KODENSHI KK74ACT257

TECHNICAL DATA
KK74ACT257
Quad 2-Input Data Selector/Multiplexer
with 3-State Outputs
High-Speed Silicon-Gate CMOS
The KK74ACT257 is identical in pinout to the LS/ALS257,
HC/HCT257. The KK74ACT257 may be used as a level converter for
interfacing TTL or NMOS outputs to High Speed CMOS inputs.
This device selects a (4-bit) nibble from either the A or B inputs as
determined by the Select input. The nibble is presented at the outputs in
noninverted from when the Output Enable pin is at a low level. A high
level on the Output Enable pin switches the outputs into the highimpedance state.
• TTL/NMOS Compatible Input Levels
• Outputs Directly Interface to CMOS, NMOS, and TTL
• Operating Voltage Range: 4.5 to 5.5 V
• Low Input Current: 1.0 µA; 0.1 µA @ 25°C
• Outputs Source/Sink 24 mA
ORDERING INFORMATION
KK74ACT257N Plastic
KK74ACT257D SOIC
TA = -40° to 85° C for all packages
PIN ASSIGNMENT
LOGIC DIAGRAM
FUNCTION TABLE
Inputs
PIN 16 =VCC
PIN 8 = GND
Outputs
Output
Enable
Select
Y0-Y3
H
X
Z
L
L
A0-A3
L
H
B0-B3
X=don’t care
Z = high-impedance state
A0-A3,B0-B3=the levels of the respective
Nibble Inputs
1
KK74ACT257
MAXIMUM RATINGS*
Symbol
Parameter
Value
Unit
-0.5 to +7.0
V
VCC
DC Supply Voltage (Referenced to GND)
VIN
DC Input Voltage (Referenced to GND)
-0.5 to VCC +0.5
V
DC Output Voltage (Referenced to GND)
-0.5 to VCC +0.5
V
DC Input Current, per Pin
±20
mA
IOUT
DC Output Sink/Source Current, per Pin
±50
mA
ICC
DC Supply Current, VCC and GND Pins
±50
mA
PD
Power Dissipation in Still Air, Plastic DIP+
SOIC Package+
750
500
mW
-65 to +150
°C
260
°C
VOUT
IIN
Tstg
TL
Storage Temperature
Lead Temperature, 1 mm from Case for 10 Seconds
(Plastic DIP or SOIC Package)
*
Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the Recommended Operating Conditions.
+Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C
SOIC Package: : - 7 mW/°C from 65° to 125°C
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
VIN, VOUT
DC Supply Voltage (Referenced to GND)
DC Input Voltage, Output Voltage (Referenced to GND)
TJ
Junction Temperature (PDIP)
TA
Operating Temperature, All Package Types
IOH
Output Current - High
IOL
Output Current - Low
tr, tf
*
Parameter
Input Rise and Fall Time
(except Schmitt Inputs)
*
Min
Max
Unit
4.5
5.5
V
0
VCC
V
140
°C
+85
°C
-24
mA
24
mA
10
8.0
ns/V
-40
VCC =4.5 V
VCC =5.5 V
0
0
VIN from 0.8 V to 2.0 V
This device contains protection circuitry to guard against damage due to high static voltages or electric fields.
However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this
high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≤(VIN or
VOUT)≤VCC.
Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused
outputs must be left open.
2
KK74ACT257
DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)
VCC
Symbol
Parameter
Test Conditions
Guaranteed Limits
V
25 °C
-40°C to
85°C
Unit
VIH
Minimum HighLevel Input Voltage
VOUT=0.1 V or VCC-0.1 V
4.5
5.5
2.0
2.0
2.0
2.0
V
VIL
Maximum Low Level Input Voltage
VOUT=0.1 V or VCC-0.1 V
4.5
5.5
0.8
0.8
0.8
0.8
V
VOH
Minimum HighLevel Output Voltage
IOUT ≤ -50 µA
4.5
5.5
4.4
5.4
4.4
5.4
V
4.5
5.5
3.86
4.86
3.76
4.76
4.5
5.5
0.1
0.1
0.1
0.1
VIN=VIH or VIL
IOL=24 mA
IOL=24 mA
4.5
5.5
0.36
0.36
0.44
0.44
±0.1
±1.0
µA
1.5
mA
±5.0
µA
*
VIN=VIH or VIL
IOH=-24 mA
IOH=-24 mA
VOL
Maximum LowLevel Output Voltage
IOUT ≤ 50 µA
V
*
IIN
Maximum Input
Leakage Current
VIN=VCC or GND
5.5
∆ICCT
Additional Max.
ICC/Input
VIN=VCC - 2.1 V
5.5
IOZ
Maximum ThreeState Leakage
Current
VIN (OE)= VIH or VIL
VIN =VCC or GND
VOUT =VCC or GND
5.5
IOLD
+Minimum Dynamic
Output Current
VOLD=1.65 V Max
5.5
75
mA
IOHD
+Minimum Dynamic
Output Current
VOHD=3.85 V Min
5.5
-75
mA
ICC
Maximum Quiescent
Supply Current
(per Package)
VIN=VCC or GND
5.5
80
µA
±0.5
8.0
*
All outputs loaded; thresholds on input associated with output under test.
+Maximum test duration 2.0 ms, one output loaded at a time.
3
KK74ACT257
AC ELECTRICAL CHARACTERISTICS (VCC=5.0 V ± 10%, CL=50pF, Input tr=tf=3.0 ns)
Guaranteed Limits
Symbol
Parameter
25 °C
-40°C to 85°C
Min
Max
Min
Max
Unit
tPLH
Propagation Delay, Nibble A or B to Output Y
(Figure 1)
1.5
7.0
1.0
7.5
ns
tPHL
Propagation Delay, Nibble A or B to Output Y
(Figure 1)
2.0
7.5
1.5
8.5
ns
tPLH
Propagation Delay, Select to Output Y
(Figure 2)
2.0
9.5
1.5
10.5
ns
tPHL
Propagation Delay, Select to Output Y
(Figure 2)
2.5
10.5
2.0
11.5
ns
tPZH
Propagation Delay, Output Enable to Output Y
(Figure 3)
2.0
8.0
1.5
9.0
ns
tPZL
Propagation Delay, Output Enable to Output Y
(Figure 3)
2.0
8.0
1.5
9.0
ns
tPHZ
Propagation Delay, Output Enable to Output Y
(Figure 3)
2.5
9.0
1.5
10.0
ns
tPLZ
Propagation Delay, Output Enable to Output Y
(Figure 3)
2.0
7.5
1.5
8.5
ns
CIN
Maximum Input Capacitance
4.5
4.5
pF
Typical @25°C,VCC=5.0 V
CPD
Power Dissipation Capacitance
Figure 1. Switching Waveforms
50
pF
Figure 2. Switching Waveforms
4
KK74ACT257
Figure 3. Switching Waveforms
EXPANDED LOGIC DIAGRAM
5
KK74ACT257
N SUFFIX PLASTIC DIP
(MS - 001BB)
A
Dimension, mm
9
16
Symbol
MIN
MAX
A
18.67
19.69
B
6.1
7.11
B
1
8
5.33
C
F
L
C
D
0.36
0.56
F
1.14
1.78
G
2.54
H
7.62
-T- SEATING
PLANE
N
G
K
M
H
D
J
0.25 (0.010) M T
NOTES:
1. Dimensions “A”, “B” do not include mold flash or protrusions.
Maximum mold flash or protrusions 0.25 mm (0.010) per side.
J
0°
10°
K
2.92
3.81
L
7.62
8.26
M
0.2
0.36
N
0.38
D SUFFIX SOIC
(MS - 012AC)
Dimension, mm
A
16
9
H
B
1
G
P
8
R x 45
C
-TK
D
SEATING
PLANE
J
0.25 (0.010) M T C M
NOTES:
1. Dimensions A and B do not include mold flash or protrusion.
2. Maximum mold flash or protrusion 0.15 mm (0.006) per side
for A; for B ‑ 0.25 mm (0.010) per side.
F
M
Symbol
MIN
MAX
A
9.8
10
B
3.8
4
C
1.35
1.75
D
0.33
0.51
F
0.4
1.27
G
1.27
H
5.72
J
0°
8°
K
0.1
0.25
M
0.19
0.25
P
5.8
6.2
R
0.25
0.5
6