Data Sheet 2.5Gb/s High Sensitivity coplanar APD preamp receiver AT3SGCC The AT3SGCC is an optical receiver offering optimum sensitivity and overload performance for OC-48 optical transport systems. The hermetic packaged fiber pigtailed receiver contains an avalanche photodiode, an AGC low noise pre-amp and a precision thermistor. The RF coplanar data outputs from the package provide differential noise rejection for improved sensitivity. The product has been optimized for use in metro applications, either as a discrete device or within a transceiver, using NRZ modulation, with or without FEC, at data rates up to 2.7Gb/s. The combination of a high performance avalanche photodiode, (APD), low noise AGC pre-amp and RF coplanar package provides unmatched performance for maximising transmission distance. The AGC low noise pre-amp is well suited to dynamic threshold level decision circuitry often used to maximise overall receiver chain performance. Features: • High sensitivity, -35.0dBm typical • Wide dynamic range performance to -3dBm • MSA coplanar receiver package • Differential data outputs • +3.3V operation • RoHS 5/6 compliant Applications: • OC-48 DWDM optical transport systems • OC-48 DWDM metro and long haul systems • STM-16 SDH or OC-48 SONET systems 1 Data Sheet Characteristics On all parameters listed below case temperature = 25°C unless otherwise stated. Operating temperature -5°C to +70°C. Optical wavelength between 1525-1575nm. Data 1575nm to 1610nm available on request. (Operating temperature range of -20°C to +85°C is optional details available upon request). Parameter Symbol Measurement Conditions Min APD breakdown voltage Vbr -5°C to 70°C 40 APD temperature coefficient of breakdown voltage Tvbr -5°C to 70°C 0.09 Transimpedance gain Zt -5°C to 70°C Bandwidth s21 M = 10, small signal Lower cut-off frequency s21 cut-off M = 10, small signal APD sensitivity APD overload Psat Output voltage swing Vout Optical return loss ORL Power supply current Icc Power supply voltage Vcc Output return loss s22 Thermistor resistance RTH Notes:  Load impedance is 50Ω AC-coupled. 2 Sens. Typ Max Unit 65 V 0.1 0.12 V/°C 2.3 3.6 4.7 kΩ 1.8 2.2 3.0 GHz 50 kHz -33.5 dBm 223-1 2.5Gb/s, PRBS @ 25°C. M=optimal ER = 10dB, BER=1x10-10 -35.0 2.5Gb/s, 223-1 PRBS @ 25°C. M=3, ER = 10dB BER=1x10-10 -3 Differential 18 dBm 300 30 3.0 DC – 3.0 GHz dB 44 65 mA 3.3 3.6 V 10 9.5 mV pk-pk dB 10.5 kΩ Data Sheet Absolute Maximum Ratings Parameter Symbol Min Max `Unit Operating case temperature Top -40 +85 °C Storage temperature Tstg -40 +85 °C +3 dBm Optical input power Power supply voltage -0.5 3.6 V APD supply voltage M3 Vbr V Fiber bend radius 25 mm Lead soldering time at 260°C 10 s Notes:  The breakdown voltage and APD bias data will vary from device to device. Each modulae will be supplied with deliverable data, in the form of Vbr and APD bias voltages relative to a 10kV thermistor resistance. Schematic Diagram Figure  AT3SGCC schematic diagram 3 Data Sheet Pin Out Pin # Function Pin # Function 1 Case ground 10 +ve RF output 2 APD photodiode bias 11 Case RF ground 3 No connection 12 Case ground 4 No connection 13 No connection 5 No connection 14 Amplifier bias (3.3 Volts) 6 Case ground 15 No connection 7 Case RF ground 16 Thermistor 8 -ve RF output 17 Case ground 9 Case RF ground Schematic Diagram Fiber is 900um secondary coated single-mode fiber, length = 900 - 1100mm 4 Data Sheet RoHS Compliance Bookham is fully committed to environment protection and sustainable development and has set in place a comprehensive program for removing polluting and hazardous substances from all of its products. The relevant evidence of RoHS compliance is held as part of our controlled documentation for each of our compliant products. RoHS compliance parts are available to order, please refer to the ordering information section for further details. Ordering Information: AT3SGCC - (Connector) J28 = SC/PC J34 = FC/PC J57 = LC J59 = MU e.g. AT3SGCC-J28 is an AT3SGCC with an SC/PC connector Other options available on request. Contact Information North America Bookham Worldwide Headquarters Europe Paignton Office Asia Shenzhen Office 2584 Junction Ave. San Jose CA 95134 USA Brixham Road Paignton Devon TQ4 7BE United Kingdom 2 Phoenix Road Futian Free Trade Zone Shenzhen 518038 China • Tel: +1 408 919 1500 • Tel: +44 (0) 1803 66 2000 • Fax: +1 408 919 6083 • Fax: +44 (0) 1803 66 2801 • Fax: +86 755 33305805 +86 755 33305807 www.bookham.com [email protected] 5 ISO14001:1996 EMS 504193 TL9000 Rev 3.0 (ISO9001:2000) FM15040 • Tel: +86 755 33305888 Important Notice Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by Bookham before they become applicable to any particular order or contract. In accordance with the Bookham policy of continuous improvement specifications may change without notice. The publication of information in this data sheet does not imply freedom from patent or other protective rights of Bookham or others. Further details are available from any Bookham sales representative. BH12850 Rev 1.0 January 2007. ©Bookham 2006. Bookham is a registered trademark of Bookham Inc.