Front Back AGGP.35F.07.0060A Specification Part No. AGGP.35F.07.0060A Product Name 35mm Two Stage 28dB GPS-Glonass- GNSS Active Patch Antenna Module with Front-end Saw Filter Features Industry leading GPS~GLONASS antenna performance 35*35*6.9mm (Ground Plane) 60mm Ø1.13 IPEX MHFI (U.FL) 28dB LNA Wide Input Voltage 1.8V to 5.5V Low Power Consumption ROHS Compliant SPE-12-8-018/D/SS | page 1 of 12 1. Introduction The AGGP.35F GPS – Glonass- GNSS active patch antenna (along with the AGGP.25 model) is the best choice to use as an embedded antenna with the latest generation of GPS-Glonass-GNSS receivers. The AGGP.35F aslo includes a two stage LNA and a front-end SAW filter to reduce out of band noise such as from nearby cellular transceiver, and improve probability of the wireless device passing radiated spurious emissions certification. It utliizes a 35*35*3.5mm advanced wide-band ceramic patch antenna with optimized gain, radiation patttern and axial ratio at GPS and Glonass centre frequencies. Produced in TS16949 automotive quality approved facility and 100% tested for gain (S21), return loss (S11) to ensure total consistency of performance. Cable type, length and connectors can be customized and samples offered according to requirement, subject to minimum order quantities in production. Taoglas also offers custom tuning service based on minimum order quantities, contact your local regional sales office for details. The AGGP.35F consists of 2 functional blocks – the LNA and also the patch antenna. ANTENNA SAW Filter LNA LNA Cable & Connector SPE-12-8-018/D/SS | page 2 of 12 2. Specification Electrical Parameter Specification Operation Frequency 1574 ~ 1610MHz Patch Gain 1575.42MHz, 1dBic typ. @ zenith 1602MHz, 0.5dBic typ. @ zenith Overall Gain 1575.42MHz, 27 ± 3dBic typ. @ zenith 1602MHz, 28.5 ± 3dBic typ. @ zenith Axial Ratio 3.0dB max @ zenith Polarization Right Hand Circular VSWR 2.0 :1 max Impedance 50Ω DC input 1.8V min. 3.0V 5.5V max. LNA Gain 22dB 28dB 31dB Noise Figure 2.6dB 2.6dB 2.9dB Power Consumption 5mA 10mA 23mA Band Attenuation 15dB @ 1592 ± 140MHz Mechanical Parameter Specification Antenna Dimensions 35 x 35 x 3.7mm Material Ceramic Cable 60mm 1.13 co-axial Connector IPEX MHF1 Environmental Parameter Specification Operation Temperature -40°C to 85°C Storage Temperature -40°C to 105°C Relative Humidity 40% to 95% SPE-12-8-018/D/SS | page 3 of 12 3. LNA Gain and Out Band Rejection @3.0V Tr1 S21 Log Mag 10.00dB/ Ref 0.000dB [F2 smo] Tr1 S22 SWR 1.000/ Ref 1.000 [F2 smo] 40.00 >2 1.6100000 GHz 27.949 dB 2 30.00 1 20.00 3 10.00 4 0.000 6 1 -10.00 5 -20.00 7 -30.00 -40.00 -50.00 2 -60.00 6 4 1 Center 1.592 GHz Ch1 Ch1 Ch1 Ch1 Ch1 Ch1 Ch1 Tr1 Tr1 Tr1 Tr1 Tr1 Tr1 Tr1 S21 S21 S21 S21 S21 S21 S21 1 >2 3 4 5 6 7 1 3 IFBW 1 kHz 1.5740000 1.6100000 1.5920000 1.5420000 1.6420000 1.4920000 1.6920000 GHz GHz GHz GHz GHz GHz GHz 28.186 27.949 29.044 9.0245 -10.035 4.4105 -14.431 2 5 7 Span 400 MHz 5/16 Cor dB dB dB dB dB dB dB SPE-12-8-018/D/SS | page 4 of 12 4. LNA Noise Figure @3.0V Mkr1 1.592 GHz 2.558 dB 30.030 dB 19.00 NFIG Scale/ 2.000 dB 1 -1.000 40.00 1 GAIN Scale/ 5.000 dB -10.00 Center 1.57400 GHz BW 4 MHz Tcold 296.50 K Avgs Off Points 11 Att 0/ - - dB Stop 1.61000 GHz Loss Off Corr 5. Total Specification (through Antenna, LNA, Cable and Connector) Parameter Specification Frequency 1574~1610MHz Gain at 90° 1575.42MHz: 27 ± 3dBic 1602MHz: 28.5 ± 3dBic Output Impedance 50Ω Polarization RHCP Output VSWR Max 2.0 Operation Temperature -40°C to + 85°C Storage Temperature -40°C to + 85°C Relative Humidity 40% to 95% Input Voltage Min. 1.8V, Typ. 3.0V, Max. 5V Antenna 35*35*6.9mm SPE-12-8-018/D/SS | page 5 of 12 6. Radiation Patterns Z Y X SPE-12-8-018/D/SS | page 6 of 12 6. Radiation Patterns 6.1 1575.42MHz XZ & YZ Plane 0 2 -5 -10 -15 -20 -25 -30 -35 -40 90 270 -45 180 Pattern Peak Gain (dBic) Average Gain (dBi) 1 XZ Plane Radiation -0.6 @ 350° -3.2 2 YZ Plane Radiation -0.2 @ 0° -2.1 (unit : dBi) SPE-12-8-018/D/SS | page 7 of 12 6.2 1602MHz XZ &YZ Plane 0 5 0 -5 -10 -15 -20 -25 -30 -35 -40 90 270 -45 180 Pattern Peak Gain (dBic) Average Gain (dBi) 1 XZ Plane Radiation 0.9 @ 337° -1.8 2 YZ Plane Radiation 0.8 @ 348° -1.2 (unit : dBi) SPE-12-8-018/D/SS | page 8 of 12 7. Plugs Usage Precautions 7.I Mating / unmating (1) To disconnect connectors, insert the end portion of I-PEX under the connector flanges and pull off vertically, in the direction of the connector mating axis. Coaxial Cable (2) To mate the connectors, the mating axes of both connectors must be aligned and the connectors can be mated. The “click” will confirm fully mated connection. Do not attempt to insert on an extreme angle. 2 PLUG 1 Pulling Tool P/N : 90192-001 RECEPTACLE 7.2 Pull forces on the cable after connectors are mated After the connectors are mated, do not apply a load to the cable in excess of the values indicated in the diagram below. 2N MAX. PLUG 4N MAX. 2N MAX. RECE Coaxial Cable SPE-12-8-018/D/SS | page 9 of 12 IPEX MHFI A ALL Initial Design Sandy 2011/11/28 B E3 Sandy 2011/12/27 C C2 Sandy 2012/01/31 B B IPEX MHF 1 C Top 2011/11/23 2011/9/6 2011/12/27 2011/11/21 2012/01/31 "A" B AGGP.25F Top Sandy Kiwi Sandy Sandy Sandy AGGP.35F 8. Technical Drawing Amend Shielding Case Drawing ALL Initial Design ALL Initial Design E3 Amend Logo Placement E2 Add LOGO C2 Amend Shielding Case Drawing A A IPEX MHFI Amend Logo Placement Top "A" B C AP.10E Side B Side C Bottom Side Bottom C Bottom NOTE: 1.Soldered area "A" 2.Shielding case area 3.All material must be RoHS compliant. 4.The connector orientation has a fixed position to the antenna as per drawing. NOTE: P/N Name Finish Material AGGP.35F Patch(35*35*3.7mm) AGGP.35F Ceramic Clear 1 2 1.13 Coaxial Cable OD.113.CM FEP Gray 1 P/N IPEX.MHFI.113 Material Brass Finish Gold 1 Name IPEX MHF1 Connector 3 FinishClear 1 AGGP.35F Patch (35*35*3.7mm) P/NAGGP.35F Material Name MaterialCeramicFinish QTY Name P/N QTY NOTE: NOTE: 4 PCB Green FR4 0.8t 1.Soldered area 1. Soldered area 1.Soldered area 1 AGGP.25F Patch(25*25*4.2mm) AGGP.25F Ceramic Clear AP.10E Patch(10*10*4mm) AP.10E 1 2 Ceramic FEP Clear Gray 11 1.13 Coaxial Cable OD.113.CM 2.Shielding case Tin Plated 2.Shielding casearea area 5 Shielding Case (Tin)SPTE 2. Shielding case area FEP 2 1.13 Coaxial Cable Gray OD.113.CM 1 3.All material must bebeRoHS material mustbe RoHScompliant. compliant. FEP Coaxial Cable IPEX MHF1 Connector OD.081.CM IPEX.MHFI.113 BrassGray Gold 1 3. All3.All material must RoHS compliant. 2 3 0.81 4.The 4.Theconnector connectororientation orientationhas hasa afixed fixed IPEX MHF1 Connector Gold 1 3 IPEX.MHFI.113 Brass 4. The connector orientation has a fixed position MHF1 IPEX.MHFI.113 Brass Gold positiontotothe theantenna antennaasasper perdrawing. drawing. 3 4 IPEX PCB FR4 0.8t Green1 TW Design Centre position to the antenna as per drawing. 4 PCB Green 1 FR4 0.8t This drawing and its inherent concepts are property Taoglas. Not to Tin design (SPTE) 4 5 Shielding CaseCase Tin ofPlated 1 Shielding (Tin)SPTE Tin Plated be copied or given to third parties without the written consent of Taoglas. 5 5 QTY 1 PCB Shielding Case (Tin)SPTE FR4 0.5t Tin Plated Green 1 QTY 1 1 1 1 1 1 1 1 TW Design Centre This drawing and its inherent design concepts are property Taoglas. Not to TW of Design Centre be copied or given to third parties without the written consent of Taoglas. This drawing and its inherent design concepts are property of Taoglas. Not to be copied or given to third parties without the written consent of Taoglas. SPE-12-8-018/D/SS | page 10 of 12 8.1 Connector Drawing IPEX MHFI Top A ALL Initial Design B E3 C C2 Amend Logo Placement Amend Shielding Case Drawin "A" B Side Bottom SPE-12-8-018/D/SS | page 11 of 12 5 包裝規格 9. 5.1 每個 tray 放置 30 天線 【30pcs antennas per tray】 Packaging 5.2 每 6 個 tray 包裝成 1 組, 【Stack up 6 trays together】 Packaged in plastic tray with foam 5.3 每箱放置 3 組 tray,總共 540pcs 天線 comparment in tray contains 1 pcs of AGGP.35F 【3 sets per box. i.e.540pcs antenna per Each box.】 30 pcs of antenna per tray 5.4 包裝時須注意不可壓到天線,裝入需平整不可雜亂 【Antenna should be placed flat and neat, packing without pressing or damage the antenna】 5.5 清點每 tray 數量不可短缺 【Confirm the quantity in each tray】 AGGP.35F AGGP.35F 6 trays together in one section Tray 箱子3 sections per carton 540 pcs of antenna per carton Taoglas makes no warranties based on the product descriptions at any time accuracy or completeness of the contents without notice. of this document andSPECIFIED reserves the right to Taoglas reserves all rights to this document UNLESS OTHER TOLERANCES ON： make changes to specifications and and the information X＝± X.X＝± X.XX＝ ANGLES＝± HOLEDIA＝± SCALE： xxxx UNIT：mm DRAWN BY: jason CHECKED BY: Jimmy DESIGNED BY: Jimmy APPROVED BY: Jimmy contained herein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. Copyright © Taoglas Ltd. SPE-12-8-018/D/SS | page 12 of 12