defining a degree of excellence 10 TAP LEADING EDGE CONTROL PRECISE DELAY MODULES Cat 26-R3 .60 + .01 13 bel (DC) (P/N) .375 .350 3 .285 Max .10 Typ .80 Max .015 .004 .22 Max 12 Vcc 14 In 1 Gnd 7 11 10 9 4 5 6 8 4 * .030 .012 .008 Total Delay Delay Rise per Tap Time SMD Thru-Hole S497-0025-10 A497-0025-10 S497-0030-10 S497-0040-10 S497-0050-10 S497-0060-10 A497-0030-10 A497-0040-10 A497-0050-10 A497-0060-10 S497-0070-10 S497-0080-10 S497-0090-10 A497-0070-10 A497-0080-10 A497-0090-10 70 ns 80 ns 90 ns 7 ns 8 ns 9 ns 3 ns 3 ns 3 ns S497-0100-10 A497-0100-10 100 ns 10 ns 3 ns S497-0125-10 S497-0150-10 A497-0125-10 A497-0150-10 125 ns 12.5 ns 150 ns 15 ns 3 ns 3 ns S497-0200-10 S497-0250-10 A497-0200-10 A497-0250-10 200 ns 250 ns 3 ns 3 ns ns 2.5 ns ns ns ns ns 3 4 5 6 ns ns ns ns 20 ns 25 ns 3 ns 3 3 3 3 ns ns ns ns Tolerances Input to Taps + 1 ns or 3 % , Whichever is Greater Delays measured @ 1.5 V levels on Leading Edge only with no loads on Taps Rise and Fall Times measured from 0.75 V to 2.4 V levels * Ref. Delay from P13, Delay P1-P13 = 4.5 ns typical Drive Capabilities Temp. 0 2 .015 Min .045 .018 4 6 Ti m e i n M i n u t e s Pulse Voltage Rise Time Pulse Width Pulse Period Supply Current Supply Voltage 3.2 Volts 3.0 ns (10%-90%) 1.2 x Total Delay 4 x Pulse Width 80 ma Typical 5.0 Volts Electrical Characteristics Min. 4.75 2.0 Max. 5.25 Units V V V ma ma V V V ua ma ma ma ma C % % Vcc Vih Vil Ioh Iol Voh Vol Vik Iih Iil Ios Icch Iccl Ta PW d Supply Voltage Logic 1 Input Voltage Logic 0 Input Voltage Logic 1 Output Current Logic 0 Output Current Logic 1 Output Voltage Logic 0 Output voltage Input Clamp Voltage Logic 1 Input Current Logic 0 Input Current Short Circuit Output Current Logic 1 Supply Current Logic 0 Supply Current Operating Free Air Temperature Min. Input Pulse Width of Total Delay Maximum Duty Cycle Tc Temp. Coeff. of Total Delay (TD) 100 + (25000/TD ) PPM/OC 0.8 -1 20 2.7 -60 0o 40 0.5 -1.2 40 -1.2 -150 50 90 70o 50 Transfer molded for better reliability Compatible with TTL & DTL circuits Terminals: Electro-Tin plate phosphor bronze Performance warranty is limited to specified parameters listed SMD - Tape & Reel available: 32mm Wide x 16mm Pitch, 500 pieces per 13" reel Infra Red 100o C .12 Min Notes 225o C Max Temp. > 185o C for 90 Seconds Max 200 C Ein Trin PW PP Iccl Vcc 20 TTL Loads Max. 10 TTL Loads Max. Recommended Temperature Profile o 100o 90o .20 Max Test Conditions @ 25oC Part Numbers 300o C .285 Max .10 Typ .23 Max .012 .008 - (DC) (P/N) .80 Max Coplanarity + .002 Nh Logic 1 Fanout Nl Logic 0 Fanout bel .325 o .018 * 22.5 * 27 * 36 50 60 .60 + .01 8 Other Delays and Tolerances Available Consult Sales Specifications subject to change without notice. Corporate Office Bel Fuse Inc. 198 Van Vorst Street, Jersey City, NJ 07302-4496 Tel: 201-432-0463 Fax: 201-432-9542 E-Mail: [email protected] Internet: http://www.belfuse.com 14 Far East Office Bel Fuse Ltd. 8F/8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel: 852-2328-5515 Fax: 852-2352-3706 European Office Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Preston PR1 8UD Lancashire, U.K. Tel: 44-1772-556601 Fax: 44-1772-888366