MVAD065 Series www.murata-ps.com PRELIMINARY 65W High Density AC/DC Power Supply ORDERING GUIDE Model Number Natural Convection Cooling Main Output (V1) 60W 12V 24V 48V MVAD065-12 MVAD065-24 MVAD065-48 65W INPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Input Voltage Operating Range Single phase DC 90 120 47 70 70 120/230 264 300 63 85 85 1.4 Vac Vdc Hz Input Frequency Turn-on Input Voltage Turn-off Input Voltage Input Current FEATURES ITE (2nd) and Medical (3rd ed ed. MOOP MOOP, Risk management) safety approved 65W compact high density Input rising at full load Input falling at full load 90Vac input, full load At 264Vac, at 25°C cold start Inrush Current 2" x 4" standard footprint High efficiency up to 90% Remote Sense OUTPUT CHARACTERISTICS Universal AC input Model Number Low profile - 1U package MVAD065-12 MVAD065-24 MVAD065-48 Convection-cooled operation up to 65W Complies with 5000m altitude Main Output Voltage (V1) Load Current Load Capacitance 12V 24V 48V 0 to 5.0A 0 to 2.71A 0 to 1.36A 0 to 1000μF 0 to 560μF 0 to 330μF Main Output Characteristics (all models) Parameter Conditions Input power < 0.3W @ no load Transient Response Settling Time to 1% of Nominal Turn On Delay Output Voltage Rise Setpoint Accuracy Output Holdup Temperature Coefficient Ripple Voltage & Noise1 50% load step, 1A/μsec slew rate The MVAD065 series switching power supplies utilize advanced component and circuit technologies to deliver high efficiency. Designed for Medical, Telecom, and Industrial applications to satisfy 1U height design considerations, the MVAD065 Series measures only 2.0" x 4.0" x 1.3". All models offer universal AC input and compliance to worldwide safety and EMC standards. A Apk Line, Load, Cross Typical Efficiency Regulation @230Vac full load Input power < 74W DESCRIPTION Vac 60 RoHS compliant Complies with ErP/Energy Star requirement (average efficiency > 87%) 50/60 After application of input power Monotonic, 0 to 100% load 120Vac, 40W, 25°C 115Vac, 100% load ± 2% ± 2% ± 2% Min. 88% 89% 90% Max. Units ±5 200 1 50 ± 0.5 % μsec sec msec % msec %/°C % 10 0.02 1 Compensates for up to 0.4V of lead drop with remote sense connected. Remote Sense Protected against short circuit and reverse connection. 1. Ripple and noise are measured with 0.1 uF of ceramic capacitance and 47 uF of electrolytic capacitance on each of the power supply outputs. A short coaxial cable with 50ohm scope termination is used. 2. Unless otherwise specified all readings are taken at 120Vac input and 25 °C ambient temperature. 3. 0.4V lead drop is compensated in remote sense. 3 www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html www.murata-ps.com/en/3d/acdc.html Available now at www.murata-ps.com/en/3d/acdc.html CB Test Certificate and Test Report For full details go to www.murata-ps.com/rohs (pending) (pending) (pending) www.murata-ps.com/support MVAD065.A01.D10 Page 1 of 5 MVAD065 Series PRELIMINARY 65W High Density AC/DC Power Supply ENVIRONMENTAL CHARACTERISTICS Parameter Conditions Min. Full load 50% load Start up Non-condensing Without derating Telcordia SR-332 M1C3 25°C -40 -10 -10 -20 10 -200 1M Storage Temperature Range Operating Temperature Range Operating Humidity Operating Altitude MTBF Shock Operating, IEC60068-2-27, half-sine 5G, 6ms, 3 times per face, 6 faces Complies Non-operating, IEC60068-2-27, half-sine, 30G, 18ms, 3 times per face, 6 faces Complies Typ. Max. 85 50 70 95 5000 Units °C % m Hours Operating, IEC60068-2-6, 1.0G, 10-150Hz, Complies 10 minutes per axis, on all 3 axes Vibration Non-operating, IEC60068-2-6, 2.0G, 10-150Hz, 10 minutes per axis, on all 3 axes Complies Safety (pending) IEC60950-1:2006/A11:2009 UL60950-1 2nd Ed. 2007-03-27, CSA22.2 N0.60950-1 2nd Ed. 2007.03, EN60950-1:2006+A11:2009 IEC60601-1 Ed. 3 MOOP ANSI/AAMI ES60601-1 (2005+C1:09+A2:10), CSA 22.2 No. 60601-1 (2008) 3rd Edition MOOP EN60601-1:2006 3rd ed. MOOP (Evaluated) CE Marking per LVD Warranty Outside Dimensions Weight 2 years 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm) 0.27lbs (123g) typical PROTECTION CHARACTERISTICS Parameter Conditions Min. Overvoltage Protection Overcurrent Protection Latching (60% load) Hiccup mode 110 110 Typ. Max. Units 160 160 %V1 %Amax Max. Units ISOLATION CHARACTERISTICS Parameter Isolation Leakage Current Touch Current Conditions Primary to Chassis Primary to Secondary Secondary to Chassis 264Vac, 60Hz, 25°C 264Vac, 60Hz, 25°C Min. Typ. 1500 (1MOOP) 3000 (2MOOP) 500 Vac 250 100 Vdc μA μA EMISSIONS AND IMMUNITY Characteristic Standard Compliance Input Current Harmonics Voltage Fluctuation and Flicker IEC/EN 61000-3-2 IEC/EN 61000-3-3 EN 55022 FCC Part 15 IEC/EN 61000-4-2 IEC/EN 61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 IEC/EN 61000-4-6 IEC/EN 61000-4-8 IEC/EN 61000-4-11 Class A Complies Class B Class B Level 4, Criterion A Level 2, Criterion A Level 3, Criterion A Level 4, Criterion A Level 2, Criterion A Level 2, Criterion A Level 3, Criterion B Conducted Emissions ESD Immunity Radiated Field Immunity Electrical Fast Transient Immunity Surge Immunity RF Conducted Immunity Magnetic Field Immunity Voltage dips, interruptions www.murata-ps.com/support MVAD065.A01.D10 Page 2 of 5 MVAD065 Series PRELIMINARY 65W High Density AC/DC Power Supply EMI CONSIDERATIONS For optimum EMI performance, the power supply should be mounted to a metal plate grounded to all 4 mounting holes of the power supply. To comply with safety standards, this plate must be properly grounded to protective earth (see mechanical dimension notes). Pre-compliance testing has shown the standalone power supply to comply with EN55022 class A radiated emissions. Radiated emission results vary with system enclosure and cable routing paths. PERFORMANCE DATA MVAD065-24 Eĸciency (%) MVAD065-12 Eĸciency (%) 95 93 91 89 87 85 83 81 79 77 75 95 93 91 89 87 85 83 81 79 77 75 0.00 1.00 2.00 3.00 4.00 5.00 0.00 0.50 1.00 90Vac 115Vac 230Vac 90Vac 264Vac 115Vac 0.20 0.40 0.60 0.80 2.00 2.50 3.00 230Vac 264Vac Inrush waveform MVAD065-48 Eĸciency (%) 95 93 91 89 87 85 83 81 79 77 75 0.00 1.50 Output Current (A) Output Current (A) 1.00 1.20 1.40 Output Current (A) 90Vac 115Vac 230Vac 264Vac MVAD065 -12 Thermal DeraƟng 70 60 Output power [W] Output power [W] 60 50 40 30 ConvecƟon cooling DirecƟon1-5 20 10 0 -10 MVAD065 -24 and MVAD065- 48 Thermal DeraƟng 70 50 40 30 ConvecƟon cooling DirecƟon1-5 20 10 0 10 20 30 40 50 Ambient temperature [°C] 60 70 80 0 -10 0 10 20 30 40 50 Ambient temperature [° C] 60 70 80 www.murata-ps.com/support MVAD065.A01.D10 Page 3 of 5 MVAD065 Series PRELIMINARY 65W High Density AC/DC Power Supply MECHANICAL DIMENSIONS – MVAD065-12 ONLY Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm) INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS PIN Description Input Connector CN1 : Molex 26-62-4030 1 AC Line (V-) 3 AC Neutral (V+) Spade Connector: #250 GND Earth Ground Output Connector CN2 : Molex 26-60-4060 1, 2 V1 3, 4 DC Return 5 -Remote Sense (NC) 6 +Remote Sense Mating Housing Crimp terminal/pins Molex 09-50-8031 with locking ramp Molex 6838 Series Molex 09-50-8061 with locking ramp Molex 6838 Series www.murata-ps.com/support MVAD065.A01.D10 Page 4 of 5 MVAD065 Series PRELIMINARY 65W High Density AC/DC Power Supply MECHANICAL DIMENSIONS – MVAD065-xx 24V and 48V MODELS Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm) INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS PIN Description Input Connector CN1 : Molex 26-62-4030 1 AC Line (V-) 3 AC Neutral (V+) Spade Connector: #250 GND Earth Ground Output Connector CN2 : Molex 26-60-4060 1, 2 V1 3, 4 DC Return 5 -Remote Sense (NC) 6 +Remote Sense Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED Mating Housing Crimp terminal/pins Molex 09-50-8031 with locking ramp Molex 6838 Series Molex 09-50-8061 with locking ramp Molex 6838 Series This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2013 Murata Power Solutions, Inc. www.murata-ps.com/support MVAD065.A01.D10 Page 5 of 5