LUGUANG ZTTCE11.06MG

ZTTCE11.06MG
SMD Ceramic Resonators
1. SCOPE
This specification shall cover the characteristics of the ceramic
resonator with the type ZTTCE11.06MG.
2. PART NO.:
PART NUMBER
CUSTOMER PART NO SPECIFICATION NO
ZTTCE11.06MG
3. OUTLINE DRAWING AND DIMENSIONS:
Appearance: No visible damage and dirt.
Dimensions:
[ Unit: mm ]
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
ZTTCE11.06MG
SMD Ceramic Resonators
4. ELECTRICAL SPECIFICATIONS:
No
Requirements
Item
4.1 Oscillation Frequency Fosc (MHz)
11.06
Frequency Accuracy (%)
±0.5
4.2 Resonant Impedance Ro (Ω)max
30
4.3
Temperature Coefficient of
±0.3 (Oscillation Frequency
Oscillation Frequency (%) max
drift -20℃ to +80℃)
4.4
Withstanding Voltage
50 VDC, 1 min
4.5
Rating Voltage UR (V)
(1) D.C. Voltage
6 VDC.
(2) A.C. Voltage
15 Vp-p.
4.6 Insulation Resistance Ri,(MΩ)min
100 ( 100V, 1min)
4.7
4.8
4.9
Operating Temperature (℃)
Storage Temperature
(℃)
Aging Rate (%) max
-40~+85
-55~+85
±0.3 (For 10 years)
5. MEASUREMENT:
Measurement Conditions: Parts shall be measured under a condition
( Temp. : 20±15 ℃ ,Humidity : 65±20% R.H.) unless the standard
condition(Temp. : 25±3 ℃ ,Humidity : 65±5% R.H.) is regulated to
measure.
Test Circuit:
IC:1/6TC4069UBP×2
X:CERAMIC RESONATOR
C1 C2:30pF
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
ZTTCE11.06MG
SMD Ceramic Resonators
6. PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS
No
Item
6.1
Humidity
6.2
Vibration
6.3
Mechanical
Shock
6.4
Soldering
Test
6.5
Solder
Ability
6.6
High
Temperature
Exposure
6.7
Low
Temperature
Exposure
Condition of Test
Keep the resonator at 40±2℃ and 90-95% RH
for 96±4 hours. Then Release the resonator into
the room Condition for 1 hour prior to the
Measurement.
Subject the resonator to vibration for 2 hours
each in x、y and z axis With the amplitude of
1.5mm, the frequency shall be varied uniformly
between the limits of 10 Hz—55Hz.
Drop the resonator randomly onto a wooden
floor from the height of 100cm 3 times.
Performance
Requirements
It shall fulfill
the
specifications
in Table 1.
It shall fulfill
the
specifications
in Table 1.
It shall fulfill
the
specifications
in Table 1.
It shall fulfill
the
specifications
in Table 1.
Passed through the re-flow oven under the
following condition and left at room
temperature for 1 hour before measurement.
Temperature at the surface of the
Time
substrate
Preheat 150±5℃
60±10
sec
Peak
240±5℃
10±3 sec
Dipped in 230±5℃ solder bath for 3±0.5 sec The terminals
seconds with rosin flux (25wt% ethanol shall be at
solution.)
least
95%
covered
by
solder.
Subject the resonator to 80±5℃ for 96 hours, It shall fulfill
then release the resonator into the room the
conditions for 1 hour prior to the measurement. specifications
in Table 1.
Subject the resonator to -20±5℃ for 96 hours, It shall fulfill
then release the resonator into the room the
conditions for 1 hour prior to the measurement. specifications
in Table 1.
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
ZTTCE11.06MG
SMD Ceramic Resonators
6. PHYSICAL AND ENVIRONMENAL CHARACTERISICS
(Continued from the preceding page)
No
Item
Condition of Test
6.8
Temperature
Cycling
6.9
Board
Bending
Performance
Requirements
Subject the resonator to -40℃ for 30 It shall fulfill the
min. followed by a high temperature of specifications
in
85℃ for 30 min.
Table 1.
Cycling shall be repeated 5 times with a
transfer time of 15 sec. At the room
temperature for 1 hour prior to the
measurement.
Mount
a
glass-epoxy
board Mechanical damage
(Width=40mm,thickness=1.6mm),then bend it such as breaks shall
to 1mm displacement and keep it for 5 seconds. not occur.
(See the following figure)
PRESS
PRESS HEAD
SUPPORT BAR
TABLE 1
Item
Oscillation Frequency Change
△Fosc/Fosc (%) max
Resonant Impedance Change
△Ro(Ω)max
Specification
±0.3
±10
Note: The limits in the above table are referenced to the initial measurements.
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
ZTTCE11.06MG
SMD Ceramic Resonators
7. REVIEW OF SPECIFICATIONS
When something gets doubtful with this specifications, we shall
jointly work to get an agreement.
8. RECOMMENDED LAND PATTERN AND REFLOW SOLDERING
STANDARD CONDITIONS
8.1Recommended land pattern
DIMENSIONS (mm)
T1
T2
T3
W1
0.4±0.2
0.4±0.1
1.2±0.1
1.3±0.15
8.2Recommended reflow soldering standard conditions
Temperature(℃)
within 10 sec
℃
Pre-heating
within
80-120sec.
within
20-40sec
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
ZTTCE11.06MG
SMD Ceramic Resonators
9. PACKAGE
To protect the products in storage and transportation , it is
necessary to pack them(outer and inner package).On paper pack, the
following requirements are requested.
Dimensions and Mark
At the end of package, the warning (moisture proof, upward put)
should be stick to it.
Dimensions and Mark (see below)
NO.
Name
Quantity
1
Package
1
2
Certificate of approval
1
3
Label
1
4
Tying
2
5
Adhesive tape
1.2m
6
Belt
2.9m
7
Inner Box
10
Notes
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
ZTTCE11.06MG
SMD Ceramic Resonators
Section of package
Package is made of corrugated paper with thickness of
0.8cm.Package has 10 inner boxes, each box has 1 reel(each reel for
plastic bag)
Quantity of package
Per plastic reel
4000 pieces of
piezoelectric ceramic part
Per inner box
1 reel
Per package
10 inner boxes(40000 pieces of
piezoelectric
ceramic part )
Inner Packing Dimensions
1.UNIT: mm
1
Label
2
QC Label
3
Inner Box
Pars shall be packaged in box with hold down tape upside. Part
No., quantity and lot No.
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
ZTTCE11.06MG
SMD Ceramic Resonators
8.5Reel
Dimensions
φA
φB
Unit:mm
W
T
330±3 80min 16.4min 22.4max
Pieces per reel Carrier tape size
4000typ.
16
8.6Taping Dimensions
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.
ZTTCE11.06MG
SMD Ceramic Resonators
8.7Packing Method Sketch Map
Blank Pocket
10 Pitches
Loaded Pocket
Leader
200mm Max
Blank Pocket
10 Pitches
8.8Test Condition Of Peeling Strength
T op T ape
g
P e e lin
S tre n
g th 2 0 - 7 0
g
10° Max
C a r r ie r T a p e
SHENZHEN LUGUANG ELECTRONIC TECHNOLOGY CO.,LTD.