F E AT U R E S MODEL NO. DSWM9073 1 - 1200 MHz 2 dB Insertion Loss +80 dBm IP2 Amplitude/Phase Balanced HDI Switch Assembly, RF 8 Channel PROTECTIVE SLEEVING 13.50/12.50 WIRE PER MIL-W-22759/33 (SEE CHART FOR P1) FROM BUNDLE WITH TIE CORD ONLY 20 10 P1 102387-4 (AMP) WITH 17 CONTACTS 102548-3 (AMP) FLUSH SURFACE (MTG SURFACE) .25 REF 1.040 2.460 .470 .520 J10 J17 J18 J25 J66 J73 J58 J65 J50 J57 J9 OSP PLUG J2-J9, J26-J49 3.00 REF ALL CONNECTORS SHALL BE DESIGNATED 7 EQUAL SPACES AT .600 = 4.200 OPTIONAL, 6 INSERTS J8 J7 J6 J5 J4 J3 J2 J26 J33 3.00 2.000 A 1.480 .520 .710 J41 J34 J49 J42 1.500 .700 7 EQUAL SPACES AT .600 = 4.200 4-40 UNC-2B TOOLING HOLE, 16 PLACES, REF 1.81/1.79 .400 .40 REF .20 REF VIEW A HOUSING SMA FEMALE J10-J17, J50-J57 BUNDLE 2.30 REF OUTLET 1/3.75 COVER 1 PART IDENTIFICATION 11 1.82 REF 4.82/4.78 OSP PLUG J18-J25, J58-J73 .20 REF .180 .22 TYP, REF 7 EQUAL SPACES AT .600 = 4.200 .180 .200 .138-32 UNC-2B X .25MIN. DEEP THD, 24 INSERTS PI CHART PORT SELECT S1 (J66 to J73) J58 to J65 S3 J58 to J65 S3 J50 to J57 J26 to J33 J34 to J41 J42 to J49 Switch State S2 J10 to J17 J10 to J17 J2 to J9 J2 to J9 Not Sel. Not Sel. Not Sel. Not Sel. DA I C O In d u s t r i e s S3 J18 to J25 S1 J18 to J25 S1 Not Sel. Not Sel. Not Sel. Not Sel. 22 0 0 0 0 1 1 1 1 Port 21 0 0 1 1 0 0 1 1 20 0 1 0 1 0 1 0 1 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Function Strobe 1 Strobe 2 Strobe 3 Strobe 4 Strobe 5 Strobe 6 Strobe 7 Strobe 8 Port 2 0 Port 2 1 Port 2 2 N/C N/C N/C +5V +5V -15V +5V RET +5V RET -15V RET Wire Type 30 Awg, Blk 30 Awg, Brn 30 Awg, Red 30 Awg, Orn 30 Awg, Yel 30 Awg, Grn 30 Awg, Blu 30 Awg, Vio 30 Awg, Gry 30 Awg, Wht 30 Awg, Wht/Blk 26 Awg, Red 26 Awg, Wht/Red 26 Awg, Orn 26 Awg, Blk 26 Awg, Blk 26 Awg, Blk Rev. N/D / Iss. 1