CURRENT 16.0 Amperes VOLTAGE 50 to 1000 Volts FP1601 THRU FP1607 Features · Fast switching · Low leakage · Low forward voltage drop · High current capability · High current surge · High reliability ITO-220 2.54 · Case : JEDEC ITO-220 molded plastic body · Terminals : Lead solderable per MIL-STD-750, method 2026 · Polarity : As marked · Mounting Position : Any · Weight : 0.08 ounce, 2.24 gram 0.7 2.54 0.2 PIN 1 PIN 3 Positive CT Suffix "C" 4.5 0.2 2.7 0.2 15 0.3 13Min 2.7 0.2 1.3 0.2 3.7 0. 2 Mechanical Data 0.2 0.1 3.2 6.4 0.1 10 0.5 0.2 0.2 0.5 2.4 0.2 0.2 PIN 1 + CASE PIN 2 PIN 3 Negative CT Suffix "A" CASE PIN 2 Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols FP 1601 FP 1602 FP 1603 FP 1604 FP 1605 FP 1606 FP 1607 Units Maximum recurrent peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts Maximum average forward rectified current See Fig. 1 I(AV) 16.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 150 Amps VF 1.3 Volts Maximum instantaneous forward voltage at 8.0A Maximum DC reverse current at rated DC blocking voltage TC=25℃ TC=125℃ Maximum reverse recovery time (Note 1) Typical thermal resistance (Note 2) Operating junction and storage temperature range 10 IR μA 100 Trr RθJC TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (3) Thermal resistance from junction to case mounted on heatsink. 150 250 5.0 -55 to +150 500 ns ℃/W ℃ RATINGS AND CHARACTERISTIC CURVES FP1601 THRU FP1607 FIG . 1 -REVERSE RECOVERY TIME CHARACTERISTIC 10 50 NONINDUCTIVE (+ ) 50Vdc (approx) (-) NONINDUCTIVE PULSE GENERATOR ( NOTE 2 ) -1.0A 1cm FIG . 2- MAXIMUM FORWARD CURRENT DERATING CURVE 12.0 8.0 4.0 0 0 300 50 100 LEAD TEMPERATURE . (OC ) 150 FIG .4 - MAXIMUM NON - REPETITIVE FORWARD SURGE CURRENT 250 200 INSTANTANEOUS REVERSE CURRENT . ( A) 16.0 100 100 Tj=25OC 1.0 0.1 0 80 50 1 2 5 10 20 NUMBER OF CYCLES AT 60Hz 50 1 00 FIG .5 - TYPICAL JUNCTION CAPACITANCE PER LEG 120 100 80 60 40 20 0.1 Tj=25OC f = 1.0MHz Vsig = 50mVp-p 0.5 1.0 5 10 50 100 REVERSE VOLTAGE . ( V ) 500 1000 Tj=125OC 10 8.3ms Single Half Sine Wave JEDEC Method 150 SET TIME BASE FOR 5/ 10ns / cm FIG . 3 - TYPICAL REVERSE CHARACTERISTICS 1000 20.0 INSTANTANEOUS FORWARD VOLTAGE . ( A ) AVERAGE FORWARD CURRENT ( A ) PEAK FORWARD SURGE CURRENT . ( A ) 0 -0.25A OSCILLOSCOPE (NOTE 1 ) NOTES: 1 . RISE TIME = 7nsmax. INPUT IMPEDANCE= 1 MEGOHM 22pf 2 . RISETIME = 10ns max. SOURSE IMPEDANCE = 50ohmsf CAPACITANCE . ( pF ) trr +0.5A DUT NONINDUCTIVE AND TEST CIRCUIT DIAGRAM 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. ( % ) FIG . 6 - TYPICAL INSTANTANEOUS FORWARD CARACTERISTICS 40 20 10 4 2 1.0 .4 Tj=25OC Pulse Width=300 1% Duty Cycle .2 .1 .8 .9 1.0 1.1 1.2 1.3 1.4 s 1.5 INSTANTANEOUS FORWARD VOLTAGE . ( A )