CIRRUS CS5343-DZZR

CS5343/4
98 dB, 96 kHz, Multi-Bit Audio A/D Converter
Features
General Description
! Advanced Multi-Bit ∆Σ Architecture
The CS5343/4 is a complete analog-to-digital converter
for digital audio systems. It performs sampling, analogto-digital conversion, and anti-alias filtering, generating
24-bit values for both left and right inputs in serial form
at sample rates up to 108 kHz per channel.
! 24-bit Conversion
! Supports Audio Sample Rates Up to 108 kHz
! 98 dB Dynamic Range at 5 V
The CS5343/4 uses a 3rd-order, multi-bit Delta-Sigma
modulator followed by a digital filter, which removes the
need for an external anti-alias filter.
! -90 dB THD+N
! Low-Latency Digital Filter
The CS5343/4 also features a high-impedance sampling network which eliminates costly external
components such as op-amps.
! High-Pass Filter to Remove DC Offsets
! Single +3.3 V or +5 V Power Supply
! Power Consumption Less Than 50 mW
The CS5343/4 is available in a 10-pin TSSOP package
for both Commercial (-10° to +70° C) and Automotive
grades (-40° to +85° C). The CDB5343 Customer Demonstration Board is also available for device evaluation
and implementation suggestions. Please refer to the
“Ordering Information” on page 21 for complete details.
! Master or Slave Operation
! Slave Mode Speed Auto-Detect
! Master Mode Default Settings
! 256x or 384x MCLK/LRCK Ratio
! CS5343 Supports I²S Audio Format
! CS5344 Supports Left-Justified Audio Format
The CS5343/4 is ideal for audio systems requiring wide
dynamic range, negligible distortion and low noise, such
as set-top boxes, DVD-karaoke players, DVD recorders, A/V receivers, and automotive applications.
VA
3.3 V to 5 V
AINL
High-Z
Sampling
Network
FILT+
AINR
Low-Latency
Digital Filters
Internal
Reference
Voltages
VQ
Single-Ended
Analog Input
High-Pass
Filter
High-Z
Sampling
Network
Advance Product Information
http://www.cirrus.com
High-Pass
Filter
Master
Clock
Auto-detect
MCLK Divider
Serial Port
Single-Ended
Analog Input
SCLK
Slave Mode
Auto-detect
LRCK
Low-Latency
Digital Filters
SDOUT
This document contains information for a new product.
Cirrus Logic reserves the right to modify this product without notice.
Copyright © Cirrus Logic, Inc. 2006
(All Rights Reserved)
AUGUST '06
DS687A4
CS5343/4
TABLE OF CONTENTS
1. PIN DESCRIPTIONS .............................................................................................................................. 4
2. CHARACTERISTICS AND SPECIFICATIONS ...................................................................................... 5
SPECIFIED OPERATING CONDITIONS ............................................................................................... 5
ABSOLUTE MAXIMUM RATINGS ......................................................................................................... 5
ANALOG CHARACTERISTICS - COMMERCIAL GRADE .................................................................... 6
ANALOG CHARACTERISTICS - AUTOMOTIVE GRADE ..................................................................... 7
DIGITAL FILTER CHARACTERISTICS ................................................................................................ 8
DC ELECTRICAL CHARACTERISTICS ................................................................................................ 8
DIGITAL CHARACTERISTICS .............................................................................................................. 9
SYSTEM CLOCKING AND SERIAL AUDIO INTERFACE ................................................................... 10
3. TYPICAL CONNECTION DIAGRAM ................................................................................................... 12
4. APPLICATIONS ................................................................................................................................... 13
4.1 Operation as Clock Master or Slave ............................................................................................... 13
4.1.1 Slave Mode Operation ........................................................................................................... 13
4.1.2 Master Mode Operation ......................................................................................................... 14
4.1.2.1 Master Mode Speed Selection ................................................................................... 14
4.1.3 Master Clock ......................................................................................................................... 14
4.2 Serial Audio Interface ..................................................................................................................... 15
4.3 Digital Interface ............................................................................................................................... 15
4.4 Analog Connections ....................................................................................................................... 15
4.4.1 Component Values ................................................................................................................ 16
4.5 Grounding and Power Supply Decoupling ...................................................................................... 16
4.6 Synchronization of Multiple Devices ............................................................................................... 17
5. FILTER PLOTS ................................................................................................................................... 17
6. PARAMETER DEFINITIONS ................................................................................................................ 19
7. PACKAGE DIMENSIONS .................................................................................................................... 20
THERMAL CHARACTERISTICS .......................................................................................................... 20
8. ORDERING INFORMATION ................................................................................................................ 21
9. REVISION HISTORY ............................................................................................................................ 21
LIST OF FIGURES
Figure 1. CS5343 I²S Serial Audio Interface .............................................................................................. 11
Figure 2. CS5344 Left-Justified Serial Audio Interface .............................................................................. 11
Figure 3. Typical Connection Diagram....................................................................................................... 12
Figure 4. I²S Serial Audio Interface ............................................................................................................ 15
Figure 5. Left-Justified Serial Audio Interface ............................................................................................ 15
Figure 6. CS5343/4 Analog Input Network................................................................................................. 15
Figure 7. CS5343/4 Example Analog Input Network.................................................................................. 16
Figure 8. Single-Speed Mode Stopband Rejection .................................................................................... 17
Figure 9. Single-Speed Mode Transition Band .......................................................................................... 17
Figure 10. Single-Speed Mode Transition Band (Detail)............................................................................ 17
Figure 11. Single-Speed Mode Passband Ripple ...................................................................................... 17
Figure 12. Double-Speed Mode Stopband Rejection................................................................................. 18
Figure 13. Double-Speed Mode Transition Band....................................................................................... 18
Figure 14. Double-Speed Mode Transition Band (Detail) .......................................................................... 18
Figure 15. Double-Speed Mode Passband Ripple..................................................................................... 18
2
DS687A4
CS5343/4
LIST OF TABLES
Table 1. Master/Slave Mode Selection ...................................................................................................... 13
Table 2. Speed Modes and the Associated Sample Rates (Fs) in Slave Mode......................................... 13
Table 3. Speed Modes and the Associated Sample Rates (Fs) in Master Mode....................................... 14
Table 4. Speed Mode Selection in Master Mode ....................................................................................... 14
Table 5. Common MCLK Frequencies in Master and Slave Modes .......................................................... 14
Table 6. Analog Input Design Parameters ................................................................................................. 16
DS687A4
3
CS5343/4
1. PIN DESCRIPTIONS
Pin Name Pin #
SDOUT
1
10
SCLK
2
9
GND
LRCK
3
8
AINR
MCLK
4
7
VQ
FILT+
5
6
AINL
VA
Pin Description
SDOUT
1
Serial Audio Data Output (Output) - Output for two’s complement serial audio data. Also selects Master
or Slave Mode.
SCLK
2
Serial Clock (Input/Output) - Serial clock for the serial audio interface.
LRCK
3
Left Right Clock (Input/Output) - Determines which channel, Left or Right, is currently active on the
serial audio data line.
MCLK
4
Master Clock (Input) - Clock source for the delta-sigma modulator and digital filters.
FILT+
5
Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling circuits.
AINL
AINR
6
8
Analog Input (Input) - The full-scale analog input level is specified in the Analog Characteristics specification table.
VQ
7
Quiescent Voltage (Output) - Filter connection for the internal quiescent reference voltage.
GND
9
Ground (Input) - Ground reference. Must be connected to analog ground.
VA
10
Power (Input) - Positive power supply for the digital and analog sections.
4
DS687A4
CS5343/4
2. CHARACTERISTICS AND SPECIFICATIONS
(All Min/Max characteristics and specifications are guaranteed over the Specified Operating Conditions. Typical
performance characteristics and specifications are derived from measurements taken at typical supply voltages
and TA = 25°C.)
SPECIFIED OPERATING CONDITIONS
(GND = 0 V, all voltages with respect to GND.)
Parameter
Power Supplies
Ambient Operating Temperature
Commercial
Automotive
Symbol
Min
Typ
Max
Unit
VA
3.1
4.75
3.3
5.0
3.5
5.25
V
V
TAC
TAD
-10
-40
-
70
85
°C
°C
ABSOLUTE MAXIMUM RATINGS
(GND = 0 V, all voltages with respect to GND.) (Note 1)
Parameter
DC Power Supplies
Symbol
Min
Max
Unit
VA
-0.3
+6.0
V
Input Current
(Note 2)
Iin
-10
+10
mA
Input Voltage
(Note 3)
VIN
-0.7
VA+0.7
V
Ambient Operating Temperature (Power Applied)
TA
-50
+115
°C
Storage Temperature
Tstg
-65
+150
°C
Notes:
1. Operation beyond these limits may result in permanent damage to the device. Normal operation is not
guaranteed at these extremes.
2. Any pin except supplies. Transient currents of up to ±100 mA on the analog input pins will not cause
SCR latch-up.
3. The maximum over/under voltage is limited by the input current.
DS687A4
5
CS5343/4
ANALOG CHARACTERISTICS - COMMERCIAL GRADE
Test conditions (unless otherwise specified): Input test signal is a 1 kHz sine wave; measurement bandwidth is
10 Hz to 20 kHz; source impedance less than or equal to 2.5 kΩ.
Dynamic Performance for Commercial Grade
Single-Speed Mode
Fs = 48 kHz
Dynamic Range
A-weighted
unweighted
Total Harmonic Distortion + Noise
Double-Speed Mode
Dynamic Range
Total Harmonic Distortion + Noise
VA = 3.3 V
Min
Typ
Max
Min
Typ
Max
Unit
89
86
95
92
-
92
89
98
95
-
dB
dB
-
-86
-75
-35
-80
-
-
-90
-78
-38
-84
-
dB
dB
dB
Fs = 96 kHz
Min
Typ
Max
Min
Typ
Max
Unit
A-weighted
unweighted
89
86
95
92
-
92
89
98
95
-
dB
dB
-
-86
-75
-35
-80
-
-
-90
-78
-38
-84
-
dB
dB
dB
(Note 4)
-1 dB
-20 dB
-60 dB
(Note 4)
-1 dB
-20 dB
-60 dB
Symbol
VA = 5.0 V
THD+N
THD+N
Dynamic Performance for Commercial Grade - All Modes
Min
Typ
Max
Unit
-
90
-
dB
Interchannel Gain Mismatch
-
-
0.1
dB
Gain Error
-3
-
+3
%
Gain Drift
-
±100
-
ppm/°C
0.51*VA
0.56*VA
0.57*VA
Vpp
-
7.5
-
MΩ
Interchannel Isolation
DC Accuracy
Analog Input Characteristics
Full-scale Input Voltage
Input Impedance
Notes:
4. Referred to the typical full-scale input voltage
6
DS687A4
CS5343/4
ANALOG CHARACTERISTICS - AUTOMOTIVE GRADE
Test conditions (unless otherwise specified): Input test signal is a 1 kHz sine wave; measurement bandwidth is
10 Hz to 20 kHz; source impedance less than or equal to 2.5 kΩ.
Dynamic Performance for Automotive Grade
Single-Speed Mode
Dynamic Range
Total Harmonic Distortion + Noise
Double-Speed Mode
Dynamic Range
Total Harmonic Distortion + Noise
Fs = 48 kHz
VA = 3.3 V
Symbol
VA = 5.0 V
Min
Typ
Max
Min
Typ
Max
Unit
87
84
95
92
-
90
87
98
95
-
dB
dB
-
-86
-75
-35
-78
-
-
-90
-78
-38
-82
-
dB
dB
dB
Fs = 96 kHz
Min
Typ
Max
Min
Typ
Max
Unit
A-weighted
unweighted
87
84
95
92
-
90
87
98
95
-
dB
dB
-
-86
-75
-35
-78
-
-
-90
-78
-38
-82
-
dB
dB
dB
A-weighted
unweighted
(Note 5)
-1 dB
-20 dB
-60 dB
(Note 5)
-1 dB
-20 dB
-60 dB
THD+N
THD+N
Dynamic Performance for Automotive Grade - All Modes
Min
Typ
Max
Unit
-
90
-
dB
Interchannel Gain Mismatch
-
-
0.1
dB
Gain Error
-3
-
+3
%
Gain Drift
-
±100
-
ppm/°C
0.51*VA
0.56*VA
0.57*VA
Vpp
-
7.5
-
MΩ
Interchannel Isolation
DC Accuracy
Analog Input Characteristics
Full-scale Input Voltage
Input Impedance
Notes:
5. Referred to the typical full-scale input voltage
DS687A4
7
CS5343/4
DIGITAL FILTER CHARACTERISTICS
Parameter
Single-Speed Mode
Passband
Symbol
Min
Typ
Max
Unit
Fs = 4 - 54 kHz
0
-
0.489
Fs
Passband Ripple
(-0.1 dB)
-0.025
-
0.025
dB
Stopband
0.560
-
-
Fs
69
-
-
dB
-
12/Fs
-
s
0
-
0.489
Fs
Passband Ripple
-0.025
-
0.025
dB
Stopband
0.560
-
-
Fs
69
-
-
dB
-
9/Fs
-
s
-
1
20
-
Hz
Hz
-
10
-
Deg
-
-
0
dB
Stopband Attenuation
Total Group Delay (Fs = Output Sample Rate)
Double-Speed Mode
Passband
tgd
Fs = 86 - 108 kHz
(-0.1 dB)
Stopband Attenuation
Total Group Delay (Fs = Output Sample Rate)
tgd
High-Pass Filter Characteristics
Frequency Response
Phase Deviation
-3.0 dB
-0.13 dB
(Note 6)
@ 20 Hz
(Note 6)
Passband Ripple
Notes:
6. Response shown is for Fs equal to 48 kHz. Filter characteristics scale with Fs.
DC ELECTRICAL CHARACTERISTICS
(GND = 0 V, all voltages with respect to 0 V. MCLK=12.288 MHz; Master Mode)
VA = 3.3 V
Parameter
Symbol Min
DC Power Supplies:
Typ
VA = 5.0 V
Max Min
Typ
Max
Unit
VA
3.1
3.3
-
-
5
5.25
V
Power Supply Current
(Normal Operation)
IA
-
15
-
-
15
-
mA
Power Supply Current
(Power-Down Mode) (Note 7)
IA
-
1.1
-
-
1.1
-
mA
Power Consumption
(Normal Operation)
(Power-Down Mode) (Note 7)
-
-
50
3.6
-
-
75
5.5
-
mW
mW
Parameter
Symbol
Min
Typ
Max
Unit
PSRR
-
65
-
dB
VQ Nominal Voltage
Output Impedance
-
0.44xVA
25
-
V
kΩ
Filt+ Nominal Voltage
Output Impedance
Maximum allowable DC current source/sink
-
VA
220
2.5
-
V
kΩ
uA
Power Supply Rejection Ratio (1 kHz)
(Note 8)
Notes:
7. Device enters power-down mode when MCLK is held static.
8. Valid with the recommended capacitor values on FILT+ and VQ as shown in the Typical Connection
Diagram.
8
DS687A4
CS5343/4
DIGITAL CHARACTERISTICS
Symbol
Min
Typ
Max
Units
High-Level Input Voltage
Parameter
(% of VA)
VIH
70
-
-
%
Low-Level Input Voltage
(% of VA)
VIL
-
-
30
%
High-Level Output Voltage at Io = 500 µA
(% of VA)
VOH
70
-
-
%
Low-Level Output Voltage at Io =500 µA
(% of VA)
VOL
-
-
15
%
Iin
-10
-
10
µA
Input Leakage Current
DS687A4
9
CS5343/4
SYSTEM CLOCKING AND SERIAL AUDIO INTERFACE
(Logic “0” = GND = 0 V; Logic “1” = VA, CL = 20 pF)
Parameter
Symbol
Min
Typ
Max
Unit
tclkw
24
-
30
ns
(Double-Speed, 192x Mode)
48
-
60
ns
(Double-Speed, 256x Mode)
36
-
45
ns
(Double-Speed, 128x Mode)
72
-
90
ns
(Single-Speed, 768x Mode)
24
-
325
ns
(Single-Speed, 384x Mode)
48
-
651
ns
(Single-Speed, 512x Mode)
36
-
488
ns
(Single-Speed, 256x Mode)
72
-
976
ns
40
50
60
%
4
86
-
54
108
kHz
kHz
LRCK Duty Cycle
-
50
-
%
SCLK Duty Cycle
-
50
-
%
Master Mode
MCLK Period
(Double-Speed, 384x Mode)
MCLK Duty Cycle
Output Sample Rate
(Single-Speed)
(Double-Speed)
Fs
SDOUT valid before SCLK rising
tstp
10
-
-
ns
SDOUT valid after SCLK rising
thld
40
-
-
ns
SCLK falling to LRCK edge
tslrd
-20
-
20
ns
tclkw
24
-
30
ns
(Double-Speed, 192x Mode)
48
-
60
ns
(Double-Speed, 256x Mode)
36
-
45
ns
(Double-Speed, 128x Mode)
72
-
90
ns
(Single-Speed, 768x Mode)
24
-
325
ns
(Single-Speed, 384x Mode)
48
-
651
ns
(Single-Speed, 512x Mode)
36
-
488
ns
(Single-Speed, 256x Mode)
72
-
976
ns
40
50
60
%
4
86
-
54
108
kHz
kHz
40
50
60
%
1 ----------------64 × Fs
-
-
ns
45
50
55
%
Slave Mode
MCLK Period
(Double-Speed, 384x Mode)
MCLK Duty Cycle
Input Sample Rate
(Single-Speed)
(Double-Speed)
Fs
LRCK Duty Cycle
SCLK Period
tsclkw
SCLK Duty Cycle
SDOUT valid before SCLK rising
tstp
10
-
-
ns
SDOUT valid after SCLK rising
thld
10
-
-
ns
SCLK falling to LRCK edge
tslrd
-20
-
20
ns
10
DS687A4
CS5343/4
t slrd
LRCK
t sclkw
SCLK
SDOUT
MSB
t stp
MSB-1
t hld
Figure 1. CS5343 I²S Serial Audio Interface
t slrd
LRCK
t sclkw
SCLK
SDOUT
MSB
t stp
MSB-1
t hld
Figure 2. CS5344 Left-Justified Serial Audio Interface
DS687A4
11
CS5343/4
3. TYPICAL CONNECTION DIAGRAM
3.3 V to 5 V
0.1 µF
1 µF
VA or
GND
10
VA
1 µF
CS5343/4
0.1 µF
9
GND
7
VQ
0.1 µF
6
AINL
Analog Input
Conditioning
SDOUT
1
SCLK
2
LRCK
3
MCLK
4
See Figure 6 on
page 15
Audio
Processor/
System
Clocks
1
8
10 kΩ2
FILT+
10 kΩ2
1 µF
VA
10 kΩ1
5
Pull-up to VA for Master Mode
Pull-down to GND for Slave Mode
AINR
2
Optional pull-up resistor for configuring clocks in Master Mode as desribed
in the “Master Mode Speed Selection”
section on page 14
Figure 3. Typical Connection Diagram
12
DS687A4
CS5343/4
4. APPLICATIONS
4.1
Operation as Clock Master or Slave
The CS5343/4 supports operation as either a clock master or slave. As a clock master, the left/right and
serial clocks are synchronously generated on-chip and output on the LRCK and SCLK pins, respectively.
As a clock slave, the LRCK and SCLK pins are always inputs and require external generation of the left/right
and serial clocks. The selection of clock master or slave is made via a 10 kΩ pull-up resistor from SDOUT
to VA for Master Mode selection or via a 10 kΩ pull-down resistor from SDOUT to GND for Slave Mode selection, as shown in Table 1.
Mode
Selection
Master Mode
10 kΩ pull-up resistor from SDOUT to VA
Slave Mode
10 kΩ pull-down resistor from SDOUT to GND
Table 1. Master/Slave Mode Selection
4.1.1
Slave Mode Operation
A unique feature of the CS5343/4 is the automatic selection of either Single- or Double-Speed Mode when
acting as a clock slave. The auto-mode selection feature supports all standard audio sample rates from
4 to 108 kHz. Please refer to Table 2 for supported sample rate ranges in Slave Mode.
Speed Mode
Single-Speed Mode
Double-Speed Mode
MCLK/LRCK
Ratio
SCLK/LRCK
Ratio
Input Sample Rate Range (kHz)
256x
64
4 - 54
512x
64
4 - 54
384x
48, 64
4 - 54
768x
48, 64
4 - 54
128x
64
86 - 108
256x
64
86 - 108
192x
48, 64
86 - 108
384x
48, 64
86 - 108
Table 2. Speed Modes and the Associated Sample Rates (Fs) in Slave Mode
DS687A4
13
CS5343/4
4.1.2
Master Mode Operation
As clock Master, the CS5343/4 generates LRCK and SCLK synchronously on-chip. Table 3 shows the
available sample rates and associated clock ratios in Master Mode.
Speed Mode
Single-Speed Mode
Double-Speed Mode
MCLK/LRCK
Ratio
SCLK/LRCK
Ratio
Input Sample Rate Range (kHz)
256x
64
4 - 54
512x
64
4 - 54
384x
64
4 - 54
768x
64
4 - 54
128x
64
86 - 108
256x
64
86 - 108
192x
64
86 - 108
384x
64
86 - 108
Table 3. Speed Modes and the Associated Sample Rates (Fs) in Master Mode
4.1.2.1
Master Mode Speed Selection
During power-up in Master Mode, the LRCK and SCLK pins are inputs to configure speed mode and the
output clock ratio. The LRCK pin is pulled low internally to select Single-Speed Mode by default, but Double-Speed Mode is accessed with a 10 kΩ pull-up resistor from LRCK to VA as shown in Table 4. Similarly, the SCLK pin is internally pulled-low by default to select a 256x MCLK/LRCK ratio, but a
MCLK/LRCK ratio of 348x is accessed with a 10 kΩ pull-up resistor from SCLK to VA as shown in Table 4.
Following the power-up routine, the LRCK and SCLK pins become clock outputs.
Pin
LRCK
SCLK
Resistor Option
Clock Configuration
Internal Pull-Down to GND (100 kΩ)
Single-Speed Mode (default)
External Pull-Up to VA (10 kΩ)
Double-Speed Mode
Internal Pull-Down to GND (100 kΩ)
256x MCLK/LRCK (default)
External Pull-Up to VA (10 kΩ)
384x MCLK/LRCK
Table 4. Speed Mode Selection in Master Mode
4.1.3
Master Clock
The CS5343/4 requires a Master clock (MCLK) which runs the internal sampling circuits and digital filters.
There is also an internal MCLK divider which is automatically activated based on the frequency of the
MCLK. Table 4 lists some common audio output sample rates and the required MCLK frequency.
Sample Rate (kHz)
Master and Slave Mode
MCLK(MHz)
Speed Mode
32
44.1
48
SSM
SSM
SSM
Sample Rate (kHz)
Speed Mode
88.2
96
DSM
DSM
256x
8.912
11.289
12.288
512x
16.384
22.579
24.576
MCLK (MHz)
384x
12.288
16.934
18.432
MCLK(MHz)
128x
11.289
12.288
256x
22.579
24.576
768x
24.576
33.868
36.864
MCLK (MHz)
192x
16.934
18.432
384x
33.868
36.864
Table 5. Common MCLK Frequencies in Master and Slave Modes
14
DS687A4
CS5343/4
4.2
Serial Audio Interface
The CS5343 output is serial data in I²S audio format and the CS5344 output is serial data in Left-Justified
audio format. Figures 4 and 5 show the I²S and Left-Justified data relative to SCLK and LRCK. Additionally,
Figures 1 and 2 display more information on the required timing for the serial audio interface format. For an
overview of serial audio interface formats, please refer to Cirrus Application Note AN282.
Left Channel
LRCK
Right Channel
SCLK
SDATA
23 22
9
8
7
6
5
4
3
2
1
0
23 22
9
8
7
6
5
4
3
2
1
0
23 22
Figure 4. I²S Serial Audio Interface
Left Channel
LRCK
Right Channel
SCLK
SDATA
23 22
9
8
7
6
5
4
3
2
1
0
23 22
9
8
7
6
5
4
3
2
1
0
23 22
Figure 5. Left-Justified Serial Audio Interface
4.3
Digital Interface
VA supplies power to both the analog and digital sections of the ADC, and also powers the serial port. Consequently, the digital interface logic level must equal VA to within the limits specified under “Digital Characteristics” on page 9.
4.4
Analog Connections
The analog modulator samples the input signal at half of the internal master clock rate, or 6.144 MHz when
MCLK = 12.288 MHz. The digital filter will reject signals within the stopband of the filter. However, there is
no rejection for input signals which are multiples of the input sampling frequency (n × 6.144 MHz), where
n=0,1,2,... Refer to Figure 6 which shows the recommended topology of the analog input network. The external shunt capacitor and internal input impedance form a single-pole RC filter to provide the appropriate
filtering of noise at the modulator sampling frequency. Additionally, the 180 pF capacitor acts as a charge
source for the internal sampling circuits. Capacitors of NPO or other high-quality dielectric will produce the
best results while capacitors with a large voltage coefficient (such as general-purpose ceramics) can degrade signal linearity.
R1
1 µF
Input
CS5343/4
AIN
R2
180pF
C0G
Figure 6. CS5343/4 Analog Input Network
DS687A4
15
CS5343/4
4.4.1
Component Values
Three parameters determine the values of resistors R1 and R2 as shown in Figure 6: source impedance,
attenuation, and input impedance. Table 6 shows the design equation used to determine these values.
•
Source Impedance: Source impedance is defined as the impedance as seen from the ADC looking
back into the signal network. The ADC achieves optimal THD+N performance with a source impedance less than or equal to 2.5 kΩ.
•
Attenuation: The required attenuation factor depends on the magnitude of the input signal. The fullscale input voltage is specified under “Analog Characteristics - Commercial Grade” on page 6. The
user should select values for R1 and R2 such that the magnitude of the incoming signal multiplied by
the attenuation factor is less than or equal to the full-scale input voltage of the device.
•
Input Impedance: Input impedance is the impedance from the signal source to the ADC analog input
pins. Table 6 shows the input parameters and the associated design equations.
Source Impedance
(-----------------------R1 × R2 )R1 + R2
Attenuation Factor
( R2 )
------------------------( R1 + R2 )
Input Impedance
( R1 + R2 )
Table 6. Analog Input Design Parameters
Figure 7 illustrates an example configuration using two 4.99 kΩ resistors in place of R1 and R2. Based on
the discussion above, this circuit provides an optimal interface for both the ADC and the signal source.
First, consumer equipment frequently requires an input impedance of 10 kΩ, which the 4.99 kΩ resistors
provide. Second, this circuit will attenuate a typical line level voltage, 2 Vrms, to the full-scale input of the
ADC, 1 Vrms when VA = 5 V. Finally, at 2.5 kΩ, the source impedance optimizes analog performance of
the ADC.
4.99 kΩ
1 µF
Input
CS5343/4
AIN
4.99 kΩ
180pF
C0G
Figure 7. CS5343/4 Example Analog Input Network
4.5
Grounding and Power Supply Decoupling
As with any high-resolution converter, designing with the CS5343/4 requires careful attention to power supply and grounding arrangements if its potential performance is to be realized. Figure 3 shows the recommended power arrangements, with VA connected to a clean supply. Decoupling capacitors should be as
near to the ADC as possible, with the low value ceramic capacitor being the nearest. All signals, especially
clocks, should be kept away from the FILT+ and VQ pins in order to avoid unwanted coupling into the modulators. The FILT+ and VQ decoupling capacitors, particularly the 0.01 µF, must be positioned to minimize
the electrical path from FILT+ to GND. The CDB5343 evaluation board demonstrates the optimum layout
and power supply arrangements. To minimize digital noise, connect the ADC digital outputs only to CMOS
inputs.
16
DS687A4
CS5343/4
4.6
Synchronization of Multiple Devices
In systems where multiple ADCs are required, care must be taken to achieve simultaneous sampling. To
ensure synchronous sampling, the MCLK, SCLK, and LRCK must be the same for all of the CS5343 and
CS5344 devices in the system.
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
Amplitude (dB)
Amplitude (dB)
5. FILTER PLOTS
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
0.40 0.42 0.44
Frequency (norm alized to Fs)
0
0.10
-1
0.08
-2
0.06
-3
-4
-5
-6
-7
0.51
0.52
Frequency (norm alized to Fs)
Figure 10. Single-Speed Mode Transition Band (Detail)
DS687A4
0.60
0.00
-0.04
-0.08
0.50
0.58
-0.02
-0.06
0.49
0.56
0.02
-9
0.48
0.54
0.04
-8
0.47
0.52
Figure 9. Single-Speed Mode Transition Band
Amplitude (dB)
Amplitude (dB)
Figure 8. Single-Speed Mode Stopband Rejection
-10
0.46
0.46 0.48 0.50
Frequency (norm alized to Fs)
-0.10
0.00 0.05
0.10
0.15
0.20 0.25 0.30 0.35 0.40 0.45 0.50
Frequency (norm alized to Fs)
Figure 11. Single-Speed Mode Passband Ripple
17
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
0.40 0.42 0.44
Amplitude (dB)
Amplitude (dB)
CS5343/4
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
Frequency (norm alized to Fs)
0.10
0.08
-2
0.06
Amplitude (dB)
Amplitude (dB)
0
-3
-4
-5
-6
-7
0.52
Frequency (norm alized to Fs)
Figure 14. Double-Speed Mode Transition Band (Detail)
18
0.00
-0.04
-0.08
0.51
0.60
-0.02
-0.06
0.50
0.58
0.02
-9
0.49
0.56
0.04
-8
0.48
0.54
Figure 13. Double-Speed Mode Transition Band
-1
0.47
0.52
Frequency (norm alized to Fs)
Figure 12. Double-Speed Mode Stopband Rejection
-10
0.46
0.46 0.48 0.50
-0.10
0.00 0.05
0.10
0.15
0.20 0.25 0.30 0.35 0.40 0.45 0.50
Frequency (norm alized to Fs)
Figure 15. Double-Speed Mode Passband Ripple
DS687A4
CS5343/4
6. PARAMETER DEFINITIONS
Dynamic Range
The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified
bandwidth. Dynamic Range is a signal-to-noise ratio measurement over the specified bandwidth made with
a -60 dBFS signal. 60 dB is added to resulting measurement to refer the measurement to full-scale. This
technique ensures that the distortion components are below the noise level and do not affect the measurement. This measurement technique has been accepted by the Audio Engineering Society, AES17-1991,
and the Electronic Industries Association of Japan, EIAJ CP-307. Expressed in decibels.
Total Harmonic Distortion + Noise
The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified
bandwidth (typically 10 Hz to 20 kHz), including distortion components. Expressed in decibels. Measured
at -1 and -20 dBFS as suggested in AES17-1991 Annex A.
Frequency Response
A measure of the amplitude response variation from 10 Hz to 20 kHz relative to the amplitude response at
1 kHz. Units in decibels.
Interchannel Isolation
A measure of crosstalk between the left and right channels. Measured for each channel at the converter's
output with no signal to the input under test and a full-scale signal applied to the other channel. Units in decibels.
Interchannel Gain Mismatch
The gain difference between left and right channels. Units in decibels.
Gain Error
The deviation from the nominal full-scale analog input for a full-scale digital output.
Gain Drift
The change in gain value with temperature. Units in ppm/°C.
Offset Error
The deviation of the mid-scale transition (111...111 to 000...000) from the ideal. Units in mV.
DS687A4
19
CS5343/4
7. PACKAGE DIMENSIONS
10LD TSSOP (3 mm BODY) PACKAGE DRAWING (Note 1)
N
D
E11
c
E
A2
A
∝
e
b
A1
SIDE VIEW
1 2 3
END VIEW
L
SEATING
PLANE
L1
TOP VIEW
INCHES
DIM
MIN
A
A1
A2
b
c
D
E
E1
e
L
L1
µ
-0
0.0295
0.0059
0.0031
----0.0157
-0°
MILLIMETERS
NOM
MAX
MIN
-0.0433
--0.0059
0
-0.0374
0.75
-0.0118
0.15
-0.0091
0.08
0.1181 BSC
--0.1929 BSC
--0.1181 BSC
--0.0197 BSC
--0.0236
0.0315
0.40
0.0374 REF
---8°
0°
Controlling Dimension is Millimeters
NOTE
NOM
MAX
-----3.00 BSC
4.90 BSC
3.00 BSC
0.50 BSC
0.60
0.95 REF
--
1.10
0.15
0.95
0.30
0.23
----0.80
-8°
4, 5
2
3
Notes:
1. Reference document: JEDEC MO-187
2. D does not include mold flash or protrusions which is 0.15 mm max. per side.
3. E1 does not include inter-lead flash or protrusions which is 0.15 mm max per side.
4. Dimension b does not include a total allowable dambar protrusion of 0.08 mm max.
5. Exceptions to JEDEC dimension.
THERMAL CHARACTERISTICS
Parameter
Allowable Junction Temperature
Junction to Ambient Thermal Impedance
(4-layer PCB)
(2-layer PCB)
20
Symbol
Min
Typ
Max
Unit
TJ
-
-
135
°C
θJA-4
θJA-2
-
100
170
-
°C/W
°C/W
DS687A4
CS5343/4
8. ORDERING INFORMATION
Product
Description
98 dB, Multi-Bit Audio
CS5343
A/D Converter,
I²S Audio Format
98 dB, Multi-Bit Audio
CS5343
A/D Converter,
I²S Audio Format
98 dB, Multi-Bit Audio
CS5344
A/D Converter,
Left-Justified Audio Format
98 dB, Multi-Bit Audio
CS5344
A/D Converter,
Left-Justified Audio Format
CDB5343 CS5343 Evaluation Board
Package
Pb-Free
Grade
Temp Range
10-TSSOP
Yes
Commercial -10° to +70° C
10-TSSOP
Yes
Automotive
10-TSSOP
Yes
Commercial -10° to +70° C
10-TSSOP
Yes
Automotive
-40° to +85° C
-
No
-
-
-40° to +85° C
Container
Rail
Order #
CS5343-CZZ
Tape & Reel
CS5343-CZZR
Rail
CS5343-DZZ
Tape & Reel
CS5343-DZZR
Rail
CS5344-CZZ
Tape & Reel
CS5344-CZZR
Rail
CS5344-DZZ
Tape & Reel
CS5344-DZZR
-
CDB5343
9. REVISION HISTORY
Release
Changes
A2
Changes made to Serial Port diagrams. See Figure 1 and Figure 2 on page 11.
A3
Replaced block diagram on cover page.
Increased minimum hold time (Thld) specification on page 10.
Updated Table 4, “Speed Mode Selection in Master Mode,” on page 14.
A4
Corrected MCLK timing specifications on page 10
Corrected “Typical Connection Diagram” on page 12
Corrected Table 3, “Speed Modes and the Associated Sample Rates (Fs) in Master Mode,” on page 14
Contacting Cirrus Logic Support
For all product questions and inquiries, contact a Cirrus Logic Sales Representative.
To find one nearest you, go to www.cirrus.com.
IMPORTANT NOTICE
"Advance" product information describes products that are in development and subject to development changes. Cirrus Logic, Inc. and its subsidiaries ("Cirrus")
believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS"
without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that
information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment,
including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use
of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of
Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or
other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such
as copying for general distribution, advertising or promotional purposes, or for creating any work for resale.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE
IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT
THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER’S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL
APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND
OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS’ FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION
WITH THESE USES.
Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks
or service marks of their respective owners.
DS687A4
21