EVERLIGHT 75-21UYOC-TR8

EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet Preliminary
Auto Focus LED (4.0mm Round Leadframe)
75-21UYOC/TR8
Features
․Package in 12mm tape on 7" diameter reels.
․Compatible with automatic placement equipment.
․EIA Std. package.
․Mono-color type.
․Pb-free.
․The product itself will remain within RoHS
compliant version.
Descriptions
․The 75-21 SMD taping is much
smaller than leaded components .
Thus enable smaller board size.
Higher packing density.
Reduced storage space and finally smaller
equipment to be obtained.
․Besides, light weight makes them
ideal for miniature applications.
․Furthermore by automation assembly
machines the accuracy is anticipated.
Applications
․Small indicator for indoor applications.
․Flat backlight for LCD, switches and symbols.
․Indicator and backlight in office equipment.
․Indicator and backlight for battery driven
equipment.
․Indicator and backlight for audio and video equipment.
․Backlighting in dashboards and switches.
․Telecommunication:indicator and backlighting in telephone and fax.
Device Selection Guide
Part No.
75-21UYOC/TR8
Chip
Material
Emitted Color
AlGaInP
Brilliant Orange
Resin Color
Water Clear
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1.1
Page: 1 of 9
Device No. :
Prepared date: 07-May-2007
Prepared by: Alex Chen
EVERLIGHT ELECTRONICS CO.,LTD.
75-21UYOC/TR8
Package Outline Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1.1
Page: 2 of 9
Device No. :
Prepared date: 07-May-2007
Prepared by: Alex Chen
EVERLIGHT ELECTRONICS CO.,LTD.
75-21UYOC/TR8
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
Reverse Voltage
VR
5
V
Forward Current
IF
50
mA
Peak Forward Current
(Duty 1/10 @1KHz)
IFP
100
mA
Power Dissipation
Pd
120
mW
Electrostatic Discharge(HBM)
ESD
2000
V
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +90
℃
Soldering Temperature
Tsol
Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Luminous Intensity
Iv
10.0
15.0
----
cd
Viewing Angle
2θ1/2
----
15
----
deg
Peak Wavelength
λp
----
611
----
nm
Condition
IF=20mA
Dominant Wavelength
λd
600
----
610
nm
Spectrum Radiation
Bandwidth
△λ
----
17
----
nm
Forward Voltage
VF
1.7
----
2.4
V
Reverse Current
IR
----
----
10
μA
VR=5V
Notes:
1.Tolerance of Luminous Intensity ±11%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.05V
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1.1
Page: 3 of 9
Device No. :
Prepared date: 07-May-2007
Prepared by: Alex Chen
EVERLIGHT ELECTRONICS CO.,LTD.
75-21UYOC/TR8
Typical Electro-Optical Characteristics Curves
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1.1
Page: 4 of 9
Device No. :
Prepared date: 07-May-2007
Prepared by: Alex Chen
EVERLIGHT ELECTRONICS CO.,LTD.
75-21UYOC/TR8
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank
Reel Dimensions :
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1.1
Page: 5 of 9
Device No. :
Prepared date: 07-May-2007
Prepared by: Alex Chen
EVERLIGHT ELECTRONICS CO.,LTD.
75-21UYOC/TR8
Carrier Tape Dimensions : Loaded quantity 800 pcs per reel
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Moisture Resistant Packaging
Label
Aluminum moisture-proof bag
Desiccant
Label
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1.1
Page: 6 of 9
Device No. :
Prepared date: 07-May-2007
Prepared by: Alex Chen
EVERLIGHT ELECTRONICS CO.,LTD.
75-21UYOC/TR8
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level:90%
LTPD:10%
No.
Items
1
Reflow Soldering
2
Temperature Cycle
3
Thermal Shock
4
5
6
7
High Temperature
Storage
Low Temperature
Storage
DC Operating Life
High Temperature /
High Humidity
Test Condition
Test
Sample
Hours/Cycles
Size
Temp. : 260℃±5℃
Min. 5sec.
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
Temp. : 100℃
Temp. : -40℃
Ac/Re
6 Min.
22 PCS.
0/1
300 Cycles
22 PCS.
0/1
300 Cycles
22 PCS.
0/1
22 PCS.
0/1
22 PCS.
0/1
1000 Hrs.
1000 Hrs.
IF = 20 mA
1000 Hrs.
22 PCS.
0/1
85℃/ 85%RH
1000 Hrs.
22 PCS.
0/1
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1.1
Page: 7 of 9
Device No. :
Prepared date: 07-May-2007
Prepared by: Alex Chen
EVERLIGHT ELECTRONICS CO.,LTD.
75-21UYOC/TR8
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection, otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
1~5 °C / Sec.
260°C. Max.
10 Sec. Max.
1~5 °C / Sec.
Pre-heating
180~200°C
60 Sec. Max.
Above 220°C
120 Sec. Max.
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1.1
Page: 8 of 9
Device No. :
Prepared date: 07-May-2007
Prepared by: Alex Chen
EVERLIGHT ELECTRONICS CO.,LTD.
75-21UYOC/TR8
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of the
hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
Everlight Electronics Co., Ltd.
http://www.everlight.com
Rev.1.1
Page: 9 of 9
Device No. :
Prepared date: 07-May-2007
Prepared by: Alex Chen