ETC UFL-2LP-066-A

SMT Ultra-Miniature Coaxial Connectors - Mating Heights Owing to the Lowest Profile and the Lightest
U.FL Series
Meets up to 6 GHz Requirement
3.2Max
2.4(2.5Max)
Figure 1. Mating Height Comparison
(with Hirose Electric Products)
U.FL
■Features
1. Mating Heights Owing to Lowest Profile
E.FL
●Space Factor of Mated Connector
Figure 2. U.FL-LP-040 and U.FL-R-SMT
Height from the printed circuit board when mates a receptacle with
a (right-angle) plug is 2.5 mm maximum. This low Profile is at the
world’s shortest level.
2. Extremely Small Board Occupation Area
These are the world’s lightest coaxial connectors.
Receptacle: 15.7 mg
Right-angle plugs
For Ø 0.81 mm cable: 53.7 mg
For Ø 1.13 & 1.32 mm cable: 59.1 mg
U.FL-LP-040
Dia.0.81
3. World’s Lightest
U.FL-R-SMT
2.5Max
In comparison with our E.FL Series of SMT coaxial connectors, the
receptacles offer a reduction of approximately 18% of the board
occupation area resulting in an area of just 7.7 mm2.
4. Can Be Used Up to a Frequency of 6 GHz
To meet the frequency requirements of a wide variety of miniature
equipment, these connectors offer high frequency performance
from DC to 6 GHz.
Figure 3. U.FL-LP-066and U.FL-R-SMT
5. Can Be Used with Automatic Mounting
The embossed tape packaging specification of the receptacles
permits automatic mounting.
U.FL-R-SMT
U.FL-LP-066
2.5Max
From among the types of suitable cable, Ø 0.8 mm (single shield)
outside diameter ultra-fine Teflon coaxial cable has been made a
standard specification in consideration of improving the
construction qualities and construction area.
An external diameter Ø1.32 mm (double shield) & Ø1.13mm (single
shield) ultra-fine Teflon coaxial cable specification is also available.
Dia.1.13
Dia.1.32
6. Use of Ultra-Fine Teflon Cable
7. Simple Removal of Connectors
The extraction jig permits simple removal of connectors.
8. Mating Checks Are Easy
Subminiature size notwithstanding, the lock sensation permits a
check of sure mating.
■Applications
Mobile phones, wireless communications
equipment, electronic measuring instruments,
GPS, wireless LAN, Bluetooth etc.
2002.3
1
■ Product Specifications
Nominal characteristic impedance
Rated voltage
Rated frequency
Ratings
Item
50ø
60 V AC (rms)
DC to 6 GHz
Operating temperature range
Operating humidity
-40˚C to +90˚C
90% max.
Conditions
Specification
1. Contact resistance
Center: 20 mø max.
Outside: 10 mø max.
Measured at 10 mA max.
2. Insulation resistance
500 Mø min.
Measured at 100 V DC
3. Withstand voltage
No line or insulation breakdown
4. V.S.W.R.*
200 V AC for 1 minute
1.3 max.
DC to 3 GHz
Dia.0.81Cable
1.35
Dia.1.13Cable
1.4
Dia.1.32Cable
1.5
5. Female contact holding force 0.15 N min.
3 to 6 GHz
Measured with a Ø 0.475 pin gauge
25 mø max. (Center)
15 mø max. (Outside)
6. Repetitive operation
Contact resistance
7. Vibration
No momentary disconnections of 1 µs min.
No damage, cracks, or parts looseness min.
Frequency of 10 to 100 Hz, single amplitude of 1.5 mm,
acceleration of 59 m/s2, for 5 cyles in the direction of each of the 3 axes
8. Shock
No momentary disconnections of 1 µs min.
No damage, cracks, or parts looseness
Acceleration of 735 m/s2, 11 ms duration, sine half-wave
waveform, for 6 cycles in the direction of each of the 3 axes
9. Humidity resistance
9. (Steady state)
No damage, cracks, or parts looseness
Insulation resistance 100 Mø min.(High temperature)
Insulation resistance 500 Mø min.(Pry)
Temperature of 40˚C, humidity of 95%,
let stand for 96 hours
10. Temperature cycle
No damage, cracks, or parts looseness
Contact resistance 25 mø max. (Center)
15 mø max. (Outside)
Temperature: +40˚C / 5 to 35˚C
/ +90˚C / 5 to 35˚C
Time:
30 min. / Within 5 min. / 30 min. / Within 5 min.
Cycles: 5
11. Salt spray test
No excessive corrosion
48 hours continuous exposure to 5% salt water
30 cycles of insertion and disengagement
*V.S.W.R. Measurement System
The above V.S.W.R. standard values were measured using the measurement system of the diagram below.
NOTE 1: Cable type connectors were measured with SMA conversion adapters
attached to both ends of the harness product of a suitable 100cm cable.
NOTE 2: Board type connectors were mounted to a 50Ω glass epoxy board and
measurements were conducted with SMA conversion adapters attached.
■Materials
Part
Material
Finish
Shell
Phosphor bronze
Silver plating
—————
Male center contact
Brass
Gold plating
—————
Phosphor bronze
Gold plating
—————
Plug
PBT
Black
UL94V-0
Receptacle
LCP
Beige
UL94V-0
Female center contact
Insulator
2
Remarks
■Plugs
U.FL-LP-040
Form of Plug After Cable Wiring
U.FL-LP-066
Form of Plug After Cable Wiring
Item
Right-angle plug shell
(for Ø 0.81 cable)
HRS No.
Part No.
Applicable Cable
CL331-0451-2
U.FL-LP-040
Weight (mg)
RF-MF5010 Manufactured by Nissei Electric Co., Ltd.
J12B0964 Manufactured by Junkosha Co., Ltd.
CO-6F-SB-CX50 Manufactured by Hitachi Cable, Ltd.
Right-angle plug shell
(for Ø 1.13 cable)
53.7/unit
RF-MF5016 Manufactured by Nissei Electric Co., Ltd.
J12B1054 Manufactured by Junkosha Co., Ltd.
CL331-0452-5
59.1/unit
U.FL-LP-066
Right-angle plug shell
(for Ø 1.32 cable)
A12B0733 Manufactured by Junkosha Co., Ltd.
CO-6F-DSB-CX-50 Manufactured by Hitachi Cable, Ltd.
Please order plugs with the cable assembly specifications.
■Cable Assembly
Dimension of U.FL Series assembly products should be made as indicated below.
Double-Ended Cable Assembly
Single-Ended Cable Assembly
●Cable Assembly Overall Length Standard Tolerance
●Ordering Information
U.FL - [] LP - [] - A - (L)
1
2
1 Series name
2 Assembly type
3 Cable type
4 Overall length (mm)
3
Overall Length L (mm)
0035<
=L<
=0200
4
Standard Tolerance (mm)
±04
0200<L<
=0500
<
0500<L=1000
U.FL
Blank: Single ended
2: Double ended
04 : For use with Ø 0.81 cable
5016 : For use with Ø 1.13 cable
066 : For use with Ø 1.32 cable
±08
±12
1000<L<
=1000
±1.5%
Note: Shortest length L is 35 mm.
Length L is expressed in mm units.
Part No. of Cable Assembly
U.FL-2LP-04-A-(L)
U.FL-LP-04-A-(L)
U.FL-2LP-5016-A-(L)
U.FL-LP-5016-A-(L)
U.FL-2LP-066-A-(L)
U.FL-LP-066-A-(L)
CL No.
321-1937-2**
321-1998-7**
321-2493-6**
321-2492-3**
321-2170-7**
321-2573-3-
**
Description
Dia. 0.81mm Double Ended Cable Assembly
Dia. 0.81mm Single Ended Cable Assembly
Dia. 1.13mm Double Ended Cable Assembly
Dia. 1.13mm Single Ended Cable Assembly
Dia. 1.32mm Double Ended Cable Assembly
Dia. 1.32mm Single Ended Cable Assembly
Please contact Hirose Sales Representative about cable length and cable end treatment.
3
(Note 3)
■Receptacles
NOTE 1: Receptacles of the (01) specification are sold by
the pack with 100 pieces per pack. Please order
in pack units.
NOTE 2: Receptacles of the (10) specification are sold by
the reel (which contains 2,500 pieces). Please
order in reel units.
NOTE 3: Permissible value for mold resin which gets onto
the center contact.
Recommended PCB Footprints
HRS No.
Part No.
Sales Quantity
CL331-0471-0-01
U.FL-R-SMT(01)
Pack sales (100 pieces per pack)
Weight (mg)
CL331-0471-0-10
U.FL-R-SMT(10)
Reel sales (2,500 pieces per reel)
15.7/unit
●Packaging Specifications
Embossed Carrier Tape Dimensions
Unreeling direction
Reel Dimensions
4
■Conversion Adapter
●SMA Conversion Adapter
(Coupling portion: U.FL side jack - SMA side plug)
NOTE: The U.FL side coupling portion has a weaker lock than
the regular product and, therefore, cannot be used for
purposes other than performance measurements.
HRS No.
Product No.
CL311-0300-2
HRMP-U.FLJ
HRS No.
Product No.
CL311-0301-5
HRMJ-U.FLP
HRS No.
Product No.
CL331-0466-0
U.FL-R-1
●SMA Conversion Adapter
(Coupling portion: U.FL side plug - SMA side jack)
NOTE: The U.FL side coupling portion has a weaker lock than
the regular product and, therefore, cannot be used for
purposes other than performance measurements.
■Inspection Receptacle
This receptacle is used for inspecting the continuity,
withstand voltage, and other aspects of the harness
product.
NOTE: The U.FL side coupling portion does not have a lock
and, therefore, cannot be used for purposes other than
continuity and withstand voltage inspections.
■Extraction Jig
This jig is used for extraction from a coupled condition.
90
Ø15
5
50
U.FL
2.1
U.FL-LP-N-2
HRS No.
Product No.
CL331-0494-5
U.FL-LP-N-2
CL331-0441-9
E.FL-LP-N-2
5
■Usage Precautions
1. Plugs
(1) Connection/
disconnection of
connectors
1) To disconnect connectors, hook the end portion of E.FL-LP-N and U.FL-LP-N-2 onto the connector cover and pull off
vertically in the direction of the connector coupling axis.
1) To remove the connector directly, hold the connector cover and pull off
U.FL-LP-N-2
vertically in the direction of the connector coupling axis. (Please exercise
E.FL-LP-N
caution so as not to injure fingertips or nails.)
U.FL-LP-040
U.FL-LP-066
2) To couple the connectors, the coupling axes of both connectors are
aligned and the connectors are inserted as perpendicularly as possible.
Do not attempt to insert on an extreme angle.
U.FL-R-SMT
After the connectors are coupled, do not apply a load to the cable in excess of the values indicated in the diagram
below.
U.FL-LP-040
(2) Permissible load on
the cable after
connector coupling.
2N or less
U.FL-R-SMT
4N or less
2N or less
(3) Precautions
Please note that excessive twisting in the action of insertion or removal will cause damage.
2. Receptacles
Recommended Temperature Profile (Reference)
(1) Recommended
temperature profile
(Reference)
1) The temperature indicates the printed circuit board surface temperature of the connector lead portion.
2) The reflow soldering method should be performed at a peak temperature of 240˚C or less at the surface of the
printed circuit board.
3) The temperature profile will change depending on conditions which include such factors as the size of the board,
the solder used, and the solder thickness.
(2) Recommended hand
soldering conditions
(Reference)
Soldering iron temperature: 350˚C
Soldering time: Within 5 seconds
(3) Recommended screen
0.15 mm
thickness
6