★INPUT VOLTAGE:1200VDC PV SERIES NEW POWER SOURCES 200-1200VDC OVERWIDE AND OVERHIGH INPUT VOLTAGE ISOLATION CONVERTER PV series are 200-1200VDC input voltage regulated DC-DC converter. It features ultra-high input voltage, high efficiency, high reliability, it can be widely used in PV power generation and high voltage inverter occasion, provide a stable operating voltage to the load equipment. Its own multiple protection features can enhance the safety performance of the power and load when module work under abnormal conditions. RoHS PRODUCT FEATURES PART NUMBER SYSTEM ● ● ● ● ● ● ● ● ● ● ● PV05-27B05 6:1 ultra-wide input voltage range: 200 ~ 1200VDC Industrial operating temperature: -40℃ ~ 70℃ 4000VDC high isolation voltage high efficiency, Low ripple& noise Under input voltage protection (automatic recovery) Over output voltage protection(automatic recovery) Short circuit protection(automatic recovery) Input against reverse protection MTBF>300 K hours High reliability, long life, three years warranty Offer custom products SELECTION GUIDE Model Package Output Input Voltage Range (VDC) PV05-27B05 PV10-27B05 PV10-27B09 74.0x52.0x28.0mm Voltage (VDC) 5 Current (mA) 1000 5 2000 9 1111 24 420 200～1200 PV10-27B24 Isolation Voltage (VDC) Efficiency (%,Typ) Ripple& noise (Max.) 73 4000 75 78 100mV 83 INTPUT SPECIFICATIONS Input Voltage Range Input Current 200～1200VDC 1200VDC 200VDC 600VDC PV05 models 34mA(Typ.) 12mA (Typ.) 9mA (Typ.) PV10 models 66mA (Typ.) 22mA (Typ.) 14mA (Typ.) 200VDC 600VDC 1200VDC 8A (Typ.) 12A (Typ.) 25A (Typ.) Inrush Current 1A Slow blow External input fuse OUTPUT SPECIFICATIONS Output voltage accuracy ±1% (Typ.) ±2% (Typ.) Line regulation ±0.5% (Typ.) ±1% (Typ.) Load regulation ±0.5% (Typ.) ±1% (Typ.) 50mV (Typ.) 100mV (Typ.) Ripple& noise(p-p) 20MHz Bandwidth Short circuit protection Continuous, and auto resume Under input voltage protection Undervoltage protection range: 175～185V Undervoltage release range:185～195V Over output voltage protection Max. Capacitive Load(Full load) Output Power PV05-27B05 (Feedback-clamp) Voltage limited < 6.5V PV10-27B05 (Feedback-clamp) Voltage limited < 6.5V PV10-27B09 (Feedback-clamp) Voltage limited < 11.5V PV10-27B24 (Feedback-clamp) Voltage limited < 27V PV05-27B05 10000μF PV10-27B05 6000μF PV10-27B09 4000μF PV10-27B24 1500μF PV05-27B05 5W PV10-27B24 10W The copyright and authority for the interpretation of the products are reserved by MORNSUN. Specifications subject to change without notice. PV Series A/1-2012 Page 1 of 3 COMMON SPECIFICATIONS Temperature ranges Operating -40℃～+70℃ Storage -40℃～+105℃ Case temperature +90℃ Max. Temperature Drift ±0.02 %/°C（Max.） Humidity 20～95% Delay time 1s (Max.) Cooling Free air convection Hot-plugging No support Isolation Voltage 4000VDC/1Min Test at 500VDC Isolation Resistance EMI EMC* EMS > 100 MΩ CE* CISPR22/EN55022 CLASS A RE* CISPR22/EN55022 CLASS A ESD IEC/EN61000-4-2 Contact ±6KV / Air ±8KV perf. Criteria B RS IEC/EN61000-4-3 10V/m perf. Criteria A EFT* IEC/EN61000-4-4 ±4KV perf. Criteria B Surge* IEC/EN61000-4-5 ±2KV/±4KV perf. Criteria B CS IEC/EN61000-4-6 10 Vr.m.s perf. Criteria A PFM IEC/EN61000-4-8 10A/m perf. Criteria A Voltage dips、short and interruptions immunity IEC/EN61000-4-11 0%-70% perf. Criteria B Case Material Aluminium Install PCB MTBF >300,000h @25°C Weight 190 g Note: 1. 2. 3. 4. * External circuit is required to models, refer to EMC typical application. Test ripple and noise by “parallel cable” method. Test efficiency at normal temperature and input voltage is 200VDC. Unless otherwise specified, all specifications above are measured at rated input voltage and rated output load, TA=25°C, humidity < 75%; All specifications stated in this datasheet are subject to the above listed models only. For specifications of non-standard models, please contact our technical support team. PARALLEL LINES MEASURE Co p p e r sh e et F USE + V in +Vo C1 - Vi n C2 Lo a d Co nn e ct Os cillog ra ph Pro be -Vo 12.7m m 25.4mm 2 5. 4 m m Note: C1: 1μF (ceramic capacitor) INPUT VOLTAGE VS LOAD C2: 10μF (electrolytic capacitor) TEMPERATURE VS LOAD PV05-27B05、PV10-27B24： PV10-27B05、PV10-27B09： Load(% ) Load( % ) Load(%) Input：800 V-12 00 V 100 Input：8 00 V-1 20 0 V 100 100 Input：20 0 V-8 00 V 80 80 60 Input：2 00 V- 80 0 V 80 50 50 40 20 200 400 600 1000 1200 -40 Input Voltage(VDC) -20 0 60 -40 70 75 80 -20 Temperature( ℃ ) 60 0 70 75 Temperature( ℃ ) TYPICAL EFFICIENCY CURVE Efficiency VS Output Load curve(Vin=600VDC) 90 80 80 70 70 60 PV05-27B05 PV10-27B05 PV10-27B09 PV10-27B24 50 40 30 Efficiency(%) Efficiency(%) Efficiency VS Input Voltage Curve 90 60 40 30 20 20 10 10 0 PV05-27B05 PV10-27B05 PV10-27B09 PV10-27B24 50 0 200 400 600 800 1000 1200 10 20 Input Voltage(V) The copyright and authority for the interpretation of the products are reserved by MORNSUN. 30 40 50 60 70 80 90 100 Output Current Percent(%) Specifications subject to change without notice. PV Series A/1-2012 Page 2 of 3 EMC TYPICAL APPLICATIONS EMI Recommended Circuit： EMS Recommended Circuit： + INP UT + O UT P UT + + + + C2 R2 C3 R3 C4 R4 C5 R5 + V in NTC + Vin + Vo LOAD C1 +C2 TVS M OV - V in - INP UT F USE + Vo - Vo - Vin RL - Vo - O UT P UT Recommended parameters: Vout TVS C2 Recommended parameters: ① C2、C3、C4、C5:47μF/450V ② R2、R3、R4、R5:1MΩ/2W 5V SMCJ7.0A 224K/50V 24V SMCJ33A 224K/50V Note: Output filtering capacitor C1 is electrolytic capacitors, It is recommended to use high frequency and low impedance electrolytic capacitors. For capacitance and current of capacitor please refer to manufacture’s datasheet. Voltage derating of capacitor should be 80%. TVS is a recommended component to protect post-circuits (if converter fails). External input NTC is recommended to use 5D-9. MOV: Varistor, model: 162KD20，it is used to protect the device under surge. Access as needed. 28.00 [1.102] OUTLINE DIMENSIONS & RECOMMENDED FOOTPRINT (Main View) 6.00 10.16 [0.400] [0.236] 3 5 Ф1.20[0.047] 2 1 2 30.48 [1.200] (Bottom View) N ote :gr id 2.5 4*2 .54 m m . 5 4 3 6 Ф1.70[0.067] 17.78 [0.700] 6 22.86 [0.900] 1 52.00[2.047] 4 60.96[2.400] 74.00[2.913] Pin F un ction 1 2 3 ,4 + Vin -Vin NC -Vo +Vo 5 6 N o te: U n it:m m ( in ch ) Pins ectio n to ler a nc es :± 0 .10 m m [± 0 .0 0 4inc h] G e ne r a l toler a nc es :± 0 .50 m m [± 0 .02 0inc h] PACKAGE DIAGRAM Inner packaging box dimensions:L*W*H=365*350*105mm Package quantity: 24 PCS Outer package box dimensions:L*W*H=390*360*245mm Package quantity: 48 PCS MORNSUN Science & Technology Co.,Ltd. Address: No. 5, Kehui St. 1, Kehui development center, Science Ave., Guangzhou Science City, Luogang district, Guangzhou,P.R.China. Tel: 86-20-28203030 Fax:86-20-38601272 Http://www.mornsun-power.com The copyright and authority for the interpretation of the products are reserved by MORNSUN. Specifications subject to change without notice. PV Series A/1-2012 Page 3 of 3