T-13/4 Super Ultra-Bright LED Lamps Technical Data Features Applications • Very High Intensity • Exceptional Uniformity • Microtint Lens for Color Identification • Consistent Viewability All Colors: AlGaAs Red High Efficiency Red Yellow Orange Green Emerald Green • 15 ° and 25° Family • Tape and Reel Options Available • Binned for Color and Intensity • Ideal for Backlighting Front Panels* • Used for Lighting Switches • Adapted for Indoor and Outdoor Signs HLMP-C115 HLMP-C117 HLMP-C215 HLMP-C315 HLMP-C415 HLMP-C515 HLMP-C615 HLMP-C123 HLMP-C223 HLMP-C323 HLMP-C423 HLMP-C523 HLMP-C623 Description These non-diffused lamps are designed to produce a bright light source and smooth radiation pattern. A slight tint is added to the lens for easy color identification. This lamp has been designed with a 20 mil lead frame, enhanced flange, and tight meniscus controls, making it compatible with radial lead automated insertion equipment. 2 Selection Guide Color DH AS AlGaAs Red Yellow Orange Green Emerald Green 2θ1/2[1] 15 Standoff Leads No 25 Yes No 15 No 25 No 15 No 25 No 15 No 25 No 15 No 25 No 15 No 25 No Part Number HLMPC115 C115-O00xx C115-OP0xx C117-OP0xx C123 C123-L00xx C215 C215-M00xx C215-MN0xx C223 C223-L00xx C223-MN0xx C315 C315-L00xx C315-LM0xx C323 C323-K00xx C323-KL0xx C415 C415-M00xx C415-M0D0xx C415-MN0xx C423 C423-L00xx C423-LM0xx C515 C515-L00xx C515-LM0xx C523 C523-J00xx C523-KL0xx C615 C615-G00xx C623 C623-E00xx Luminous Intensity Iv (mcd) Min. Max. 290.0 – 290.0 – 290.0 1000.0 290.0 1000.0 90.2 – 90.2 – 138.0 – 138.0 – 138.0 400.0 90.2 – 90.2 – 138.0 400.0 147.0 – 147.0 – 147.0 424.0 96.2 – 96.2 – 96.2 294.0 138.0 – 138.0 – 138.0 – 138.0 400.0 90.2 – 90.2 – 90.2 276.0 170.0 – 170.0 170.0 490.0 69.8 – 69.8 – 111.7 340.0 17.0 – 17.0 – 6.7 – 6.7 – 3 Part Numbering System HLMP - C x xx - x x x xx Mechanical Options 00: Bulk 01: Tape & Reel, Crimped Leads 02: Tape & Reel, Straight Leads B2: Right Angle Housing, Even Leads UQ: Ammo Pack, Horizontal Leads Color Bin Options 0: Full Color Bin Distribution D: Color Bins 4 & 5 only Maximum Iv Bin Options 0: Open (No Maximum Limit) Others: Please refer to the Iv Bin Table Minimum Iv Bin Options Please refer to the Iv Bin Table Viewing Angle & Standoffs Options 15: 15 Degree, without Standoffs 17: 15 Degree, with Standoffs 23: 25 Degree, without Standoffs Color Options 1. AS AlGaAs Red 2. High Efficiency Red 3. Yellow 4. Orange 5. Green 6. Emerald Green Package Options C: T-1 3/4 (5 mm) 4 Package Dimensions 5.00 ± 0.20 (0.197 ± 0.008) 5.00 ± 0.20 (NOTE 1) (0.197 ± 0.008) 8.71 ± 0.20 (0.343 ± 0.008) 1.14 ± 0.20 (0.045 ± 0.008) 12.60 ± 0.18 (0.496 ± 0.007) 8.71 ± 0.20 (0.343 ± 0.008) 1.14 ± 0.20 (0.045 ± 0.008) 1.85 (0.073) MAX. 31.60 MIN. (1.244) 31.60 MIN. (1.244) 0.70 (0.028) MAX. 1.50 ± 0.15 (0.059 ± 0.006) 0.70 (0.028) MAX. CATHODE LEAD CATHODE LEAD 1.00 MIN. (0.039) 0.50 ± 0.10 SQ. TYP. (0.020 ± 0.004) 1.00 MIN. (0.039) 5.80 ± 0.20 (0.228 ± 0.008) CATHODE FLAT CATHODE FLAT 2.54 ± 0.38 (0.100 ± 0.015) 0.50 ± 0.10 SQ. TYP. (0.020 ± 0.004) 5.80 ± 0.20 (0.228 ± 0.008) 2.54 ± 0.38 (0.100 ± 0.015) NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 2. LEADS ARE MILD STEEL, SOLDER DIPPED. 3. AN EPOXY MENISCUS MAY EXTEND ABOUT 0.5 mm (0.020 in.) DOWN THE LEADS. HLMP-Cx15 and HLMP-Cx23 HLMP-Cx17 Absolute Maximum Ratings at TA = 25°C Parameter Current[1] DC Forward Transient Forward Current [2] (10 µsec Pulse) Reverse Voltage (Ir = 100 µA) LED Junction Temperature Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [1.6 mm (0.063 in.) from body] DH AS AlGaAs Red High Efficiency Red and Orange 30 500 30 500 5 110 –20 to +100 5 110 Yellow High Performance Green and Emerald Green Units 20 500 30 500 mA mA 5 110 –20 to +100 V °C °C °C 5 110 –55 to +100 –55 to +100 260°C for 5 seconds Notes: 1. See Figure 5 for maximum current derating vs. ambient temperature. 2. The transient current is the maximum nonrecurring peak current the device can withstand without damaging the LED die and wire bond. 5 Electrical Characteristics at TA = 25°C Part Number HLMP-C115 HLMP-C117 HLMP-C123 HLMP-C215 HLMP-C223 HLMP-C315 HLMP-C323 HLMP-C415 HLMP-C423 HLMP-C515 HLMP-C523 HLMP-C615 HLMP-C623 Forward Voltage Vf (Volts) @ If = 20 mA Typ. Max. 1.8 2.2 Reverse Breakdown Vr (Volts) @ Ir = 100 µA Min. 5 Capacitance C (pF) Vf = 0 f = 1 MHz Typ. 30 Thermal Resistance RθJ-PIN (°C/W) 210 Speed of Response τs (ns) Time Constant e-t/τs Typ. 30 1.9 2.6 5 11 210 90 2.1 2.6 5 15 210 90 1.9 2.6 5 4 210 280 2.2 3.0 5 18 210 260 2.2 3.0 5 18 210 260 Optical Characteristics at TA = 25°C Part Number HLMP-C115 HLMP-C117 HLMP-C123 HLMP-C215 HLMP-C223 HLMP-C315 HLMP-C323 HLMP-C415 HLMP-C423 HLMP-C515 HLMP-C523 HLMP-C615 HLMP-C623 Luminous Intensity Iv (mcd) @ 20 mA[1] Min. Typ. 290 600 90 138 90 146 96 138 90 170 69 17 6 200 300 170 300 170 300 170 300 170 45 27 Peak Wavelength λpeak (nm) Typ. 645 Color, Dominant Wavelength λd[2] (nm) Typ. 637 635 626 583 585 600 602 568 570 558 560 Viewing Angle 2θ1/2 (Degrees)[3] Typ. 11 26 17 23 17 25 17 23 20 28 20 28 Luminous Efficacy ηv (lm/w) 80 145 500 380 595 656 Notes: 1. The luminous intensity, Iv, is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation pattern may not be aligned with this axis. 2. The dominant wavelength, λd, is derived from the CIE Chromaticity Diagram and represents the color of the device. 3. 2θ1/2 is the off-axis angle where the luminous intensity is 1/2 the on-axis intensity. 6 1.0 ORANGE EMERALD GREEN TA = 25° C TS AlGaAs RED RELATIVE INTENSITY DH As AlGaAs RED HIGH PERFORMANCE GREEN HIGH EFFICIENCY RED 0.5 YELLOW 0 500 550 600 650 700 750 WAVELENGTH – nm Figure 1. Relative Intensity vs. Wavelength. 300.0 200.0 DH As AlGaAs RED 100.0 TS AlGaAs RED 50.0 100 IF – FORWARD CURRENT – mA IF – FORWARD CURRENT – mA HIGH EFFICIENCY RED, ORANGE, YELLOW, AND HIGH PERFORMANCE GREEN, EMERALD GREEN 20.0 10.0 5.0 2.0 1.0 0.5 0.2 0.1 0 0.5 1.0 1.5 2.0 2.5 80 HIGH EFFICIENCY RED/ORANGE 60 YELLOW 40 20 0 3.0 3.5 HIGH PERFORMANCE GREEN, EMERALD GREEN 0 1.0 2.0 3.0 4.0 5.0 VF – FORWARD VOLTAGE – V VF – FORWARD VOLTAGE – V Figure 2. Forward Current vs. Forward Voltage (Non-resistor Lamp). HER, ORANGE, YELLOW, AND HIGH PERFORMANCE GREEN, EMERALD GREEN 1.6 2.0 DH As AlGaAs RED 1.0 0.5 0.2 TS AlGaAs RED 0.1 0.05 0.02 0.01 0.1 0.2 0.5 1 2 5 10 20 30 50 IF – DC FORWARD CURRENT – mA RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 20 mA) RELATIVE LUMINOUS INTENSITY (NORMALIZED AT 20 mA) 5.0 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0 5 10 15 20 25 IDC – DC CURRENT PER LED – mA Figure 3. Relative Luminous Intensity vs. Forward Current. 30 7 HER, ORANGE, YELLOW, HIGH PERFORMANCE GREEN, EMERALD GREEN 1.3 DH As AlGaAs RED ηPEAK – RELATIVE EFFICIENCY (NORMALIZED AT 20 mA) RELATIVE EFFICIENCY (NORMALIZED AT 20 mA) 1.2 1.0 0.8 0.6 0.4 0.2 0 0 10 50 20 IPEAK – PEAK FORWARD CURRENT – mA EMERALD GREEN 1.1 HIGH EFFICIENCY RED/ORANGE 1.0 0.9 HIGH PERFORMANCE GREEN 0.8 0.7 0.6 0.5 0.4 200 300 100 YELLOW 1.2 0 10 20 30 40 50 60 70 80 90 IPEAK – PEAK FORWARD CURRENT – mA Figure 4. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current. HER, ORANGE, YELLOW, AND HIGH PERFORMANCE GREEN, EMERALD GREEN 40 DH As AlGaAs RED IF – FORWARD CURRENT – mA IF – FORWARD CURRENT – mA 40 35 30 25 RθJA = 559° C/W 20 RθJA = 689° C/W 15 10 5 0 30 20 40 60 80 RθJA = 470° C/W 25 RθJA = 300° C/W 20 YELLOW 15 10 RθJA = 705° C/W 5 0 0 HER, ORANGE, GREEN, EMERALD GREEN 35 100 0 20 40 60 80 100 TA – AMBIENT TEMPERATURE – °C TA – AMBIENT TEMPERATURE – °C NORMALIZED LUMINOUS INTENSITY Figure 5. Maximum Forward dc Current vs. Ambient Temperature. Derating Based on TjMAX = 110 °C 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 45 40 35 30 25 20 15 10 5 0 -5 -10 -15 -20 -25 -30 -35 -40 -45 ANGULAR DISPLACEMENT – DEGREES Figure 6. Relative Luminous Intensity vs. Angular Displacement. 15 Degree Family. NORMALIZED LUMINOUS INTENSITY 8 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 45 40 35 30 25 20 15 10 5 0 -5 -10 -15 -20 -25 -30 -35 -40 -45 ANGULAR DISPLACEMENT – DEGREES Figure 7. Relative Luminous Intensity vs. Angular Displacement. 25 Degree Family. Intensity Bin Limits Color Red/Orange Yellow Bin L M N O P Q R S T U V W X Y Z L M N O P Q R S T U V W Intensity Range (mcd) Min. Max. 101.5 162.4 162.4 234.6 234.6 340.0 340.0 540.0 540.0 850.0 850.0 1200.0 1200.0 1700.0 1700.0 2400.0 2400.0 3400.0 3400.0 4900.0 4900.0 7100.0 7100.0 10200.0 10200.0 14800.0 14800.0 21400.0 21400.0 30900.0 173.2 250.0 250.0 360.0 360.0 510.0 510.0 800.0 800.0 1250.0 1250.0 1800.0 1800.0 2900.0 2900.0 4700.0 4700.0 7200.0 7200.0 11700.0 11700.0 18000.0 18000.0 27000.0 9 Intensity Bin Limits, continued Color Green/ Emerald Green Bin E F G H I J K L M N O P Q R S T U V W Intensity Range (mcd) Min. Max. 7.6 12.0 12.0 19.1 19.1 30.7 30.7 49.1 49.1 78.5 78.5 125.7 125.7 201.1 201.1 289.0 289.0 417.0 417.0 680.0 680.0 1100.0 1100.0 1800.0 1800.0 2700.0 2700.0 4300.0 4300.0 6800.0 6800.0 10800.0 10800.0 16000.0 16000.0 25000.0 25000.0 40000.0 Maximum tolerance for each bin limit is ± 18%. Color Categories Color Green Yellow Orange Category # 6 5 4 3 2 1 3 2 4 5 1 2 3 4 5 6 7 8 Tolerance for each bin limit is ± 0.5 nm. Lambda (nm) Min. Max. 561.5 564.5 564.5 567.5 567.5 570.5 570.5 573.5 573.5 576.5 582.0 584.5 584.5 587.0 587.0 589.5 589.5 592.0 592.0 593.0 597.0 599.5 599.5 602.0 602.0 604.5 604.5 607.5 607.5 610.5 610.5 613.5 613.5 616.5 616.5 619.5 10 Mechanical Option Matrix Mechanical Option Code Definition 00 Bulk Packaging, minimum increment 500 pcs/bag 01 Tape & Reel, crimped leads, minimum increment 1300 pcs/bag 02 Tape & Reel, straight leads, minimum increment 1300 pcs/bag B2 Right Angle Housing, even leads, minimum increment 500 pcs/bag UQ Ammo Pack, horizontal leads, in 1K minimum increment Note: All categories are established for classification of products. Products may not be available in all categories. Please contact your local Agilent representative for further clarification/information. www.semiconductor.agilent.com Data subject to change. Copyright © 2001 Agilent Technologies, Inc. September 17, 2001 Obsoletes 5965-6165E 5988-2149EN