SAC Transient 9ROWDJH6XSSUHVVRUV Series MERITEK FEATURES Plastic package has Underwriters Laboratory Flammability Classification 94V-O. Glass passivated junction. 500W peak pulse power capability with a 10/1000µs waveform, repetition rate (duty cycle): 0.01%. Excellent clamping capability. Low incremental surge resistance. Fast response time: typically less than 5.0ns from 0 volt to VBR min. Ideal for data line applications. DOA DO-204AC/DO-15 High temperature soldering guaranteed: 265℃/10 seconds/.375”, (9.5mm) lead length, 5lbs., (2.3kg) tension. MECHANICAL DATA M Case: JEDEC DO-15 molded plastic over a passivated junction. Terminals: Solder plated axial leads, solderable per MIL-STD-750, Method 2026. Polarity: Color band denotes cathode. Mounting Position: Any. Weight: 0.015 ounce, 0.4 grams. MM AXIMUM RATINGS AND CHARACTERISTICS Ratings at 25℃ ambient temperature unless otherwise specified. RATING SYMBOL VALUE UNIT Peak Pulse Power Dissipation on 10/1000μs waveform. (Note 1，Fig. 1) PPPM Minimum 500 Watts Peak Pulse Current on 10/1000μs waveform. (Note 1，Fig. 3) IPPM See Table Amps Steady State Power Dissipation at TL =75℃，Lead length .375” (9.5mm). PM(AV) 3.0 Watts TJ , TSTG -55 to +175 ( Fig. 5) Operating junction and Storage Temperature Range. ℃ Note: Non-repetitive current pulse, per Fig. 3 and derated above TA = 25℃ per Fig. 2. All specifications are subject to change without notice. 1 Rev 7 SAC Transient 9ROWDJH6XSSUHVVRUV Series MERITEK PACKAGE DIMENSIONS d s DIA. DIA. L T L DO-204AC/DO-15 Millimeters Item Inches Min. Max. Min. Max. L 25.40 - 1.000 - T 5.80 7.60 0.230 0.300 d 2.60 3.60 0.104 0.140 s 0.71 0.86 0.028 0.034 SPECIFICATIONS Minimum Reverse Breakdown Part Stand-Off Voltage Number Voltage @IT=1.0mA Maximum Peak Maximum Working Inverse Peak Inverse Blocking Inverse Junction Pulse Capacitance Blocking Leakage Blocking Current Voltage Current Voltage @0V FIG.3 Maximum Maximum Reverse Clamping Voltage Leakage @VRWM @IPP=5.0A VRWM(V) VBR(V) IR(µA) VC(V) IPP(A) pF VWIB(V) IIB(mA) VPIB(V) SAC5.0 5.0 7.60 300 10.0 44.0 50 75 1.0 100 SAC6.0 6.0 7.90 300 11.2 41.0 50 75 1.0 100 SAC7.0 7.0 8.33 300 12.6 38.0 50 75 1.0 100 SAC8.0 8.0 8.89 100 13.4 36.0 50 75 1.0 100 SAC8.5 8.5 9.44 50 14.0 34.0 50 75 1.0 100 SAC10 10.0 11.10 5 16.3 29.0 50 75 1.0 100 SAC12 12.0 13.30 1 19.0 25.0 50 75 1.0 100 SAC15 15.0 16.70 1 23.6 20.0 50 75 1.0 100 SAC18 18.0 20.00 1 28.8 15.0 50 75 1.0 100 SAC22 22.0 24.40 1 35.4 14.0 50 75 1.0 100 SAC26 26.0 28.90 1 42.3 11.1 50 75 1.0 100 SAC30 30.0 33.30 1 48.6 10.0 50 75 1.0 100 SAC36 36.0 40.00 1 60.0 8.6 50 75 1.0 100 SAC45 45.0 50.00 1 77.0 6.8 50 150 1.0 200 SAC50 50.0 55.50 1 88.0 5.8 50 150 1.0 200 2 Rev 7 SAC Transient 9ROWDJH6XSSUHVVRUV Series MERITEK RATING AND CHARACTERISTIC CURVES (TA: 25°C UNLESS OTHERWISE SPECIFIED) Figure 1 - Peak Pulse Power Rating Curve Figure 2 - Pulse Derating Curve 100 Percentage of Rated Power (%) PPPM-Peak Pulse Power (kW) 1000 100 10 1 0.1 0.000001 0.00001 0.0001 A verage Power 75 50 25 0 0.001 td-Pulse Width (Sec.) Figure 3 - Pulse Waveform Peak Power (Single Pulse) 0 25 50 75 100 125 150 TL Lead Temperature (ºC) 175 Figure 4 - AC Line Protection Application 150 IPPM - Peak Pulse Current, % RSM I tr=10µsec T J =2 5°C Pulse Width(td) is defined as the point where the peak current decays to50% of IPPM Peak Value IPPM 10 0 Half Value IPPM IPPM ( 50 2 ) 10/1000µsec. Waveform as defined by R.E.A Low Capacitance Application Note: Device must be used with two units in parallel, opposite in polarity as shown in circuit for AC signal line protection. td 0 1.0 0 2.0 3.0 4.0 t-Time (ms) Figure 5 - Steady State Power Dissipation Derating Curve Steady State Power dissipation (W) 3.5 3 2.5 2 1.5 1 0.5 0 0 25 50 75 100 125 150 175 200 T L -Lead Temperature (ºC) 3 Rev 7