QEB75 SERIES 75 WATTS DC-DC CONVERTER FEATURES • 75 WATTS MAXIMUM OUTPUT POWER • SINGLE OUTPUT UP TO 25A • COMPACT 2.28 X 1.45 X 0.50 INCH PACKAGE • HIGH EFFICIENCY UP TO 90% • 2:1 WIDE INPUT VOLTAGE RANGE • FIXED SWITCHING FREQUENCY • INDUSTRY STANDARD FOOTPRINT • NO MINIMUM LOAD REQUIRED • ADJUSTABLE OUTPUT VOLTAGE • UNDER-VOLTAGE LOCKOUT • INPUT TO OUTPUT ISOLATION: 1600VDC • CE MARK MEETS 2006/95/EC, 2011/95/EC AND 2004/108/EC • SAFETY MEETS UL60950-1, EN60950-1 AND IEC60950-1 • ISO9001 CERTIFIED MANUFACTURING FACILITIES • COMPLIANT TO RoHS EU DIRECTIVE 2011/65/EU APPLICATIONS Wireless Network Telecom/Datacom Industry Control System Distributed Power Architectures Semiconductor Equipment OPTIONS Positive logic Remote on/off, Pin length DESCRIPTION QEB75 single output DC/DC converters provide up to 75 watts of output power in an industry standard quarter-brick package and footprint. These units are specifically designed to meet the power needs of low-voltage silicon. All models feature a wide input range, trimmable output voltage and a 25A current rating. T E C H N I C A L S P E C I F I C AT I O N All specifications are typical at nominal input, full load and 25ºC otherwise noted OUTPUT SPECIFICATIONS INPUT SPECIFICATIONS Output power Voltage accuracy Minimum load Voltage adjustability (Note 5) Line regulation LL to HL at Full Load ±0.2% Load regulation No load to Full Load ±0.3% Remote Sense (Note 5) 10% of Vout(nom) 20MHz bandwidth See table Ripple and noise (Measured with a 1µFM/C and a 10µFT/C) ±0.02% / ºC, max. Temperature coefficient Transient response recovery time 24VDC nominal input 48VDC nominal input 75 Watts, max. Input voltage range ± 1.5% Input filter 0% + 10% , -20% Input surge voltage 25% load step change Over voltage Protection threshold (Non-latching Hiccup) 200µs 120% of Vout(nom) max. Over Current Protection threshold 110% ~ 140% of Iout Rated Short circuit protection Continuous, automatics recovery GENERAL SPECIFICATIONS Efficiency L-C type 24VDC input 50VDC 100ms, max. 48VDC input 100VDC 100ms, max. Nominal input and Power up 25ms Start up time constant resistive load Remote ON/OFF 25ms 18VDC, max. 24VDC input Start-up voltage 48VDC input 36VDC, max. 15VDC 24VDC input Shutdown voltage 48VDC input 32VDC Remote ON/OFF (Note 6) Negative logic(Standard) DC-DC ON Short or 0V < Vr < 1.2V Open or 3V < Vr < 15V DC-DC OFF Positive logic(Option) DC-DC ON Open or 3V < Vr < 15V DC-DC OFF Short or 0V < Vr < 1.2V -0.5~1.0mA Input current of remote control pin Nominal input Remote off state input current Nominal input 2.5mA ENVIRONMENTAL SPECIFICATIONS Operating base-plate temperature range (Note 7) See table Over temperature protection Input to Output 1600 VDC, min. 1minute Storage temperature range Input(Output) to Base-plate 1000 VDC, min. 1minute Thermal shock 7 Isolation resistance 500VDC 10 ohms, min. Vibration 270kHz±10% Design meets safety standard Weight (approx) MTBF (Note 1) Page 1 of 3 MIL-STD-810F BELLCORE TR-NWT-000332 MIL-HDBK-217F 5% to 95% RH EMC CHARACTERISTICS IEC60950-1, UL60950-1, EN60950-1 EMI (Note 8) Case material +110ºC MIL-STD-810F 2500 pF, max. Relative humidity(non-condensing) Switching frequency -40ºC ~ +100ºC -55ºC ~ +125ºC Isolation voltage Isolation capacitance 18 ~ 36VDC 36 ~ 75VDC Aluminum base-plate Radiated immunity Fast transient (Note 9) 42g (1.46 oz) Surge (Note 9) 6 2.500 x 10 hrs 4.422 x 105 hrs Conducted immunity www.pduke.com EN55022 Class A, Class B EN61000-4-3 10 V/m Perf. Criteria A EN61000-4-4 ± 2kV Perf. Criteria B EN61000-4-5 ± 1kV Perf. Criteria B EN61000-4-6 10 Vr.m.s Perf. Criteria A 2013/5/3 QEB75 SERIES 75 WATTS Output Current Model Number Input Range Output Voltage Min. load QEB75-24S3P3 18 ~ 36 VDC 3.3 VDC QEB75-24S05 18 ~ 36 VDC QEB75-24S12 DC-DC CONVERTER (2) (3) Full load Output Ripple & Noise No load Input Current 0mA 20A 100mVp-p 65mA 89 5 VDC 0mA 15A 100mVp-p 110mA 90 18 ~ 36 VDC 12 VDC 0mA 6.25A 100mVp-p 40mA 90 QEB75-24S15 18 ~ 36 VDC 15 VDC 0mA 5A 100mVp-p 50mA 90 QEB75-48S1P8 36 ~ 75 VDC 1.8 VDC 0mA 25A 100mVp-p 60mA 85 QEB75-48S2P5 36 ~ 75 VDC 2.5 VDC 0mA 25A 100mVp-p 50mA 87 QEB75-48S3P3 36 ~ 75 VDC 3.3 VDC 0mA 20A 100mVp-p 70mA 90 QEB75-48S05 36 ~ 75 VDC 5 VDC 0mA 15A 100mVp-p 80mA 90 QEB75-48S12 36 ~ 75 VDC 12 VDC 0mA 6.25A 100mVp-p 50mA 90 QEB75-48S15 36 ~ 75 VDC 15 VDC 0mA 5A 100mVp-p 50mA 90 Eff(%) (4) Note : 1. BELLCORE TR-NWT-000332. Case 1: 80% Stress, Temperature at 40ºC. MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment) 2. Typical value at nominal input and full load. (20MHZ BW) 3. Typical value at nominal input and no load. 4. Typical value at nominal input and full load. 5. Maximum output deviation is 10% inclusive of trim. If remote sense is not being used, the +SENSE should be connected to its corresponding +OUTPUT and likewise the -SENSE should be connected to its corresponding –OUTPUT. 6. The positive logic and pin length are optional ( see table ). The CTRL pin voltage is referenced to -INPUT. 7. Heat-sink is optional and P/N：7G-0029A-F, 7G-0030A-F, 7G-0031A-F, 7G-0032A-F. 8. The QEB75 series standard module meets EN55022 Class A and Class B with external components. For more detail information, please contact with P-DUKE. 9. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220 F/100V. 10. BASE-PLATE GROUNDING：When connect the four screw bolts to shield plane, the EMI could be reduced. 11. The converter is provided by basic insulation. μ CAUTION: This power module is not internally fused. An input line fuse must always be used. QEB75-48S05 Derating Curve With Heat-sink 7G-0029(Note 7) 120 120 100 100 OUTPUT POWER(%) OUTPUT POWER(%) QEB75-48S05 Derating Curve 80 60 Natural Convection 100LFM 200LFM 300LFM 400LFM 500LFM 24 40 20 -40 -20 ℃ 0 20 40 60 80 AMBIENT TEMPERATURE,TA( ) 100 Natural Convection 100LFM 200LFM 300LFM 400LFM 34 500LFM 40 20 -40 120 QEB75-48S05 Efficiency VS Voltage -20 0 20 40 60 80 AMBIENT TEMPERATURE,TA( ) ℃ 100 120 QEB75-48S05 Efficiency VS Output Load 93 95 92 90 EFFICIENCY(%) EFFICIENCY(%) 60 0 0 91 90 89 85 80 75 70 88 65 87 36 Page 2 of 3 80 40 44 48 52 56 60 64 INPUT VOLTAGE(V) 68 72 10 75 www.pduke.com 20 30 40 50 60 70 % of FULL LOAD 80 90 100 2013/5/3 QEB75 SERIES 75 WATTS MECHANICAL DRAWING DC-DC CONVERTER ： 1. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01(0.25) 3. Pin dimension tolerance ±0.004 (0.1) PIN CONNECTION PIN 1 2 3 4 5 6 7 8 DEFINE -INPUT CTRL +INPUT -OUTPUT -SENSE TRIM +SENSE +OUTPUT EXTERNAL OUTPUT TRIMMING DIAMETER 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.060 Inch（1.52mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.040 Inch（1.02mm） 0.060 Inch（1.52mm） Remote On/Off and Pin Options Negative remote ON/OFF logic, 0.200” pin length (standard) Negative remote ON/OFF logic, 0.145” pin length Positive remote ON/OFF logic, 0.200” pin length Positive remote ON/OFF logic, 0.145” pin length Output can be externally trimmed by using the method shown below. TRIM UP TRIM DOWN 7 6 RU 6 Suffix -L -P -S RD 5 Heat-Sink and Mounting Hole Tread Options Without heat-sink 7G-0029A-F 7G-0030A-F 7G-0031A-F 7G-0032A-F Through hole (No thread) Suffix -HS - HS1 - HS2 - HS3 -TH Example：QEB75-48S3P3-PHS * The module can’t equip heat-sink with TH option. Page 3 of 3 www.pduke.com 2013/5/3