MC78L00A Series, NCV78L00A 100 mA Positive Voltage Regulators The MC78L00A Series of positive voltage regulators are inexpensive, easy−to−use devices suitable for a multitude of applications that require a regulated supply of up to 100 mA. Like their higher powered MC7800 and MC78M00 Series cousins, these regulators feature internal current limiting and thermal shutdown making them remarkably rugged. No external components are required with the MC78L00 devices in many applications. These devices offer a substantial performance advantage over the traditional zener diode−resistor combination, as output impedance and quiescent current are substantially reduced. http://onsemi.com 1 Features • • • • • • • • Wide Range of Available, Fixed Output Voltages Low Cost Internal Short Circuit Current Limiting Internal Thermal Overload Protection No External Components Required Complementary Negative Regulators Offered (MC79L00A Series) Pb−Free Packages are Available NCV Prefix for Automotive and Other Applications Requiring Site and Control Changes Q3 15k Input Q11 Q5 Q12 Q1 Q10 5.0k 3.8k Q4 1.9k 1.2k Q6 Output 0−25k 19k 2.2k Q9 C Q8 Q2 Z1 3.0 TO−92 P SUFFIX CASE 029 2 3 Pin: 1. Output 2. Ground 3. Input 8 1 SOIC−8* D SUFFIX CASE 751 *SOIC−8 is an internally modified SO−8 package. Pins 2, 3, 6, and 7 are electrically common to the die attach flag. This internal lead frame modification decreases package thermal resistance and increases power dissipation capability when appropriately mounted on a printed circuit board. SOIC−8 conforms to all external dimensions of the standard SO−8 package. PIN CONNECTIONS VOUT 1 8 VIN GND 2 7 GND GND 3 6 GND NC 4 5 NC 2.85k (Top View) Q7 420 1.0k Ground Figure 1. Representative Schematic Diagram Input MC78LXXA Cin* 0.33F ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet. DEVICE MARKING INFORMATION Output See general marking information in the device marking section on page 13 of this data sheet. CO** Figure 2. Standard Application A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0 V above the output voltage even during the low point on the input ripple voltage. * Cin is required if regulator is located an appreciable distance from power supply filter. ** CO is not needed for stability; however, it does improve transient response. Semiconductor Components Industries, LLC, 2004 December, 2004 − Rev. 9 1 Publication Order Number: MC78L00A/D MC78L00A Series, NCV78L00A MAXIMUM RATINGS (TA = +125°C, unless otherwise noted.) Rating Symbol Value Unit VI 30 35 40 Vdc Storage Temperature Range Tstg −65 to +150 °C Operating Junction Temperature Range TJ 0 to +150 °C Input Voltage (2.6 V−8.0 V) Input Voltage (12 V−18 V) Input Voltage (24 V) Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. ELECTRICAL CHARACTERISTICS (VI = 10 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, − 40°C < TJ < +125°C (for MC78LXXAB, NCV78L05A), 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.) MC78L05AC, AB, NCV78L05A Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) Characteristics VO 4.8 5.0 5.2 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 7.0 Vdc ≤ VI ≤ 20 Vdc 8.0 Vdc ≤ VI ≤ 20 Vdc Regline Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (7.0 Vdc ≤ VI ≤ 20 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (VI = 10 V, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB mV − − 55 45 150 100 − − 11 5.0 60 30 4.75 4.75 − − 5.25 5.25 − − 3.8 − 6.0 5.5 − − − − 1.5 0.1 mV Vdc mA IIB Input Bias Current Change (8.0 Vdc ≤ VI ≤ 20 Vdc) (1.0 mA ≤ IO ≤ 40 mA) mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 40 − V Ripple Rejection (IO = 40 mA, f = 120 Hz, 8.0 Vdc ≤ VI ≤ 18 V, TJ = +25°C) RR 41 49 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) NOTE: NCV78L05A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. http://onsemi.com 2 MC78L00A Series, NCV78L00A ELECTRICAL CHARACTERISTICS (VI = 14 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, − 40°C < TJ < +125°C (for MC78LXXAB), 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.) MC78L08AC, AB Characteristics Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) VO 7.7 8.0 8.3 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 10.5 Vdc ≤ VI ≤ 23 Vdc 11 Vdc ≤ VI ≤ 23 Vdc Regline Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (10.5 Vdc ≤ VI ≤ 23 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (VI = 14 V, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB mV − − 20 12 175 125 − − 15 8.0 80 40 7.6 7.6 − − 8.4 8.4 − − 3.0 − 6.0 5.5 − − − − 1.5 0.1 mV Vdc mA IIB Input Bias Current Change (11 Vdc ≤ VI ≤ 23 Vdc) (1.0 mA ≤ IO ≤ 40 mA) mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 60 − V Ripple Rejection (IO = 40 mA, f = 120 Hz, 12 V ≤ VI ≤ 23 V, TJ = +25°C) RR 37 57 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) ELECTRICAL CHARACTERISTICS (VI = 15 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, − 40°C < TJ < +125°C (for MC78LXXAB), 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.) MC78L09AC, AB Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) Characteristics VO 8.6 9.0 9.4 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 11.5 Vdc ≤ VI ≤ 24 Vdc 12 Vdc ≤ VI ≤ 24 Vdc Regline Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (11.5 Vdc ≤ VI ≤ 24 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (VI = 15 V, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB mV − − 20 12 175 125 − − 15 8.0 90 40 8.5 8.5 − − 9.5 9.5 − − 3.0 − 6.0 5.5 − − − − 1.5 0.1 mV Vdc mA IIB Input Bias Current Change (11 Vdc ≤ VI ≤ 23 Vdc) (1.0 mA ≤ IO ≤ 40 mA) mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 60 − V Ripple Rejection (IO = 40 mA, f = 120 Hz, 13 V ≤ VI ≤ 24 V, TJ = +25°C) RR 37 57 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) http://onsemi.com 3 MC78L00A Series, NCV78L00A ELECTRICAL CHARACTERISTICS (VI = 19 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, − 40°C < TJ < +125°C (for MC78LXXAB), 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.) MC78L12AC, AB Characteristics Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) VO 11.5 12 12.5 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 14.5 Vdc ≤ VI ≤ 27 Vdc 16 Vdc ≤ VI ≤ 27 Vdc Regline Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (14.5 Vdc ≤ VI ≤ 27 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (VI = 19 V, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB mV − − 120 100 250 200 − − 20 10 100 50 11.4 11.4 − − 12.6 12.6 − − 4.2 − 6.5 6.0 − − − − 1.5 0.1 mV Vdc mA IIB Input Bias Current Change (16 Vdc ≤ VI ≤ 27 Vdc) (1.0 mA ≤ IO ≤ 40 mA) mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 80 − V Ripple Rejection (IO = 40 mA, f = 120 Hz, 15 V ≤ VI ≤ 25 V, TJ = +25°C) RR 37 42 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) ELECTRICAL CHARACTERISTICS (VI = 23 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, − 40°C < TJ < +125°C (for MC78LXXAB), S 0°C < TJ < +125°C (for MC78LXXAC), unless otherwise noted.) MC78L15AC, AB Characteristics Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) VO 14.4 15 15.6 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 17.5 Vdc ≤ VI ≤ 30 Vdc 20 Vdc ≤ VI ≤ 30 Vdc Regline Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (17.5 Vdc ≤ VI ≤ 30 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (VI = 23 V, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB mV − − 130 110 300 250 − − 25 12 150 75 14.25 14.25 − − 15.75 15.75 − − 4.4 − 6.5 6.0 − − − − 1.5 0.1 mV Vdc mA IIB Input Bias Current Change (20 Vdc ≤ VI ≤ 30 Vdc) (1.0 mA ≤ IO ≤ 40 mA) mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 90 − V Ripple Rejection (IO = 40 mA, f = 120 Hz, 18.5 V ≤ VI ≤ 28.5 V, TJ = +25°C) RR 34 39 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) http://onsemi.com 4 MC78L00A Series, NCV78L00A ELECTRICAL CHARACTERISTICS (VI = 27 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, 0°C < TJ < +125°C, unless otherwise noted.) MC78L18AC Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) Characteristics VO 17.3 18 18.7 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 21.4 Vdc ≤ VI ≤ 33 Vdc 20.7 Vdc ≤ VI ≤ 33 Vdc 22 Vdc ≤ VI ≤ 33 Vdc 21 Vdc ≤ VI ≤ 33 Vdc Regline − 45 325 − 35 275 − − 30 15 170 85 Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (21.4 Vdc ≤ VI ≤ 33 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (20.7 Vdc ≤ VI ≤ 33 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (VI = 27 V, 1.0 mA ≤ IO ≤ 70 mA) (VI = 27 V, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB mV Vdc 17.1 − 18.9 17.1 − 18.9 − − 3.1 − 6.5 6.0 mA IIB Input Bias Current Change (22 Vdc ≤ VI ≤ 33 Vdc) (21 Vdc ≤ VI ≤ 33 Vdc) (1.0 mA ≤ IO ≤ 40 mA) mV mA − − − − 1.5 0.1 Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 150 − V Ripple Rejection (IO = 40 mA, f = 120 Hz, 23 V ≤ VI ≤ 33 V, TJ = +25°C) RR 33 48 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) http://onsemi.com 5 MC78L00A Series, NCV78L00A ELECTRICAL CHARACTERISTICS (VI = 33 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, 0°C < TJ < +125°C, unless otherwise noted.) MC78L24AC Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) Characteristics VO 23 24 25 Vdc Line Regulation (TJ = +25°C, IO = 40 mA) 27.5 Vdc ≤ VI ≤ 38 Vdc 28 Vdc ≤ VI ≤ 80 Vdc 27 Vdc ≤ VI ≤ 38 Vdc Regline Load Regulation (TJ = +25°C, 1.0 mA ≤ IO ≤ 100 mA) (TJ = +25°C, 1.0 mA ≤ IO ≤ 40 mA) Regload Output Voltage (28 Vdc ≤ VI ≤ 38 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (27 Vdc ≤ VI ≤ 38 Vdc, 1.0 mA ≤ IO ≤ 40 mA) (28 Vdc ≤ VI = 33 Vdc, 1.0 mA ≤ IO ≤ 70 mA) (27 Vdc ≤ VI ≤ 33 Vdc, 1.0 mA ≤ IO ≤ 70 mA) VO Input Bias Current (TJ = +25°C) (TJ = +125°C) IIB mV − − − − 50 60 − 300 350 − − 40 20 200 100 mV Vdc 22.8 − 25.2 22.8 − 25.2 − − 3.1 − 6.5 6.0 − − − − 1.5 0.1 mA IIB Input Bias Current Change (28 Vdc ≤ VI ≤ 38 Vdc) (1.0 mA ≤ IO ≤ 40 mA) mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 200 − V Ripple Rejection (IO = 40 mA, f = 120 Hz, 29 V ≤ VI ≤ 35 V, TJ = +25°C) RR 31 45 − dB VI − VO − 1.7 − Vdc Dropout Voltage (TJ = +25°C) http://onsemi.com 6 V I −V O , INPUT/OUTPUT DIFFERENTIAL VOLTAGE (V) MC78L00A Series, NCV78L00A MC78L05AC Vout = 5.0 V TJ = 25°C 6.0 IO = 1.0 mA 4.0 IO = 40 mA IO = 100 mA 2.0 0 0 2.0 4.0 6.0 VI, INPUT VOLTAGE (V) 8.0 10 Figure 3. Dropout Characteristics IO = 70 mA 2.0 1.5 IO = 40 mA 1.0 IO = 1.0 mA Dropout of Regulation is defined as when VO = 2% of VO 0.5 0 0 25 4.0 3.8 3.6 3.4 3.2 MC78L05AC VI = 10 V VO= 5.0 V IO = 40 mA 3.0 125 Figure 4. Dropout Voltage versus Junction Temperature 4.0 MC78L05AC Vout = 5.0 V IO = 40 mA TJ = 25°C 3.0 2.0 1.0 0 0 0 25 50 75 100 TA, AMBIENT TEMPERATURE (°C) 125 0 5.0 10 15 20 25 VI, INPUT VOLTAGE (V) 35 170 10,000 No Heatsink ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ 110 100 RJA = 200°C/W PD(max) to 25°C = 625 mW 75 100 125 TA, AMBIENT TEMPERATURE (°C) 150 Figure 7. Maximum Average Power Dissipation versus Ambient Temperature − TO−92 Type Package Graph represents symmetrical layout 90 L 70 2.0 oz. Copper L 2.4 2.0 1.6 1.2 3.0 mm 50 0.8 RJA 30 0 10 20 30 40 0.4 50 L, LENGTH OF COPPER (mm) Figure 8. SOIC−8 Thermal Resistance and Maximum Power Dissipation versus P.C.B. Copper Length http://onsemi.com 7 2.8 PD(max) for TA = 50°C 130 1000 50 40 3.2 150 10 25 30 Figure 6. Input Bias Current versus Input Voltage R θ JA, THERMAL RESISTANCE JUNCTION-TO-AIR (° C/W) Figure 5. Input Bias Current versus Ambient Temperature PD , POWER DISSIPATION (mW) 50 75 100 TJ, JUNCTION TEMPERATURE (°C) 5.0 I IB , INPUT BIAS CURRENT (mA) I IB , INPUT BIAS CURRENT (mA) 4.2 2.5 PD, MAXIMUM POWER DISSIPATION (W) VO, OUTPUT VOLTAGE (V) 8.0 MC78L00A Series, NCV78L00A APPLICATIONS INFORMATION Design Considerations input bypass capacitor should be selected to provide good high−frequency characteristics to insure stable operation under all load conditions. A 0.33 F or larger tantalum, mylar, or other capacitor having low internal impedance at high frequencies should be chosen. The bypass capacitor should be mounted with the shortest possible leads directly across the regulators input terminals. Good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. Bypassing the output is also recommended. The MC78L00A Series of fixed voltage regulators are designed with Thermal Overload Protection that shuts down the circuit when subjected to an excessive power overload condition. Internal Short Circuit Protection limits the maximum current the circuit will pass. In many low current applications, compensation capacitors are not required. However, it is recommended that the regulator input be bypassed with a capacitor if the regulator is connected to the power supply filter with long wire lengths, or if the output load capacitance is large. The MC78L15A +20V 0.33F Input R IO 6 Constant Current to Grounded Load 2 − MC1741 3 + 4 0.33F 6.5 20V The MC78L00 regulators can also be used as a current source when connected as above. In order to minimize dissipation the MC78L05C is chosen in this application. Resistor R determines the current as follows: 5.0 V IO = + IB R 10k 7 MC78L05A 0.33F +VO 10k MPS A70 −VO MPS U55 Figure 10. ± 15 V Tracking Voltage Regulator +VI MC78LXXA 0.33F IIB = 3.8 mA over line and load changes −VI For example, a 100 mA current source would require R to be a 50, 1/2 W resistor and the output voltage compliance would be the input voltage less 7 V. 0.33F +VO 0.1F MC79LXXA 0.1F −VO Figure 9. Current Regulator Figure 11. Positive and Negative Regulator http://onsemi.com 8 MC78L00A Series, NCV78L00A ORDERING INFORMATION Operating Temperature Range Package Shipping† MC78L05ABD SOIC−8 98 Units/Rail MC78L05ABDG SOIC−8 98 Units/Rail MC78L05ABDR2 Device Output Voltage SOIC−8 2500 Tape & Reel MC78L05ABDR2G SOIC−8 (Pb−Free) 2500 Tape & Reel NCV78L05ABDR2* SOIC−8 2500 Tape & Reel MC78L05ABP TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack SOIC−8 98 Units/Rail SOIC−8 (Pb−Free) 98 Units/Rail SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack MC78L05ABPG TJ = −40° to +125°C MC78L05ABPRA MC78L05ABPRAG MC78L05ABPRE MC78L05ABPREG MC78L05ABPRM MC78L05ABPRMG MC78L05ACD MC78L05ACDG 5.0 V MC78L05ACDR2 MC78L05ACDR2G MC78L05ACP MC78L05ACPG MC78L05ACPRA MC78L05ACPRAG TJ = 0° to +125°C MC78L05ACPRE MC78L05ACPREG MC78L05ACPRM MC78L05ACPRMG MC78L05ACPRP MC78L05ACPRPG *NCV78L05A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 9 MC78L00A Series, NCV78L00A ORDERING INFORMATION Operating Temperature Range Package Shipping† SOIC−8 98 Units/Rail MC78L08ABDG SOIC−8 (Pb−Free) 98 Units/Rail MC78L08ABDR2 SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel Device Output Voltage MC78L08ABD MC78L08ABDR2G TJ = −40° to +125°C MC78L08ABP TO−92 2000 Units/Bag MC78L08ABPRA TO−92 2000 Tape & Reel MC78L08ABPRP TO−92 2000 Ammo Pack MC78L08ACD SOIC−8 98 Units/Rail SOIC−8 98 Units/Rail MC78L08ACDR2 SOIC−8 2500 Tape & Reel MC78L08ACP TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel MC78L08ACPRE TO−92 2000 Tape & Reel MC78L08ACPRP TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack SOIC−8 98 Units/Rail SOIC−8 (Pb−Free) 98 Units/Rail SOIC−8 2500 Tape & Reel MC78L08ACDG 8.0 V MC78L08ACPG TJ = 0° to +125°C MC78L08ACPRA MC78L08ACPRAG MC78L08ACPRPG MC78L09ABD MC78L09ABDG MC78L09ABDR2 TJ = −40° 40° to +125°C MC78L09ABPRA TO−92 2000 Tape & Reel MC78L09ABPRP TO−92 2000 Ammo Pack MC78L09ABDG SOIC−8 (Pb−Free) 98 Units/Rail SOIC−8 98 Units/Rail SOIC−8 (Pb−Free) 98 Units/Rail SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel TO−92 2000 Units/Bag MC78L09ACPG TO−92 (Pb−Free) 2000 Units/Bag MC78L09ACDR2G SOIC−8 (Pb−Free) 2500 Tape & Reel MC78L09ACPG TO−92 (Pb−Free) 2000 Units/Bag MC78L09ACD MC78L09ACDG 9.0 V MC78L09ACDR2 MC78L09ACDR2G MC78L09ACP TJ = 0° to +125°C †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 10 MC78L00A Series, NCV78L00A ORDERING INFORMATION Operating Temperature Range Package Shipping† MC78L12ABD SOIC−8 98 Units/Rail MC78L12ABDR2 SOIC−8 2500 Tape & Reel Device Output Voltage MC78L12ABP TO−92 2000 Units/Bag MC78L12ABPRP TO−92 2000 Ammo Pack NCV78L12ABDR2* SOIC_8 2500 Tape & Reel MC78L12ACD SOIC−8 98 Units/Rail MC78L12ACDR2 SOIC−8 2500 Tape & Reel MC78L12ACP TO−92 2000 Units/Bag MC78L12ACPRA TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack TO−92 2000 Ammo Pack MC78L12ACPRPG TO−92 (Pb−Free) 2000 Ammo Pack MC78L12ACDR2G SOIC−8 (Pb−Free) 2500 Tape & Reel MC78L12ACPG TO−92 (Pb−Free) 2000 Units/Bag MC78L15ABD SOIC−8 98 Units/Rail MC78L15ABDR2 SOIC−8 2500 Tape & Reel SOIC−8 (Pb−Free) 2500 Tape & Reel TJ = −40° to +125°C MC78L12ACPRAG 12 V MC78L12ACPRE MC78L12ACPRM TJ = 0° to +125°C MC78L12ACPRMG MC78L12ACPRP MC78L15ABDR2G MC78L15ABP TO−92 2000 Units/Bag MC78L15ABPRA TO−92 2000 Tape & Reel MC78L15ABPRP TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack MC78L15ABPRPG TJ = −40° to +125°C 15 V MC78L15ACD SOIC−8 98 Units/Rail MC78L15ACDR2 SOIC−8 2500 Tape & Reel MC78L15ACP TO−92 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 (Pb−Free) 2000 Tape & Reel TO−92 2000 Ammo Pack MC78L15ACPRA TJ = 0° to +125°C MC78L15ACPRAG MC78L15ACPRP *NCV78L12A: Tlow = −40°C, Thigh = +125°C. Guaranteed by design. NCV prefix is for automotive and other applications requiring site and change control. †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 11 MC78L00A Series, NCV78L00A ORDERING INFORMATION Operating Temperature Range Package Shipping† TJ = −40° to +125°C TO−92 2000 Units/Bag TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel MC78L18ACPRM TO−92 2000 Ammo Pack MC78L18ACPRP TO−92 2000 Ammo Pack TO−92 2000 Units/Bag TO−92 2000 Units/Bag TO−92 (Pb−Free) 2000 Units/Bag TO−92 2000 Tape & Reel TO−92 2000 Ammo Pack TO−92 (Pb−Free) 2000 Ammo Pack Device Output Voltage MC78L18ABP MC78L18ACP 18 V MC78L18ACPG MC78L18ACPRA 18 V MC78L24ABP TJ = 0° to t +125°C 125°C TJ = −40° to +125°C MC78L24ACP MC78L24ACPG MC78L24ACPRA 24 V TJ = 0° to +125°C MC78L24ACPRP MC78L24ACPRPG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 12 MC78L00A Series, NCV78L00A MARKING DIAGRAMS SOIC−8 D SUFFIX CASE 751 8 8 8LxxA ALYWB 8LxxA ALYWC 1 1 xx A L Y W B, C = 05, 08, 09, 12, or 15 = Assembly Location = Wafer Lot = Year = Work Week = Temperature Range TO−92 P SUFFIX CASE 029 MC78L zzABP ALYWW MC78L zzACP ALYWW 1 2 3 1 2 3 zz A L Y WW = 05, 08, 09, 12, 15, 18 or 24 = Assembly Location = Wafer Lot = Year = Work Week http://onsemi.com 13 MC78L00A Series, NCV78L00A PACKAGE DIMENSIONS TO−92 (TO−226) P SUFFIX CASE 29−11 ISSUE AL A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. B R P L SEATING PLANE K D X X G J H V C SECTION X−X 1 N N http://onsemi.com 14 DIM A B C D G H J K L N P R V INCHES MIN MAX 0.175 0.205 0.170 0.210 0.125 0.165 0.016 0.021 0.045 0.055 0.095 0.105 0.015 0.020 0.500 −−− 0.250 −−− 0.080 0.105 −−− 0.100 0.115 −−− 0.135 −−− MILLIMETERS MIN MAX 4.45 5.20 4.32 5.33 3.18 4.19 0.407 0.533 1.15 1.39 2.42 2.66 0.39 0.50 12.70 −−− 6.35 −−− 2.04 2.66 −−− 2.54 2.93 −−− 3.43 −−− MC78L00A Series, NCV78L00A SOIC−8 NB D SUFFIX CASE 751−07 ISSUE AB NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. −X− A 8 5 S B 1 0.25 (0.010) M Y M 4 K −Y− G C N X 45 DIM A B C D G H J K M N S SEATING PLANE −Z− 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 15 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0 8 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 8 0.010 0.020 0.228 0.244 MC78L00A Series, NCV78L00A ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Phone: 81−3−5773−3850 Email: [email protected] http://onsemi.com 16 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative. MC78L00A/D