KIC3210T-025 ~ KIC3210T-035 SEMICONDUCTOR TECHNICAL DATA CMOS Linear Integrated Circuit 150mA CMOS High Performance LDO Regulator The KIC3210T series Low Dropout Linear Regulator is ideally suited for E portable applications. It offers 1% initial accuracy, extremely-low dropout B voltage(135mV at 150mA) and low ground current (typically 90uA). Designed 1 B F A The KIC3210T also works with low-ESR 3 D 4 ceramic capacitors, reducing the amount of board space necessary for power L C applications, critical in handheld wireless devices. I Features Input voltage range : 2.7V to 6.0V 1.6+0.2/-0.1 _ 0.05 0.70 + C 2 G consumption drops nearly to zero. G specifically for handheld and battery-powered devices, the KIC3210T provides a TTL-logic-compatible ON/OFF control pin. When disabled, power DIM MILLIMETERS _ 0.2 A 2.9 + 5 J H J Stability with ceramic output capacitors D _ 0.1 0.4 + E F G H I J K L 2.8+0.2/-0.3 _ 0.2 1.9 + 0.95 _ 0.05 0.16 + 0.00-0.10 0.25+0.25/-0.15 0.60 0.55 1 VIN 2 GND 3 ON/OFF Control Ultra-low dropout : 135mV @ 150mA 4 BYP High output accuracy : 1.0% accuracy 5 VOUT Low quiescent current : 90 A TTL-Logic-compatible ON/OFF control input Zero off-mode current Thermal shutdown and current limit protection TSV Applications Cellular phones,Smart Phones, PDA Battery-powered equipment Laptop, notebook and palmtop computers Marking Consumer/personal electronics 5 4 Lot No. Type Name 1 2006. 10. 24 Revision No : 3 2 3 1/5 KIC3210T-025 ~ KIC3210T-035 Line up Item Output Voltage Marking KIC3210T-025 2.5V KIC3210T-026 Package Item Output Voltage Marking 25A KIC3210T-030 3.0V 30A 2.6V 26A KIC3210T-031 3.1V 31A KIC3210T-027 2.7V 27A KIC3210T-032 3.2V 32A KIC3210T-275 2.75V 27B KIC3210T-033 3.3V 33A KIC3210T-028 2.8V 28A KIC3210T-034 3.4V 34A KIC3210T-285 2.85V 28B KIC3210T-035 3.5V 35A KIC3210T-029 2.9V 29A TSV Package TSV Pin Configuration OUT BYP No. Symbol 5 4 1 INPUT 2 GND 3 ON/OFF CONTORL Enable/Shutdown (Input) : CMOS compatible input. Logic high=enable, logic low=shutdown. Do not leave open. Reference Bypass : Connect external 0.01 F C BYP capacitor to GND to reduce output noise. May be left open. 1 2 3 4 BYP IN GND ON/OFF CONTROL 5 OUTPUT Description Supply Input Ground 1.0 F Regulator Output Application Circuit VIN 1 5 VOUT CIN=1.0µF Ceramic 2 Enable Shutdown ON/OFF CONTROL ON/OFF CONTROL(Pin 3) maybe connected directly to VIN (pin1) 2006. 10. 24 Revision No : 3 3 COUT=1.0µF Ceramic 4 CBYP=0.01µF 2/5 KIC3210T-025 ~ KIC3210T-035 Absolute Maximum Ratings Characteristics Symbol Rating Units Input Voltage VIN 6 V Output Current IOUT 150 mA Output Voltage VOUT 2.5~3.5 V Power DissipationNote PD 900 mW Operating Temperature TOPR -40 ~ 85 Storage Temperature TSTG -65 ~ 125 Note) Package Mounted on a Ceramic board (600 0.8 ) Electrical Characteristics (VIN=VOUT+1V, VEN=VIN, IOUT=100 , Ta=25 ) Parameter Symbol VO Output Voltage Accuracy Conditions Min Typ Max Units IOUT=100 A -1 - 1 % Load Regulation Reg Load IOUT=0.1mA ~ 150mA - 1.5 2.5 % Line Regulation Reg Line VIN=VOUT+1V ~ 6V - 0.1 0.2 %/V IOUT=100uA - 0.1 5 mV IOUT=100mA - 90 150 mV IOUT=150mA - 135 200 mV VEN= 0.4V (shutdown) - 0.2 1 A IOUT=0mA - 90 150 A IOUT=150mA - 117 150 A f=10Hz, COUT=1.0 F, CBYP=0.01 F - 60 - dB f=100Hz, VIN=VOUT+1 - 60 - dB f=10kHz, VIN=VOUT+1 - 50 - dB 160 425 - mA - 50 - Vrms 1.6 - - V VD Dropout Voltage Note 1) IQ Quiescent Current IGND Ground Pin Current Note 2) Ripple Rejection R.R Current Limit ILIM VOUT=0V Output Noise Voltage VNO COUT=1.0 F, CBYP=0.01 F f=10Hz ~ 100kHz Output Control Voltage (ON-State) VC(ON) VIN=2.7V ~ 5.5V, regulator enable Output Control Voltage (OFF-State) VC(OFF) VIN=2.7V ~ 5.5V, regulator shutdown - - 0.4 V VC 1.6V, regulator enable - 0.01 - A VC 0.4V, regulator shutdown - 0.01 - A TSD - 150 - TSD_HYS - 10 - IC Output Control Current Thermal Shutdown Temperature Thermal Shutdown Hysteresis Note 1) Dropout Voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. For outputs below 2.7V, dropout voltage is the input-to-output voltage differential with the minimum input voltage 2.7V Note 2) Ground pin current is the regulator quiescent current. The total current drawn from the supply is the sum of the load current plus the ground pin current. 2006. 10. 24 Revision No : 3 3/5 KIC3210T-025 ~ KIC3210T-035 Fig. 2 VIN - IGND Fig. 1 R.R GROUND CURRENT IGND (µA) 70 100µA* 60 50mA* R.R (dB) 50 150mA* 40 100mA* 30 20 10 0 *ILOAD COUT=1µF Ceramic 101 102 103 104 105 106 140 ILOAD = 100µA 120 100 80 60 40 20 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 FREQUENCY (Hz) INPUT VOLTAGE VIN (V) Fig. 4 Ta - VDROP 3.5 DROP VOLTAGE VDROP (mV) OUTPUT VOLTAGE VOUT (V) Fig. 3 VIN - VOUT 3.0 ILOAD =100µA 2.5 ILOAD =150mA 2.0 1.5 1.0 0.5 0 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0.14 0.12 0.1 0.8 0.6 0.4 0.2 0 -40 ILOAD = 100µA -20 0 3.05 3.04 3.03 3.02 3.01 3.00 2.99 2.98 2.97 ILOAD = 100µA -20 0 20 40 60 80 40 60 80 100 120 140 Fig. 6 Line Transient Response 100 120 140 OUTPUT VOLTAGE INPUT VOLTAGE (50mV/div) (1V/div) OUTPUT VOLTAGE VOUT (V) Fig. 5 Ta - VOUT 2.95 -40 20 TEMPERTURE Ta ( C) INPUT VOLTAGE VIN (V) 2.96 5.0 5V 4V CIN = 1µF Ceramic COUT = 1µF Ceramic CBYP = 0.01µF IOUT=100µA TIME (400µs/div) TEMPERTURE Ta ( C) 2006. 10. 24 Revision No : 3 4/5 Fig. 7 Load Transient Response 150mA CIN = 1µF Ceramic COUT = 1µF Ceramic CBYP = 0.01µF VIN = 4V 100mA TIME (4µs/div) OUTPUT VOLTAGE ENABLE VOLTAGE (1V/div) (1V/div) OUTPUT CURRENT OUTPUT VOLTAGE (100mV/div) (50mV/div) KIC3210T-025 ~ KIC3210T-035 Fig. 8 ON/OFF Control Pin Delay CIN = 1µF Ceramic COUT = 1µF Ceramic CBYP = 0.01µF IOUT=100µA TIME (10µs/div) OUTPUT VOLTAGE ENABLE VOLTAGE (1V/div) (1V/div) Fig. 9 Shutdown Delay 2006. 10. 24 CIN = 1µF Ceramic COUT = 1µF Ceramic CBYP = 0.01µF VIN = 4V TIME (400µs/div) Revision No : 3 5/5