EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 0.8mm Height Flat Top LED 17-215SURC/S530-XX/TRXX Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb-free. ․The product itself will remain within RoHS compliant version. Descriptions ․The 17-215 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Automotive: backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. ․Indoor signboard use. Device Selection Guide Chip Material Emitted Color AlGaInP Hyper Red Lens Color Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-175-004 Prepared date: 07-27-2005 Rev.2 Page: 1 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 17-215SURC/S530-XX/TRXX Package Outline Dimensions - + Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-175-004 Prepared date: 07-27-2005 Rev.2 Page: 2 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 17-215SURC/S530-XX/TRXX Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +90 ℃ Soldering Temperature Tsol Electrostatic Discharge ESD 2000 V Power Dissipation Pd 60 mW IFP 160 mA Peak Forward Current (Duty 1/10 @1KHz) 260 (for 5 ℃ seconds) Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-175-004 Prepared date: 07-27-2005 Rev.2 Page: 3 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 17-215SURC/S530-XX/TRXX Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Luminous Intensity Iv *Chip rank Min. Typ. Max. A2 ----- 2 ----- A3 ----- 3 ----- A4 ----- 4 ----- A5 ----- 5 ----- A6 ----- 6 ----- A2 13 32 ----- A3 31 46 ----- A4 42 63 ----- A5 51 78 ----- A6 61 94 ----- Unit Condition IF=2mA mcd Peak Wavelength λp ---- ---- 632 ----- nm Dominant Wavelength λd ----- ----- 624 ----- nm Spectrum Radiation Bandwidth △λ ----- ----- 20 ---- nm Viewing Angle 2θ1/2 ----- ----- 130 ---- deg Forward Voltage VF ----- ----- 2.0 2.4 V Reverse Current IR ---- ---- ---- 10 μA IF=20mA VR=5V *17-215SURC/S530-XX/TRXX Chip Rank Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-175-004 Prepared date: 07-27-2005 Rev.2 Page: 4 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 17-215SURC/S530-XX/TRXX Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-175-004 Prepared date: 07-27-2005 Rev.2 Page: 5 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 17-215SURC/S530-XX/TRXX Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank xxxxxx xxxxxx REF: Forward Voltage Rank RoHS xxxxxxxxxxxx xxxx xxxxxxxx Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-175-004 Prepared date: 07-27-2005 Rev.2 Page: 6 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 17-215SURC/S530-XX/TRXX Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moistue-proof bag Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-175-004 Prepared date: 07-27-2005 Desiccant Label Rev.2 Page: 7 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 17-215SURC/S530-XX/TRXX Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/ 85% RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-175-004 Prepared date: 07-27-2005 Rev.2 Page: 8 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 17-215SURC/S530-XX/TRXX Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-175-004 Prepared date: 07-27-2005 Rev.2 Page: 9 of 10 Prepared by: Aihua hong EVERLIGHT ELECTRONICS CO.,LTD. 17-215SURC/S530-XX/TRXX 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : SZDSE-175-004 Prepared date: 07-27-2005 Rev.2 Page: 10 of 10 Prepared by: Aihua hong