Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2012. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. ■ Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is available. ■ Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. ■ All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. ■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called“TAIYO YUDEN’ s official sales channel”). It is only applicable to the products purchased from any of TAIYO YUDEN’s official sales channel. ■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights. ■ Caution for export Certain items in this catalog may require specific procedures for export according to“Foreign Exchange and Foreign Trade Control Law”of Japan,“U.S. Export Administration Regulations”, and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff. 13 MULTILAYER EMI SUPPRESSION FILTERS REFLOW ■ FEATURES ■ APPLICATIONS ◦2×1.25mm size EMI filter unifying multilayer capacitor and inductor T series with rapid attenuation characteristics and TZ series with effective maintaining of waveform quality of digital signal are lined up. ◦Noise countermeasure in visual signal such as DVD, DSC, PDP, etc. (T series) ◦Noise countermeasure and maintaining waveform quality in digital signal processing circuit in personal computer, communication equipment, etc. (TZ series) ◦Same shape as multilayer capacitor which is suitable for high speed mounting by automatic machine. ■ OPERATING TEMPERATURE RANGE ◦－25～＋85℃ ■ ORDERING CODE 【T Series】 ／ MULTILAYER EMI SUPPRESSION FILTERS NOISE SUPPRESSION COMPONENTS F K 2 1 ❶ FK 2 5 T ❷ ❶Type Multilayer EMI Suppression Filter 2 ❸ ❸Equivalence circuit T T type 5 6 ❹ L ー T ○ ❺ ❻ ❼ ❻Rated Voltage［V］ L 10 ❹Cutoff frequency example 186 256 A ーT ❽ ❼Packaging Tape & Reel △ ❽Internal Code Standard products △=Blank space 18 MHz 25 MHz ❷External dimensions (L×W)［mm］ 2125（0805） 2.0×1.25 ❺Characteristic example Sharp A 【TZ Series】 F K 2 ❶ FK ❶Type Multilayer EMI Suppression Filter 1 2 5 T ❷ Z ❸ 2 0 1 C 8 5 ❹ ❸Equivalence circuit T T type ❺ ❹Nominal Impedance ［100MHz］ Z700 70Ω Z101 100Ω Z201 200Ω ❷External dimensions (L×W)［mm］ 2125（0805） 2.0×1.25 T ○ 0 ❺Nominal Capacitance ［1MHz］ C170 17pF C500 50pF C850 85pF T ❻ ❻Packaging Tape & Reel △ ❼ ❼Internal Code Standard products △=Blank space ■ EXTERNAL DIMENSIONS/STANDARD QUANTITY L W T e1 e2 Standard Quantity [pcs] Embossed tape 2.0±0.2 (0.079±0.008) 1.25±0.2 (0.049±0.008) 1.0±0.2 (0.039±0.008) 0.3±0.2 (0.012±0.008) 0.4±0.2 (0.016±0.008) 3000 Unit : mm (inch) ■ PART NUMBERS ●T Series Ordering code EHS (Environmental Hazardous Substances) Cut-Off Frequency FK2125T186AL FK2125T256AL FK2125T406AL FK2125T107AL FK2125T167AL FK2125T207AL FK2125T407AL RoHS RoHS RoHS RoHS RoHS RoHS RoHS 18MHz±3.6MHz 25MHz±5MHz 40MHz±10MHz 100MHz±20MHz 160MHz±30MHz 200MHz±40MHz 400MHz±80MHz Characteristic DC Rated Rated Insulation attnuation resistance insertion-loss Voltage current resistance max. [1MHz] ［50MHz］ ［100MHz］［200MHz］［350MHz］［500MHz］［600MHz］［800MHz］ ≧20dB ≧20dB ー ー ≧20dB ー ー ≧15dB ≧20dB ー ー ≧20dB ー ー 2Ω ー ≧15dB ≧20dB ー ≧20dB ー ー 100mA ≦1.0dB ー ー ≧20dB ー ≧20dB ー ー 3Ω 10V DC ≧30MΩ DC ー ー ー ≧20dB ≧20dB ー ー ー ー ー ≧20dB ≧20dB ー ー 2Ω ー ー ー ー ー ≧20dB ≧20dB ●TZ Series Ordering code FK2125TZ700C170 FK2125TZ700C500 FK2125TZ700C850 FK2125TZ101C170 FK2125TZ101C500 FK2125TZ101C850 FK2125TZ201C850 EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS impedance (terminal1-3) ［100MHz］ 70Ω±30% 70Ω±30% 70Ω±30% 100Ω±30% 100Ω±30% 100Ω±30% 200Ω±30% capacitance (terminal1-2) ［1MHz］ 17pF±20% 50pF±20% 85pF±20% 17pF±20% 50pF±20% 85pF±20% 85pF±20% DC resistance max. Rated Voltage Rated current Insulation resistance 2Ω 10V DC 100mA DC ≧30MΩ ▶This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 112 13 MULTILAYER EMI SUPPRESSION FILTERS ■PACKAGING ①Minimum Quantity ●Taped package Type FK 2125（0805） Thickness mm（inch） 1.0（0.039） Standard Quantity [pcs] Embossed tape 3000 ②Tape material ●Embossed Tape ③Taping dimensions ●Embossed tape 8mm wide (0.031 inches wide) Type FK 2125（0805） Chip cavity A B 1.5±0.2 2.3±0.2 （0.059±0.008） （0.091±0.008） Insertion pitch F 4.0±0.1 （0.157±0.004） Tape thickness K T 2.0 max. 0.3 max. （0.079 max.） （0.012 max.） Unit : mm（inch） ④Leader and Blank portion ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . emifilter_pack_e-01 ⑤Reel size Unit : mm（inch） ⑥Top tape strength The top tape requires a peel;-off force of 0.1～0.7N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . emifilter_pack_e-01 MULTILAYER EMI SUPPRESSION FILTERS ■RELIABILITY DATA 1. Operating Temperature Range Specified Value －25～＋85℃ 2. Storage Temperature Range Specified Value －25～＋85℃ 3. Rated Voltage Specified Value 10V DC 4. Rated Current Specified Value 100mA DC 5. Cutoff frequency (T Series) Specified Value 18MHz±3.6MHz, 25MHz±5MHz, 40MHz±10MHz, 100MHz±20MHz, 160MHz±30MHz, 200MHz±40MHz, 400MHz±80MHz Test Methods and Remarks Measuring equipment Measuring source Input-Output impedance : 8753D (or its equivalent) : 0dBm : 50Ω 6. Impedance (TZ Series) Specified Value 70Ω±30％, 100Ω±30％, 200Ω±30％ Test Methods and Remarks Measuring Measuring Measuring Measuring frequency equipment jig source : : : : 100MHz 4291A (or its equivalent) 16192A －20dBm 7. Capacitance (TZ Series) Specified Value 17pF±20％, 50pF±20％, 85pF±20％ Test Methods and Remarks Measuring equipment : 4194A (or its equivalent) Measuring voltage : 0.5V Measuring frequency : 1MHz Capacitance measurement between Terminals 1 and 2. 8. DC Resistance Specified Value 2Ω max., 3Ω max. (FK2125T107AL) Test Methods and Remarks Conduct measurement between Terminals 1 and 3. 9. Insulation Resistance Specified Value 30MΩ min. Test Methods and Remarks Conduct measurement between Terminals 1 and 2. Applied voltage : 10VDC 10. Resistance to Flexure of Substrate Specified Value No mechanical damage. Warp : 2mm Testing board : glass epoxy-resin substrate Thickness : 0.8mm Test Methods and Remarks ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . emifilter_reli_e-01 11. Solderability Specified Value At least 75% of terminal electrode is covered by new solder. Test Methods and Remarks Solder temperature Duration Preheating temperature Preheating time Flux : : : : : 230±5℃ 4±1 sec. 150 to 180℃ 2 to 3 min. Immersion into methanol solution with colophony for 3 to 5 sec. 12. Resistance to Soldering Specified Value No significant abnormality in appearance. Test Methods and Remarks Solder temperature Duration Preheating temperature Preheating time Flux : : : : : 260±5℃ 10±0.5 sec. 150 to 180℃ 2 to 3 min. Immersion into methanol solution with colophony for 3 to 5 sec. 13. Thermal Shock Specified Value Test Methods and Remarks No mechanical damage. Insulation resistance (between 1 and 2) DC resistance (between 1 and 3) : 20MΩ min. : 2Ω max. : 3Ω max. (FK2125T107AL) Conditions for 1 cycle Step Temperature (℃) 1 Minimum operating temperature ＋0/－3 2 Room temperature 3 Maximum operating temperature ＋3/－0 4 Room temperature Number of cycles Recovery Duration (min) 30±3 2 to 3 30±3 2 to 3 :5 : 2 to 3 hrs of recovery under the standard condition after the test. 14. Damp Heat steady state Specified Value Test Methods and Remarks No mechanical damage. Insulation resistance (between 1 and 2) DC resistance (between 1 and 3) Temperature Humidity Duration Recovery : : : : : 20MΩ min. : 2Ω max. : 3Ω max. (FK2125T107AL) 40±2℃ 90 to 95％RH 500±12 hrs 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. 15. Loading under Damp Heat Specified Value Test Methods and Remarks No mechanical damage. Insulation resistance (between 1 and 2) DC resistance (between 1 and 3) Temperature Humidity Applied voltage Applied current Duration Recovery : 20MΩ min. : 2Ω max. : 3Ω max. (FK2125T107AL) : 40±2℃ : 90 to 95％RH : Rated voltage (between 1 and 2) : Rated current (between 1 and 3) : 500±12 hrs : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. 16. Loading at High Temperature Specified Value Test Methods and Remarks No mechanical damage. Insulation resistance (between 1 and 2) DC resistance (between 1 and 3) Temperature Applied voltage Applied current Duration Recovery : 20MΩ min. : 2Ω max. : 3Ω max. (FK2125T107AL) : 85±2℃ : Rated voltage (between 1 and 2) : Rated current (between 1 and 3) : 500±12 hrs : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . emifilter_reli_e-01 Note on standard condition : "standard condition" referred to herein is defined as follows : 5 to 35℃ of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure. When there are questions concerning measurement results： In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative humidity and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition." ※Circuit diagram ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . emifilter_reli_e-01