HMC-C008 v05.1007 AMPLIFIERS 1 15 WATT POWER AMPLIFIER MODULE, 1.8 - 2.2 GHz D E U N I T N O T C C S U I D D O PR Features P1dB Output Power: 15 Watts from 1.8 to 2.2 GHz Gain: 40 dB min Noise Figure: 6 dB Thermally Compensated and Protected Reverse Polarity Protected TTL DC Power Enable Unconditionally Stable Heat Sink/Fan Accessories Available ew N r fo d e end m Typical Applications com e R Test applications for: Not • Cellular/PCS/3G Infrastructure ns g i s De • Automated Test Equipment (ATE) • Laboratory Use Functional Diagram General Description The HMC-C008 is a 15 Watt Power Amplifier Module suitable for Cellular/3G repeaters, laboratory use and ATE applications. The unit includes DC power sequencing, enable and conditioning, as well as an output circulator for load mismatch protection. Thermal protection/fault circuitry automatically turns off DC power at base temperatures exceeding +75 °C and restores power at < +55 °C. Electrical Specifi cations, TA = +25° C, VIN = +12V Parameter Min. Frequency Range Gain Max. 40 Units GHz 42 dB Noise Figure 6 Input Return Loss 12 dB 12 dB Saturated Output Power (Psat) 43 dBm Output Third Order Intercept (IP3) (Two-tone Input Power = -28 dBm each tone) 52 dBm Channel Output Power for -50 dBc ACPR (CDMA 2000, 1960 MHz) 36 dBm Channel Output Power for -50 dBc ACPR (W-CDMA, 2110 MHz) 33 dBm Second Harmonic at Output P1dB -55 dBc Third Harmonic at Output P1dB -55 dBc Spurious at Output P1dB -65 Supply Current 6.5 Output Return Loss Output Power for 1 dB Compression (P1dB) 1-1 Typ. 1.8 - 2.2 8 15 dB W dBc 7.0 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com A HMC-C008 v05.1007 15 WATT POWER AMPLIFIER MODULE, 1.8 - 2.2 GHz D E U N I T N O T C C S U I D D O PR Gain vs. Temperature 44 GAIN (dB) 42 41 40 39 RETURN LOSS (dB) -5 43 +25C +50C 0C 38 37 -10 -15 -20 -25 ew N r fo d e end m com e R Not ns g i s De -30 INPUT OUTPUT -35 36 35 1.7 1.8 1.9 2 2.1 2.2 -40 1.7 2.3 1.8 1.9 P1dB vs. Temperature 44 44 42 42 40 40 38 Psat (dBm) 46 +25C +50C 0C 36 38 34 32 32 1.9 2 2.1 2.2 30 1.7 2.3 1.8 1.9 FREQUENCY (GHz) -25 ACPR (dBc) WCDMA Frequency : 2.11 GHz Integration BW: 3.84 MHz 64 DPCH -40 -45 -50 -55 -60 -65 -70 22 24 26 28 30 32 34 2 2.1 2.2 2.3 ACPR @ 1960 MHz, CDMA-2000 -20 -35 2.3 FREQUENCY (GHz) ACPR @ 2110 MHz, W-CDMA -30 2.2 +25C +50C 0C 36 34 1.8 2.1 Psat vs. Temperature 46 30 1.7 2 FREQUENCY (GHz) FREQUENCY (GHz) P1dB (dBm) AMPLIFIERS 0 45 ACPR (dBc) 1 Input & Output Return Loss 36 CHANNEL OUTPUT POWER (dBm) 38 40 -20 -25 -30 -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 -85 CDMA2000 Rev. 8 Frequency : 1.96 GHz Integration BW: 1.228 MHz Forward Link, SRI, 9 CHANNELS 22 24 26 28 30 32 34 36 38 40 CHANNEL OUTPUT POWER (dBm) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 1-2 HMC-C008 v05.1007 15 WATT POWER AMPLIFIER MODULE, 1.8 - 2.2 GHz Output IP3 vs. Temperature 60 Reverse Isolation vs. Temperature 0 58 -10 ISOLATION (dB) 56 IP3 (dB) AMPLIFIERS 1 D E U N I T N O T C C S U I D D O PR 54 52 50 46 1.7 1.8 1.9 -30 -40 ew N r fo d e end m com e R Not 2 2.1 -60 2.2 2.3 -70 1.7 1.8 FREQUENCY (GHz) 9 8 NOISE FIGURE (dB) 2 2.1 2.2 2.3 Absolute Maximum Ratings 10 7 6 5 4 +25C +50C 0C 2 1.9 FREQUENCY (GHz) Noise Figure vs. Temperature 3 ns g i s De -50 +25C +50C 0C 48 +25C +50C 0C -20 Supply Voltage (VIN) +13 Vdc RF Input Power (RFIN) +10 dBm Storage Temperature -40 to +70 °C Operating Temperature 0 to +50 °C RF Output Isolator Max Dissipation 20 W Thermal Fault Indicator Max Pdiss (derate 1.8 mW/°C above 50 °C) 180 mW Enable Vmax 6V 1 0 1.7 1.8 1.9 2 2.1 2.2 ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 2.3 FREQUENCY (GHz) Thermal Fault Indicator Characteristics Parameter Min. IOUT (VOUT > 2V) Typ. 1 Parameter Max. Units 7.5 Ohms VIH VIL MOhm IIL @ VIN = 0V 350 RON (I OUT = 50 mA) ROFF (VOUT = 30 V) Enable Input Characteristics mA IIH @ 5V Min. Typ. Max. Units 1.6 V 3.5 V -0.5 mA < ± 50 μA Recommended Biasing Procedure TURN-ON 1. Connect RF input and output 2. Apply Supply Voltage VIN (+12 Vdc) 3. Set Enable low 4. Apply RF input signal TURN-OFF 1. Remove RF input signal 2. Remove Supply Voltage VIN 1-3 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC-C008 v05.1007 15 WATT POWER AMPLIFIER MODULE, 1.8 - 2.2 GHz Pin Descriptions Pin Number 1 2 3 Function Description RFIN & RF Ground RF input connector, SMA female. This pin is AC coupled and matched to 50 Ohms. VIN GND ew N r fo d e end m com e R Not Power supply voltage for the amplifier. Interface Schematic ns g i s De 1 AMPLIFIERS D E U N I T N O T C C S U I D D O PR Power supply ground. 4 RFOUT & RF Ground RF output connector, SMA female. This pin is isolator protected and matched to 50 Ohms. 5 GND Ground for thermal fault indicator and enable circuit. 6 Thermal Fault Indicator Open drain output. High impedance for base plate temperatures less than 55 °C. Low impedance for base plate temperatures exceeding 75 °C. TTL compatible supply voltage (VIN) shutdown. If enable feature is not required, short this pin to DC ground. 7 Enable TTL “High” Disable TTL “Low” Enable For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 1-4 HMC-C008 v05.1007 15 WATT POWER AMPLIFIER MODULE, 1.8 - 2.2 GHz AMPLIFIERS 1 D E U N I T N O T C C S U I D D O PR Outline Drawing ew N r fo d e end m com e R Not ns g i s De Package Information Package Type Package C-7 Weight [1] Spacer Weight 740 gms [2] N/A [1] Includes the connectors [2] ±10% Tolerance NOTES: 1. MATERIAL: ALUMINUM 6061-T6 2. FINISH a. COVER & END PLATES, CHEMICAL FILM PER MIL-C-5541, CLASS 3 b. BASE, TIN 3. RF CONNECTORS, SMA STYLE 4. DIMENSIONS ARE INCHES (MM) 5. TOLERANCES .X±.1 (2.54mm) .XX±.02 (0.50mm) 6. BASE MUST BE GROUNDED AND MOUNTED TO HEAT SINK CAPABLE OF DISSIPATING 100W (50 °C) 1-5 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC-C008 v05.1007 15 WATT POWER AMPLIFIER MODULE, 1.8 - 2.2 GHz HMC-C008 Heatsink/Fan Outline Drawing ew N r fo d e end m com e R Not ns g i s De 1 AMPLIFIERS D E U N I T N O T C C S U I D D O PR NOTES: 1. MATERIAL: ALUMINUM 6061-T6 2. FINISH: COVER & END PLATES, CHEMICAL FILM PER MIL-C-5541, CLASS 3 3. RF CONNECTORS, SMA STYLE 4. DIMENSIONS ARE INCHES (MM) 5. TOLERANCES .X±.1 (2.54mm) .XX±.02 (0.50mm) HMC-C008 Ordering Information Part Number Description HMC-C008 15 Watt Power Amplifier Module, 1.8 - 2.2 GHz HMC-C008HV115 15 Watt Power Amplifier Module with heat sink, 115 Vac fan and power cord. HMC-C008HV230 15 Watt Power Amplifier Module with heat sink, 230 Vac fan and power cord. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 1-6