ARIZONA MICROTEK, INC. AZ10EL11 AZ100EL11 ECL/PECL 1:2 Differential Fanout Buffer FEATURES • • • • • • PACKAGE AVAILABILITY RoHS Compliant / Lead (Pb) Free Packages available 265ps Propagation Delay 5ps Skew Between Outputs High Bandwidth Output Transitions 75kΩ Internal Input Pulldown Resistors Direct Replacement for ON Semiconductor MC10EL11 & MC100EL11 PACKAGE MARKING NOTES 1,2 1,2 SOIC 8 AZ10EL11D AZM10 EL11 SOIC 8 RoHS Compliant / Lead (Pb) Free AZ10EL11D+ AZM10+ EL11 SOIC 8 AZ100EL11D TSSOP 8 AZ10EL11T TSSOP 8 AZ100LVEL11T 1 2 DESCRIPTION PART NUMBER AZM100 EL11 AZT EL11 AZH EL11 1,2 1,2 1,2 Add R1 at end of part number for 7 inch (1K parts), R2 for 13 inch (2.5K parts) Tape & Reel. Date code format: “Y” or “YY” for year followed by “WW” for week on underside of part. The AZ10/100EL11 is a differential 1:2 fanout gate. The device is functionally similar to the E111 device but with higher performance capabilities. Having within-device skews and output transition times significantly improved over the E111, the EL11 is ideally suited for those applications that require the ultimate in AC performance. The differential inputs of the EL11 employ clamping circuitry to maintain stability under open input conditions. If the inputs are left open (pulled to VEE) the Q outputs will go LOW. NOTE: Specifications in the ECL/PECL tables are valid when thermal equilibrium is established. LOGIC DIAGRAM AND PINOUT ASSIGNMENT Q0 1 8 VCC Q0 2 7 D Q1 3 6 D Q1 4 5 VEE PIN DESCRIPTION PIN D, D ¯ Q0, Q0 ¯¯ , Q1, Q1 ¯¯ VCC VEE FUNCTION Data Inputs Data Outputs Positive Supply Negative Supply 1630 S. STAPLEY DR., SUITE 127 • MESA, ARIZONA 85204 • USA • (480) 962-5881 • FAX (480) 890-2541 www.azmicrotek.com AZ10EL11 AZ100EL11 Absolute Maximum Ratings are those values beyond which device life may be impaired. Symbol VCC VI VEE VI IOUT TA TSTG Characteristic PECL Power Supply (VEE = 0V) PECL Input Voltage (VEE = 0V) ECL Power Supply (VCC = 0V) ECL Input Voltage (VCC = 0V) Output Current --- Continuous --- Surge Operating Temperature Range Storage Temperature Range Rating 0 to +8.0 0 to +6.0 -8.0 to 0 -6.0 to 0 50 100 -40 to +85 -65 to +150 Unit Vdc Vdc Vdc Vdc mA °C °C 10K ECL DC Characteristics (VEE = -4.75V to -5.5V, VCC = GND) Symbol Characteristic 1 Min -1080 -1950 -1230 -1950 -40°C Typ Max -890 -1650 -890 -1500 150 VOH Output HIGH Voltage VOL Output LOW Voltage1 VIH Input HIGH Voltage VIL Input LOW Voltage Input HIGH Current IIH Input LOW Current 0.5 IIL IEE Power Supply Current 26 31 1. Each output is terminated through a 50Ω resistor to VCC – 2V. Min -1020 -1950 -1170 -1950 0°C Typ Max -840 -1630 -840 -1480 150 0.5 Min -980 -1950 -1130 -1950 25°C Typ Max -810 -1630 -810 -1480 150 0.5 26 31 Min -910 -1950 -1060 -1950 85°C Typ Max -720 -1595 -720 -1445 150 0.5 26 31 26 31 Unit mV mV mV mV μA μA mA 10K PECL DC Characteristics (VEE = GND, VCC = +5.0V) Symbol Characteristic 1,2 Min 3920 3050 3770 3050 -40°C Typ Max 4110 3350 4110 3500 150 Min 3980 3050 3830 3050 0°C Typ Max 4160 3370 4160 3520 150 Min 4020 3050 3870 3050 VOH Output HIGH Voltage VOL Output LOW Voltage1,2 VIH Input HIGH Voltage1 VIL Input LOW Voltage1 IIH Input HIGH Current Input LOW Current 0.5 0.5 0.5 IIL IEE Power Supply Current 26 31 26 31 1. For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. 2. Each output is terminated through a 50Ω resistor to VCC – 2V. 25°C Typ Max 4190 3370 4190 3520 150 Min 4090 3050 3940 3050 85°C Typ Max 4280 3405 4280 3555 150 0.5 26 31 26 31 Unit mV mV mV mV μA μA mA 100K ECL DC Characteristics (VEE = -4.2V to -5.5V, VCC = GND) Symbol Characteristic 1 Min -1085 -1830 -1165 -1810 -40°C Typ -1005 -1695 Max -880 -1555 -880 -1475 150 VOH Output HIGH Voltage VOL Output LOW Voltage1 VIH Input HIGH Voltage VIL Input LOW Voltage Input HIGH Current IIH Input LOW Current 0.5 IIL IEE Power Supply Current 26 31 1. Each output is terminated through a 50Ω resistor to VCC – 2V. Min -1025 -1810 -1165 -1810 0°C Typ -955 -1705 Max -880 -1620 -880 -1475 150 0.5 Min -1025 -1810 -1165 -1810 25°C Typ -955 -1705 Max -880 -1620 -880 -1475 150 0.5 26 31 Min -1025 -1810 -1165 -1810 85°C Typ -955 -1705 Max -880 -1620 -880 -1475 150 0.5 26 31 30 36 Unit mV mV mV mV μA μA mA 100K PECL DC Characteristics (VEE = GND, VCC = +5.0V) Symbol Characteristic 1,2 Min 3915 3170 3835 3190 -40°C Typ 3995 3305 Max 4120 3445 4120 3525 150 Min 3975 3190 3835 3190 0°C Typ 4045 3295 Max 4120 3380 4120 3525 150 Min 3975 3190 3835 3190 VOH Output HIGH Voltage VOL Output LOW Voltage1,2 VIH Input HIGH Voltage1 VIL Input LOW Voltage1 IIH Input HIGH Current Input LOW Current 0.5 0.5 0.5 IIL IEE Power Supply Current 26 31 26 31 1. For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value. 2. Each output is terminated through a 50Ω resistor to VCC – 2V. November 2006 * REV - 4 www.azmicrotek.com 2 25°C Typ 4045 3295 Max 4120 3380 4120 3525 150 Min 3975 3190 3835 3190 85°C Typ 4045 3295 Max 4120 3380 4120 3525 150 0.5 26 31 30 36 Unit mV mV mV mV μA μA mA AZ10EL11 AZ100EL11 AC Characteristics (VEE =10E(-4.75V to -5.5V), 100E(-4.2V to -5.5V); VCC =GND or VEE =GND; VCC =10E(+4.75V to +5.5V), 100E(+4.2V to +5.5V)) Symbol Characteristic VPP (AC) Propagation Delay to Output Within-Device Skew1 Duty Cycle Skew2 Minimum Input Swing3 VCMR Common Mode Range4 tPLH / tPHL tSKEW tr / t f 1. 2. 3. 4. Min -40°C Typ Max Min 0°C Typ Max Min 25°C Typ Max Min 85°C Typ Max 135 260 385 185 260 335 190 265 340 215 290 365 5 5 20 20 5 5 20 20 5 5 20 20 5 5 150 VCC 2.0 VCC 0.4 150 VCC 2.0 VCC 0.4 150 VCC 2.0 VCC 0.4 150 VCC 2.0 www.azmicrotek.com 3 ps ps mV VCC 0.4 Rise/Fall Time 100 350 100 350 100 350 100 350 20 – 80% Within-device skew defined as identical transitions on similar paths through a device. Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device. VPP is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed. The device has a DC voltage gain of ≈ 40. The VCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPP(min) and 1V. November 2006 * REV - 4 Unit V ps AZ10EL11 AZ100EL11 PACKAGE DIAGRAM SOIC 8 NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm. November 2006 * REV - 4 DIM A A1 A2 A3 bp c D E e HE L Lp Q v w y Z θ www.azmicrotek.com 4 MILLIMETERS MIN MAX 1.75 0.10 0.25 1.25 1.45 0.25 0.36 0.49 0.19 0.25 4.8 5.0 3.8 4.0 1.27 5.80 6.20 1.05 0.40 1.00 0.60 0.70 0.25 0.25 0.10 0.30 0.70 8O 0O INCHES MIN MAX 0.069 0.004 0.010 0.049 0.057 0.01 0.014 0.019 0.0075 0.0100 0.19 0.20 0.15 0.16 0.050 0.228 0.244 0.041 0.016 0.039 0.024 0.028 0.01 0.01 0.004 0.012 0.028 0O 8O AZ10EL11 AZ100EL11 PACKAGE DIAGRAM TSSOP 8 DIM A A1 A2 A3 bp c D E e HE L Lp v w y Z θ NOTES: 1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION. 2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm. 3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm. November 2006 * REV - 4 www.azmicrotek.com 5 MILLIMETERS MIN MAX 1.10 0.05 0.15 0.80 0.95 0.25 0.25 0.45 0.15 0.28 2.90 3.10 2.90 3.10 0.65 4.70 5.10 0.94 0.40 0.70 0.10 0.10 0.10 0.35 0.70 6O 0O AZ10EL11 AZ100EL11 Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part. November 2006 * REV - 4 www.azmicrotek.com 6