RGL1A-RGL1M Surface Mount Rectifiers VOLTAGE RANGE: 50 --- 1000 V CURRENT: 1.0 A DO - 213AA Features ◇ Plastic package has underwriters laboratories SOLDERABLE ENDS flammability classification 94V-0 Glass passivated chip junction ◇ For surface mount applications ◇ High temperature metallurgically bonded construction ◇ Cavity-free glass passivated junction ◇ High temperature soldering guaranteed:450 ℃/5 seconds D2 D1 ◇ 1.6± 0.1 0 D2=D1 ＋ －0.20 0.5± 0.1 0.5± 0.1 at terminals.Complete device sub-mersible temperature 3.5± 0.2 of 265℃ for 10 seconds in solder bath Mechanical Data Dimensions in millimeters ◇ Case: JEDEC DO-213AA,molded plastic ◇ Polarity: Color band denotes cathode ◇ Weight: 0.0014 ounces, 0.036 grams ◇ Mounting position: Any MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified. Single phase,half wave,60 Hz,resistive or inductive load. For capacitive load,derate current by 20%. RGL 1A Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current TT=75℃ VRRM VRMS VDC 50 35 50 RGL RGL RGL RGL RGL RGL UNITS 1B 1D 1G 1J 1K 1M 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 V V V I(AV) 1.0 A IFSM 25 A VF 1.3 V IR 5.0 50 µA Peak forward surge current 8.3ms single half-sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage @1.0A Maximum reverse current @T A=25℃ at rated DC blocking voltage @T A=125℃ Maximum reverse recovery time (Note 1) Typical thermal resistance (Note 3) Operating junction temperature range Storage temperature range trr 150 250 ns RθJA 150 ℃/W Tj - 55 ---- +175 ℃ TSTG - 55 ---- +175 ℃ NOTE: 1. Measured with IF=0.5A,IR=1.0A,Irr=0.25A 2. Measured at 1.0MHz and applied reverse voltage of 4.0V DC. 3. Thermal resistance from junction to ambient, 0.24×0.24"(6.0×6.0mm) copper pads to each terminal. http://www.luguang.cn 500 mail:[email protected] RGL1A-RGL1M Surface Mount Rectifiers Ratings AND Charactieristic Curves FIG.2 -- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 1 .5 R E S IS T IV E O R IN D U C T IV E LOAD PEAK FORWARD SURGE CURRENT,AMPERES AVERAGE FORWARD RECTIFIED CURRENT,AMPERES FIG.1 -- FORWARD CURRENT DERATING CURVE 1 .0 0 .8 0 .6 0 .4 0 .2 0 .2 X 0 .2 "(5 .0 X 5 .0 m m ) COPPER PAD AREAS 0 50 25 75 100 125 150 175 25 TL=110℃ 8.3ms SINGLE HALF SINE-WAVE (JEDEC METHOD) 12.5 0 1 TERMINAL TEMPERATURE ℃ NUMBER OF CYCLES AT 60HZ FIG.3 -- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4 -- TYPICAL REVERSE CHARACTERISTICS 100 1 INSTANTANEOUS REVERSE LEAKAGE CURRENT(mA) 10 INSTANTANEOUS FORWARD CURRENT,AMPERES 100 10 T J =25 Pulse Width=300us 0.1 0.01 0.001 0.6 0.8 1.0 1.2 1.4 1.6 TA=125℃ 10 TA=100℃ 1 TA=25℃ 0.1 0.01 0 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE. ( ％) INSTANTANEOUS FORWARD VOLTAGE(V) FIG.5 -- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM trr 50 N.1. 10 N.1. +0.5A D.U.T. ( - ) 0 PULSE GENERATOR (NOTE2) (+) 50VDC (APPROX) (-) 1 N.1. OSCILLOSCOPE (NOTE 1) -0.25A ( + ) -1.0A 1cm NOTES:1.RISETIME=7ns MAX. INPUT IMPEDANCE=1M .22pF 2.RISETIME=10ns MAX. SOURCEIMPEDANCE=5O http://www.luguang.cn 100 SET TIME BASE FOR 75/150 ns /cm mail:[email protected]