MIMIX PB-CDQ6004-QS-00C0

0.05-4.0 GHz
Dual High Dynamic Range Amplifier
CDQ6004-QS
August 2007 - Rev 11-Aug-07
Features
Matched Pair of Amplifiers for Optimum Balanced Design
0.05 to 4.0 GHz Frequency Range
44 dBm Output IP3 (Balanced configuration)
41 dBm Output IP3 (Single-ended configuration)
15 dB Gain @ 2 GHz
23 dBm P1dBm
2.1 dB Noise Figure
RoHS Compliant 4X4 QFN Package
Single Positive Supply
+3V to +5V Voltage Rail
Absolute Maximum Ratings
General Description
The CDQ6004-QS is a dual high dynamic range amplifier designed
for applications operation within the 0.05 to 4.0 GHz frequency
range. Co-located matched amplifiers are assembled in the 4mm X
4mm QFN package. The low-cost, surface-mount, 16 terminal, plastic
package is RoHS compliant. The CDQ6004-QS is an ideal solution for
implementing balanced or push-pull designs. The amplifier can also
be used for dual-band operation where single-ended design is used
for each band. The amplifier has the flexibility of being optimized
for a number of wireless applications. The combination of low noise
figure and high IP3 at the same bias point make it an ideal transmit
or receive solution when used in applications including CATV
operating from 50 to 850 MHz, cellular and PCS (personal
communications service) operating from 0.8 to 2.2 GHz; MMDS
(multichannel multipoint distribution systems) operating from 2.2
to 2.7 GHz; and WLAN (wireless LAN) operation at 2.4 GHz. All
devices are 100% RF and DC tested.
Supply Voltage
RF Input Power
Storage Temperature (Tstg)
Junction Temperature
Operating Temperature
Thermal Resistance
+6.0 V
+20 dBm
-55 ºC to +125 ºC
150 ºC
-40 ºC to +85ºC
52 ºC/W
Operation of this device above any of these parameters may cause damage.
Typical Parameters
Electrical Characteristics (T = 25ºC)
Parameter
Typical
Frequency Range
Gain
Input Return Loss
Output Return Loss
Output IP3
Noise Figure
Output P1dB
Units
0.9
2
2.4
GHz
16.5
15
14.9
dB
-13
-11
-20
dB
-16
-12
-11
dB
42
41
40.5
dBm
2.1
2.1
2.6
dB
+23
+23
+24
dBm
Typical values reflect performance in recommended application circuit @ +5V.
Unless otherwise specified, the following specifications are guaranteed at room temerpature in a Mimix fixture.
Parameter
Frequency Range
Gain
Input Return Loss
Output Return Loss
Output IP3
Noise Figure
Output P1dB
Operating Current Range
Supply Voltage
Condition
Externally Matched
Externally Matched
Externally Matched
Units
GHz
dB
dB
dB
dBm
dB
dBm
mA
V
Min.
0.25
13.5
38
130
Typ.
15
-10
-10
41
2.1
23
160
5.0
Max.
3.0
200
Notes:
1. T = 25ºC, Frequency = 2 GHz, 50 Ohm system.
2. Each single ended amplifier is tested separately.
3. OIP3 is measured with two tones at output power of 5 dBm/tone separated by 10 MHz.
4. Slight performance degredation is expected over temperature.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 1 of 10
Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
0.05-4.0 GHz
Dual High Dynamic Range Amplifier
CDQ6004-QS
August 2007 - Rev 11-Aug-07
Typical Device S-Parameters
CDQ6004-QS
S21 Vs Voltage
CDQ6004-QS
S12 Vs Voltage
19
0
18
17
16
-5
15
S21 3V
S21 4V
S21 5V
14
13
S12 3V
S12 4V
S12 5V
-10
12
10
(dB)
(dB)
11
9
8
-15
7
-20
6
5
4
3
-25
2
1
0
0
1
2
3
4
5
6
7
8
9
-30
10
0
Frequency (GHz)
1
2
3
4
6
7
8
9
10
9
10
CDQ6004-QS
S11 Vs Voltage
CDQ6004-QS
S22 Vs Voltage
20
10
18
9
16
8
14
7
12
6
S22 3V
S22 4V
S22 5V
10
8
6
S11 3V
S11 4V
S11 5V
5
4
3
4
2
2
1
0
(dB)
(dB)
5
Frequency (GHz)
-2
-4
0
-1
-2
-6
-3
-8
-4
-10
-5
-12
-14
-6
-16
-7
-18
-8
-9
-20
0
1
2
3
4
5
6
Frequency (GHz)
7
8
9
10
-10
0
1
2
3
4
5
6
7
8
Frequency (GHz)
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 2 of 10
Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
0.05-4.0 GHz
Dual High Dynamic Range Amplifier
CDQ6004-QS
August 2007 - Rev 11-Aug-07
Application Circuit @ 900 MHz
Schematic:
Typical Performance:
CDQ6004-QS Evalua tio n B o ard @ 900MHz
VD=5 V
15
20
15
Gain
5
10
5
-5
0
Input Return Loss
-5
- 15
- 10
- 15
Output Return Loss
-2 0
0
0.5
1
-2 5
1. 5
2
F re q u e n c y ( G H z )
Parameter
Board Layout:
Frequency Range
Gain
Input Return Loss
Output Return Loss
Output IP3
Noise Figure
Output P1dB
Typical
Units
0.9
GHz
16.5
dB
-13
dB
-16
dB
42
dBm
2.1
dB
23
dBm
Components
Ref Designator
C2, C4, C6, C8
C1, C5
C3, C7
L1, L2
L3, L4
Value
Size
2.7 pf
0402
1.5 pf
0603
1000 pf
0805
47 nH
0805
6.8 nH
0603
* Material: FR4, 28 mil
* Plating: 1.5 oz. Copper both sides
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 3 of 10
Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
0.05-4.0 GHz
Dual High Dynamic Range Amplifier
CDQ6004-QS
August 2007 - Rev 11-Aug-07
Typical Performance @ 900 MHz (50 Ohm system over voltage)
CDQ6004-QS Evaluation Board @ 0.9GHz
Input Return Loss (S11) Over Voltage
20
18
16
14
12
10
8
6
4
2
0
Vd=2V
Vd=3V
Vd=4V
Vd=5V
Return Loss (dB)
Gain (dB)
CDQ6004-QS Evaluation Board @ 0.9GHz
Gain Over Voltage
0
-5
-10
-15
-20
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
0
0.5
1
1.5
Frequency (GHz)
Vd=5V
2
2.5
3
3.5
4
4.5
5
5.5
6
Frequency (GHz)
CDQ6004-QS Evaluation Board @ 900MHz
P1dB Over Voltage
CDQ6004-QS Evaluation Board @ 0.9GHz
Output Return Loss (S22) Over Voltage
26
0
24
-5
P1dB (dBm)
Return Loss (dB)
Vd=3V
Vd=4V
-25
0
-10
-15
Vd=2V
Vd=4V
-20
Vd=3V
Vd=5V
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
22
20
18
16
14
12
-25
5
5.5
1.5
6
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
5.0
5.5
Drain Voltage (V)
Frequency (GHz)
CDQ6004-QS Evaluation Board @ 900MHz
Noise Figure Over Voltage
CDQ6004-QS Evaluation Board @ 900MHz
OIP3 Over Voltage
2.4
44
42
40
38
36
34
32
30
28
26
24
2.2
NF(dB)
OIP3 (dBm)
Vd=2V
2.0
1.8
1.6
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
1.5
2.0
2.5
3.0
3.5
4.0
4.5
Drain Voltage (V)
Drain Voltage (V)
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 4 of 10
Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
0.05-4.0 GHz
Dual High Dynamic Range Amplifier
CDQ6004-QS
August 2007 - Rev 11-Aug-07
Application Circuit @ 1.9 GHz ~ 2.1 GHz:
Schematic:
Typical Performance:
CDQ6 004-QS Evalua tio n B o ard @ 1.9GHz 2.1GHz
VD=5 V
20
15
15
Gain
10
5
5
Input Return Loss
0
-5
-5
- 10
- 15
- 15
Output Return Loss
-2 0
0
0 .5
1.5
1
2
-2 5
3
2 .5
F re q u e n c y ( G H z )
Parameter
Frequency Range
Gain
Input Return Loss
Output Return Loss
Output IP3
Noise Figure
Output P1dB
Board Layout:
Typical
Units
1.9
2.1
GHz
15.3
15.0
dB
-11.9
-12.5
dB
-16.3
-13.6
dB
dBm
41
41.3
2.1
2.1
dB
23
23
dBm
Components
Ref Designator
C2, C4, C6, C8
C1, C5
C3, C7
L1, L2
Value
Size
100 pf
0402
1.5 pf
0603
1000 pf
0805
47 nH
0805
* Material: FR4, 28 mil
* Plating: 1.5 oz. Copper both sides
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 5 of 10
Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
0.05-4.0 GHz
Dual High Dynamic Range Amplifier
CDQ6004-QS
August 2007 - Rev 11-Aug-07
Typical Performance @ 1.9 GHz (50 Ohm system over voltage)
CDQ6004-QS Evaluation Board @ 1.9~2.1GHz
Input Return Loss (S11) Over Voltage
20
18
16
14
12
10
8
6
4
2
0
Vd=2V
Vd=3V
Vd=4V
Vd=5V
Return Loss (dB)
Gain (dB)
CDQ6004-QS Evaluation Board @ 1.9 ~ 2.1
Gain Over Voltage
0
-5
-10
-15
-20
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
0
0.5
1
1.5
Frequency (GHz)
Vd=5V
2
2.5
3
3.5
4
4.5
5
5.5
6
Frequency (GHz)
CDQ6004-QS Evaluation Board @ 1.9~2.1GHz
Output Return Loss (S22) Over Voltage
CDQ6004-QS Evaluation [email protected]
P1dB Over Voltage
0
26
24
-5
P1dB (dBm)
Return Loss (dB)
Vd=3V
Vd=4V
-25
0
-10
-15
Vd=2V
Vd=4V
-20
Vd=3V
Vd=5V
22
20
18
16
14
-25
12
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
1.5
2.0
2.5
Frequency (GHz)
3.0
3.5
4.0
4.5
5.0
5.5
5.0
5.5
Drain Voltage (V)
CDQ6004-QS Evaluation Board @ 1.9GHz
Noise Figure Over Voltage
CDQ6004-QS Evaluation Board @ 1.9GHz
OIP3 Over Voltage
2.4
44
42
40
38
36
34
32
30
28
26
24
2.2
NF (dB)
OIP3(dBm)
Vd=2V
2.0
1.8
1.6
1.5
2.0
2.5
3.0
3.5
4.0
Drain Voltage (V)
4.5
5.0
5.5
1.5
2.0
2.5
3.0
3.5
4.0
4.5
Drain Voltage (V)
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 6 of 10
Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
0.05-4.0 GHz
Dual High Dynamic Range Amplifier
CDQ6004-QS
August 2007 - Rev 11-Aug-07
Application Circuit @ 2.4 GHz:
Schematic:
Typical Performance:
CDQ6004-QS Evalua tio n B o ard @ 2 .4 GHz
VD=5V
15
20
15
10
5
Gain
5
Input Return Loss
-5
0
-5
Output Return Loss
- 10
- 15
- 15
-2 0
-2 5
0
0 .5
1
1.5
2
2 .5
3
3 .5
F re q u e n c y ( G H z )
Parameter
Frequency Range
Gain
Input Return Loss
Output Return Loss
Output IP3
Noise Figure
Output P1dB
Board Layout:
Typical
Units
2.4
GHz
14.9
dB
-20
dB
-11
dB
40.5
dBm
2.6
dB
24
dBm
Components
Ref Designator
C2, C4, C6, C8
C1, C5
C3, C7
L1, L2
Value
Size
2.7 pf
0402
1.2 pf
0603
1000 pf
0805
47 nH
0805
* Material: FR4, 28 mil
* Plating: 1.5 oz. Copper both sides
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 7 of 10
Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
0.05-4.0 GHz
Dual High Dynamic Range Amplifier
CDQ6004-QS
August 2007 - Rev 11-Aug-07
Typical Performance @ 2.4 GHz (50 Ohm system over voltage)
CDQ6004-QS Evaluation Board @ 2.4GHz
Input Return Loss (S11) Over Voltage
20
18
16
14
12
10
8
6
4
2
0
Vd=2V
Vd=3V
Vd=4V
Vd=5V
Return Loss (dB)
Gain (dB)
CDQ6004-QS Evaluation Board @ 2.4GHz
Gain Over Voltage
0
-5
-10
-15
Vd=2V
-20
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
0
0.5
1
1.5
Frequency (GHz)
2
2.5
3
3.5
4
4.5
5
5.5
6
Frequency (GHz)
CDQ6004-QS Evaluation Board @ 2.4GHz
Output Return Loss (S22) Over Voltage
CDQ6004-QS Evaluation Board @ 2.4GHz
P1dB Over Voltage
0
26
Output P1dB(dBm)
Return Loss (dB)
Vd=5V
-25
0
-5
-10
-15
Vd=2V
Vd=4V
-20
Vd=3V
Vd=5V
-25
24
22
20
18
16
14
12
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
1.5
2.0
2.5
Frequency (GHz)
3.0
3.5
4.0
4.5
5.0
5.5
5.0
5.5
Drain Voltage (V)
CDQ6004-QS Evaluation Board @ 2.4GHz
OIP3 Over Voltage
CDQ6004-QS Evaluation Board @ 2.4GHz
Noise Figure Over Voltage
2.8
48
46
44
42
40
38
36
34
32
30
28
26
24
22
2.6
NF(dB)
OIP3(dBm)
Vd=3V
Vd=4V
2.4
2.2
2.0
1.5
2.0
2.5
3.0
3.5
4.0
Drain Voltage (V)
4.5
5.0
5.5
1.5
2.0
2.5
3.0
3.5
4.0
4.5
Drain Voltage (V)
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 8 of 10
Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
0.05-4.0 GHz
Dual High Dynamic Range Amplifier
CDQ6004-QS
August 2007 - Rev 11-Aug-07
Functional Block Diagram
Pin Out Detail
Pin
Function Description
5
8
16
13
1,2,3,4
9,10,11,12
6,7,14,15
IN 1
Amplifier 1 RF Input
IN 2
Amplifier 2 RF Input
OUT 1
Amplifier 1 RF Output
OUT 2
Amplifier 2 RF Output
VS 1
Amplifier 1 Source Connection
VS 2
Amplifier 2 Source Connection
GND
Main Heat-Sinking Connection
Physical Dimensions
D
b
K
E2
WAFER LOT NUMBER
e
E
100% MATTE TIN
L
DATE CODE (YEAR/WEEK)
D2
COUNTRY OF ORIGIN
(IF OTHER THAN USA)
A3
A
A2
DIE
A
A3
A2
b
K
D
E
e
D2
E2
L
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
MIN
0.80
0
0.25
0.20
2.50
2.50
0.35
NOM
0.90
0.20 REF
0.65
0.30
4.00 BSC
4.00 BSC
0.65
2.65
2.65
0.40
MAX
1.00
1.00
0.35
-
2.80
2.80
0.45
Page 9 of 10
Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
0.05-4.0 GHz
Dual High Dynamic Range Amplifier
CDQ6004-QS
August 2007 - Rev 11-Aug-07
Handling and Assembly Information
CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human
body and the environment. For safety, observe the following procedures:
Do not ingest.
Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical
processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed.
Observe government laws and company regulations when discarding this product. This product must be
discarded in accordance with methods specified by applicable hazardous waste procedures.
Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support
devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As
used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into
the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions
for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical
component is any component of a life support device or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or system, or to affect its safety or effectiveness.
Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package
compatible with high volume solder installation. Care should be taken not to apply heavy pressure to the top or base
material to avoid package damage. Vacuum tools or other suitable pick and place equipment may be used to pick and
place this part. Care should be taken to ensure that there are no voids or gaps in the solder connection so that good RF,
DC and ground connections are maintained. Voids or gaps can eventually lead not only to RF performance degradation,
but reduced reliability and life of the product due to thermal stress.
Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental
requirements for eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix
RoHS compliant components are form, fit and functional replacements for their non-RoHS equivalents. Lead plating of
our RoHS compliant parts is 100% matte tin (Sn) over copper alloy and is backwards compatible with current standard
SnPb low-temperature reflow processes as well as higher temperature (260°C reflow) “Pb Free” processes.
Ordering Information
Part Number for Ordering
Description
CDQ6004-QS-0G00
CDQ6004-QS-0G0T
Matte Tin plated RoHS compliant QFN4x4 16L surface mount package in bulk quantity
Matte Tin plated RoHS compliant QFN4x4 16L surface mount package in tape and reel
PB-CDQ6004-QS-00A0
PB-CDQ6004-QS-00B0
PB-CDQ6004-QS-00C0
CDQ6004-QS Evaluation Board @ 900 MHz
CDQ6004-QS Evaluation Board @ 1.9 GHz~2.1 GHz
CDQ6004-QS Evaluation Board @ 2.4 GHz
We also offer this product with SnPb (Tin-Lead) or NiPdAu plating. Please contact your regional sales manager for more information
regarding different plating types.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 10 of 10
Characteristic Data and Specifications are subject to change without notice. ©2007 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.