X3DM Data sheet Pre-amplified/3V Excitation/Differential Features . . . . . Applications . Industrial instrumentation . Pressure switch, Pneumatic device 3V excitation, Battery operation available Very small surface mountable package, Easy to mount on PCB Volt level output On-chip amplification and temperature compensations Pre-calibration of offset voltage and span . Medical device Part number for ordering X3DM - 050KP D S R Terminal leads direction (See Outline Diagram) R: Model X3DM Rated pressure (Pa) Terminal leads configuration S : Surface mount package Pressure type D : Differential DW : Differential (Bipolar pressure) Pressure type Differential pressure X3DM Model Package configuration Surface mount package Measurable pressure range (kPa) 100 100 0 50 0 100 0 200 0 1000 Part number for ordering X3DM-100KPDWSR X3DM-050KPDSR X3DM-100KPDSR X3DM-200KPDSR X3DM-001MPDSR Specifications Model/Rated pressure 100KPDW 050KPD Recommended operating conditions Pressure type Rated pressure 100 1.020 100 100 50 0.510 0 50 100KPD Differential pressure 100 1.020 0 100 Non-corrosive gas only 3.0 0.15 200KPD 001MPD Unit 200 2.040 0 200 1000 10.20 0 1000 kPa kg/cm2 kPa Measurable pressure range Pressure media Excitation voltage Absolute maximum rating Maximum load pressure Twice of rated pressure Maximum excitation voltage 6 Operating temperature 10 80 Storage temperature 20 100 Operating humidity 30 80 (No dew condensation) Electric performances/characteristics(Excitation voltage Vcc=3.0V constant, Ambient temperature Ta=25 ) Current consumption less than 6 Output impedance less than 10 Source current less than 0.1 Sink current less than 1 Mechanical response time 2 (For the reference) Full scale span voltage 1.5 Offset voltage 1, 2 0.5 0.075 Full scale span voltage 1, 2 2.0 0.075 Accuracy 2 5.0 Note ; 1) Output refers to pressure at pressure port 2. 2) Excluding input voltage error. 1 VDC 1.5times of rated pressure VDC RH mA mA mA msec V V V FS/0 50 X3DM Data sheet Pre-amplified/3V Excitation/Differential Outline dimensions Unit : mm 0.15 5 Projections 4 Pressure port 2 4 5 6 0.5 Pressure port 1 15 6 10 M Labelled faceplate ax 8 3.5 2 2 2.54 6 0.8 3 1 3 1 1 3.3 2.5 17.5 11 14 R0.5 2 1 1 10 M 2.54 ax. Recommended footprint for PCB 2- 1.2(Holes for projections) Index direction 1.4 0.9 0.6 3.5 1 5.5 0.5 5 (11.5) 2 2.54 2.54 X3DM 1 Land-pads (Unit : mm) Zooming up the projections 3.4 11 16.6 Index Connection diagram Vcc(DC3V) X3DM Vcc Vout Vout GND C2 C1 GND Remarks : 1) C1 : Connect 680pF capacitor within 2cm distance from leads. 2) C2 : Connect 0.01 F or more capacitor within 2cm distance from leads. 3) 4 and 5 pins must be No Connection. Open them as floating ones completely, and do NOT connect to other line or each other. Transfer Function Vout=Vs (P + ) (Pressure Error Temperature Error Multiplier Vs) Vs=3.0volts Notes ; The output voltage (Vout) is no perfect ratiometric with the power supply voltage. P=Input Pressure(kPa) Model pressure range Temperature Error Multiplier=1 050KPG(D) 100KPG(D) 100KPGV 100KPGW(DW) 200KPG(D) 001MPGW(D) 115KPA 0 50kPa 0 100kPa 0 100kPa 0 +100kPa 0 200kPa 0 +1MPa 15 115kPa.abs 0.01 0.005 0.005 0.0025 0.0025 0.0025 0.005 Note ; Please read instruction “Notes” before using the sensor. Fujikura reserves the right to change specifications without notice. If you have any questions regarding technical issues or specifications, please contact us. Sensor Engineering Department 5-1 Kiba 1-chome, Koto-ku, Tokyo 135-8512, Japan Phone +81-(0)3-5606-1072 Fax. +81-(0)3-5606-1538 2 E-mail : [email protected] 0.1667 0.1667 0.1667 0.4667 0.1667 0.1667 0.09167 Pressure Error(kPa) 2.5 5.0 5.0 10.0 10.0 50.0 5.0