CREE CA12816-LXP2-RS2

PRODUCT DATASHEET
Leila series
last update 2/5/2012
Ordering number CA12816_LXP2-RS2
Family
Type
LED
Color
Diameter
Height
Style
Optic Material
Holder Material
Fastening
Status
Leila
Assembly
XT-E
Black
21.6 mm
14.6 mm
Round
PMMA
PC
Tape
Ready
FWHM
Efficiency
cd/lm
Gerber File
8 degrees
92 %
15.600
Available
FWHM
Efficiency
cd/lm
Gerber File
11 degrees
88 %
8.950
Available
FWHM
Efficiency
cd/lm
Gerber File
14+36 degrees
84 %
3.860
Available
FWHM
Efficiency
cd/lm
Gerber File
24 degrees
88 %
3.900
Available
Ordering number CA11482_LXP2-D
Family
Type
LED
Color
Diameter
Height
Style
Optic Material
Holder Material
Fastening
Status
Leila
Assembly
XT-E
Black
21.6 mm
14.6 mm
Round
PMMA
PC
Tape
Ready
Ordering number CA11484_LXP2-O-90
Family
Type
LED
Color
Diameter
Height
Style
Optic Material
Holder Material
Fastening
Status
Leila
Assembly
XT-E
Black
21.6 mm
14.5 mm
Round
PMMA
PC
Tape
Ready
Ordering number CA11483_LXP2-M
Family
Type
LED
Color
Diameter
Height
Style
Optic Material
Holder Material
Fastening
Status
Leila
Assembly
XT-E
Black
21.6 mm
14.6 mm
Round
PMMA
PC
Tape
Ready
October 19th 2012 0:31 Copyright Ledil Oy - Subject to change without prior notice - Page 1/3
Ledil Oy
Salorankatu 10
24240 SALO
Finland
http://www.ledil.com
email: ledil@ledil.com
FAX: +358-2-733 8001
PRODUCT DATASHEET
Leila series
last update 2/5/2012
Ordering number CA12392_LXP2-W
Family
Type
LED
Color
Diameter
Height
Style
Optic Material
Holder Material
Fastening
Status
Leila
Assembly
XT-E
Black
21.6 mm
14.6 mm
Round
PMMA
PC
Tape
Ready
FWHM
Efficiency
cd/lm
Gerber File
41 degrees
89 %
1.580
Available
NOTE: The typical divergence will be changed by different color, chip size and chip position
tolerance. The typical total divergence is the full angle measured where the luminous intensity
is half of the peak value.
October 19th 2012 0:31 Copyright Ledil Oy - Subject to change without prior notice - Page 2/3
Ledil Oy
Salorankatu 10
24240 SALO
Finland
http://www.ledil.com
email: ledil@ledil.com
FAX: +358-2-733 8001
PRODUCT DATASHEET
Leila series
last update 2/5/2012
GENERAL INFORMATION
- Product series especially designed & optimized for XT-E series of LEDs.
- Special care taken to make light distribution as uniform as possible.
- Lens material optical grade PMMA with high UV and temperature resistance (105 degrees of Celcius / 220
degrees of Fahrenheit). Allows use of high current and temperature conditions.
Please find more information about used material from below:
http://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20UL94_Yellow%20Card.pdf
http://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20PLEXIGLAS-Datasheet.pdf
- Optic holder molded by high quality PC material (120 dergees of Celcius / 248 degrees of Fahrenheit).
- Fastening to heat sink with a PU foam adhesive tape of automotive grade. Please find fastening details by
clicking link: http://www.ledil.com/datasheets/DataSheet_TAPE.pdf
NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end
product. For example, mechanical stress, vibration and holes on the surface of the circuit boar
weaken the strength of the tape.
NOTE 2: Assembly to the surface must be made straight, so the tape bonds constant and
balanced with fastening surface. Slanted assembly might cause unbalanced bond to the
surface. All surfaces where tape is applied must be clean, dry and free from grease and dirt.
If cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your
LED manufacturer - this is important as cleaning shall under no circumstances damage LEDs or
other electronics components on the PCB.
Further note that optical components shall not be cleaned with any chemicals - only micro fiber
cloth may be used to remove fingerprints or other traces from handling.
October 19th 2012 0:31 Copyright Ledil Oy - Subject to change without prior notice - Page 3/3
Ledil Oy
Salorankatu 10
24240 SALO
Finland
http://www.ledil.com
email: ledil@ledil.com
FAX: +358-2-733 8001
A
B
C
D
4
4
Tape 0.4mm
Isometric view
Scale: 1:1
14.6
3
3
21
2
MATERIALS
Lens: PMMA
Holder: PC
Tape: PU Foam
Part no.s:
CA11481_LXP2-RS
CA11481_LXP2-G-RS
CA11482_LXP2-D
CA11482_LXP2-G-D
CA11483_LXP2-M
CA11483_LXP2-G-M
CA11484_LXP2-O-90
CA11484_LXP2-G-O-90
1
This drawing is our property.
It can't be reproduced
or communicated without
our written agreement.
DRAWN BY
DATE
CHECKED BY
DATE
DESIGNED BY
DATE
.6
2
Oval-version beam direction
Led
Teh
FIN
Fin
DRAWING TITLE
Datasheet Leila LXP2-Series assy
pv
02.12.2010
tk
12.04.2010
pv
12.04.2010
D
SIZE
DRAWING NUMBER
REV
1
A4
SCALE
2:1 WEIGHT(g)
-
SHEET
A
1/1
1