x 0.354 in
Weight
INPUT SPECIFICATIONS
Track input voltage
SPECIFICATIONS
5 g (0.18 oz)
Telcordia SR-332
7,092,000 hours
ENVIRONMENTAL SPECIFICATIONS
Thermal performance
(See Note 2)
MSL (‘Z’ suffix only)
Operating ambient,
temperature
Non-operating
JEDEC J-STD-020C
-40 ºC to +85 ºC
-40 ºC to +125 ºC
Level 3
±0.3 Vin
PROTECTION
International Safety Standard Approvals
UL/cUL CAN/CSA-C22.2 No. 60950-1-03/UL 60950-1,
File No. E174104
TÜV Product Service (EN60950) Certificate No. B 04 06 38572 044
CB Report and Certificate to IEC60950, Certificate No.
US/8292/UL
Short-circuit
Auto reset
Thermal
27.5 A typ.
Auto recovery
*Auto-track™ is a trade mark of
Texas Instruments
File Name: pth05010.pdf Rev (06): 16 Dec 2005
PTH05010
5 Vin single output
DC-DC CONVERTERS
POLA Non-isolated
2
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
OUTPUT
POWER
(MAX.)
INPUT
VOLTAGE
54 W
4.5-5.5 Vdc
OUTPUT
VOLTAGE
0.8-3.6 Vdc
Part Number System with Options
NEW Product
OUTPUT
CURRENT
(MIN.)
OUTPUT
CURRENT
(MAX.)
EFFICIENCY
(MAX.)
LINE
LOAD
MODEL
NUMBER (9,10)
0A
15 A
95%
±10 mV
±12 mV
PTH05010
REGULATION
PTH05010WAST
Product Family
Point of Load Alliance
Compatible
Input Voltage
05 = 5 V
Output Current
01 = 15 A
Mechanical Package
Always 0
Packaging Options
No Suffix = Trays
T = Tape and Reel (8)
Mounting Option (9)
D = Horizontal Through-Hole (Matte Sn)
H = Horizontal Through-Hole (Sn/Pb)
S = Surface-Mount (63/37 Sn/Pb
pin solder material)
Z = Surface-Mount (96.5/3.0/0.5 Sn/Ag/Cu
pin solder material)
Pin Option
A = Through-Hole Std. Pin Length (0.140”)
A = Surface-Mount Tin/Lead Solder Ball
Output Voltage Code
W = Wide
Output Voltage Adjustment of the PTH05010 Series
The ultra-wide output voltage trim range offers major advantages to users who
select the PTH05010. It is no longer necessary to purchase a variety of
modules in order to cover different output voltages. The output voltage can be
trimmed in a range of 0.8 Vdc to 3.6 Vdc. When the PTH05010 converter
leaves the factory the output has been adjusted to the default voltage of 0.8 V.
Notes
1
Remote ON/OFF. Positive Logic
ON:
Pin 3 open; or V > Vin - 0.5 V
OFF:
Pin 3 GND; or V < 0.8 V (min - 0.2 V).
2 See Figures 1 and 2 for safe operating curves.
3 A 470 µF electrolytic input capacitor is required for proper operation. The
capacitor must be rated for a minimum of 700 mA rms of ripple current.
4 An external output capacitor is not required for basic operation. Adding
33 0µF of distributed capacitance at the load will improve the transient
response.
5 1 A/µs load step, 50 to 100% Iomax, Cout = 330 µF.
6 If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point).
7 The pre-bias start-up feature is not compatible with Auto-Track™. This is
because when the module is under Auto-Track™ control, it is fully active
and will sink current if the output voltage is below that of a back-feeding
source. Therefore to ensure a pre-bias hold-off, one of the following two
techniques must be followed when input power is first applied to the
module. The Auto-Track™ function must either be disabled, or the
module’s output held off using the Inhibit pin. Refer to Application Note
155 for more details.
8 Tape and reel packaging only available on the surface-mount versions.
9 To order Pb-free (RoHS compatible) surface-mount parts replace the
mounting option ‘S’ with ‘Z’, e.g. PTH05010WAZ. To order Pb-free
(RoHS compatible) through-hole parts replace the mounting option ‘H’
with ‘D’, e.g. PTH05010WAD.
10 NOTICE: Some models do not support all options. Please contact your
local Artesyn representative or use the on-line model number search tool at
http://www.artesyn.com/powergroup/products.htm to find a suitable
alternative.
EFFICIENCY TABLE (IO = 10 A)
OUTPUT VOLTAGE
EFFICIENCY
Vo = 1.0 V
86%
Vo = 1.2 V
88%
Vo = 1.5 V
90%
Vo = 1.8 V
91%
Vo = 2.0 V
92%
Vo = 2.5 V
93%
Vo = 3.3 V
95%
File Name: pth05010.pdf Rev (06): 16 Dec 2005
PTH05010
5 Vin single output
DC-DC CONVERTERS
POLA Non-isolated
3
90
90
80
80
70
60
Nat conv
100 LFM
200 LFM
400 LFM
50
40
30
TEMPERATURE (ºC)
TEMPERATURE (ºC)
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
20
NEW Product
70
60
Nat conv
100 LFM
200 LFM
400 LFM
50
40
30
20
0
2
4
6
8
10
0
14
12
2
OUTPUT CURRENT (A)
4
6
8
10
14
12
OUTPUT CURRENT (A)
Figure 2 - Safe Operating Area
Vin = 5 V, Output Voltage = 1.0 V (See Note A)
Figure 1 - Safe Operating Area
Vin = 5 V, Output Voltage = 3.3 V (See Note A)
Track
Margin Down
Margin Up
Vo Adjust
EFFICIENCY (%)
100
Vout
3.3V
2.5V
2.0V
1.8V
1.5V
1.2V
1.0V
0.8V
90
80
70
60
10
Vin
4
6
8
10
12
7
Vout
6
2
3
Inhibit
+
2
8
PTH05010
(Top View)
50
0
9
1
Cin 470µF
(Required)
4
5
Vo Sense
RSET 1%, 0.1W
(Required)
+
Cout 330µF
(Optional)
L
O
A
D
14
GND
GND
OUTPUT CURRENT (A)
Figure 3 - Efficiency vs Load Current
Vin = 5 V (See Note B)
Figure 4 - Standard Application
Notes
A SOA curves represent the conditions at which internal components are
within the Artesyn derating guidelines.
B Characteristic data has been developed from actual products tested at
25 °C. This data is considered typical data for the converter.
File Name: pth05010.pdf Rev (06): 16 Dec 2005
PTH05010
5 Vin single output
DC-DC CONVERTERS
POLA Non-isolated
4
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
1.370 (34.80)
0.060
(1.52)
0.125 (3.18)
0.125 (3.18)
0.375
(9.52)
1
0.140
(3.55)
0.060
(1.52)
0.625 (15.88)
8
9
10
ø0.040 (1.02)
5 Places
7
0.070 (1.78)
(Standoff Shoulder)
0.620
0.500 (15.75)
(12.70)
2
Lowest Component
0.010 min. (0.25)
Bottom side Clearance
6
5
4
3
NEW Product
PIN CONNECTIONS
PIN NO.
FUNCTION
1
Ground
2
Vin
TOP VIEW
Host Board
Dimensions in Inches (mm)
Tolerances (unless otherwise specified)
2 Places ±0.030 (±0.76)
3 Places ±0.010 (±0.25)
3
Inhibit*
0.354 (9.00)
MAX.
4
Vo adjust
SIDE VIEW
5
Vo sense
6
Vout
7
Ground
8
Track
9
Margin down*
10
Margin up*
Figure 5 - Plated Through-Hole Mechanical Drawing
*Denotes negative logic:
Open = Normal operation
Ground = Function active
1.370 (34.80)
0.060
(1.52)
0.125 (3.18)
0.125 (3.18)
0.375
(9.52)
1
10
0.060
(1.52)
0.625 (15.88)
9
8
0.354 (9.00)
max.*
7
*After solder reflow
on customer board
Solder Ball
ø0.040 (1.02)
10 Places
0.500 0.620
(12.70) (15.75)
Lowest Component
0.010 min. (0.25)
Bottom side Clearance
2
3
5
4
6
TOP VIEW
SIDE VIEW
Host Board
Dimensions in Inches (mm)
Tolerances (unless otherwise specified)
2 Places ±0.030 (±0.76)
3 Places ±0.010 (±0.25)
Figure 6 - Surface-Mount Mechanical Drawing
Datasheet © Artesyn Technologies® 2005
The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising
from printing errors or inaccuracies. The information and specifications contained or described herein are subject to change in any manner at any time without notice. No rights under any patent
accompany the sale of any such product(s) or information contained herein.
Please consult our website for the following items: Application Note
www.artesyn.com
File Name: pth05010.pdf Rev (06): 16 Dec 2005