AD AD781JNZ

AD781–SPECIFICATIONS
DC SPECIFICATIONS
(TMIN to TMAX, VCC = +12 V 6 10%, VEE = –12 V 6 10%, CL = 20 pF, unless otherwise noted)
Parameter
Min
AD781J
Typ
SAMPLING CHARACTERISTICS
Acquisition Time
10 V Step to 0.01%
10 V Step to 0.1%
Small Signal Bandwidth
Full Power Bandwidth
HOLD CHARACTERISTICS
Effective Aperture Delay (25°C)
Aperture Jitter (25°C)
Hold Settling (to 1 mV, 25°C)
Droop Rate
Feedthrough (25°C)
(VIN = ± 5 V, 100 kHz)
–35
Max
600
500
4
1
700
600
–25
50
250
0.01
–15
75
500
1
Min
–35
–86
AD781A
Typ
Max
600
500
4
1
700
600
–25
50
250
0.01
–15
75
500
1
Min
–35
–86
AD781S
Typ
Max
Units
600
500
4
1
700
600
ns
ns
MHz
MHz
–25
50
250
0.01
–15
75
500
1
ns
ps
ns
µV/µs
–86
dB
1
ACCURACY CHARACTERISTICS
Hold Mode Offset
Hold Mode Offset Drift
Sample Mode Offset
Nonlinearity
Gain Error
OUTPUT CHARACTERISTICS
Output Drive Current
Output Resistance, DC
Total Output Noise (DC to 5 MHz)
Sampled DC Uncertainty
Hold Mode Noise (DC to 5 MHz)
Short Circuit Current
Source
Sink
INPUT CHARACTERISTICS
Input Voltage Range
Bias Current
Input Impedance
Input Capacitance
DIGITAL CHARACTERISTICS
Input Voltage Low
Input Voltage High
Input Current High (VIN = 5 V)
–4
–5
0.3
150
85
125
+3
–4
200
± 0.003
± 0.025
+5
0.5
–5
50
50
2
–1
10
50
± 0.002
± 0.01
–5
0.3
150
85
125
20
10
+5
250
–5
50
50
2
0.8
0
+3
–4
200
± 0.003
± 0.025
+5
0.5
0.3
150
85
125
10
± 12
4
80
75
95
± 13.2
6.5
+3
200
± 0.005
± 0.025
+5
0.5
20
10
+5
250
–5
50
50
2
0.8
2.0
2
–1
10
50
± 0.003
± 0.01
–5
20
10
2.0
POWER SUPPLY CHARACTERISTICS
Operating Voltage Range
± 10.8
Supply Current
+PSRR (+12 V ± 10%)
70
–PSRR (–12 V ± 10%)
65
Power Consumption
TEMPERATURE RANGE
Specified Performance
–1
10
50
± 0.002
± 0.01
175
± 10.8 ± 12
4
70
80
65
75
95
+70
–40
10
± 13.2
6.5
2
mA
Ω
µV rms
µV rms
µV rms
mA
mA
+5
250
V
nA
MΩ
pF
0.8
V
V
µA
2.0
2
mV
µV/°C
mV
% FS
% FS
10
175
± 10.8 ± 12
4
70
80
65
75
95
± 13.2
7
185
V
mA
dB
dB
mW
+85
–55
+125
°C
NOTE
1
Specified and tested over an input range of ± 5 V.
Specifications subject to change without notice.
Specifications shown in boldface are tested on all devices at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min and max
specifications are guaranteed although only those shown in boldface are tested.
–2–
REV. A
AD781
(TMIN to TMAX, VCC = +12 V 6 10%, VEE = –12 V 6 10%, CL = 20 pF,
unless otherwise noted)1
HOLD MODE AC SPECIFICATIONS
Parameter
Min
AD781J
Typ
TOTAL HARMONIC DISTORTION
FIN = 10 kHz
FIN = 50 kHz
FIN = 100 kHz
–90
–73
–68
SIGNAL-TO-NOISE AND DISTORTION
FIN = 10 kHz
72
FIN = 50 kHz
FIN = 100 kHz
78
73
67
INTERMODULATION DISTORTION
FIN1 = 49 kHz, FIN2 = 50 kHz
2nd Order Products
3rd Order Products
–77
–78
Max
Min
–80
AD781A
Typ
Max
–90
–73
–68
72
Min
–80
78
73
67
AD781S
Typ
–90
–73
–68
72
–77
–78
Max
Units
–80
dB
dB
dB
78
73
67
dB
dB
dB
–77
–78
dB
dB
NOTE
1
FIN amplitude = 0 dB and F SAMPLE = 500 kHz unless otherwise indicated.
Specifications shown in boldface are tested on all devices at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min and max
specifications are guaranteed although only those shown in boldface are tested.
Specifications subject to change without notice.
ABSOLUTE MAXIMUM RATINGS*
Spec
VCC
VEE
Control Input
Analog Input
Output Short Circuit to
Ground, VCC, or VEE
Maximum Junction
Temperature
Storage
Lead Temperature
(10 sec max)
Power Dissipation
PIN CONFIGURATION
With
Respect to
Min
Max
Unit
Common
Common
Common
Common
–0.3
–15
–0.5
–12
+15
+0.3
+7
+12
V
V
V
V
VCC
1
IN
2
COMMON
3
NC
4
AD781
TOP VIEW
(Not to Scale)
8
OUT
7
S/H
6
NC
5
VEE
Indefinite
–65
+175
+150
+300
195
°C
°C
ORDERING GUIDE
Model1
°C
mW
Temperature
Range
AD781JN 0°C to +70°C
AD781AN –40°C to +85°C
AD781SQ –55°C to +125°C
*Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the
operational section of this specification is not implied.
Description
Package
Options2
8-Pin Plastic DIP N-8
8-Pin Plastic DIP N-8
8-Pin Cerdip
Q-8
NOTES
1
For details on grade and package offerings screened in accordance with
MIL-STD-883, refer to the Analog Devices Military Products Databook or
current AD781/883B data sheet.
2
N = Plastic DIP; Q = Cerdip.
CAUTION
ESD (electrostatic discharge) sensitive device. The digital control inputs are diode protected;
however, permanent damage may occur on unconnected devices subject to high energy electrostatic fields. Unused devices must be stored in conductive foam or shunts.
WARNING!
ESD SENSITIVE DEVICE
REV. A
–3–
AD781
80
EFFECTIVE APERTURE DELAY – ns
70
V+
1.0
DROOP RATE – µV/µs
60
PSRR – dB
–10
10.0
50
V–
40
30
20
0.1
0.01
10
0
0.001
1
100
10
1k
10k
100k
0
1M
25
50
75
100
125
–15
–20
–25
–30
100
150
1k
TEMPERATURE – °C
FREQUENCY – Hz
Power Supply Rejection Ratio vs.
Frequency
Droop Rate vs. Temperature,
VIN = 0 V
100k
1M
Effective Aperture Delay vs.
Frequency
5
200
10k
FREQUENCY – Hz
5
50
0
–50
–100
SUPPLY CURRENT – mA
SUPPLY CURRENT – mA
100
4
3
2
4
3
2
–150
–200
–10
–5
0
5
1
–75 –50 –25
10
1
0
25
50
75 100 125 150
TEMPERATURE – °C
INPUT VOLTAGE – V
Bias Current vs. Input Voltage
±10
±11
±12
±13
±14
±15
SUPPLY VOLTAGE – V
Supply Current vs. Temperature
Supply Current vs. Supply Voltage
1000
ACQUISITION TIME – ns
BIAS CURRENT – nA
150
750
500
250
0
0
2
4
6
8
10
INPUT STEP – V
Acquisition Time (to 0.01%) vs.
Input Step Size
–4–
REV. A
AD781
Signal-To-Noise and Distortion (S/N+D) Ratio—S/N+D is
the ratio of the rms value of the measured input signal to the
rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
S/N+D is expressed in decibels.
DEFINITIONS OF SPECIFICATIONS
Acquisition Time—The length of time that the SHA must
remain in the sample mode in order to acquire a full-scale input
step to a given level of accuracy.
Small Signal Bandwidth—The frequency at which the held
output amplitude is 3 dB below the input amplitude, under an
input condition of a 100 mV p-p sine wave.
Total Harmonic Distortion (THD)—THD is the ratio of the
rms sum of the first six harmonic components to the rms value
of the measured input signal and is expressed as a percentage or
in decibels.
Full Power Bandwidth—The frequency at which the held
output amplitude is 3 dB below the input amplitude, under an
input condition of a 10 V p-p sine wave.
Intermodulation Distortion (IMD)—With inputs consisting
of sine waves at two frequencies, fa and fb, any device with
nonlinearities will create distortion products, of order (m+n), at
sum and difference frequency of mfa± nfb, where m, n = 0, 1, 2,
3.... Intermodulation terms are those for which m or n is not
equal to zero. For example, the second order terms are (fa+fb)
and (fa–fb), and the third order terms are (2fa+fb), (2fa–fb),
(fa+2fb) and (fa–2fb). The IMD products are expressed as the
decibel ratio of the rms sum of the measured input signals to the
rms sum of the distortion terms. The two signals are of equal
amplitude, and peak value of their sums is –0.5 dB from full
scale. The IMD products are normalized to a 0 dB input signal.
Effective Aperture Delay—The difference between the switch
delay and the analog delay of the SHA channel. A negative
number indicates that the analog portion of the overall delay is
greater than the switch portion. This effective delay represents
the point in time, relative to the hold command, that the input
signal will be sampled.
Aperture Jitter—The variations in aperture delay for
successive samples. Aperture jitter puts an upper limit on the
maximum frequency that can be accurately sampled.
Hold Settling Time—The time required for the output to
settle to within a specified level of accuracy of its final held value
after the hold command has been given.
FUNCTIONAL DESCRIPTION
The AD781 is a complete sample-and hold amplifier that
provides high speed sampling to 12-bit accuracy in less than
700 ns.
Droop Rate—The drift in output voltage while in the hold
mode.
Feedthrough—The attenuated version of a changing input
signal that appears at the output when the SHA is in the hold
mode.
The AD781 is completely self-contained, including an on-chip
hold capacitor, and requires no external components or
adjustments to perform the sampling function. Both input and
output are treated as a single-ended signal, referred to common.
Hold Mode Offset—The difference between the input signal
and the held output. This offset term applies only in the hold
mode and includes the error caused by charge injection and all
other internal offsets. It is specified for an input of 0 V.
The AD781 utilizes a proprietary circuit design which includes a
self-correcting architecture. This sample-and-hold circuit
corrects for internal errors after the hold command has been
given, by compensating for amplifier gain and offset errors, and
charge injection errors. Due to the nature of the design, the
SHA output in the sample mode is not intended to provide an
accurate representation of the input. However, in hold mode,
the internal circuitry is reconfigured to produce an accurately
held version of the input signal. Below is a block diagram of the
AD781.
Tracking Mode Offset—The difference between the input and
output signals when the SHA is in the track mode.
Nonlinearity--The deviation from a straight line on a plot of
input vs. (held) output as referenced to a straight line drawn
between endpoints, over an input range of –5 V and +5 V.
Gain Error—Deviation from a gain of +1 on the transfer
function of input vs. held output.
Power Supply Rejection Ratio—A measure of change in the
held output voltage for a specified change in the positive or
negative supply.
Sampled DC Uncertainty—The internal rms SHA noise that
is sampled onto the hold capacitor.
1
IN
2
8
OUT
7
S/H
6
NC
5
VEE
X1
Hold Mode Noise—The rms noise at the output of the SHA
while in the hold mode, specified over a given bandwidth.
Total Output Noise—The total rms noise that is seen at the
output of the SHA while in the hold mode. It is the rms
summation of the sampled dc uncertainty and the hold mode
noise.
COMMON
3
NC
4
AD781
Functional Block Diagram
Output Drive Current—The maximum current the SHA can
source (or sink) while maintaining a change in hold mode offset
of less than 2.5 mV.
REV. A
VCC
–5–
AD781
DYNAMIC PERFORMANCE
(VOUT HOLD – VIN ), mV
VOUT ACQUISITION ACCURACY – %
The AD781 is compatible with 12-bit A-to-D converters in
terms of both accuracy and speed. The fast acquisition time, fast
hold settling time and good output drive capability allow the
AD781 to be used with high speed, high resolution A-to-D
converters like the AD674 and AD7672. The AD781’s fast
acquisition time provides high throughput rates for multichannel
data acquisition systems. Typically, the sample and hold can
acquire a 10 V step in less than 600 ns. Figure 1 shows the
settling accuracy as a function of acquisition time.
+1
V IN , VOLTS
–4
–5
–3
–2
–1
3
2
1
4
+5
HOLD MODE OFFSET
0.08
–1
GAIN ERROR
0.06
NONLINEARITY
0.04
Figure 3. Hold Mode Offset, Gain Error and Nonlinearity
0.02
0
0
250
500
750
1000
ACQUISITION TIME – ns
For applications where it is important to obtain zero offset, the
hold mode offset may be nulled externally at the input to the
A-to-D converter. Adjustment of the offset may be accomplished through the A-to-D itself or by an external amplifier
with offset nulling capability (e.g., AD711). The offset will
change less than 0.5 mV over the specified temperature range.
Figure 1. VOUT Settling vs. Acquisition Time
The hold settling determines the required time, after the hold
command is given, for the output to settle to its final specified
accuracy. The typical settling behavior of the AD781 is shown
in Figure 2. The settling time of the AD781 is sufficiently fast to
allow the SHA, in most cases, to directly drive an A-to-D
converter without the need for an added “start convert” delay.
SUPPLY DECOUPLING AND GROUNDING
CONSIDERATIONS
As with any high speed, high resolution data acquisition system,
the power supplies should be well regulated and free from excessive high frequency noise (ripple). The supply connection to the
AD781 should also be capable of delivering transient currents to
the device. To achieve the specified accuracy and dynamic performance, decoupling capacitors must be placed directly at both
the positive and negative supply pins to common. Ceramic type
0.1 µF capacitors should be connected from VCC and VEE to
common.
ANALOG
P.S.
C
+12V
0.1µF
DIGITAL
P.S.
–12V
0.1µF
C
1µF
1µF
+5V
1µF
+
INPUTS
Figure 2. Typical AD781 Hold Mode
AD781
HOLD MODE OFFSET
The dc accuracy of the AD781 is determined primarily by the
hold mode offset. The hold mode offset refers to the difference
between the final held output voltage and the input signal at the
time the hold command is given. The hold mode offset arises
from a voltage error introduced onto the hold capacitor by
charge injection of the internal switches. The nominal hold
mode offset is specified for a 0 V input condition. Over the
input range of –5 V to +5 V, the AD781 is also characterized for
an effective gain error and nonlinearity of the held value, as
shown in Figure 3. As indicated by the AD781 specifications,
the hold mode offset is very stable over temperature.
7
9
11 15
AD674
1
DIGITAL
DATA
OUTPUT
SIGNAL GROUND
Figure 4. Basic Grounding and Decoupling Diagram
The AD781 does not provide separate analog and digital ground
leads as is the case with most A-to-D converters. The common
pin is the single ground terminal for the device. It is the reference point for the sampled input voltage and the held output
voltage and also the digital ground return path. The common
pin should be connected to the reference (analog) ground of the
A-to-D converter with a separate ground lead. Since the analog
and digital grounds in the AD781 are connected internally, the
–6–
REV. A
AD781
Measurements of Figures 7 and 8 were made using a 14-bit A/D
converter with VIN = 10 V p-p and a sample frequency of
100 kSPS.
common pin should also be connected to the digital ground,
which is usually tied to analog common at the A-to-D converter.
Figure 4 illustrates the recommended decoupling and grounding
practice.
1%
NOISE CHARACTERISTICS
1/2 BIT @
8 BITS
Designers of data conversion circuits must also consider the
effect of noise sources on the accuracy of the data acquisition
system. A sample-and-hold amplifier that precedes the A-to-D
converter introduces some noise and represents another source
of uncertainty in the conversion process. The noise from the
AD781 is specified as the total output noise, which includes
both the sampled wideband noise of the SHA in addition to the
band limited output noise. The total output noise is the rms
sum of the sampled dc uncertainty and the hold mode noise. A
plot of the total output noise vs. the equivalent input bandwidth
of the converter being used is given in Figure 5.
0.1%
1/2 BIT @
10 BITS
1/2 BIT @
12 BITS
0.01%
1/2 BIT @
14 BITS
APERTURE JITTER TYPICAL AT 50ps
1k
300
10k
100k
1M
FREQUENCY – Hz
–65
200
–70
–75
100
THD – dB
OUTPUT NOISE – µV rms
Figure 6. Error Magnitude vs. Frequency
–80
–85
0
1k
10k
100k
1M
10M
FREQUENCY – Hz
–90
Figure 5. RMS Noise vs. Input Bandwidth of ADC
–95
100
DRIVING THE ANALOG INPUTS
100k
10k
1M
Figure 7. Total Harmonic Distortion vs. Frequency
90
80
S/(N + D) – dB
70
HIGH FREQUENCY SAMPLING
Aperture jitter and distortion are the primary factors which limit
frequency domain performance of a sample-and-hold amplifier.
Aperture jitter modulates the phase of the hold command and
produces an effective noise on the sampled analog input. The
magnitude of the jitter induced noise is directly related to the
frequency of the input signal.
60
50
40
30
20
10
0
100
A graph showing the magnitude of the jitter induced error vs.
frequency of the input signal is given in Figure 6.
1k
10k
100k
FREQUENCY – Hz
Figure 8. Signal/(Noise and Distortion) vs. Frequency
The accuracy in sampling high frequency signals is also constrained by the distortion and noise created by the sample-and
hold. The level of distortion increases with frequency and reduces the “effective number of bits” of the conversion.
REV. A
1k
FREQUENCY – Hz
For best performance, it is important to drive the AD781 analog
input from a low impedance signal source. This enhances the
sampling accuracy by minimizing the analog and digital
crosstalk. Signals which come from higher impedance sources
(e.g., over 5 kΩ) will have a relatively higher level of crosstalk.
For applications where signals have high source impedance, an
operational amplifier buffer in front of the AD781 is required.
The AD711 (precision BiFET op amp) is recommended for
these applications.
–7–
AD781
AD781 TO AD674 INTERFACE
20
Figure 9 shows a typical data acquisition circuit using the
AD781, a high linearity, low aperture jitter SHA and the AD674
a 12-bit high speed ADC. The time between the AD674 status
line going high and the actual start of conversion allows the
AD781 to settle to 0.01%. As a result, the AD674 status line
can be used to control the AD781; only an inverter is needed to
interface the two devices.
0
STATUS
–40
C1509–10–2/91
AMPLITUDE – dB
–20
–60
–80
–100
+5V
7404
OR EQUIV.
+12V
CE 12/8
28 STS
0.1µF
–120
0.1µF
1
2
6
VL
–140
0
2
6
IN
OUT
3
8
5
AD674
13 10 V
IN
AD781
GND
16
NC 14 20 VIN
VEE
13
16
20
23
26
30
33
D0–11
27
12-BIT
THREE-STATE
DATA
GAIN
10 REF IN
0.1µF
100Ω
–12V
8
REF OUT
100Ω
12 BIP OFFSET
OFFSET
5 R/C
CONVERT
9 AGND
7
11
+12V
4.7µF
–12V
0.1µF
0.1µF
4.7µF
Figure 9. AD781 to AD674 Interface
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
Cerdip (Q) Package
Mini-DIP (N) Package
PRINTED IN U.S.A.
VIN
4 A0
NC
10
Figure 10. FFT Plot of AD781 to AD674 Interface,
FIN = 1 kHz
3 CS
4 NC
S/H
7
FREQUENCY BINS – kHz
15 DGND
7
1
VCC
3
–8–
REV. A