2.5 mm x 7.6 mm Rectangular LED Lamps Technical Data HLMP-R100 HLMP-0301 HLMP-0401 HLMP-0504 Features • Rectangular Light Emitting Surface • Flat High Sterance Emitting Surface • Stackable on 2.54 mm (0.100 inch) Centers • Ideal as Flush Mounted Panel Indicators • Ideal for Backlighting Legends • Long Life: Solid State Reliability • Choice of 4 Bright Colors DH AS AlGaAs Red High Efficiency Red Yellow High Performance Green • IC Compatible/Low Current Requirements Description The HLMP-R100, -0301, -0401, -0504 are solid state lamps encapsulated in a radial lead rectangular epoxy package. They utilize a tinted, diffused epoxy to provide high on-off contrast and a flat high intensity emitting surface. Borderless package design allows creation of uninterrupted light emitting areas. The HLMP-R100 uses a double heterojunction (DH) absorbing substrate (AS) aluminum gallium arsenide (AlGaAs) red LED chip in a light red epoxy package. This combination produces outstanding light output over a wide range of drive currents. The HLMP-0301 has a high efficiency red GaAsP on GaP LED chip in a light red epoxy package. The HLMP-0401 provides a yellow GaAsP on GaP LED chip in a yellow epoxy package. Package Dimensions The HLMP-0504 provides a green GaP LED chip in a green epoxy package. 2 Selection Guide Color DH AlGaAs Red Red Yellow Green Part Number HLMP-R100 HLMP-R100-FG0xx HLMP-0301 HLMP-0301-C00xx HLMP-0301-DECxx HLMP-0301-CD0xx HLMP-0401 HLMP-0401-B00xx HLMP-0401-D00xx HLMP-0401-CD0xx HLMP-0401-DEBxx HLMP-0504 HLMP-0504-B00xx HLMP-0504-DECxx HLMP-0504-CD0xx HLMP-0504-C00xx Luminous Intensity Iv (mcd) @ 20 mA Min. Typ. 2.1 – 5.4 17.2 2.1 – 1.3 – 2.1 6.8 1.3 4.2 3.6 – 1.4 – 3.6 – 2.2 7.2 3.6 11.4 2.6 – 1.6 – 4.2 13.4 2.6 8.4 2.6 – Part Numbering System HLMP - x x xx - x x x xx Mechanical Options 00: Bulk 01: Tape & Reel, Crimped Leads 02: Tape & Reel, Straight Leads DD: Ammo Pack, Straight Leads Color Bin Options 0: Full Color Bin Distribution B: Color Bins 2 & 3 only C: Color Bins 3 & 4 only Maximum Iv Bin Options 0: Open (No Maximum Limit) Others: Please refer to the Iv Bin Table Minimum Iv Bin Options Please refer to the Iv Bin Table Color Options 1. As AlGaAs Red 3. High Efficiency Red 4. Yellow 5. Green Package Options R,0: Rectangular 2.5 mm x 7.6 mm 3 Absolute Maximum Ratings at TA = 25°C HLMPR100 HLMP0301 HLMP0401 HLMP0504 Units Peak Forward Current 300 90 60 90 mA Average Forward Current[1] 20 25 20 25 mA DC Current[2] 30 30 20 30 mA Power Dissipation 87 135 85 135 mW Reverse Voltage (IR = 100 µA) 5 5 5 5 V 500 500 500 500 mA -55 to +100 -55 to +100 -20 to +100 °C Parameter Transient Forward Current[3] (10 µs Pulse) Operating Temperature Range Storage Temperature Range Lead Soldering Temperature (1.6 mm [0.063 in.] from body) -20 to +100 -55 to +100 -55 to +100 260°C for 5 seconds Notes: 1. See Figure 5 to establish pulsed operating conditions. 2. For AlGaAs Red, Red, and Green Series derate linearly from 50°C at 0.5 mA/°C. For Yellow Series derate linearly from 50°C at 0.2 mA/°C. 3. The transient peak current is the maximum non-recurring peak current that can be applied to the device without damaging the LED die and wirebond. It is not recommended that the device be operated at peak current beyond the peak forward current listed in the Absolute Maximum Ratings. 4 Electrical/Optical Characteristics at TA = 25°C HLMP-R100 Sym. Description 2θ1/2 Included Angle Between Half Luminous Intensity Points HLMP-0301 HLMP-0401 HLMP-0504 Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Units Test Conditions 100 100 100 100 Deg. Note 1. Fig. 6 λP Peak Wavelength 645 635 583 565 nm Measurement at Peak λd Dominant Wavelength 637 626 585 569 nm Note 2 Spectral Line Halfwidth 20 40 36 28 nm τs Speed of Response 30 90 90 500 ns C Capacitance 30 16 18 18 pF Thermal Resistance 260 260 260 260 °C/W VF Forward Voltage 1.8 VR Reverse Breakdown Voltage ηv Luminous Efficacy ∆λ1/2 RθJ-PIN 2.2 5.0 1.9 5.0 80 2.6 2.1 5.0 145 2.6 2.2 5.0 500 595 3.0 VF = 0; f = 1 MHz Junction to Cathode Lead V IF = 20 mA Figure 2. V IR = 100 µA lm/W Note 3 Notes: 1. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 2. The dominant wavelength, λd, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 3. Radiant intensity, Ie, in watts/steradian, may be found from the equation Ie = Iv/ηv, where Iv is the luminous intensity in candelas and ηv is the luminous efficacy in lumens/watt. Figure 1. Relative Intensity vs. Wavelength. 5 Figure 2. Forward Current vs. Forward Voltage. VF (300 mA) for AlGaAs Red = 2.6 Volts Typical. Figure 3. Relative Luminous Intensity vs. Forward Current. Figure 5. Maximum Tolerable Peak Current vs. Peak Duration (IPEAK MAX Determined from Temperature Derated I DC MAX). Figure 6. Relative Luminous Intensity vs. Angular Displacement. Figure 4. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current. ηv (300 mA) for AlGaAs Red = 0.7. 6 Intensity Bin Limits Color Red Bin C D E F G H I J K L M N O P Q R S T U V W X Y Z Intensity Range (mcd) Min. Max. 0.5 2.4 2.4 3.8 3.8 6.1 6.1 9.7 9.7 15.5 15.5 24.8 24.8 39.6 39.6 63.4 63.4 101.5 101.5 162.4 162.4 234.6 234.6 340.0 340.0 540.0 540.0 850.0 850.0 1200.0 1200.0 1700.0 1700.0 2400.0 2400.0 3400.0 3400.0 4900.0 4900.0 7100.0 7100.0 10200.0 10200.0 14800.0 14800.0 21400.0 21400.0 30900.0 7 Intensity Bin Limits, continued Color Yellow Green Bin B C D E F G H I J K L M N O P Q R S T U V W B C D E F G H I J K L M N O P Q R S T U V W Intensity Range (mcd) Min. Max. 1.6 2.5 2.5 4.0 4.0 6.5 6.5 10.3 10.3 16.6 16.6 26.5 26.5 42.3 42.3 67.7 67.7 108.2 108.2 173.2 173.2 250.0 250.0 360.0 360.0 510.0 510.0 800.0 800.0 1250.0 1250.0 1800.0 1800.0 2900.0 2900.0 4700.0 4700.0 7200.0 7200.0 11700.0 11700.0 18000.0 18000.0 27000.0 1.8 2.9 2.9 4.7 4.7 7.6 7.6 12.0 12.0 19.1 19.1 30.7 30.7 49.1 49.1 78.5 78.5 125.7 125.7 201.1 201.1 289.0 289.0 417.0 417.0 680.0 680.0 1100.0 1100.0 1800.0 1800.0 2700.0 2700.0 4300.0 4300.0 6800.0 6800.0 10800.0 10800.0 16000.0 16000.0 25000.0 25000.0 40000.0 Maximum tolerance for each bin limit is ± 18%. Color Categories Color Category # 6 5 4 3 2 1 3 2 4 5 Green Yellow Lambda (nm) Min. Max. 561.5 564.5 564.5 567.5 567.5 570.5 570.5 573.5 573.5 576.5 582.0 584.5 584.5 587.0 587.0 589.5 589.5 592.0 592.0 593.0 Tolerance for each bin limit is ± 0.5 nm. Mechanical Option Matrix Mechanical Option Code Definition 00 Bulk Packaging, minimum increment 500 pcs/bag 01 Tape & Reel, crimped leads, minimum increment 1300 pcs/bag 02 Tape & Reel, straight leads, minimum increment 1300 pcs/bag DD Ammo Pack, straight leads with minimum increment 2K/pack Note: All categories are established for classification of products. Products may not be available in all categories. Please contact your local Agilent representative for further clarification/information. www.semiconductor.agilent.com Data subject to change. Copyright © 2001 Agilent Technologies, Inc. August 15, 2001 Obsoletes 5968-4160E (3/99) 5988-2147EN