SF2024D-1 ® • • • • • Designed for SDARS Receiver IF Application Low Insertion Loss 3.8 X 3.8 X 1.0 mm Surface-Mount Case Differential Input and Output Complies with Directive 2002/95/EC (RoHS) 467.751 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Max. DC voltage between any 2 terminals 30 VDC Storage Temperature Range -40 to +85 Suitable for lead-free soldering - Max Soldering Profile °C SM3838-8 260°C for 30 s Electrical Characteristics Characteristic Center Frequency Insertion Loss Amplitude Ripple (p-p) Sym fC IL fc-6.250 to fc-4.3925 MHz fc-4.3925 to fc-2.535 MHz fc-2.5350 to fc-0.025 MHz fc+0.025 to fc+2.535 MHz fc+2.5350 to fc+4.3925 MHz fc+4.3925 to fc+6.250 MHz Pass bandwidth of -2.0dB centered at fc Pass bandwidth of -3 dB Low Side Attenuation between 455.751 to 457.251 MHz (fc-10.5 MHz) Low Side Attenuation F<455.751 MHz High Side Attenuation between 476.751 to 479.751 MHz (fc+9.0 MHz) High Side Attenuation F>479.751 MHz Temperature Coefficient of frequency Delay Ripple (p-p) fc-6.250 to fc-4.3925 MHz fc-4.3925 to fc-2.535 MHz fc-2.5350 to fc-0.025 MHz fc+0.025 to fc+2.535 MHz fc+2.5350 to fc+4.3925 MHz fc+4.3925 to fc+6.250 MHz Source Impedance Load Impedance Case Style Lid Symbolization (YY=year, WW=week, S=shift) See note 4 Operating Temperature Notes: 1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. 2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. 4. The design, manufacturing process, and specifications of this filter are subject to change. Notes 1 Min 467.704 1, 2 Typ 467.751 13 0.7 0.8 0.9 1.1 1.1 1.2 13.0 Max 467.798 15.5 2.0 2.0 2.0 2.0 2.0 2.0 Units MHz dB dB MHz 32 32 20 32 1, 2, 3 ZS ZL 6 5. 6. 7. 8. dB -18 ppm/K 70 110 70 140 75 120 ns 80 120 80 100 85 140 150 Ω 150 Ω SM3838-8 3.8 x 3.8 mm Nominal Footprint 619 YWWS -40 +85 °C Tape and Reel Standard Per ANSI / EIA 481. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. ©Copyright 1999, RF Monolithics Inc. Electrostatic Sensitive Device. Observe precautions for handling. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF2024D-1-1/29/08 Ver 0.1 Page 1 of 5 467.751 MHz SAW Filter RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF2024D-1-1/29/08 Ver 0.1 Page 2 of 5 467.751 MHz SAW Filter RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF2024D-1-1/29/08 Ver 0.1 Page 3 of 5 467.751 MHz SAW Filter SM3838-8-Thin Case 8-Terminal Ceramic Surface-Mount Case 3.8 X 3.8 mm Nominal Footprint Case Dimensions A B C D E F G H 0.066 (1.68) Min 3.6 3.6 0.90 0.80 0.90 0.50 2.39 1.40 mm Nom 3.8 3.8 1.00 0.90 1.00 0.60 2.54 1.75 Max 4.0 4.0 1.1 1.0 1.10 0.70 2.69 2.05 Min 0.142 0.142 0.035 0.031 0.035 0.020 0.090 0.055 Inches Nom 0.150 0.150 0.040 0.035 0.040 0.024 0.100 0.069 Max 0.157 0.157 0.043 0.040 0.043 0.028 0.110 0.080 Electrical Connections 0.090 (2.29) Connection Differential Input Differential Output Ground Single Ended Operation Differential Operation Dot Indicates Pin 1 Terminals 1, 2 5, 6 All Others Return is Ground Return is Hot Port 1 Port 2 0.033 (0.84) 0.002 (0.05) 0.050 TYP. (1.27) 0.029 TYP. (O.74) Dimension Materials 0.055 TYP. (1.40) PCB Footprint Solder Pad Termination Au plating 30 - 60 uInches (76.2-152 uM) over 80-200 uInches (203-508 uM) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 uInches Thick Body Al2O3 Ceramic Pb Free TOP VIEW BOTTOM VIEW 2 3 8 619 A YWWS 1 E C B 8 7 H 7 1 6 6 2 5 5 3 4 4 D RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. G F E-mail: [email protected] http://www.rfm.com SF2024D-1-1/29/08 Ver 0.1 Page 4 of 5 467.751 MHz SAW Filter “B “ Nominal Size "B" REF. 100 REF. Tape and Reel Specifications Quantity Per Reel Inches millimeters 7 178 500 13 330 3000 See Detail "A" 13. 0 12.0 .2 20 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions 2.0 4.25 mm Bo 4.25 mm Ko 1.30 mm Pitch 8.0 mm W 12.0 mm 4.0 PIN #1 A 1.50 1.75 0.3 ± 0.05 Ao Bo B Ao 12.0 5.5 RO.3 (MAX.) B Pitch A Ko R0.5 (MAX.) 1.5 SECTION A-A SECTION B-B RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. USER DIRECTION OF FEED E-mail: [email protected] http://www.rfm.com SF2024D-1-1/29/08 Ver 0.1 Page 5 of 5