LOW PROFILE HIGH
FREQUENCY RELAY
10.6
.417
RP-RELAYS
• High frequency relay with the low profile of 4 mm .157 inch
• Excellent high frequency characteristics
Isolation: Min. 10dB (at 1.8 GHz)
Insertion loss: Max. 1.0dB (at 1.8 GHz)
V.S.W.R.: Max. 1.3 (at 1.8 GHz)
• High sensitivity in small size
Size: 10.6 × 9 × 4 mm .417 × .354 × .157 inch
Nominal operating power: 140 mW
9
.748
4
.157
mm inch
SPECIFICATIONS
Contact
Characteristics
Arrangement
Contact material
Stationary
Initial contact resistance, max.
(By voltage drop 6 V DC 0.1 A)
Nominal switching capacity
Rating
Isolation
High frequency
characteristics
(Impedance 50Ω)
Expected life
(min. operations)
Operate time*3 (at nominal voltage)
0.1 A 30 V DC
Contact switching power: 1 W
(Max. 1.8 GHz); Contact carrying
power: 3 W (Max. 1.2 GHz)
1 W (Max. 1.8 GHz)
Min. 15 dB (at 1 GHz)
Min. 10 dB (at 1.8 GHz)
Max. 0.5 dB (at 1 GHz)
Max. 1 dB (at 1.8 GHz)
V.S.W.R.
Max. 1.2 (at 1 GHz)
Max. 1.3 (at 1.8 GHz)
Max. 50°Cwith nominal coil
voltage across coil and at
nominal switching capacity
Temperature rise
Functional*4
Shock resistance
Destructive*
Min. 500 m/s2 {50 G}
5
Min. 1,000 m/s2 {100 G}
10 to 55 Hz
at double amplitude of 3 mm
10 to 55 Hz
at double amplitude of 5 mm
Functional*6
Vibration
resistance
Destructive
105 (0.1 A 30 V DC)
Conditions for operation,
transport and storage
105 (1 W at 1.8 GHz;
V.S.W.R.: max. 1.3)
Voltage type
Nominal operating power
1.5 to 12 V DC
140 mW
24 V DC
270 mW
Ambient temp.
(Not freezing and condensing
Humidity
at low temperature)
Coil (at 25°C, 68°F)
750 Vrms for 1 min.
1,500 Vrms for 1 min.
Max. 3 ms
(Approx. 1.5 ms)
Max. 2 ms
(Approx. 1 ms)
Release time(without diode)*3
(at nominal voltage)
5×106
TYPICAL APPLICATIONS
Min. 1,000 MΩ at 500 V DC
Initial breakdown Between open contacts
voltage*2
Between contacts and coil
50 mΩ
Insertion loss
Electrical
(at 20 cpm)
Initial insulation resistance*1
Gold-clad silver
Mechanical
(at 180 cpm)
20 cpm
Max. operating speed (at rated load)
1 Form C
Silver alloy
Movable
–40°C to 70°C
–40°F to 158°F
5 to 85% R.H.
Approx. 1 g .04 oz
Unit weight
Remarks
* Specifications will vary with foreign standards certification ratings.
*1 Measurement at same location as “Initial breakdown voltage” section
*2 Detection current: 10mA
*3 Excluding contact bounce time
*4 Half-wave pulse of sine wave: 11ms, detection time: 10µs
*5 Half-wave pulse of sine wave: 6ms
*6 Detection time: 10µs
ORDERING INFORMATION
• Antenna switching of mobile phone
• Switching signal of measuring equipment
Ex. RP
1
H
3V
Contact arrangement
Terminal shape
Coil voltage (DC)
1:1 Form C
Nil: Standard PC board terminal
H: Self-clinching terminal
1.5, 3, 4.5, 5, 6, 9, 12, 24 V
Note: Standard packing; Carton: 50 pcs. Case 1,000 pcs.
93
RP
TYPES ANE COIL DATA (at 20°C 68°F)
Self-clinching
terminal
Nominal
voltage,
V DC
Pick-up
voltage, max.
V DC
Drop-out
voltage, min.
V DC
Coil
resistance,
Ω (±10%)
Nominal
operating
current,
mA (±10%)
Nominal
operating
power,
mW
Maximum.
allowable
voltage,
V DC
RP1-H-1.5V
RP1-H-3V
RP1-H-4.5V
RP1-H-5V
RP1-H-6V
RP1-H-9V
RP1-H-12V
RP1-H-24V
1.5
3
4.5
5
6
9
12
24
1.125
2.25
3.375
3.75
4.5
6.75
9
18
0.15
0.3
0.45
0.5
0.6
0.9
1.2
2.4
16
64.3
145
178
257
579
1,028
2,133
93.8
46.7
31.1
28
23.3
15.6
11.7
11.3
140
140
140
140
140
140
140
270
2.25
4.5
6.75
7.5
9
13.5
18
28.8
Part No.
Standard PC
board terminal
RP1-1.5V
RP1-3V
RP1-4.5V
RP1-5V
RP1-6V
RP1-9V
RP1-12V
RP1-24V
DIMENSIONS
mm inch
Standard PC board terminal
3.75
.148
4
.157
3.5
.138
10.6
.417
PC board pattern (Copper-side view)
5.08
.200
9
.354
7.62
.300
0.5
.020
2.54
.100
(0.25)
(.010)
2.54
.100
7.62
.300
0.25
.010
6-1 dia.
6-.039 dia.
Tolerance: ±0.1 ±.004
Self-clinching terminal
3.75
.148
4
.157
3.5
.138
2.54
.100
10.6
.417
Schematic (Bottom view)
9
.354
1 2 3
+
(0.25)
(.010)
2.54
.100
0.5
.020
2.54
.100
7.62
.300
0.25
.010
–
6 5 4
Direction indication
General tolerance: ±0.3 ±.012
Deenergized condition
REFERENCE DATA
Sample: RP1-6V
Measuring method: Impedance 50Ω
Measuring tool:
6–1.00 dia
.039 dia
26–0.80 dia
.031 dia
18.92
.745
0.60
.024
1. High frequency characteristics
• Isolation
mm inch
6–2.30 dia
.090 dia
PC board
• Double-sided through hole
• Material: Glass-epoxy resin
• t= 1.0mm .039 inch
• Copper plated thickness: 35 µm
1.94
.076
18.00 7.62
.709 .300
100
90
80
Isolation, dB
6–1.60 dia
.063 dia
70
60
50
40
4.22 9.82
.166 .387
30
20
5.08
.200
10
0
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
Soldering
SMA connector
• Return loss
4
Return loss, dB
Insertion loss, dB
5
3
2
N.O. (Terminal Nos. 5-6)
N.C. (Terminal Nos. 4-5)
1
100
3.0
90
2.8
80
2.6
70
2.4
60
50
40
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0
2.2
2.0
1.8
1.6
1.4
20
Frequency, GHz
94
N.O. (Terminal Nos. 5-6)
30
10
0
• V.S.W.R
V.S.W.R.
• Insertion loss
Frequency, GHz
N.C. (Terminal Nos. 4-5)
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
Frequency, GHz
1.2
1.0
N.C.
N.O.
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
Frequency, GHz
RP
2. Coil temperature rise
3. Operate/release time
Sample: RP1-6V; No. of samples: n = 5
Carrying current: 0.1 A
Ambient temperature: 25°C 77°F
Sample: RP1-9V; No. of samples: n = 50
• With diode
• Without diode
12
12
100
60
50
8
6
8
6
40
4
4
30
20
Max.
Max.
Min.
Min.
2
10
0
0
80
100
120
70 80
150
100
2
120
0
150
Coil applied voltage, %V
Coil applied voltage, %V
4. Mechanical life
5. Electrical life (0.1 A 30 V DC)
Sample: RP1-5V; No. of samples: n = 8
Sample: RP1-6V; No. of samples: n = 6
• Change of pick-up, drop-out voltage
• Change of pick-up/drop-out voltage
12
8
6
4
Pick-up voltage
Max.
Min.
Max.
Min.
2
50
10
8
6
Pick-up voltage
4
Max.
2
Min.
Max.
Min.
0
10
20
No. of operations, ×104
7. Contact resistance distribution (initial)
Sample: RP1-6V; No. of samples: n = 5
Sample: RP1-6V; No. of samples: n = 25
60
40
Max.
Min.
0
30
10
20
No. of operations, ×104
40
Drop-out
voltage
20
Pick-up
voltage
20 40 60 80
Ambient
–20 temperature, °C
40
30
20
10
–40
0
22 24 26 28 30 32 34 36 38 40
Contact resistance, mΩ
OFF
5
Pick-up voltage
0
OFF
–5
5
OFF
OFF
Pick-up voltage
0
–5
Rate of change, %
8.-(3) Influence of adjacent mounting
Sample: RP1-12V; No. of samples: n = 6
Rate of change, %
8.-(2) Influence of adjacent mounting
Sample: RP1-12V; No. of samples: n = 6
Rate of change, %
8.-(1) Influence of adjacent mounting
Sample: RP1-12V; No. of samples: n = 6
5
Pick-up voltage
0
–5
OFF
Drop-out voltage
0
ON
–5
5
ON
ON
Drop-out voltage
0
ON
–5
Rate of change, %
ON
5
OFF
Rate of change, %
Rate of change, %
OFF
5
Drop-out voltage
0
–5
ON
0
30
50
Quantity
Rate of change, %
80
20
6. Ambient temperature characteristics
0
100
Drop-out voltage
Drop-out voltage
100
500 1,000
No. of operations, ×104
–40 –20
100
120
150
Coil applied voltage, %V
120
Contact resistance, mΩ
10
Max.
Min.
Max.
Min.
70 80
• Change of contact resistance
12
Pick-up/drop-out voltage, V
Pick-up/drop-out voltage, V
10
Time, ms
70
Time, ms
Temperature rise, °C
10
80
Operate time
Release time
Operate time
Release time
90
5
10
.197
.394
Inter-relay distance, (mm, inch)
ON
0
5
10
.197
.394
Inter-relay distance, (mm, inch)
0
5
10
.197
.394
Inter-relay distance, (mm, inch)
95
RP
9. High frequency switching test (1.2 GHz, 1 W)
Sample: RP1-6V; No. of samples: n = 6
Ambient temperature: 20°C 68°F
RP relay
Transmission
T1
Dummy load (50Ω)
WD-2351
Transmission: RF Tranceiver
IC-1201 (ICOH)
T2
T1
ON
OFF
T2
0.2s
1.5s
12
120
10
100
8
6
Pick-up voltage
Max.
Min.
4
Drop-out voltage
2
0.2s
1.5s
• Change of contact resistance
Contact resistance, mΩ
Pick-up/drop-out voltage, V
• Change of pick-up/drop-out voltage
80
60
40
Max.
Min.
20
Max.
Min.
0
5
10
0
15
No. of operations, ×104
5
10
No. of operations, ×104
15
NOTES
Orientation (indicates PIN No. 1) stripe
Stopper (green)
2. Automatic mounting
To maintain the internal function of the
relay, the chucking pressure should
not exceed the values below.
Chucking pressure* in the direction A:
4.9 N {500 gf} or less
Chucking pressure* in the direction B:
9.8 N {1 kgf} or less
Chucking pressure* in the direction C:
9.8 N {1 kgf} or less
Please chuck the
portion.
Avoid chucking the center of the relay. In
addition, excessive chucking pressure to
the pinpoint of the relay should be avoided.
,
,
1. Packing direction
Relays are packed in a tube with the orientation stripe (PIN NO. 1) toward the
green stopper.
A
(4)
(5)
(6)
C
3. Soldering
Preheat according to the following conditions.
Temperature
Time
100°C 212°F or less
Within 1 minute
Soldering should be done at 250°C
482°F within 5 s.
mm inch
B
• Direction A • Direction B • Direction C
6 5 4
3
.118
6
.236
3
2
1
2
3
1
*Value of chucking pressure is shown by the value of weight
pressed on the portion (4 mm .157 inch dia.).
For Cautions for Use, see Relay Technical Information (Page 48 to 76).
96
9/1/2000
All Rights Reserved, © Copyright Matsushita Electric Works, Ltd.
Go To Online Catalog