SLPOWER MW153KB18XX

MW153KB
Universal 25-40 Watt Series
• 100-240 VAC Universal Input
• Desktop Style
• Single Output to 40W
• Four Models Available; 12V to 24V
• Regulated Output with Low Ripple
• Impact Resistant Polycarbonate Enclosure
• Modified and Custom Designs Also Available
•Designed to Meet EISA Requirements —
see reverse side for details
International Safety Standard Approvals
Specifications
General Specifications
Line and Load Regulation (Excluding cord)
Line Voltage +/-1% Load Voltage +/-5%
Topology
Switching-Fixed Frequency Flyback
Ripple
1% Vp-p max.
Efficiency Transient Response
0.5ms for 50% Load change Typical
esigned to Meet EISA D
Requirements — see reverse side
Protection Over-current Protection
(Hiccup) Short Circuit Protection
Hold-up Time @115VAC
18ms min.
Dielectric Withstand
Input Specifications
,000VAC or 5,656VDC 4
Primary - Secondary;
1,500VAC or 2,150VDC Primary-F.G; 500VDC Secondary-F.G
Input Voltage Range Universal input 100-240VAC -10%, +10%
Storage Temp -30° C to 85° C
Line Frequency 47-63Hz
Input Current 90VAC Input
0.4A max. Protection
Internal Primary Current Fuse,
Inrush Limiting
Approvals and Safety Standards UL60601-1
IEC/EN60601-1 EMC : EN60601-1-2/EN55024
Environmental Specifications
Thermal Performance Operating temperature full load, no derating convectional cooling Non vented case
Relative Humidity Non-condensing
5% to 95% Altitude 0-10,000 feet
Output Specifications
0° C to 40° C MTBF
100,000 Calculated Hours
Case and Dimension Desktop style
3.98L x 2.4W x 1.34H (in)
101L x 61W x 34H (mm)
Case Material Black 94V0
Polycarbonate
Cord and Connectors 8 AWG 1,500mm 1
2 Conductor. Ault #3
Connector. Other connectors
are also available.
SL Power Electronics Corp • 6050 King Drive • Ventura, CA 93003 • Phone:805.486.4565 • Fax:858.712.2040 • Email:[email protected] • www.slpower.com
rica/
MW153KB
Universal 25-40 Watt Series
For the most current data and application support visit www.slpower.com
Output Current
Output
Voltage Max
Ault Part Number
Max
Watts
Ripple
Vp-p max.
MW153KB12XX
12 V 3.40 A 40.8 W
120 mV
MW153KB15XX
15 V 2.70 A 40.5 W
150 mV
MW153KB18XX
18 V 2.20 A
39.6 W
180 mV
MW153KB24XX
24 V 1.70 A 40.8 W
240 mV
Ault Part Number Key
MW153
K
B
12
XX
Pin Connections
Product Family Name
Manufacturing Location
Design Revision
Changes
Voltage
DC
Connector
Number
Input Configuration
IEC320
United
w/ground
Kingdom
C14(G)
(F)
Specify the Input Configuration Code in your order.
Europe
(M)
IEC320
Australian
w/o
(E) ground
C18
(Q)
N.
America/
Shaver
Japan
C8
(B)
(N)
Europe
(M)
United
Kingdom
(G)
Australian
(E)
Shaver
C8
(N)
Pinout Code
Center contact: positive
Description
Switchcraft 760 plug or equivalent
Suggested Mating Switchcraft 712A jack or equivalent
Other Connectors are available by special order
2007 Energy Independence and Security Act – EISA
The Energy Independence and Security Act of 2007 was passed in December
of 2007 and addresses minimum efficiency standards and standby levels
for Class A external power supplies that are 250 watts and under. This law
stipulates that external power supplies manufactured on July 1, 2008 and
beyond meet certain minimum efficiency and standby criteria as defined
below.
Minimum Efficiency Criteria
ctive mode is defined as when a power supply’s input is connected to line
A
voltage AC and its output is connected to a DC or AC load drawing a portion
of the product’s power output. Depending on the power rating for the power
supply, it must meet the minimum efficiency criteria outlined below.
Energy-Efficiency Criteria for Active Mode: output power on minimum average
adapter label efficiency percentage ≥ 0.50 * output power on adapter label 0 to ≤ less than 1 watt ≥ [0.09 * Ln (output power on adapter > 1 to ≤ 51 watts label )] + 0.50 ≥ 0.85
> 51 watts he power supply must also meet a requirement for when its input is
T
connected to a line voltage AC but its output is not connected to a load. Depending on the power output of the supply, it must keep its energy
consumption below the following values.
Energy Consumption Criteria for No Load Mode:
output power on maximum power consumption adapter label
in no-load mode ≤ 0.5 watts
0 to < 250 watts SL Power Electronics Corp • 6050 King Drive • Ventura, CA 93003 • Phone:805.486.4565 • Fax:858.712.2040 • Email:[email protected] • www.slpower.com
Data Sheet © 2008 SL Power Electronics Corp. The information and specifications contained in this data sheet are believed to be correct at time of publication. However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice.
Rev.6/9/08