SILICONIMAGE EFM32ZG108F16

Preliminary
...the world's most energy friendly microcontrollers
EFM32ZG108 DATASHEET
F32/F16/F8/F4
Preliminary
• ARM Cortex-M0+ CPU platform
• High Performance 32-bit processor @ up to 24 MHz
• Wake-up Interrupt Controller
• Flexible Energy Management System
• 20 nA @ 3 V Shutoff Mode
• 0.5 µA @ 3 V Stop Mode, including Power-on Reset, Brown-out
Detector, RAM and CPU retention
• 0.9 µA @ 3 V Deep Sleep Mode, including RTC with 32.768 kHz
oscillator, Power-on Reset, Brown-out Detector, RAM and CPU
retention
• 46 µA/MHz @ 3 V Sleep Mode
• 114 µA/MHz @ 3 V Run Mode, with code executed from flash
• 32/16/8/4 KB Flash
• 4/4/2/2 KB RAM
• 17 General Purpose I/O pins
• Configurable push-pull, open-drain, pull-up/down, input filter, drive
strength
• Configurable peripheral I/O locations
• 11 asynchronous external interrupts
• Output state retention and wake-up from Shutoff Mode
• 4 Channel DMA Controller
• 4 Channel Peripheral Reflex System (PRS) for autonomous inter-peripheral signaling
• Timers/Counters
• 2× 16-bit Timer/Counter
• 2×3 Compare/Capture/PWM channels
• 1× 24-bit Real-Time Counter
• 1× 16-bit Pulse Counter
• Watchdog Timer with dedicated RC oscillator @ 50 nA
• Communication interfaces
• 1× Universal Synchronous/Asynchronous Receiver/Transmitter
• UART/SPI/SmartCard (ISO 7816)/IrDA/I2S
• Triple buffered full/half-duplex operation
• Low Energy UART
• Autonomous operation with DMA in Deep Sleep
Mode
2
• I C Interface with SMBus support
• Address recognition in Stop Mode
• Ultra low power precision analog peripherals
• 1× Analog Comparator
• Capacitive sensing with up to 2 inputs
• Supply Voltage Comparator
• Ultra efficient Power-on Reset and Brown-Out Detector
• 2-pin Serial Wire Debug interface
• Pre-Programmed UART Bootloader
• Temperature range -40 to 85 ºC
• Single power supply 1.85 to 3.8 V
• QFN24 package
32-bit ARM Cortex-M0+, Cortex-M3 and Cortex-M4 microcontrollers for:
• Energy, gas, water and smart metering
• Health and fitness applications
• Smart accessories
• Alarm and security systems
• Industrial and home automation
• www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
1 Ordering Information
Table 1.1 (p. 2) shows the available EFM32ZG108 devices.
Table 1.1. Ordering Information
Ordering Code
Flash (kB)
RAM (kB)
Max
Speed
(MHz)
Supply
Voltage
(V)
Temperature
(ºC)
Package
EFM32ZG108F4-QFN24
4
2
24
1.85 - 3.8
-40 - 85
QFN24
EFM32ZG108F8-QFN24
8
2
24
1.85 - 3.8
-40 - 85
QFN24
EFM32ZG108F16-QFN24
16
4
24
1.85 - 3.8
-40 - 85
QFN24
EFM32ZG108F32-QFN24
32
4
24
1.85 - 3.8
-40 - 85
QFN24
Visit www.silabs.com for information on global distributors and representatives.
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
2
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
2 System Summary
2.1 System Introduction
The EFM32 MCUs are the world’s most energy friendly microcontrollers. With a unique combination
of the powerful 32-bit ARM Cortex-M0+, innovative low energy techniques, short wake-up time from
energy saving modes, and a wide selection of peripherals, the EFM32ZG microcontroller is well suited
for any battery operated application as well as other systems requiring high performance and low-energy
consumption. This section gives a short introduction to each of the modules in general terms and also
shows a summary of the configuration for the EFM32ZG108 devices. For a complete feature set and indepth information on the modules, the reader is referred to the EFM32ZG Reference Manual.
A block diagram of the EFM32ZG108 is shown in Figure 2.1 (p. 3) .
Figure 2.1. Block Diagram
ZG108F32/ 16/ 8/ 4
Core and Mem ory
ARM Cortex ™ M0+ processor
Flash
Program
Mem ory
RAM
Mem ory
Debug
Interface
Clock Managem ent
Energy Managem ent
High Freq
Crystal
Oscillator
High Freq
RC
Oscillator
Voltage
Regulator
Voltage
Com parator
Low Freq
Crystal
Oscillator
Low Freq
RC
Oscillator
Brown- out
Detector
Power- on
Reset
DMA
Controller
Ultra Low Freq
RC
Oscillator
32- bit bus
Peripheral Ref lex Syst em
Serial Interfaces
USART
Low
Energy
Uart™
2
IC
I/ O Ports
Tim ers and Triggers
Analog Interfaces
Ex ternal
Interrupts
General
Purpose
I/ O
Tim er/
Counter
Real Tim e
Counter
Analog
Com parator
Pin
Reset
Pin
Wakeup
Pulse
Counter
Watchdog
Tim er
2.1.1 ARM Cortex-M0+ Core
The ARM Cortex-M0+ includes a 32-bit RISC processor which can achieve as much as 0.9 Dhrystone
MIPS/MHz. A Wake-up Interrupt Controller handling interrupts triggered while the CPU is asleep is included as well. The EFM32 implementation of the Cortex-M0+ is described in detail in ARM Cortex-M0+
Devices Generic User Guide.
2.1.2 Debug Interface (DBG)
This device includes hardware debug support through a 2-pin serial-wire debug interface.
2.1.3 Memory System Controller (MSC)
The Memory System Controller (MSC) is the program memory unit of the EFM32ZG microcontroller.
The flash memory is readable and writable from both the Cortex-M0+ and DMA. The flash memory is
divided into two blocks; the main block and the information block. Program code is normally written to
the main block. Additionally, the information block is available for special user data and flash lock bits.
There is also a read-only page in the information block containing system and device calibration data.
Read and write operations are supported in the energy modes EM0 and EM1.
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
3
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
2.1.4 Direct Memory Access Controller (DMA)
The Direct Memory Access (DMA) controller performs memory operations independently of the CPU.
This has the benefit of reducing the energy consumption and the workload of the CPU, and enables
the system to stay in low energy modes when moving for instance data from the USART to RAM or
from the External Bus Interface to a PWM-generating timer. The DMA controller uses the PL230 µDMA
controller licensed from ARM.
2.1.5 Reset Management Unit (RMU)
The RMU is responsible for handling the reset functionality of the EFM32ZG.
2.1.6 Energy Management Unit (EMU)
The Energy Management Unit (EMU) manage all the low energy modes (EM) in EFM32ZG microcontrollers. Each energy mode manages if the CPU and the various peripherals are available. The EMU
can also be used to turn off the power to unused SRAM blocks.
2.1.7 Clock Management Unit (CMU)
The Clock Management Unit (CMU) is responsible for controlling the oscillators and clocks on-board
the EFM32ZG. The CMU provides the capability to turn on and off the clock on an individual basis to all
peripheral modules in addition to enable/disable and configure the available oscillators. The high degree
of flexibility enables software to minimize energy consumption in any specific application by not wasting
power on peripherals and oscillators that are inactive.
2.1.8 Watchdog (WDOG)
The purpose of the watchdog timer is to generate a reset in case of a system failure, to increase application reliability. The failure may e.g. be caused by an external event, such as an ESD pulse, or by a
software failure.
2.1.9 Peripheral Reflex System (PRS)
The Peripheral Reflex System (PRS) system is a network which lets the different peripheral module
communicate directly with each other without involving the CPU. Peripheral modules which send out
Reflex signals are called producers. The PRS routes these reflex signals to consumer peripherals which
apply actions depending on the data received. The format for the Reflex signals is not given, but edge
triggers and other functionality can be applied by the PRS.
2.1.10 Inter-Integrated Circuit Interface (I2C)
2
2
The I C module provides an interface between the MCU and a serial I C-bus. It is capable of acting as
both a master and a slave, and supports multi-master buses. Both standard-mode, fast-mode and fastmode plus speeds are supported, allowing transmission rates all the way from 10 kbit/s up to 1 Mbit/s.
Slave arbitration and timeouts are also provided to allow implementation of an SMBus compliant system.
2
The interface provided to software by the I C module, allows both fine-grained control of the transmission
process and close to automatic transfers. Automatic recognition of slave addresses is provided in all
energy modes.
2.1.11 Universal Synchronous/Asynchronous Receiver/Transmitter (USART)
The Universal Synchronous Asynchronous serial Receiver and Transmitter (USART) is a very flexible
serial I/O module. It supports full duplex asynchronous UART communication as well as RS-485, SPI,
MicroWire and 3-wire. It can also interface with ISO7816 SmartCards, IrDA and I2S devices.
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
4
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
2.1.12 Pre-Programmed UART Bootloader
The bootloader presented in application note AN0003 is pre-programmed in the device at factory. Autobaud and destructive write are supported. The autobaud feature, interface and commands are described
further in the application note.
2.1.13 Low Energy Universal Asynchronous Receiver/Transmitter
(LEUART)
TM
The unique LEUART , the Low Energy UART, is a UART that allows two-way UART communication on
a strict power budget. Only a 32.768 kHz clock is needed to allow UART communication up to 9600 baud/
s. The LEUART includes all necessary hardware support to make asynchronous serial communication
possible with minimum of software intervention and energy consumption.
2.1.14 Timer/Counter (TIMER)
The 16-bit general purpose Timer has 3 compare/capture channels for input capture and compare/PulseWidth Modulation (PWM) output.
2.1.15 Real Time Counter (RTC)
The Real Time Counter (RTC) contains a 24-bit counter and is clocked either by a 32.768 kHz crystal
oscillator, or a 32.768 kHz RC oscillator. In addition to energy modes EM0 and EM1, the RTC is also
available in EM2. This makes it ideal for keeping track of time since the RTC is enabled in EM2 where
most of the device is powered down.
2.1.16 Pulse Counter (PCNT)
The Pulse Counter (PCNT) can be used for counting pulses on a single input or to decode quadrature
encoded inputs. It runs off either the internal LFACLK or the PCNTn_S0IN pin as external clock source.
The module may operate in energy mode EM0 – EM3.
2.1.17 Analog Comparator (ACMP)
The Analog Comparator is used to compare the voltage of two analog inputs, with a digital output indicating which input voltage is higher. Inputs can either be one of the selectable internal references or from
external pins. Response time and thereby also the current consumption can be configured by altering
the current supply to the comparator.
2.1.18 Voltage Comparator (VCMP)
The Voltage Supply Comparator is used to monitor the supply voltage from software. An interrupt can
be generated when the supply falls below or rises above a programmable threshold. Response time and
thereby also the current consumption can be configured by altering the current supply to the comparator.
2.1.19 General Purpose Input/Output (GPIO)
In the EFM32ZG108, there are 17 General Purpose Input/Output (GPIO) pins, which are divided into
ports with up to 16 pins each. These pins can individually be configured as either an output or input. More
advanced configurations like open-drain, filtering and drive strength can also be configured individually
for the pins. The GPIO pins can also be overridden by peripheral pin connections, like Timer PWM
outputs or USART communication, which can be routed to several locations on the device. The GPIO
supports up to 16 asynchronous external pin interrupts, which enables interrupts from any pin on the
device. Also, the input value of a pin can be routed through the Peripheral Reflex System to other
peripherals.
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
5
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
2.2 Configuration Summary
The features of the EFM32ZG108 is a subset of the feature set described in the EFM32ZG Reference
Manual. Table 2.1 (p. 6) describes device specific implementation of the features.
Table 2.1. Configuration Summary
Module
Configuration
Pin Connections
Cortex-M0+
Full configuration
NA
DBG
Full configuration
DBG_SWCLK, DBG_SWDIO,
MSC
Full configuration
NA
DMA
Full configuration
NA
RMU
Full configuration
NA
EMU
Full configuration
NA
CMU
Full configuration
CMU_OUT0, CMU_OUT1
WDOG
Full configuration
NA
PRS
Full configuration
NA
I2C0
Full configuration
I2C0_SDA, I2C0_SCL
USART0
Full configuration with IrDA and I2S
US0_TX, US0_RX. US0_CLK, US0_CS
LEUART0
Full configuration
LEU0_TX, LEU0_RX
TIMER0
Full configuration
TIM0_CC[2:0]
TIMER1
Full configuration
TIM1_CC[2:0]
RTC
Full configuration
NA
PCNT0
Full configuration, 16-bit count register
PCNT0_S[1:0]
ACMP0
Full configuration
ACMP0_CH[1:0], ACMP0_O
VCMP
Full configuration
NA
GPIO
17 pins
Available pins are shown in
Table 4.3 (p. 37)
2.3 Memory Map
The EFM32ZG108 memory map is shown in Figure 2.2 (p. 7) , with RAM and Flash sizes for the
largest memory configuration.
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
6
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Figure 2.2. EFM32ZG108 Memory Map with largest RAM and Flash sizes
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
7
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
3 Electrical Characteristics
3.1 Test Conditions
3.1.1 Typical Values
The typical data are based on TAMB=25°C and VDD=3.0 V, as defined in Table 3.2 (p. 8) , by simulation and/or technology characterisation unless otherwise specified.
3.1.2 Minimum and Maximum Values
The minimum and maximum values represent the worst conditions of ambient temperature, supply voltage and frequencies, as defined in Table 3.2 (p. 8), by simulation and/or technology characterisation unless otherwise specified.
3.2 Absolute Maximum Ratings
The absolute maximum ratings are stress ratings, and functional operation under such conditions are
not guaranteed. Stress beyond the limits specified in Table 3.1 (p. 8) may affect the device reliability
or cause permanent damage to the device. Functional operating conditions are given in Table 3.2 (p.
8) .
Table 3.1. Absolute Maximum Ratings
Symbol
Parameter
Condition
Min
Typ
Max
-40
Unit
150
1
TSTG
Storage temperature range
TS
Maximum soldering
temperature
VDDMAX
External main supply voltage
0
3.8 V
VIOPIN
Voltage on any I/O
pin
-0.3
VDD+0.3 V
Latest IPC/JEDEC J-STD-020
Standard
°C
260 °C
1
Based on programmed devices tested for 10000 hours at 150ºC. Storage temperature affects retention of preprogrammed calibration values stored in flash. Please refer to the Flash section in the Electrical Characteristics for information on flash data retention for different temperatures.
3.3 General Operating Conditions
3.3.1 General Operating Conditions
Table 3.2. General Operating Conditions
Symbol
Parameter
TAMB
Ambient temperature range
VDDOP
Operating supply voltage
fAPB
Internal APB clock frequency
24 MHz
fAHB
Internal AHB clock frequency
24 MHz
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
Min
Typ
-40
1.85
8
Max
Unit
85 °C
3.8 V
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
3.4 Current Consumption
Table 3.3. Current Consumption
Symbol
IEM0
IEM1
IEM2
IEM3
IEM4
Parameter
EM0 current. No
prescaling. Running
prime number calculation code from
Flash.
Condition
Min
Typ
Max
Unit
24 MHz HFXO, all peripheral
clocks disabled, VDD= 3.0 V
114.9
µA/
MHz
21 MHz HFRCO, all peripheral
clocks disabled, VDD= 3.0 V
114.4
µA/
MHz
14 MHz HFRCO, all peripheral
clocks disabled, VDD= 3.0 V
116.6
µA/
MHz
11 MHz HFRCO, all peripheral
clocks disabled, VDD= 3.0 V
118.2
µA/
MHz
6.6 MHz HFRCO, all peripheral
clocks disabled, VDD= 3.0 V
123.5
µA/
MHz
1.2 MHz HFRCO, all peripheral
clocks disabled, VDD= 3.0 V
155.1
µA/
MHz
24 MHz HFXO, all peripheral
clocks disabled, VDD= 3.0 V
48.0
µA/
MHz
21 MHz HFRCO, all peripheral
clocks disabled, VDD= 3.0 V
48.1
µA/
MHz
14 MHz HFRCO, all peripheral
clocks disabled, VDD= 3.0 V
50.1
µA/
MHz
11 MHz HFRCO, all peripheral
clocks disabled, VDD= 3.0 V
51.8
µA/
MHz
6.6 MHz HFRCO, all peripheral
clocks disabled, VDD= 3.0 V
57.1
µA/
MHz
1.2 MHz HFRCO. all peripheral
clocks disabled, VDD= 3.0 V
89.1
µA/
MHz
EM2 current with RTC at 1
Hz, RTC prescaled to 1kHz,
32.768 kHz LFRCO, VDD= 3.0
V, TAMB=25°C
0.86
µA
EM2 current with RTC at 1
Hz, RTC prescaled to 1kHz,
32.768 kHz LFRCO, VDD= 3.0
V, TAMB=85°C
1.66
µA
VDD= 3.0 V, TAMB=25°C
0.49
µA
VDD= 3.0 V, TAMB=85°C
1.26
µA
VDD= 3.0 V, TAMB=25°C
0.02
µA
VDD= 3.0 V, TAMB=85°C
0.29
µA
EM1 current
EM2 current
EM3 current
EM4 current
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
9
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
3.4.1 EM0 Current Consumption
Figure 3.1. EM0 Current consumption while executing prime number calculation code from flash
with HFRCO running at 24MHz
2.84
2.80
Idd [m A]
2.78
2.82
2.80
2.78
Idd [m A]
2.82
2.84
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
2.76
2.76
2.74
2.74
2.72
2.72
2.70
2.70
2.68
2.0
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
3.4
3.6
2.68
–40
3.8
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
–15
5
25
Tem perature [°C]
45
65
85
Figure 3.2. EM0 Current consumption while executing prime number calculation code from flash
with HFRCO running at 21MHz
2.40
2.40
Idd [m A]
2.45
Idd [m A]
2.45
2.35
2.35
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
2.30
2.0
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
3.4
3.6
2.30
3.8
–40
10
–15
5
25
Tem perature [°C]
45
65
85
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
1.68
1.68
1.66
1.66
1.64
1.64
1.62
1.62
Idd [m A]
Idd [m A]
Figure 3.3. EM0 Current consumption while executing prime number calculation code from flash
with HFRCO running at 14MHz
1.60
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
1.58
1.56
1.54
2.0
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
3.4
3.6
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
1.60
1.58
1.56
1.54
–40
3.8
–15
5
25
Tem perature [°C]
45
65
85
1.34
1.34
1.32
1.32
1.30
1.30
Idd [m A]
Idd [m A]
Figure 3.4. EM0 Current consumption while executing prime number calculation code from flash
with HFRCO running at 11MHz
1.28
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
1.26
1.24
1.22
2.0
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
3.4
3.6
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
1.28
1.26
1.24
1.22
–40
3.8
11
–15
5
25
Tem perature [°C]
45
65
85
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
0.84
0.84
0.83
0.83
0.82
0.82
0.81
0.81
Idd [m A]
Idd [m A]
Figure 3.5.
0.80
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
0.79
0.78
0.77
2.0
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
3.4
3.6
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
0.80
0.79
0.78
0.77
–40
3.8
–15
5
25
Tem perature [°C]
45
65
85
3.4.2 EM1 Current Consumption
Figure 3.6. EM1 Current consumption with all peripheral clocks disabled and HFRCO running
at 24MHz
1.20
1.18
1.20
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
1.18
Idd [m A]
1.16
Idd [m A]
1.16
1.14
1.14
1.12
1.12
1.10
2.0
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
3.4
3.6
1.10
–40
3.8
12
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
–15
5
25
Tem perature [°C]
45
65
85
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
1.04
1.04
1.03
1.03
1.02
1.02
1.01
1.01
Idd [m A]
Idd [m A]
Figure 3.7. EM1 Current consumption with all peripheral clocks disabled and HFRCO running
at 21MHz
1.00
0.99
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
0.98
0.97
0.96
0.95
2.0
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
3.4
3.6
1.00
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
0.99
0.98
0.97
0.96
0.95
–40
3.8
–15
5
25
Tem perature [°C]
45
65
85
0.73
0.73
0.72
0.72
0.71
0.71
0.70
0.70
Idd [m A]
Idd [m A]
Figure 3.8. EM1 Current consumption with all peripheral clocks disabled and HFRCO running
at 14MHz
0.69
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
0.68
0.67
0.66
2.0
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
3.4
3.6
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
0.69
0.68
0.67
0.66
–40
3.8
13
–15
5
25
Tem perature [°C]
45
65
85
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
0.59
0.59
0.58
0.58
0.57
0.57
Idd [m A]
Idd [m A]
Figure 3.9. EM1 Current consumption with all peripheral clocks disabled and HFRCO running
at 11MHz
0.56
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
0.55
0.54
0.53
2.0
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
3.4
3.6
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
0.56
0.55
0.54
0.53
–40
3.8
–15
5
25
Tem perature [°C]
45
65
85
0.395
0.395
0.390
0.390
0.385
0.385
0.380
0.380
Idd [m A]
Idd [m A]
Figure 3.10.
0.375
0.370
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
0.365
0.360
0.355
0.350
2.0
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
3.4
3.6
0.375
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
0.370
0.365
0.360
0.355
0.350
–40
3.8
14
–15
5
25
Tem perature [°C]
45
65
85
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
3.4.3 EM2 Current Consumption
Figure 3.11. EM2 current consumption. RTC prescaled to 1kHz, 32.768 kHz LFRCO.
2.0
2.0
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
1.8
1.6
1.4
Idd [uA]
Idd [uA]
1.6
1.8
1.2
1.4
1.2
1.0
1.0
0.8
0.8
0.6
2.0
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
3.4
3.6
0.6
–40
3.8
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
–15
5
25
Tem perature [°C]
45
65
85
5
25
Tem perature [°C]
45
65
85
3.4.4 EM3 Current Consumption
Figure 3.12. EM3 current consumption.
1.6
1.6
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
1.4
1.2
Idd [uA]
Idd [uA]
1.2
1.4
1.0
1.0
0.8
0.8
0.6
0.6
0.4
2.0
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
3.4
3.6
0.4
–40
3.8
15
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
–15
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
3.4.5 EM4 Current Consumption
Figure 3.13. EM4 current consumption.
0.5
Idd [uA]
0.3
0.4
0.3
Idd [uA]
0.4
0.5
- 40.0°C
- 15.0°C
5.0°C
25.0°C
45.0°C
65.0°C
85.0°C
0.2
0.2
0.1
0.1
0.0
0.0
–0.1
2.0
2.2
2.4
2.6
2.8
3.0
Vdd [V]
3.2
3.4
3.6
Vdd= 2.0V
Vdd= 2.2V
Vdd= 2.4V
Vdd= 2.6V
Vdd= 2.8V
Vdd= 3.0V
Vdd= 3.2V
Vdd= 3.4V
Vdd= 3.6V
Vdd= 3.8V
–0.1
–40
3.8
–15
5
25
Tem perature [°C]
45
65
85
3.5 Transition between Energy Modes
Table 3.4. Energy Modes Transitions
Symbol
Parameter
tEM10
Transition time from EM1 to EM0
tEM20
Min
Typ
Max
Unit
1
HF
core
CLK
cycles
Transition time from EM2 to EM0
2
µs
tEM30
Transition time from EM3 to EM0
2
µs
tEM40
Transition time from EM4 to EM0
163
µs
0
1
Core wakeup time only.
3.6 Power Management
The EFM32ZG requires the AVDD_x, VDD_DREG and IOVDD_x pins to be connected together (with
optional filter) at the PCB level. For practical schematic recommendations, please see the application
note, "AN0002 EFM32 Hardware Design Considerations".
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
16
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Table 3.5. Power Management
Symbol
Parameter
Condition
Min
Typ
Max
Unit
VBODextthr-
BOD threshold on
falling external supply voltage
1.82
1.85 V
VBODintthr-
BOD threshold on
falling internally regulated supply voltage
1.62
1.68 V
VBODextthr+
BOD threshold on
rising external supply voltage
tRESET
Delay from reset
is released until
program execution
starts
CDECOUPLE
Voltage regulator
decoupling capacitor.
1.85
V
Applies to Power-on Reset,
Brown-out Reset and pin reset.
163
µs
X5R capacitor recommended.
Apply between DECOUPLE pin
and GROUND
1
µF
3.7 Flash
Table 3.6. Flash
Symbol
Parameter
ECFLASH
Flash erase cycles
before failure
Condition
Min
TAMB<150°C
RETFLASH
Flash data retention
Typ
Max
Unit
20000
cycles
10000
h
TAMB<85°C
10
years
TAMB<70°C
20
years
µs
tW_PROG
Word (32-bit) programming time
20
tP_ERASE
Page erase time
20
20.4
20.8 ms
tD_ERASE
Device erase time
40
40.8
41.6 ms
IERASE
Erase current
7
1
mA
IWRITE
Write current
7
1
mA
VFLASH
Supply voltage during flash erase and
write
1.8
3.8 V
1
Measured at 25°C
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
17
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
3.8 General Purpose Input Output
Table 3.7. GPIO
Symbol
Parameter
VIOIL
Input low voltage
VIOIH
Input high voltage
VIOOH
VIOOL
Condition
Min
Typ
Max
Unit
0.3VDD V
0.7VDD
V
Sourcing 6 mA, VDD=1.85 V,
GPIO_Px_CTRL DRIVEMODE
= STANDARD
0.75VDD
V
Sourcing 6 mA, VDD=3.0 V,
GPIO_Px_CTRL DRIVEMODE
= STANDARD
0.95VDD
V
Sourcing 20 mA, VDD=1.85 V,
GPIO_Px_CTRL DRIVEMODE
= HIGH
0.7VDD
V
Sourcing 20 mA, VDD=3.0 V,
GPIO_Px_CTRL DRIVEMODE
= HIGH
0.9VDD
V
Output high voltage
Sinking 6 mA, VDD=1.85 V,
GPIO_Px_CTRL DRIVEMODE
= STANDARD
0.25VDD V
Sinking 6 mA, VDD=3.0 V,
GPIO_Px_CTRL DRIVEMODE
= STANDARD
0.05VDD V
Sinking 20 mA, VDD=1.85 V,
GPIO_Px_CTRL DRIVEMODE
= HIGH
0.3VDD V
Sinking 20 mA, VDD=3.0 V,
GPIO_Px_CTRL DRIVEMODE
= HIGH
0.1VDD V
Output low voltage
IIOLEAK
Input leakage current
RPU
I/O pin pull-up resistor
40
kOhm
RPD
I/O pin pull-down resistor
40
kOhm
RIOESD
Internal ESD series
resistor
200
Ohm
tIOGLITCH
Pulse width of pulses to be removed
by the glitch suppression filter
tIOOF
VIOHYST
High Impedance IO connected
to GROUND or Vdd
+/-25 nA
10
50 ns
0.5 mA drive strength and load
capacitance CL=12.5-25pF.
20+0.1CL
250 ns
2mA drive strength and load
capacitance CL=350-600pF
20+0.1CL
250 ns
Output fall time
I/O pin hysteresis
(VIOTHR+ - VIOTHR-)
VDD = 1.85 - 3.8 V
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
0.1VDD
18
V
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Figure 3.14. Typical Low-Level Output Current, 2V Supply Voltage
5
0.20
4
Low- Level Output Current [m A]
Low- Level Output Current [m A]
0.15
0.10
3
2
0.05
1
- 40°C
25°C
85°C
0.00
0.0
0.5
1.5
1.0
Low- Level Output Voltage [V]
- 40°C
25°C
85°C
0
0.0
2.0
GPIO_Px_CTRL DRIVEMODE = LOWEST
0.5
1.5
1.0
Low- Level Output Voltage [V]
2.0
GPIO_Px_CTRL DRIVEMODE = LOW
45
20
40
35
Low- Level Output Current [m A]
Low- Level Output Current [m A]
15
10
30
25
20
15
5
10
5
- 40°C
25°C
85°C
0
0.0
0.5
1.5
1.0
Low- Level Output Voltage [V]
0
0.0
2.0
GPIO_Px_CTRL DRIVEMODE = STANDARD
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
- 40°C
25°C
85°C
0.5
1.5
1.0
Low- Level Output Voltage [V]
2.0
GPIO_Px_CTRL DRIVEMODE = HIGH
19
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Figure 3.15. Typical High-Level Output Current, 2V Supply Voltage
0.00
0.0
- 40°C
25°C
85°C
- 40°C
25°C
85°C
–0.5
High- Level Output Current [m A]
High- Level Output Current [m A]
–0.05
–0.10
–1.0
–1.5
–0.15
–2.0
–0.20
0.0
1.5
0.5
1.0
High- Level Output Voltage [V]
–2.5
0.0
2.0
GPIO_Px_CTRL DRIVEMODE = LOWEST
1.5
0.5
1.0
High- Level Output Voltage [V]
2.0
GPIO_Px_CTRL DRIVEMODE = LOW
0
0
- 40°C
25°C
85°C
- 40°C
25°C
85°C
–10
High- Level Output Current [m A]
High- Level Output Current [m A]
–5
–10
–20
–30
–15
–40
–20
0.0
1.5
0.5
1.0
High- Level Output Voltage [V]
–50
0.0
2.0
GPIO_Px_CTRL DRIVEMODE = STANDARD
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
1.5
0.5
1.0
High- Level Output Voltage [V]
2.0
GPIO_Px_CTRL DRIVEMODE = HIGH
20
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
0.5
10
0.4
8
Low- Level Output Current [m A]
Low- Level Output Current [m A]
Figure 3.16. Typical Low-Level Output Current, 3V Supply Voltage
0.3
0.2
0.1
6
4
2
- 40°C
25°C
85°C
0.0
0.0
0.5
1.5
1.0
2.0
Low- Level Output Voltage [V]
2.5
- 40°C
25°C
85°C
0
0.0
3.0
GPIO_Px_CTRL DRIVEMODE = LOWEST
0.5
1.5
1.0
2.0
Low- Level Output Voltage [V]
2.5
3.0
GPIO_Px_CTRL DRIVEMODE = LOW
40
50
35
40
Low- Level Output Current [m A]
Low- Level Output Current [m A]
30
25
20
15
30
20
10
10
5
0
0.0
- 40°C
25°C
85°C
0.5
1.5
1.0
2.0
Low- Level Output Voltage [V]
2.5
- 40°C
25°C
85°C
0
0.0
3.0
GPIO_Px_CTRL DRIVEMODE = STANDARD
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
0.5
1.5
1.0
2.0
Low- Level Output Voltage [V]
2.5
3.0
GPIO_Px_CTRL DRIVEMODE = HIGH
21
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Figure 3.17. Typical High-Level Output Current, 3V Supply Voltage
0.0
0
- 40°C
25°C
85°C
- 40°C
25°C
85°C
–1
High- Level Output Current [m A]
High- Level Output Current [m A]
–0.1
–0.2
–0.3
–2
–3
–4
–0.4
–5
–0.5
0.0
0.5
1.5
1.0
2.0
High- Level Output Voltage [V]
2.5
–6
0.0
3.0
GPIO_Px_CTRL DRIVEMODE = LOWEST
2.5
3.0
0
- 40°C
25°C
85°C
- 40°C
25°C
85°C
–10
High- Level Output Current [m A]
–10
High- Level Output Current [m A]
1.5
1.0
2.0
High- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = LOW
0
–20
–30
–40
–50
0.0
0.5
–20
–30
–40
0.5
1.5
1.0
2.0
High- Level Output Voltage [V]
2.5
–50
0.0
3.0
GPIO_Px_CTRL DRIVEMODE = STANDARD
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
0.5
1.5
1.0
2.0
High- Level Output Voltage [V]
2.5
3.0
GPIO_Px_CTRL DRIVEMODE = HIGH
22
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Figure 3.18. Typical Low-Level Output Current, 3.8V Supply Voltage
0.8
14
0.7
12
Low- Level Output Current [m A]
Low- Level Output Current [m A]
0.6
0.5
0.4
0.3
10
8
6
4
0.2
2
0.1
0.0
0.0
- 40°C
25°C
85°C
0.5
1.5
1.0
2.0
2.5
Low- Level Output Voltage [V]
3.0
- 40°C
25°C
85°C
0
0.0
3.5
1.5
1.0
2.0
2.5
Low- Level Output Voltage [V]
3.0
50
50
40
40
30
20
10
30
20
10
- 40°C
25°C
85°C
0
0.0
3.5
GPIO_Px_CTRL DRIVEMODE = LOW
Low- Level Output Current [m A]
Low- Level Output Current [m A]
GPIO_Px_CTRL DRIVEMODE = LOWEST
0.5
0.5
1.5
1.0
2.0
2.5
Low- Level Output Voltage [V]
3.0
- 40°C
25°C
85°C
0
0.0
3.5
GPIO_Px_CTRL DRIVEMODE = STANDARD
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
0.5
1.5
1.0
2.0
2.5
Low- Level Output Voltage [V]
3.0
3.5
GPIO_Px_CTRL DRIVEMODE = HIGH
23
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Figure 3.19. Typical High-Level Output Current, 3.8V Supply Voltage
0.0
–0.1
0
- 40°C
25°C
85°C
–1
- 40°C
25°C
85°C
–2
High- Level Output Current [m A]
High- Level Output Current [m A]
–0.2
–0.3
–0.4
–0.5
–3
–4
–5
–6
–0.6
–7
–0.7
–0.8
0.0
–8
0.5
1.5
1.0
2.0
2.5
High- Level Output Voltage [V]
3.0
–9
0.0
3.5
GPIO_Px_CTRL DRIVEMODE = LOWEST
3.0
3.5
0
- 40°C
25°C
85°C
- 40°C
25°C
85°C
–10
High- Level Output Current [m A]
–10
High- Level Output Current [m A]
1.5
1.0
2.0
2.5
High- Level Output Voltage [V]
GPIO_Px_CTRL DRIVEMODE = LOW
0
–20
–30
–40
–50
0.0
0.5
–20
–30
–40
0.5
1.5
1.0
2.0
2.5
High- Level Output Voltage [V]
3.0
–50
0.0
3.5
GPIO_Px_CTRL DRIVEMODE = STANDARD
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
0.5
1.5
1.0
2.0
2.5
High- Level Output Voltage [V]
3.0
3.5
GPIO_Px_CTRL DRIVEMODE = HIGH
24
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
3.9 Oscillators
3.9.1 LFXO
Table 3.8. LFXO
Symbol
Parameter
Condition
Min
Typ
Max
fLFXO
Supported nominal
crystal frequency
ESRLFXO
Supported crystal
equivalent series resistance (ESR)
CLFXOL
Supported crystal
external load range
DCLFXO
Duty cycle
ILFXO
Current consumption for core and
buffer after startup.
ESR=30 kOhm, CL=10 pF,
LFXOBOOST in CMU_CTRL is
1
190
nA
tLFXO
Start- up time.
ESR=30 kOhm, CL=10 pF,
40% - 60% duty cycle has
been reached, LFXOBOOST in
CMU_CTRL is 1
400
ms
32.768
Unit
kHz
30
120 kOhm
5
25 pF
48
50
53.5 %
For safe startup of a given crystal, the energyAware Designer in Simplicity Studio contains a tool to help
users configure both load capacitance and software settings for using the LFXO. For details regarding
the crystal configuration, the reader is referred to application note "AN0016 EFM32 Oscillator Design
Consideration".
3.9.2 HFXO
Table 3.9. HFXO
Symbol
Parameter
fHFXO
Supported nominal
crystal Frequency
ESRHFXO
The transconductance of the HFXO
input transistor at
crystal startup
CHFXOL
Supported crystal
external load range
DCHFXO
Duty cycle
tHFXO
Min
Typ
Current consumption for HFXO after
startup
Startup time
Max
4
Supported crystal
Crystal frequency 24 MHz
equivalent series reCrystal frequency 4 MHz
sistance (ESR)
gmHFXO
IHFXO
Condition
HFXOBOOST in CMU_CTRL
equals 0b11
24 MHz
30
60 Ohm
400
1500 Ohm
20
mS
5
46
Unit
25 pF
50
54 %
4 MHz: ESR=400 Ohm,
CL=20 pF, HFXOBOOST in
CMU_CTRL equals 0b11
85
µA
24 MHz: ESR=30 Ohm,
CL=10 pF, HFXOBOOST in
CMU_CTRL equals 0b11
165
µA
24 MHz: ESR=30 Ohm,
CL=10 pF, HFXOBOOST in
CMU_CTRL equals 0b11
400
µs
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
25
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
3.9.3 LFRCO
Table 3.10. LFRCO
Symbol
Parameter
fLFRCO
Oscillation frequency , VDD= 3.0 V,
TAMB=25°C
32.768
tLFRCO
Startup time not including software
calibration
150
µs
ILFRCO
Current consumption
190
nA
TUNESTEPL-
Frequency step
for LSB change in
TUNING value
1.5
%
FRCO
Condition
Min
Typ
Max
Unit
kHz
Figure 3.20. Calibrated LFRCO Frequency vs Temperature and Supply Voltage
42
42
- 40°C
25°C
85°C
40
40
38
Frequency [kHz]
Frequency [kHz]
38
36
34
34
32
32
30
1.8
2.2
2.6
3.0
3.4
30
–40
3.8
Vdd [V]
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
26
1.8 V
3V
3.8 V
36
–15
5
25
Tem perature [°C]
45
65
85
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
3.9.4 HFRCO
Table 3.11. HFRCO
Symbol
Parameter
Condition
Oscillation frequency, VDD= 3.0 V,
TAMB=25°C
fHFRCO
tHFRCO_settling
Settling time after
start-up
Current consumption
IHFRCO
DCHFRCO
Duty cycle
TUNESTEPH-
Frequency step
for LSB change in
TUNING value
FRCO
Min
Typ
Max
Unit
21 MHz frequency band
21
MHz
14 MHz frequency band
14
MHz
11 MHz frequency band
11
MHz
7 MHz frequency band
6.6
MHz
1 MHz frequency band
1.2
MHz
fHFRCO = 14 MHz
0.6
Cycles
fHFRCO = 21 MHz
93
µA
fHFRCO = 14 MHz
77
µA
fHFRCO = 11 MHz
72
µA
fHFRCO = 6.6 MHz
63
µA
fHFRCO = 1.2 MHz
22
µA
fHFRCO = 14 MHz
48.5
50
51 %
0.3
%
Figure 3.21. Calibrated HFRCO 11 MHz Band Frequency vs Supply Voltage and Temperature
11.15
11.20
11.15
11.10
1.8 V
3V
3.8 V
11.10
11.00
10.95
Frequency [MHz]
Frequency [MHz]
11.05
- 40°C
25°C
85°C
11.05
11.00
10.95
10.90
10.90
10.85
10.80
1.8
10.85
2.2
2.6
3.0
3.4
10.80
–40
3.8
Vdd [V]
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
27
–15
5
25
Tem perature [°C]
45
65
85
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Figure 3.22. Calibrated HFRCO 14 MHz Band Frequency vs Supply Voltage and Temperature
14.15
14.15
- 40°C
25°C
85°C
14.10
14.10
14.05
Frequency [MHz]
Frequency [MHz]
14.05
14.00
14.00
13.95
13.95
13.90
13.90
13.85
1.8
1.8 V
3V
3.8 V
2.2
2.6
3.0
3.4
13.85
–40
3.8
–15
5
25
Tem perature [°C]
Vdd [V]
45
65
85
Figure 3.23. Calibrated HFRCO 21 MHz Band Frequency vs Supply Voltage and Temperature
21.2
21.2
- 40°C
25°C
85°C
21.1
21.1
21.0
Frequency [MHz]
Frequency [MHz]
21.0
20.9
20.9
20.8
20.8
20.7
20.7
20.6
1.8
1.8 V
3V
3.8 V
2.2
2.6
3.0
3.4
20.6
–40
3.8
–15
Vdd [V]
5
25
Tem perature [°C]
45
Typ
Max
65
85
3.9.5 ULFRCO
Table 3.12. ULFRCO
Symbol
Parameter
Condition
fULFRCO
Oscillation frequency
25°C, 3V
TCULFRCO
Temperature coefficient
0.05
%/°C
VCULFRCO
Supply voltage coefficient
-18.2
%/V
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
Min
0.8
28
Unit
1.5 kHz
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
3.10 Analog Comparator (ACMP)
Table 3.13. ACMP
Symbol
Parameter
VACMPIN
Input voltage range
0
VDD V
VACMPCM
ACMP Common
Mode voltage range
0
VDD V
IACMP
IACMPREF
VACMPOFFSET
VACMPHYST
RCSRES
tACMPSTART
Active current
Current consumption of internal voltage reference
Condition
Min
Typ
Max
Unit
BIASPROG=0b0000, FULLBIAS=0 and HALFBIAS=1 in
ACMPn_CTRL register
0.1
µA
BIASPROG=0b1111, FULLBIAS=0 and HALFBIAS=0 in
ACMPn_CTRL register
2.87
µA
BIASPROG=0b1111, FULLBIAS=1 and HALFBIAS=0 in
ACMPn_CTRL register
195
µA
Internal voltage reference off.
Using external voltage reference
0
µA
Internal voltage reference
5
µA
Single ended
10
mV
Differential
10
mV
Programmable
17
mV
CSRESSEL=0b00 in
ACMPn_INPUTSEL
39
kOhm
CSRESSEL=0b01 in
ACMPn_INPUTSEL
71
kOhm
CSRESSEL=0b10 in
ACMPn_INPUTSEL
104
kOhm
CSRESSEL=0b11 in
ACMPn_INPUTSEL
136
kOhm
Offset voltage
ACMP hysteresis
Capacitive Sense
Internal Resistance
Startup time
10 µs
The total ACMP current is the sum of the contributions from the ACMP and its internal voltage reference
as given in Equation 3.1 (p. 29) . IACMPREF is zero if an external voltage reference is used.
Total ACMP Active Current
IACMPTOTAL = IACMP + IACMPREF
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
29
(3.1)
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Figure 3.24. ACMP Characteristics, Vdd = 3V, Temp = 25°C, FULLBIAS = 0, HALFBIAS = 1
4.5
2.5
HYSTSEL= 0.0
HYSTSEL= 2.0
HYSTSEL= 4.0
HYSTSEL= 6.0
4.0
3.5
Response Tim e [us]
Current [uA]
2.0
1.5
1.0
3.0
2.5
2.0
1.5
1.0
0.5
0.5
0.0
4
8
ACMP_CTRL_BIASPROG
0
0.0
12
Current consumption, HYSTSEL = 4
0
2
4
6
8
10
ACMP_CTRL_BIASPROG
12
14
Response time
100
BIASPROG= 0.0
BIASPROG= 4.0
BIASPROG= 8.0
BIASPROG= 12.0
Hysteresis [m V]
80
60
40
20
0
0
1
2
4
3
ACMP_CTRL_HYSTSEL
5
6
7
Hysteresis
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
30
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
3.11 Voltage Comparator (VCMP)
Table 3.14. VCMP
Symbol
Parameter
VVCMPIN
Input voltage range
VDD
V
VVCMPCM
VCMP Common
Mode voltage range
VDD
V
BIASPROG=0b0000 and
HALFBIAS=1 in VCMPn_CTRL
register
0.1
µA
BIASPROG=0b1111 and
HALFBIAS=0 in VCMPn_CTRL
register. LPREF=0.
14.7
µA
NORMAL
10
µs
Single ended
10
mV
Differential
10
mV
17
mV
IVCMP
Condition
Min
Typ
Max
Unit
Active current
tVCMPREF
Startup time reference generator
VVCMPOFFSET
Offset voltage
VVCMPHYST
VCMP hysteresis
tVCMPSTART
Startup time
10 µs
The VDD trigger level can be configured by setting the TRIGLEVEL field of the VCMP_CTRL register in
accordance with the following equation:
VCMP Trigger Level as a Function of Level Setting
VDD Trigger Level=1.667V+0.034 ×TRIGLEVEL
(3.2)
3.12 I2C
Table 3.15. I2C Standard-mode (Sm)
Symbol
Parameter
Min
Typ
0
Max
Unit
fSCL
SCL clock frequency
tLOW
SCL clock low time
4.7
µs
tHIGH
SCL clock high time
4.0
µs
tSU,DAT
SDA set-up time
250
ns
tHD,DAT
SDA hold time
tSU,STA
Repeated START condition set-up time
4.7
µs
tHD,STA
(Repeated) START condition hold time
4.0
µs
tSU,STO
STOP condition set-up time
4.0
µs
tBUF
Bus free time between a STOP and START condition
4.7
µs
8
100
1
2,3
3450
kHz
ns
1
For the minimum HFPERCLK frequency required in Standard-mode, see the I2C chapter in the EFM32ZG Reference Manual.
The maximum SDA hold time (tHD,DAT) needs to be met only when the device does not stretch the low time of SCL (tLOW).
3
-9
When transmitting data, this number is guaranteed only when I2Cn_CLKDIV < ((3450*10 [s] * fHFPERCLK [Hz]) - 5).
2
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
31
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Table 3.16. I2C Fast-mode (Fm)
Symbol
Parameter
Min
Typ
Max
fSCL
SCL clock frequency
tLOW
SCL clock low time
1.3
µs
tHIGH
SCL clock high time
0.6
µs
tSU,DAT
SDA set-up time
100
ns
tHD,DAT
SDA hold time
tSU,STA
Repeated START condition set-up time
0.6
µs
tHD,STA
(Repeated) START condition hold time
0.6
µs
tSU,STO
STOP condition set-up time
0.6
µs
tBUF
Bus free time between a STOP and START condition
1.3
µs
0
Unit
1
400
2,3
8
900
kHz
ns
1
For the minimum HFPERCLK frequency required in Fast-mode, see the I2C chapter in the EFM32ZG Reference Manual.
The maximum SDA hold time (tHD,DAT) needs to be met only when the device does not stretch the low time of SCL (tLOW).
3
-9
When transmitting data, this number is guaranteed only when I2Cn_CLKDIV < ((900*10 [s] * fHFPERCLK [Hz]) - 5).
2
Table 3.17. I2C Fast-mode Plus (Fm+)
Symbol
Parameter
Min
Typ
Max
Unit
fSCL
SCL clock frequency
tLOW
SCL clock low time
0.5
µs
tHIGH
SCL clock high time
0.26
µs
tSU,DAT
SDA set-up time
50
ns
tHD,DAT
SDA hold time
8
ns
tSU,STA
Repeated START condition set-up time
0.26
µs
tHD,STA
(Repeated) START condition hold time
0.26
µs
tSU,STO
STOP condition set-up time
0.26
µs
tBUF
Bus free time between a STOP and START condition
0.5
µs
1
0
1000
kHz
1
For the minimum HFPERCLK frequency required in Fast-mode Plus, see the I2C chapter in the EFM32ZG Reference Manual.
3.13 Digital Peripherals
Table 3.18. Digital Peripherals
Symbol
Parameter
Condition
IUSART
USART current
USART idle current, clock enabled
7.5
µA/
MHz
II2C
I2C current
I2C idle current, clock enabled
6.25
µA/
MHz
ITIMER
TIMER current
TIMER_0 idle current, clock
enabled
8.75
µA/
MHz
IPCNT
PCNT current
PCNT idle current, clock enabled
100
nA
IRTC
RTC current
RTC idle current, clock enabled
100
nA
IGPIO
GPIO current
GPIO idle current, clock enabled
5.31
µA/
MHz
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
Min
32
Typ
Max
Unit
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Symbol
Parameter
Condition
IPRS
PRS current
PRS idle current
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
Min
Typ
Max
2,81
33
Unit
µA/
MHz
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
4 Pinout and Package
Note
Please refer to the application note "AN0002 EFM32 Hardware Design Considerations" for
guidelines on designing Printed Circuit Boards (PCB's) for the EFM32ZG108.
4.1 Pinout
The EFM32ZG108 pinout is shown in Figure 4.1 (p. 34) and Table 4.1 (p. 34). Alternate locations
are denoted by "#" followed by the location number (Multiple locations on the same pin are split with "/").
Alternate locations can be configured in the LOCATION bitfield in the *_ROUTE register in the module
in question.
Figure 4.1. EFM32ZG108 Pinout (top view, not to scale)
Table 4.1. Device Pinout
Pin #
QFN24 Pin#
and Name
Pin Name
0
VSS
Pin Alternate Functionality / Description
Analog
Timers
Communication
Other
Ground
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
34
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Pin Alternate Functionality / Description
Pin #
QFN24 Pin#
and Name
Pin Name
Analog
Timers
Communication
Other
1
PA0
TIM0_CC0 #0/1/4
LEU0_RX #4
I2C0_SDA #0
PRS_CH0 #0
GPIO_EM4WU0
2
IOVDD_0
3
PC0
ACMP0_CH0
TIM0_CC1 #4
PCNT0_S0IN #2
US1_TX #0
I2C0_SDA #4
PRS_CH2 #0
4
PC1
ACMP0_CH1
TIM0_CC2 #4
PCNT0_S1IN #2
US1_RX #0
I2C0_SCL #4
PRS_CH3 #0
5
PB7
LFXTAL_P
TIM1_CC0 #3
US1_CLK #0
6
PB8
LFXTAL_N
TIM1_CC1 #3
US1_CS #0
7
RESETn
8
PB11
9
AVDD_2
10
PB13
HFXTAL_P
LEU0_TX #1
11
PB14
HFXTAL_N
LEU0_RX #1
12
AVDD_0
13
PD6
TIM1_CC0 #4
PCNT0_S0IN #3
US1_RX #2/3
I2C0_SDA #1
ACMP0_O #2
14
PD7
TIM1_CC1 #4
PCNT0_S1IN #3
US1_TX #2/3
I2C0_SCL #1
CMU_CLK0 #2
15
VDD_DREG
Power supply for on-chip voltage regulator.
16
DECOUPLE
Decouple output for on-chip voltage regulator. An external capacitance of size CDECOUPLE is required at this pin.
17
PC14
TIM1_CC1 #0
PCNT0_S1IN #0
US1_CS #3
PRS_CH0 #2
18
PC15
TIM1_CC2 #0
US1_CLK #3
PRS_CH1 #2
19
PF0
TIM0_CC0 #5
US1_CLK #2
LEU0_TX #3
I2C0_SDA #5
DBG_SWCLK #0
BOOT_TX
20
PF1
TIM0_CC1 #5
US1_CS #2
LEU0_RX #3
I2C0_SCL #5
DBG_SWDIO #0
GPIO_EM4WU3
BOOT_RX
21
PF2
TIM0_CC2 #5
LEU0_TX #4
GPIO_EM4WU4
22
IOVDD_5
23
PE12
TIM1_CC2 #1
I2C0_SDA #6
CMU_CLK1 #2
24
PE13
I2C0_SCL #6
ACMP0_O #0
GPIO_EM4WU5
Digital IO power supply 0.
Reset input, active low.
To apply an external reset source to this pin, it is required to only drive this pin low during reset, and let the internal pull-up ensure that reset is released.
TIM1_CC2 #3
Analog power supply 2.
Analog power supply 0.
Digital IO power supply 5.
4.2 Alternate Functionality Pinout
A wide selection of alternate functionality is available for multiplexing to various pins. This is shown in
Table 4.2 (p. 36) . The table shows the name of the alternate functionality in the first column, followed
by columns showing the possible LOCATION bitfield settings.
Note
Some functionality, such as analog interfaces, do not have alternate settings or a LOCATION bitfield. In these cases, the pinout is shown in the column corresponding to LOCATION 0.
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
35
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Table 4.2. Alternate functionality overview
Alternate
Functionality
LOCATION
0
1
2
3
4
5
6
Description
ACMP0_CH0
PC0
Analog comparator ACMP0, channel 0.
ACMP0_CH1
PC1
Analog comparator ACMP0, channel 1.
ACMP0_O
PE13
BOOT_RX
PF1
Bootloader RX
BOOT_TX
PF0
Bootloader TX
PD6
Analog comparator ACMP0, digital output.
CMU_CLK0
PD7
Clock Management Unit, clock output number 0.
CMU_CLK1
PE12
Clock Management Unit, clock output number 1.
Debug-interface Serial Wire clock input.
DBG_SWCLK
PF0
DBG_SWDIO
PF1
Note that this function is enabled to pin out of reset, and has
a built-in pull up.
GPIO_EM4WU0
PA0
Pin can be used to wake the system up from EM4
GPIO_EM4WU3
PF1
Pin can be used to wake the system up from EM4
GPIO_EM4WU4
PF2
Pin can be used to wake the system up from EM4
GPIO_EM4WU5
PE13
Pin can be used to wake the system up from EM4
HFXTAL_N
PB14
High Frequency Crystal negative pin. Also used as external
optional clock input pin.
HFXTAL_P
PB13
High Frequency Crystal positive pin.
Note that this function is enabled to pin out of reset, and has
a built-in pull down.
Debug-interface Serial Wire data input / output.
I2C0_SCL
I2C0_SDA
PA0
PD7
PC1
PF1
PE13
I2C0 Serial Clock Line input / output.
PD6
PC0
PF0
PE12
I2C0 Serial Data input / output.
LEU0_RX
PB14
PF1
PA0
LEUART0 Receive input.
LEU0_TX
PB13
PF0
PF2
LEUART0 Transmit output. Also used as receive input in half
duplex communication.
LFXTAL_N
PB8
Low Frequency Crystal (typically 32.768 kHz) negative pin.
Also used as an optional external clock input pin.
LFXTAL_P
PB7
Low Frequency Crystal (typically 32.768 kHz) positive pin.
PCNT0_S0IN
PC0
PD6
Pulse Counter PCNT0 input number 0.
PD7
Pulse Counter PCNT0 input number 1.
PCNT0_S1IN
PC14
PC1
PRS_CH0
PA0
PC14
Peripheral Reflex System PRS, channel 0.
PC15
Peripheral Reflex System PRS, channel 1.
PRS_CH1
PRS_CH2
PC0
Peripheral Reflex System PRS, channel 2.
PRS_CH3
PC1
Peripheral Reflex System PRS, channel 3.
TIM0_CC0
PA0
PA0
PA0
PF0
Timer 0 Capture Compare input / output channel 0.
TIM0_CC1
PC0
PF1
Timer 0 Capture Compare input / output channel 1.
TIM0_CC2
PC1
PF2
Timer 0 Capture Compare input / output channel 2.
TIM1_CC0
TIM1_CC1
PC14
TIM1_CC2
PC15
US1_CLK
PB7
US1_CS
US1_RX
PE12
PB7
PD6
Timer 1 Capture Compare input / output channel 0.
PB8
PD7
Timer 1 Capture Compare input / output channel 1.
PB11
Timer 1 Capture Compare input / output channel 2.
PF0
PC15
USART1 clock input / output.
PB8
PF1
PC14
USART1 chip select input / output.
PC1
PD6
PD6
USART1 Asynchronous Receive.
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
36
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Alternate
LOCATION
Functionality
0
1
2
3
4
5
6
Description
USART1 Synchronous mode Master Input / Slave Output
(MISO).
USART1 Asynchronous Transmit.Also used as receive input
in half duplex communication.
US1_TX
PC0
PD7
PD7
USART1 Synchronous mode Master Output / Slave Input
(MOSI).
4.3 GPIO Pinout Overview
The specific GPIO pins available in EFM32ZG108 is shown in Table 4.3 (p. 37) . Each GPIO port is
organized as 16-bit ports indicated by letters A through F, and the individual pin on this port in indicated
by a number from 15 down to 0.
Table 4.3. GPIO Pinout
Port
Pin
15
Pin
14
Pin
13
Pin
12
Pin
11
Pin
10
Pin
9
Pin
8
Pin
7
Pin
6
Pin
5
Pin
4
Pin
3
Pin
2
Pin
1
Pin
0
Port A
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
PA0
Port B
-
PB14
PB13
-
PB11
-
-
PB8
PB7
-
-
-
-
-
-
-
Port C
PC15
PC14
-
-
-
-
-
-
-
-
-
-
-
-
PC1
PC0
Port D
-
-
-
-
-
-
-
-
PD7
PD6
-
-
-
-
-
-
Port E
-
-
PE13
PE12
-
-
-
-
-
-
-
-
-
-
-
-
Port F
-
-
-
-
-
-
-
-
-
-
-
-
-
PF2
PF1
PF0
4.4 QFN24 Package
Figure 4.2. QFN24 (Preliminary)
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
37
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Note:
1. Dimensioning & tolerancing confirm to ASME Y14.5M-1994.
2. All dimensions are in millimeters. Angles are in degrees.
3. Dimension 'b' applies to metallized terminal and is measured between 0.25 mm and 0.30 mm from
the terminal tip. Dimension L1 represents terminal full back from package edge up to 0.1 mm is
acceptable.
4. Coplanarity applies to the exposed heat slug as well as the terminal.
5. Radius on terminal is optional
Table 4.4. QFN24 (Preliminary) (Dimensions in mm)
Symbol
A
A1
Min
0.80
0.00
Nom
0.85
-
Max
0.90
0.05
A3
b
D
E
0.25
0.203
0.30
REF
5.00 5.00
BSC BSC
0.35
D2
E2
3.50
3.50
3.60
3.60
3.70
3.70
e
0.65
BSC
L
L1
0.35
0.00
0.40
0.46
aaa
bbb
ccc
ddd
eee
0.10
0.10
0.10
0.05
0.08
0.10
The QFN24 Package uses Nickel-Palladium-Gold preplated leadframe.
All EFM32 packages are RoHS compliant and free of Bromine (Br) and Antimony (Sb).
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
38
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
5 PCB Layout and Soldering
5.1 Recommended PCB Layout
Figure 5.1. QFN24 PCB Land Pattern
a
p8
b
p7
p1
p6
e
g
p9
c
p2
p5
p3
p4
f
d
Table 5.1. QFN24 PCB Land Pattern Dimensions (Dimensions in mm)
Symbol
Dim. (mm)
Symbol
Pin number
Symbol
Pin number
a
0.80
P1
1
P8
24
b
0.30
P2
6
P9
25
c
0.65
P3
7
-
-
d
5.00
P4
12
-
-
e
5.00
P5
13
-
-
f
3.60
P6
18
-
-
g
3.60
P7
19
-
-
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
39
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Figure 5.2. QFN24 PCB Solder Mask
a
b
g
e
c
f
d
Table 5.2. QFN24 PCB Solder Mask Dimensions (Dimensions in mm)
Symbol
Dim. (mm)
Symbol
Dim. (mm)
a
0.92
e
5.00
b
0.42
f
3.72
c
0.65
g
3.72
d
5.00
-
-
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
40
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Figure 5.3. QFN24 PCB Stencil Design
a
b
x
y
e
z
c
d
Table 5.3. QFN24 PCB Stencil Design Dimensions (Dimensions in mm)
1.
2.
3.
4.
5.
6.
Symbol
Dim. (mm)
Symbol
Dim. (mm)
a
0.60
e
5.00
b
0.25
x
1.00
c
0.65
y
1.00
d
5.00
z
0.50
The drawings are not to scale.
All dimensions are in millimeters.
All drawings are subject to change without notice.
The PCB Land Pattern drawing is in compliance with IPC-7351B.
Stencil thickness 0.125 mm.
For detailed pin-positioning, see Figure 4.2 (p. 37) .
5.2 Soldering Information
The latest IPC/JEDEC J-STD-020 recommendations for Pb-Free reflow soldering should be followed.
The packages have a Moisture Sensitivity Level rating of 3, please see the latest IPC/JEDEC J-STD-033
standard for MSL description and level 3 bake conditions. Place as many and as small as possible vias
underneath each of the solder patches under the ground pad.
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
41
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
6 Chip Marking, Revision and Errata
6.1 Chip Marking
In the illustration below package fields and position are shown.
Figure 6.1. Example Chip Marking
6.2 Revision
The revision of a chip can be determined from the "Revision" field in Figure 6.1 (p. 42) . If the revision
says "ES" (Engineering Sample), the revision must be read out electronically as specified in the reference
manual.
6.3 Errata
No known errata for EFM32ZG108.
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
42
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
7 Revision History
7.1 Revision 0.60
October 9th, 2013
Added I2C characterization data.
Added IDAC characterization data.
Updated current consumption table and figures in Electrical characteristics section.
Removed Environmental information.
Updated trademark, disclaimer and contact information.
Other minor corrections.
7.2 Revision 0.50
April 22nd, 2013
Updated HFCORE max frequency from 32 MHz to 24 MHz.
Updated pinout.
Other minor corrections.
7.3 Revision 0.40
September 11th, 2012
Updated CPU core from Cortex M0 to Cortex M0+.
Updated the HFRCO 1 MHz band typical value to 1.2 MHz.
Updated the HFRCO 7 MHz band typical value to 6.6 MHz.
Corrected operating voltage from 1.8 V to 1.85 V.
Other minor corrections.
7.4 Revision 0.30
July 16th, 2011
Updated the Electrical Characteristics section.
7.5 Revision 0.20
June 8th, 2011
Corrected all current values in Electrical Characteristics section.
Updated Cortex M0 related items in the memory map.
7.6 Revision 0.10
June 7th, 2011
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
43
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Initial preliminary release.
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
44
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
A Disclaimer and Trademarks
A.1 Disclaimer
Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation
of all peripherals and modules available for system and software implementers using or intending to use
the Silicon Laboratories products. Characterization data, available modules and peripherals, memory
sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and
do vary in different applications. Application examples described herein are for illustrative purposes only.
Silicon Laboratories reserves the right to make changes without further notice and limitation to product
information, specifications, and descriptions herein, and does not give warranties as to the accuracy
or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright
licenses granted hereunder to design or fabricate any integrated circuits. The products must not be
used within any Life Support System without the specific written consent of Silicon Laboratories. A "Life
Support System" is any product or system intended to support or sustain life and/or health, which, if it
fails, can be reasonably expected to result in significant personal injury or death. Silicon Laboratories
products are generally not intended for military applications. Silicon Laboratories products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological
or chemical weapons, or missiles capable of delivering such weapons.
A.2 Trademark Information
Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®,
EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem®, Precision32®, ProSLIC®, SiPHY®, USBXpress® and others are trademarks or registered
trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. All other products
or brand names mentioned herein are trademarks of their respective holders.
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
45
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
B Contact Information
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
Please visit the Silicon Labs Technical Support web page:
http://www.silabs.com/support/pages/contacttechnicalsupport.aspx
and register to submit a technical support request.
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
46
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
Table of Contents
1. Ordering Information .................................................................................................................................. 2
2. System Summary ...................................................................................................................................... 3
2.1. System Introduction ......................................................................................................................... 3
2.2. Configuration Summary .................................................................................................................... 6
2.3. Memory Map ................................................................................................................................. 6
3. Electrical Characteristics ............................................................................................................................. 8
3.1. Test Conditions .............................................................................................................................. 8
3.2. Absolute Maximum Ratings .............................................................................................................. 8
3.3. General Operating Conditions ........................................................................................................... 8
3.4. Current Consumption ....................................................................................................................... 9
3.5. Transition between Energy Modes .................................................................................................... 16
3.6. Power Management ....................................................................................................................... 16
3.7. Flash .......................................................................................................................................... 17
3.8. General Purpose Input Output ......................................................................................................... 18
3.9. Oscillators .................................................................................................................................... 25
3.10. Analog Comparator (ACMP) .......................................................................................................... 29
3.11. Voltage Comparator (VCMP) ......................................................................................................... 31
3.12. I2C ........................................................................................................................................... 31
3.13. Digital Peripherals ....................................................................................................................... 32
4. Pinout and Package ................................................................................................................................. 34
4.1. Pinout ......................................................................................................................................... 34
4.2. Alternate Functionality Pinout .......................................................................................................... 35
4.3. GPIO Pinout Overview ................................................................................................................... 37
4.4. QFN24 Package ........................................................................................................................... 37
5. PCB Layout and Soldering ........................................................................................................................ 39
5.1. Recommended PCB Layout ............................................................................................................ 39
5.2. Soldering Information ..................................................................................................................... 41
6. Chip Marking, Revision and Errata .............................................................................................................. 42
6.1. Chip Marking ................................................................................................................................ 42
6.2. Revision ...................................................................................................................................... 42
6.3. Errata ......................................................................................................................................... 42
7. Revision History ...................................................................................................................................... 43
7.1. Revision 0.60 ............................................................................................................................... 43
7.2. Revision 0.50 ............................................................................................................................... 43
7.3. Revision 0.40 ............................................................................................................................... 43
7.4. Revision 0.30 ............................................................................................................................... 43
7.5. Revision 0.20 ............................................................................................................................... 43
7.6. Revision 0.10 ............................................................................................................................... 43
A. Disclaimer and Trademarks ....................................................................................................................... 45
A.1. Disclaimer ................................................................................................................................... 45
A.2. Trademark Information ................................................................................................................... 45
B. Contact Information ................................................................................................................................. 46
B.1. ................................................................................................................................................. 46
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
47
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
List of Figures
2.1. Block Diagram ....................................................................................................................................... 3
2.2. EFM32ZG108 Memory Map with largest RAM and Flash sizes ........................................................................ 7
3.1. EM0 Current consumption while executing prime number calculation code from flash with HFRCO running at
24MHz ..................................................................................................................................................... 10
3.2. EM0 Current consumption while executing prime number calculation code from flash with HFRCO running at
21MHz ..................................................................................................................................................... 10
3.3. EM0 Current consumption while executing prime number calculation code from flash with HFRCO running at
14MHz ..................................................................................................................................................... 11
3.4. EM0 Current consumption while executing prime number calculation code from flash with HFRCO running at
11MHz ..................................................................................................................................................... 11
3.5. .......................................................................................................................................................... 12
3.6. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 24MHz ............................... 12
3.7. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 21MHz ............................... 13
3.8. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 14MHz ............................... 13
3.9. EM1 Current consumption with all peripheral clocks disabled and HFRCO running at 11MHz ............................... 14
3.10. ........................................................................................................................................................ 14
3.11. EM2 current consumption. RTC prescaled to 1kHz, 32.768 kHz LFRCO. ....................................................... 15
3.12. EM3 current consumption. ................................................................................................................... 15
3.13. EM4 current consumption. ................................................................................................................... 16
3.14. Typical Low-Level Output Current, 2V Supply Voltage ................................................................................ 19
3.15. Typical High-Level Output Current, 2V Supply Voltage ................................................................................ 20
3.16. Typical Low-Level Output Current, 3V Supply Voltage ................................................................................ 21
3.17. Typical High-Level Output Current, 3V Supply Voltage ................................................................................ 22
3.18. Typical Low-Level Output Current, 3.8V Supply Voltage .............................................................................. 23
3.19. Typical High-Level Output Current, 3.8V Supply Voltage ............................................................................. 24
3.20. Calibrated LFRCO Frequency vs Temperature and Supply Voltage .............................................................. 26
3.21. Calibrated HFRCO 11 MHz Band Frequency vs Supply Voltage and Temperature ........................................... 27
3.22. Calibrated HFRCO 14 MHz Band Frequency vs Supply Voltage and Temperature ........................................... 28
3.23. Calibrated HFRCO 21 MHz Band Frequency vs Supply Voltage and Temperature ........................................... 28
3.24. ACMP Characteristics, Vdd = 3V, Temp = 25°C, FULLBIAS = 0, HALFBIAS = 1 ............................................. 30
4.1. EFM32ZG108 Pinout (top view, not to scale) .............................................................................................. 34
4.2. QFN24 (Preliminary) .............................................................................................................................. 37
5.1. QFN24 PCB Land Pattern ...................................................................................................................... 39
5.2. QFN24 PCB Solder Mask ....................................................................................................................... 40
5.3. QFN24 PCB Stencil Design .................................................................................................................... 41
6.1. Example Chip Marking ........................................................................................................................... 42
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
48
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
List of Tables
1.1. Ordering Information ................................................................................................................................ 2
2.1. Configuration Summary ............................................................................................................................ 6
3.1. Absolute Maximum Ratings ...................................................................................................................... 8
3.2. General Operating Conditions ................................................................................................................... 8
3.3. Current Consumption ............................................................................................................................... 9
3.4. Energy Modes Transitions ...................................................................................................................... 16
3.5. Power Management ............................................................................................................................... 17
3.6. Flash .................................................................................................................................................. 17
3.7. GPIO .................................................................................................................................................. 18
3.8. LFXO .................................................................................................................................................. 25
3.9. HFXO ................................................................................................................................................. 25
3.10. LFRCO .............................................................................................................................................. 26
3.11. HFRCO ............................................................................................................................................. 27
3.12. ULFRCO ............................................................................................................................................ 28
3.13. ACMP ............................................................................................................................................... 29
3.14. VCMP ............................................................................................................................................... 31
3.15. I2C Standard-mode (Sm) ...................................................................................................................... 31
3.16. I2C Fast-mode (Fm) ............................................................................................................................ 32
3.17. I2C Fast-mode Plus (Fm+) .................................................................................................................... 32
3.18. Digital Peripherals ............................................................................................................................... 32
4.1. Device Pinout ....................................................................................................................................... 34
4.2. Alternate functionality overview ................................................................................................................ 36
4.3. GPIO Pinout ........................................................................................................................................ 37
4.4. QFN24 (Preliminary) (Dimensions in mm) .................................................................................................. 38
5.1. QFN24 PCB Land Pattern Dimensions (Dimensions in mm) .......................................................................... 39
5.2. QFN24 PCB Solder Mask Dimensions (Dimensions in mm) ........................................................................... 40
5.3. QFN24 PCB Stencil Design Dimensions (Dimensions in mm) ........................................................................ 41
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
49
www.silabs.com
Preliminary
...the world's most energy friendly microcontrollers
List of Equations
3.1. Total ACMP Active Current ..................................................................................................................... 29
3.2. VCMP Trigger Level as a Function of Level Setting ..................................................................................... 31
2013-10-09 - EFM32ZG108FXX - d0063_Rev0.60
50
www.silabs.com