EUTECH EUP7965

EUP7965
150mA Low-Noise Low-Dropout
Linear Regulator
DESCRIPTION
FEATURES
The EUP7965 is designed for portable and wireless
applications with demanding performance and space
requirements.
The EUP7965 is stable with a small 1µF ±30% ceramic
output capacitor. The EUP7965’s performance is
optimized for battery powered systems to deliver low
noise, low dropout voltage, low quiescent current and
excellent line and load transient response.
An optional external bypass capacitor reduces the
output noise further without slowing down the load
transient response. Power supply rejection is better
than 65dB at low frequencies. High power supply
rejection is maintained down to low input voltage
levels common to battery operated circuits. Other
features include a logic-controlled shutdown mode,
short-circuit and thermal-shutdown protection. The
EUP7965 is available in a SOT23-5,SOT23-6 package.
z
z
z
z
z
z
z
z
z
z
z
z
z
2.5 to 5.5V Input Range
150mA Guaranteed Output
70dB PSRR at 1kHz @ VIN=VOUT+1V
50µVrms Output Noise (typ) over 10Hz to
100kHz
100mV Maximum Dropout with 150mA Load
Low 85µA No-load Supply Current
≤ 1.5µA Shutdown Current
Fast Start-up time.
Stable with 1µF Ceramic Capacitors
Thermal Shutdown and Short-circuit Protection
Preset Output Voltage 1.5V, 1.8V, 2.5V, 2.8V,
2.85V, 3.0V ,3.3V, 4.8V ,5.0V and adjustable
SOT23-5,SOT23-6 package
RoHS Compliant and 100% Lead (Pb)-Free
APPLICATIONS
z
z
z
z
Block Diagram
Figure 1.
DS7965 Ver1.5 March. 2006
1
Cellular and Cordless Handsets
Bluetooth, Wireless LAN
PDAs and Palmtop Computers
Portable Information Appliances
EUP7965
Typical Application Circuit
Figure 2.
Figure 3.
DS7965 Ver1.5 March. 2006
2
EUP7965
Pin Configurations
Part Number
Pin Configurations
EUP7965
SOT23-5
EUP7965
SOT23-6
Pin Description
PIN
SOT23-5
SOT23-6
VIN
1
1
Input voltage of the LDO
GND
2
2
Common ground
VEN
3
3
Enable input logic, enable high
BYPASS
4
4
Optional bypass capacitor for noise reduction
Output voltage set. Not externally connected for the fixed versions.
Connect to resistor-divider for adjustable output voltage.
Output voltage of the LDO
SET
VOUT
5
5
DS7965 Ver1.5 March. 2006
6
DESCRIPTION
3
EUP7965
Ordering Information
Order Number
Package Type
Marking
Operating Temperature range
EUP7965-15VIR1
SOT23-5
G0 □ □
-40 °C to 85°C
EUP7965-18VIR1
SOT23-5
G1 □ □
-40 °C to 85°C
EUP7965-25VIR1
SOT23-5
G2 □ □
-40 °C to 85°C
EUP7965-28VIR1
SOT23-5
G6 □ □
-40 °C to 85°C
EUP7965-285VIR1
SOT23-5
G8 □ □
-40 °C to 85°C
EUP7965-30VIR1
SOT23-5
G5 □ □
-40 °C to 85°C
EUP7965-33VIR1
SOT23-5
G3 □ □
-40 °C to 85°C
EUP7965-48VIR1
SOT23-5
G7 □ □
-40 °C to 85°C
EUP7965-50VIR1
SOT23-5
G4 □ □
-40 °C to 85°C
EUP7965VIR1
SOT23-6
GA □ □
-40 °C to 85°C
EUP7965-□ □ □
□ □ □ □
Lead Free Code
1: Lead Free 0: Lead
Packing
R: Tape & Reel
Operating temperature range
I: Industry Standard
Package Type
V: SOT-23
Output Voltage
15: 1.5V
18: 1.8V
25: 2.5V
28: 2.8V
285: 2.85V
30: 3.0V
33: 3.3V
48: 4.8V
50: 5.0V
Blank: Adjustable
DS7965 Ver1.5 March. 2006
4
EUP7965
Absolute Maximum Ratings
„
„
„
„
„
„
„
„
„
VIN,VEN ------------------------------------------------------------------------------- -0.3 to 6V
VOUT ----------------------------------------------------------------- -0.3 to (VIN+0.3) ≤ 6V
Junction Temperature ------------------------------------------------------------------- 150°C
Storage Temperature ------------------------------------------------------ -65°C to +150°C
Lead Temp -----------------------------------------------------------------------------235°C
Pad Temp ------------------------------------------------------------------------------235°C
Maximum Power Dissipation SOT23-5 --------------------------------------------- 364mW
Thermal Resistance θJA(SOT23-5) --------------------------------------------------- 220°C/W
ESD Rating
Human Body Model ------------------------------------------------------------------- 2kV
Operating Ratings
„
„
„
VIN -------------------------------------------------------------------------------------- 2.5 to 5.5V
VEN ------------------------------------------------------------------------- 0 to (VIN+0.3) ≤ 5.5V
Junction Temperature ------------------------------------------------------ -40°C to +125°C
Electrical Characteristics
Unless otherwise specified, all limits guaranteed for VIN= VOUT(nom) +0.5V, CIN=1µF, IOUT=1mA, COUT=1µF,
CBYPASS=0.01µF. Typical values and limits appearing in standard typeface are for TJ= 25°C.
Symbol
ΔVOUT
PSRR
IQ
Parameter
Conditions
EUP7965
Min
Typ
Max.
Output Voltage Tolerance
IOUT = 1mA
Line Regulation Error
VIN = (VOUT(nom)+0.5V) to 5.5V,
For 4.8 to 5.0 options
For all other options
Load Regulation Error
IOUT = 1mA to 150mA
Power Supply Rejection
Ratio
VIN=VOUT(nom)+1V, f = 1kHz,
IOUT=50mA*6
VEN=1.4V, IOUT = 0mA
For 4.8 to 5.0 options
For all other options
VEN = 1.4V, IOUT = 0 to 150mA
For 4.8 to 5.0 options
For all other options
VEN = 0.4V
100
85
165
150
155
140
0.06
250
200
1.5
IOUT = 1mA
0.5
2
IOUT = 50mA
25
35
IOUT = 100mA
50
70
IOUT = 150mA
75
100
Quiescent Current
Dropout Voltage
DS7965 Ver1.5 March. 2006
5
Unit
% of
VOUT(nom)
-2
2
-0.19
-0.1
0.19
0.1
%/V
0.005
%mA
0.0025
70
dB
µA
mV
EUP7965
Electrical Characteristics
Unless otherwise specified, all limits guaranteed for VIN= VOUT(nom) +0.5V, CIN=1µF, IOUT=1mA, COUT=1µF,
CBYPASS=0.01µF. Typical values and limits appearing in standard typeface are for TJ= 25°C.
Symbol
Parameter
Conditions
Min
EUP7965
Typ
Max.
Unit
ISC
Short Circuit Current Limit
Output Grounded (Steady State)
600
mA
TON
Turn-On Time
CBYPASS = 0.01µF
150
µs
Output Noise Voltage
BW = 10Hz to 100kHz,
COUT = 1µF
50
µVrms
VEN = 0.4 and VIN = 5.5
±1
nA
en
IEN
VIL
VIH
TSD
Maximum Input Current at
EN
Maximum Low Level Input
Voltage at EN
Minimum High Level Input
Voltage at EN
Thermal Shutdown
Temperature
Thermal Shutdown
Hysteresis
DS7965 Ver1.5 March. 2006
VIN = 2.5 to 5.5V
VIN = 2.5 to 5.5V
6
0.4
1.4
V
V
160
°C
20
°C
EUP7965
Typical Operating Characteristics
Unless otherwise specified, CIN=CCOUT=1µF Ceramic, CBYPASS=10nF, VIN=VOUT+0.2V, TA=25°C, Enable pin is
tied to VIN.
DS7965 Ver1.5 March. 2006
7
EUP7965
DS7965 Ver1.5 March. 2006
8
EUP7965
DS7965 Ver1.5 March. 2006
9
EUP7965
DS7965 Ver1.5 March. 2006
10
EUP7965
DS7965 Ver1.5 March. 2006
11
EUP7965
Application Note
External Capacitors
Like any low-dropout regulator, the EUP7965 requires
external capacitors for regulator stability. The EUP7965
is specifically designed for portable applications
requiring minimum board space and smallest components.
These capacitors must be correctly selected for good
performance.
Input Capacitor
An input capacitance of ≈ 1µF is required between the
EUP7965 input pin and ground (the amount of the
capacitance may be increased without limit).
This capacitor must be located a distance of not more
than 1cm from the input pin and returned to a clean
analog ground. Any good quality ceramic, tantalum, or
film capacitor may be used at the input.
If a tantalum capacitor is used at the input, it must be
guaranteed by the manufacturer to have a surge current
rating sufficient for the application.
There are no requirements for the ESR on the input
capacitor, but tolerance and temperature coefficient must
be considered when selecting the capacitor to ensure the
capacitance will be ≈ 1µF over the entire operating
temperature range.
Output Capacitor
The EUP7965 is designed specifically to work with very
small ceramic output capacitors. A ceramic capacitor
(temperature characteristics X7R, X5R, Z5U, or Y5V) in
1 to 22µF range with 5mΩ to 500mΩ ESR range is
suitable in the EUP7965 application circuit.
The output capacitor must meet the requirement for
minimum amount of capacitance and also have an ESR
(Equivalent Series Resistance) value which is within a
stable range (5mΩ to 500mΩ)
No-Load Stability
The EUP7965 will remain stable and in regulation with
no external load. This is specially important in CMOS
RAM keep-alive applications.
Capacitor Characteristics
The EUP7965 is designed to work with ceramic
capacitors on the output to take advantage of the benefits
they offer: for capacitance values in the range of 1µF to
4.7µF range, ceramic capacitors are the smallest, least
expensive and have the lowest ESR values (which makes
them best for eliminating high frequency noise). The
ESR of a typical 1µF ceramic capacitor is in the range of
20mΩ to 40mΩ, which easily meets the ESR requirement
for stability by the EUP7965.
The ceramic capacitor’s capacitance can vary with
temperature. The capacitor type X7R, which operates
over a temperature range of -55°C to +125°C, will only
vary the capacitance to within ±15%. Most large value
ceramic capacitors ( ≈ 2.2µF) are manufactured with Z5U
or Y5V temperature characteristics. Their capacitance
can drop by more than 50% as the temperature goes from
25°C to 85°C. Therefore, X7R is recommended over Z5U
and Y5V in applications where the ambient temperature
will change significantly above or below 25°C.
Noise Bypass Capacitor
Connecting a 0.01µF capacitor between the CBYPASS pin
and ground significantly reduces noise on the regulator
output. This cap is connected directly to a high
impedance node in the bandgap reference circuit. Any
significant loading on this node will cause a change on
the regulated output voltage. For this reason, DC leakage
current through this pin must be kept as low as possible
for best output voltage accuracy. The types of capacitors
best suited for the noise bypass capacitor are ceramic and
film.
Unlike many other LDO’s , addition of a noise reduction
capacitor does not effect the load transient response of
the device.
On/Off Input Operation
The EUP7965 is turned off by pulling the VEN pin low,
and turned on by pulling it high. If this feature is not used,
the VEN pin should be tied to VIN to keep the regulator
output on at all time. To assure proper operation, the
signal source used to drive the VEN input must be able
to swing above and below the specified turn-on/off
voltage thresholds listed in the Electrical Characteristics
section under VIL and VIH.
Fast Start up
The EUP7965 output starts up after Vref voltage reaches
its final value (1.23V nomial). The start-up time is
determined by the time constant of the bypass capacitor.
The smaller the capacitor value., the shorter the start-up
time, but less noise gets reduced. As a result, start-up
time and noise reduction need to be taken into design
consideration when choosing the value of the bypass
capacitor.
DS7965 Ver1.5 March. 2006
12
EUP7965
Adjustable Operation
The adjustable version of the EUP7965 has an output
voltage range of 1.25V to 5V. The output voltage of the
EUP7965 adjustable regulator is programmed using an
external resistor divider as shown in Figure3. The output
voltage is calculated using:
VO = Vref × (1 +
R1
)
R2
Where:
Vref=1.23V typ. (the internal reference voltage)
Utilize the following equation for adjusting the output to
a particular voltage:
 V

PI = R  O − 1
2 1.23V


Choose R2=100k to optimize accuracy, power supply
rejection, noise and power consumption.
In order to improve the stability of the adjustable version,
it is suggested that a small compensation capacitor C1 be
placed between VOUT and SET .
DS7965 Ver1.5 March. 2006
13
EUP7965
Packaging Information
SOT23-5
Note:
1. Package body sizes exclude mold flash protrusions or gate burrs.
2. Tolerance ± 0.1000mm (4 mil) unless otherwise specified.
3. Coplanarity: 0.1000mm
4. Dimension L is measured in gage plane.
Symbols
A
A1
A2
b
C
D
E
e
H
L
θ1
DS7965 Ver1.5 March. 2006
Min.
1.00
0.00
0.70
0.35
0.12
2.70
1.50
----2.6
0.37
14
Dimension in Millimeters
Nom
1.10
----0.80
0.40
0.15
2.90
1.60
1.90(Typ.)
2.8
----5
14
Max.
1.30
0.10
0.90
0.50
0.20
3.10
1.70
----3.00
----9
EUP7965
SOT23-6
SYMBOLS
A
A1
A2
b
C
D
E
E1
e
E1
L
L1
L2
R
R1
θ
θ1
DS7965 Ver1.5 March. 2006
DIMENSIONS IN MILLIMETERS
MIN.
NOM.
--------------------0.90
1.15
0.30
-----0.08
-----2.90 BSC
2.80 BSC
1.60 BSC
0.95 BSC
1.90 BSC
0.30
0.45
0.60 REF
0.25 BSC
0.10
-----0.10
-----0°
4°
5°
10°
15
MAX.
1.45
0.15
1.30
0.50
0.22
0.60
-----0.25
8°
15°