EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Full Color Chip LED (Chip LED with Right Angle Lens) 12-23A/R6GHBHC-A01/2D Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Full-color type. ․Pb Free ․The product itself will remain within RoHS compliant version. Descriptions ․The 12-23A SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Automotive: backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Type Material Emitted Color R6 AlGaInP Brilliant Red GH InGaN Brilliant Green BH InGaN Blue Lens Color Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 1 of 12 Device No:DSE-123-004 Prepared date: 07-26-2005 Prepared by: Jeff Tasi EVERLIGHT ELECTRONICS CO.,LTD. 12-23A/R6GHBHC-A01/2D Package Outline Dimensions Note: The tolerances unless mentioned is ±0.1mm , Angle±0.5°,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 2 of 12 Device No:DSE-123-004 Prepared date: 07-26-2005 Prepared by: Jeff Tasi EVERLIGHT ELECTRONICS CO.,LTD. 12-23A/R6GHBHC-A01/2D Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V R6:25 Forward Current IF GH:25 mA BH:25 Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol 260 (for 5 seconds) ℃ R6:2000 Electrostatic Discharge ESD GH:150 V BH:150 R6:60 Power Dissipation Pd GH:110 mW BH:110 Peak Forward Current (Duty 1/10 @1KHz) R6:60 IF (Peak) GH:100 mA BH:100 Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 3 of 12 Device No:DSE-123-004 Prepared date: 07-26-2005 Prepared by: Jeff Tasi EVERLIGHT ELECTRONICS CO.,LTD. 12-23A/R6GHBHC-A01/2D Electro-Optical Characteristics (Ta=25℃) Parameter Symbol R6 Luminous Intensity Iv GH BH Viewing Angle 2θ1/2 Min. Typ. Max. Unit Condition 57 112 45 90 180 72 ----- mcd IF=20mA ----- 120 ----- deg IF=20mA ----- nm IF=20mA ----- nm IF=20mA ----- nm IF=20mA BH 632 518 468 624 525 470 R6 20 R6 Peak Wavelength λp GH ----- BH R6 Dominant Wavelength Spectrum Radiation Bandwidth Forward Voltage λd GH △λ GH VF ----- ----- 35 BH 35 R6 2.0 3.5 3.5 2.4 3.9 3.9 V IF=20mA ----- 10 50 50 μA VR=5V GH ----- BH R6 Reverse Current IR GH ----- BH Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm 3.Tolerance of Forward Voltage ±0.1V Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 4 of 12 Device No:DSE-123-004 Prepared date: 07-26-2005 Prepared by: Jeff Tasi EVERLIGHT ELECTRONICS CO.,LTD. 12-23A/R6GHBHC-A01/2D Typical Electro-Optical Characteristics Curves R6 Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 5 of 12 Device No:DSE-123-004 Prepared date: 07-26-2005 Prepared by: Jeff Tasi EVERLIGHT ELECTRONICS CO.,LTD. 12-23A/R6GHBHC-A01/2D Typical Electro-Optical Characteristics Curves GH Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 6 of 12 Device No:DSE-123-004 Prepared date: 07-26-2005 Prepared by: Jeff Tasi EVERLIGHT ELECTRONICS CO.,LTD. 12-23A/R6GHBHC-A01/2D Typical Electro-Optical Characteristics Curves BH Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 7 of 12 Device No:DSE-123-004 Prepared date: 07-26-2005 Prepared by: Jeff Tasi EVERLIGHT ELECTRONICS CO.,LTD. 12-23A/R6GHBHC-A01/2D ■ Label explanation CAT: Luminous Intensity (mcd) HUE: Dom. Wavelength (nm) REF: Forward Voltage (V) ■ Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm , Angle±0.5°,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 8 of 12 Device No:DSE-123-004 Prepared date: 07-26-2005 Prepared by: Jeff Tasi EVERLIGHT ELECTRONICS CO.,LTD. 12-23A/R6GHBHC-A01/2D ■ Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm , Angle±0.5°,Unit = mm ■ Moisture Resistant Packaging Label Aluminum moistue-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 9 of 12 Device No:DSE-123-004 Prepared date: 07-26-2005 Prepared by: Jeff Tasi EVERLIGHT ELECTRONICS CO.,LTD. 12-23A/R6GHBHC-A01/2D Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level : 90 % LTPD : 10 % Test Sample No. Items Test Condition Hours/Cycles Size Temp. : 240℃±5℃ 6 min. 1 Reflow 22 Pcs. Min. 5 sec. H : +100℃ 15min. 300 Cycles 2 Temperature Cycle 22 Pcs. ∫ 5 min. L : -40℃ 15min. 3 4 5 Thermal Shock High Temperature Storage Low Temperature Storage Ac/Rc 0/1 0/1 H : +100℃ 5min. ∫ 10 sec. L : -10℃ 5min. 300 Cycles 22 Pcs. 0/1 Temp. : 100℃ 1000 Hrs. 22 Pcs. 0/1 Temp. : -55℃ 1000 Hrs. 22 Pcs. 0/1 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 Pcs. 0/1 7 High Temperature / High Humidity 85℃/R.H85% 1000 Hrs. 22 Pcs. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 10 of 12 Device No:DSE-123-004 Prepared date: 07-26-2005 Prepared by: Jeff Tasi EVERLIGHT ELECTRONICS CO.,LTD. 12-23A/R6GHBHC-A01/2D Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Lead solder temperature profile 3.2 Lead free solder Lead solder temperature profile 3.3 Reflow soldering should not be done more than two times. 3.4 When soldering, do not put stress on the LEDs during heating. 3.5 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 11 of 12 Device No:DSE-123-004 Prepared date: 07-26-2005 Prepared by: Jeff Tasi EVERLIGHT ELECTRONICS CO.,LTD. 12-23A/R6GHBHC-A01/2D 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. http://www.everlight.com Rev 2 Page: 12 of 12 Device No:DSE-123-004 Prepared date: 07-26-2005 Prepared by: Jeff Tasi