IRMS6400 TOP VIEW IRMT6400 SIDE VIEW 4 Mb/s Infrared Data Transceiver Dimensions in inches (mm) C .116 L .106 (2.95) (2.70) E D .157 (4.00) .190 (4.83) PIN 1 PIN 1 .138 (3.50) .374 (9.86) E=Emitter D=Detector IRMS6400 IRMS6400 IRMT6400 IRMT6400 Absolute Maximum Ratings, TA=25°C (except where noted) FEATURES • • • • • • • • • • • • Compliant with IrDA Specification Data Rates 9.6 Kb/s to 4.0 Mb/s Wide Range of Supply Voltage 2.6 to 5.5 V Standby Current 3.3 mA at 5.0 V Typical Shut Down Current 0.01 µA Typical Excellent Power Supply Noise Rejection Tri-State Receiver Output and TxD Disable AC Coupled Transmit Input – Provides Integrated Protection for Eye Safety High DC Ambient Rejection Independent LED Supply, Anode Pin Can Take – up to 9.0 V DC when not Transmitting and – up to 4.0 V above VCC when Transmitting Receiver Latency Less than 100 µs Slimline Package: H 4.0 mm x D 4.8 mm x L 9.8 mm ot r o f N DESCRIPTION With state of the art submicron BiCMOS circuitry, coupled with Infineon optoelectronic expertise, the IRMS6400/IRMT6400 outperforms its closest rival. Infineon has incorporated a mode selection pin that toggles the device to operate in FIR (4 Mb/s) or SIR/MIR (9.6 Kb/s to 1.152 Mb/s) mode. Its external Shut Down (SD) feature cuts current consumption to typically 0.01 µA. The transmit input is AC coupled, limiting transmit pulse duration to 70 µs, preventing transmitter damage and continuous LED output. Mode select determines the data rate. Low for 9.6 Kb/s to 1.152 Mb/s, high for 4 Mb/s. Supply Voltage Range, all states, VCC ................................... –0.5 to +7.0 V LED Anode Voltage, not transmitting, VLEDA........................................9.0 V LED Anode Voltage, transmitting, VLEDA .................................. 4.0 V + VCC Input Currents, (pin 3 and 5) .............................................................. 20 mA Output Sinking Current...................................................................... 50 mA Storage Temperature, TS .......................................................–40 to +100°C Ambient Temperature, operating, TA .......................................–25 to +85°C Lead Solder Temperature, 230°C ........................................................<10 s IC Junction Temperature, TJ ............................................................... 125°C Average IR LED Current, DC, ILED ................................................... 100 mA Repetitive Pulsed IR LED Current, <90 µs, ton <25%, ILED(RP) ............................................................ 700 mA Transmit Data Input Voltage, VTxD ..................................–0.5 to VCC + 0.5 V Receive Data Output Voltage, VRxD ....................................... –0.5 to VCC + 0.5 V n g si w e N e D Table 1. Pin Functions Pin no. Function Pin no. Function 1 LED Anode 5 SD/Mode 2 LED Cathode 6 VCC 3 TxD 7 *Do not connect 4 RxD 8 GND *Pin 7 internally grounded 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA www.infineon.com/opto • 1-888-Infineon (1-888-463-4636) 1 March 21, 2000-19 Figure 1. Block Diagram Bandwidth Control Preamp VCC VCC Tri-State CMOS Buffer Receive Detector Lowpass Filter Main AMP VCC Pin 6 RxD + Detector Reference Pin 4 Tri-state Control – + Receiver Output – Ambient DC Cancelling Receive Ouput Blanking AGC & Signal Reference Processor AGC SD/Mode Pin 5 LED Anode Pin 1 Transmit IR LED Switched Current Source TxD Input Buffer Power Down Control FIR/SIR-MIR Flip/Flop TxD Feedback Blanking Photodiode Regulated Voltage & Current Sources VCC TxD Pin 3 LED Cathode Pin 2 TxD In Error AMP GND Pin 8 Pull-down Electrical Characteristics Table 2. Basic Parameters, TA=25°C (except where noted) Parameter Min. Typ. Max. Unit Conditions Data Rate 9.6 K — 4M bits/s Standard pulse width VCC Voltage 2.6 — 5.5 V –25 to +85°C, VCC to VSS Maximum LED Anode Voltage — — 4 V+VCC V VCC=2.6 V to 5.5 V ICC Standby Current (Avg.) — 3.3 4.5 mA SD=0, VCC=2.6 V to 5.5 V, no receive signal ICC Receiving Current (Avg.) — 3.8 5.0 mA 10 µW, 4.0 Mb/s, 15 pF load ICC Shut Down Current (Note 1) (Avg.) — 0.01 1.0 µA SD=VCC, VCC=2.6 V to 5.5 V ICC Transmitting Current (Avg.) — 6 10 mA TxD=VCC, VCC=5.0 V, VLED=5.0 V, Ro=5.1 Ω Minimum VCC — 2.5 — V Reduced performance Parameter Min. Typ. Max. Unit Conditions TxD, SD Input Capacitance — 5.0 — pF VCC=2.6 V to 5.5 V TxD pull-down 350 500 700 kΩ TxD=VCC, VCC=5.0 V Minimum dV/dt of TxD Input Signal 0.7 1.4 — V/µs 5.0 V pulse TxD Minimum Hold Time for Mode Change 90 200 — ns VCC=2.6 V to 5.5 V, referenced to SD negative clocking edge TxD Minimum Setup Time for Mode Change (Note 2) –70 –40 — ns VCC=2.6 V to 5.5 V, referenced to SD negative clocking edge TxD Input Threshold 1.0 1.4 1.8 VCC VCC=2.6 V to 5.5 V, 125 ns input pulse SD Transmit Enable — Table 3. I/O Parameters 500 — ns VCC=2.6 V to 5.5 V, (Note 3) SD to TxD input disable & RxD tri-state — 50 70 ns VCC=2.6 V to 5.5 V SD Input Threshold 1.0 1.4 1.8 V VCC=5.0 V SD Input Threshold 0.6 0.9 1.2 V VCC=2.6 V 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA www.infineon.com/opto • 1-888-Infineon (1-888-463-4636) IRMS6400/IRMT6400 2 March 21, 2000-19 Table 3. I/O Parameters (continued) Parameter Min. Typ. Max. Unit Conditions RxD Output High 3.5 4.0 — V VCC=5.0 V, IOH=24 mA RxD Output High 2.0 2.3 — V VCC=2.7 V, IOH=6.0 mA RxD Output Low — 1.0 1.5 V VCC=5.0 V, IOL=24 mA RxD Output Low — 0.1 0.8 V VCC=5.0 V, IOL<1 mA RxD Output Low — 0.4 0.8 V VCC=2.7 V, IOL=6.0 mA RxD Short Circuit — 48 — mA VCC=5.0 V, RxD=0, RxD=VCC RxD Short Circuit — 48 — mA VCC=2.7 V, RxD=0, RxD=VCC RxD to VCC Tri-State Impedance RxD Rise/Fall Time 350 500 650 kΩ SD=VCC, VCC=5.0 V, measured between RxD to VCC — 7.0 — ns VCC=5.0 V, load=15 pF RxD Rise/Fall Time — 15 — ns VCC=5.0 V, load=100 pF RxD Rise/Fall Time — 10 — ns VCC=2.7 V, load=15 pF RxD Rise/Fall Time — 27 — ns VCC=2.7 V, load=100 pF Table 4. Receiver Parameters, High Rate Mode (FIR), TA=25°C (except where noted) Parameter Symbol Min. Typ. Max. Unit Data Rate — 4M — bit/s — Conditions 125 ns (low rate pulse), 0 to 70°C 2 Bit error rate=10–8 Logic High Input Irradiance EIHmin 10 — — µW/cm Logic High Input Irradiance EIHmax — — 500 mW/cm2 In-band irradiance maximum Minimum Detection Threshold EEmin — 4.0 — µW/cm2 2 4.0 Mb/s 0.4 µW/cm Ambient interference pulsed 500 800 µs 0 to 10 mW/cm2 ambient input — 50 100 µs 0 to 10 mW/cm2 ambient input — — 30 50 µs 0 to 10 mW/cm2 ambient input Pulse Width Correction Range — 90 — 175 ns 40 µW/cm2 input to produce 115 ns to 135 ns output, VCC=2.7 V to 5.5 V Pulse Width Settling — — 8.0 16 µs 40 µW/cm2 input Output Pulse Edge Jitter & Bias at RxD — — 10 — ns 125 ns, 40 µW/cm2 input, load=15 pf, measured at 1.4 V Output Pulse Width at RxD — 110 125 140 ns 125 ns, 40 µW/cm2 input, load=15 pf, measured at 1.4 V Power Supply Rejection <5 MHz — — 50 — mVP <0.1 pulse per second spurious output Power Supply Rejection >5 MHz — — 25 — mVP <0.1 pulse per second spurious output Logic Low Input Irradiance EIL — Receive Latency (Near-far) — — Powerup Latency — Transmit Latency (turn around) Table 5: Receiver Parameters, Low Rate Mode (SIR/MIR), TA=25°C (except where noted) Parameter Symbol Min. Typ. Max. Unit Conditions Data Rate — 9.6 K — 1.15 M bits/s 9.6 Kb/s to 115 Kb/s=1.63 µs, 576 Kb/s=434 ns, 1.152 Mb/s=217 ns Logic High Input Irradiance (MIR) EIHmin 10 — — µW/cm2 Bit error rate=10–8 Logic High Input Irradiance (SIR) EIHmin 4.0 — — µW/cm2 Bit error rate=10–8 Logic High Input Irradiance EIHmax — — 500 mW/cm2 In band irradiance maximum Logic Low Input Irradiance EIL — — 0.4 µW/cm2 Ambient interference pulsed Receive Latency (Near-far) — — 2.5 4.0 ms 0 to 10 mW/cm2 ambient input Transmit Latency (turn around) — — 50 100 µs 0 to 10 mW/cm2 ambient input Power-up Latency — — 50 150 µs 0 to 10 mW/cm2 ambient input Power Supply Rejection <5 MHz — — 50 — mVP <0.1 pulse per second spurious output Power Supply Rejection >5 MHz — — 25 — mVP <0.1 pulse per second spurious output 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA www.infineon.com/opto • 1-888-Infineon (1-888-463-4636) IRMS6400/IRMT6400 3 March 21, 2000-19 Table 5: Receiver Parameters, Low Rate Mode (SIR/MIR), TA=25°C (except where noted) (Continued) Output Pulse Width (1.15 MB) — 120 215 400 ns 217 ns pulse in Output Pulse Width at RxD (115 Kb/s) — 1.4 1.63 2.5 µs 1.63 ns pulse in Output Pulse Width at RxD (9.6 Kb/s) — 1.4 6 22 µs 19.5 µs pulse in Min. Typ. Max. Unit Conditions Table 6. Transmitter Output Parameter Transmit Delay — 15 — ns 125 ns pulse, VCC=5.0 V Pulse Width Limit 50 70 100 µs TxD pulse>100 µs, 5.0 V pulse, VCC=5.0 V TxD Peak Wavelength 850 870 900 nm IF=20 mA DC LED Anode Current Limit 510 610 680 mA TxD=VCC, LED anode=5.0 V, VCC=5.0 V, averaged over 125 ns pulse LED Anode Current Limit 310 450 550 mA TxD=VCC, LED anode=3.0 V, VCC=3.0 V, averaged over 125 ns pulse LED Cathode Saturation Drop — 0.3 0.4 V 400 mA, VCC=2.7 V VCC Transient Immunity VCC ±1 VCC ±2 — V peak 10 ns pulse height, VCC=5.0 V (Note 4) Transmit output rise and fall time (tr, tf) 10 — 40 ns VLED=2.7 V, no resistor Radiant Intensity (peak, 4 Mb/s mode) 170 400 mW/sr VLED=2.7 V, no resistor 100 Note 1: For Shut Down (SD) current to fall below 1 µA requires driving the Shut Down (SD) pin to within 0.5 V of VCC to ensure cutoff of the input PMOS transistor of the input CMOS totem pole. Note 2: Negative setup times indicate that the internal data propagation time is longer than the latching signal propagation time. This is common on logic devices. It means that the TxD data can go away before the negative Shut Down (SD) edge occurs and not lose the data. (See application notes for more details). Note 3: Shut Down (SD) to transmit enable is the time required for the transmit bias circuits to stabilize. Applying a transmit pulse before this time has elapsed will reduce the transmit pulse width. Note 4: Transmit VCC Transient Immunity measures the transmitter circuitry immunity from large VCC and ground return inductive transients arising from the action of large transmitter di/dt currents on VCC and ground return trace inductances. This test applies a negative 10 ns VCC pulse to simulate the effects of transmitter current induce VCC transients (assuming the LED anode supply and VCC have a shared inductance) and measures for less than a 10% change in pulse width or delivered charge on the initial pulse and subsequent pulse. Mode Switching (see Figure 2.) Figure 2. Switching Mode Normally the IRMS6400/IRMT6400 Series initializes in the SIR/ MIR (9.6 Kb/s to 1.152 Mb/s) mode upon power-up. Switching the module to FIR (4 Mb/s) Mode can be achieved as follows: tS SD/Mode • Bring Shut Down (SD)/Mode pin to a logic “High” status. • Bring TxD input to a logic “High” status. Wait for ts ≥–40 ns. • Bring Shut Down (SD)/Mode pin to a logic “Low” status. The negative transition of this pulse will set the module mode to (4 Mb/s) data rate by reading the state of TxD. Bring TxD to a logic “Low” after waiting for th ≥90 ns. th TxD pulse will set the device into 4 Mb/s data rate mode TxD Pulse will set the device into SIR/MIR mode Switching to SIR/MIR (9.6 Kb/s to 1.15 Mb/s) Mode: • Bring Shut Down (SD)/Mode pin to a logic “High” status. • Bring TxD input to a logic “Low” status. Wait for ts ≥–40 ns. • Bring Shut Down (SD)/Mode pin to a logic “Low” status. The negative transition of this pulse will set the module mode to 115 Kb/s data rate by reading the state of TxD. 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA www.infineon.com/opto • 1-888-Infineon (1-888-463-4636) IRMS6400/IRMT6400 4 March 21, 2000-19 Figure 3. Shutdown Current vs. Ambient Temperature Figure 6. RxD Pulse Width vs. Ambient Temperature 1.1 0.7 Pulse Width (r.u.) Shutdown Current (µΑ) 1.05 0.6 0.5 0.4 0.3 0.2 V =V SD 4Mbps mode. O Typical value at 25 C is 126ns. 0.95 0.9 =2.7V. LED O 0.85 Typical value at 25 C is 30nA. 0.1 1 0 0.8 -40 -20 0 20 40 60 80 100 -40 -20 0 O 40 60 80 100 O Ambient Temperature ( C) Ambient Temperature ( C) Figure 7. RxD Pulse Rise and Fall Time vs. Temperature Figure 4. Standby Current vs. Temperature 16 4 3.5 2.7V 3.0V 3.3V 4.0V 5.0V 12 Fall Time 10-90% Time (ns) 3 Rise Time 14 V CC Standby Current (mA) 20 2.5 10 8 4Mbps data rate. VCC=2.7V 6 4 2 2 0 1.5 -40 -20 0 20 40 60 80 -40 100 -20 0 O 60 80 800 1.05 700 1 115Kbps mode. Typical value at 25OC is 1.63us. 0.9 0.85 600 500 R LED 400 0Ω 1.06Ω 1.80Ω 2.77Ω 3.99Ω 5.17Ω 300 0.8 -40 -20 0 20 40 60 100 Figure 8. LED Peak Current vs. VLED 1.1 Peak LED Current (mA) Pulse Width (r.u.) 40 Ambient Temperature ( C) Figure 5. RxD Pulse Width vs. Ambient Temperature 0.95 20 O Ambient Temperature ( C) 80 200 100 2.5 Ambient Temperature ( OC) 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA www.infineon.com/opto • 1-888-Infineon (1-888-463-4636) 3 3.5 4 V LED 4.5 5 5.5 (V) IRMS6400/IRMT6400 5 March 21, 2000-19 Figure 9. LED Current vs. Ambient Temperature Figure 12. IR Intensity vs. Ambient Temperature 1.2 1.2 1 1 4Mbps mode, V =2.7V. LED IR Intensity (r.u.) LED Current (r.u.) O Typical peak current at 25 C is450mA. 0.8 0.6 0.4 0.2 0.8 4Mbps mode, VLED=2.7V. O Typical peak intensity at 25 C is 200mW/sr. 0.6 0.4 0.2 0 0 -40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100 O O Ambient Temperature ( C) Ambient Temperature ( C) Figure 13. LED Intensity vs. VLED Figure 10. Peak Intensity vs. LED peak Current 400 240 220 300 Intensity (mW/sr) On-Axis LED Peak Intensity (mW/sr) 260 200 200 RLED 180 0Ω 1.06Ω 1.80Ω 2.77Ω 3.99Ω 5.17Ω 160 140 100 120 300 400 500 I LED 600 700 2.5 3 3.5 (mA) 4 V Figure 11. LED Intensity vs RLED LED 4.5 5 5.5 (V) Figure 14. Farfield Receiver Sensitivity Pattern (FIR) 18 260 16 240 Horizontal Vertical 14 Intensity (mW/sr) 2 Sensitivity (uW/cm ) 220 200 V 180 LED 2.7V 3.0V 3.3V 3.5V 4.0V 4.5V 5.0V 5.5V 160 140 12 10 8 6 4 2 120 0 1 2 R LED 3 (Ohm) 4 -45 5 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA www.infineon.com/opto • 1-888-Infineon (1-888-463-4636) -30 -15 0 15 30 45 Angle (Degrees) IRMS6400/IRMT6400 6 March 21, 2000-19 Figure 15. Reciever Sensitivity vs. Temperature (115 Kb/s) Figure 18. RxD Pulse Rise and Fall Time vs. Temperature 1.4 1.3 TR 1.2 1.2 V CC=3.3V TF 1.1 V CC=5.5V T R and TF (r.u.) Receiver Sensivity (r.u.) VCC=2.7V 1 1 4Mbps data rate. VCC=2.7V. Typical value at 25O C is 20ns. 0.9 0.8 2 115Kbps data rate. Typical value at 25OC & VCC=2.7V is 2.0 uW/cm 0.8 0.6 0.7 -40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100 O O Ambient Temperature ( C) Ambient Temperature ( C) Figure 16. Receiver Sensitivity vs. Temperature 2.5 Receiver Sensivity (r.u.) 2 V 1.5 V CC CC =2.7V =3.3V V CC=5.5V 1 4Mbps data rate. Typical value at 25O C & VCC=2.7V is 5.0 uW/cm 2 0.5 0 -40 -20 0 20 40 60 80 100 O Ambient Temperature ( C) Figure 17. Infrared Reflow Soldering Profile 300 Maximum 240(+5/–0) °C Temperature (°C) 250 210°C 200 150 30 s minimum 30 s maximum 100 50 60 s minimum 0 0 50 Note: Peak temperature is 240 (+5 –0)°C for less than 10 seconds. 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA www.infineon.com/opto • 1-888-Infineon (1-888-463-4636) 100 150 Time (sec) IRMS6400/IRMT6400 7 March 21, 2000-19 Interface Diagrams Figure 19. Super I/O (PC87338VLJ) to IRMS6400/ IRMT6400 VCC Figure 21. Super I/O (PC87338VLJ) to IRMS6400/IRMT6400 with independent VLED power supply VLED VCC 0.1 µF 22 µF R0 R0 1 6 LED VCC Anode 50 VCC IR TxD 3 65 50 VCC IR TxD 65 TxD IRMX6400 C4=22 µF C3=0.1 µF 1 6 VCC LED Anode C1=0.1 µF C2=10 µF 3 TxD IRMX6400 PC87338VLJ PC87338VLJ IR RxD GND IR SLO VSS 42 4 67 IR RxD RxD SD GND 5 8 68 GND Figure 20. Ultra I/O controller with fast IR (FDC37C93xFR) to IRMS6400/IRMT6400 VCC 0.1 µF 22 µF R0 1 6 LED VCC Anode 125 VCC VSS 42 IR TxD 99 3 TxD IR RxD GND GND IR MODE 130 98 19 4 IR SLO 68 4 RxD SD 5 GND 8 Table 7. Recommended RO values for different VLED Parameter Values Unit VLED power supply 2.4 2.7 3.0 3.5 4.0 4.5 5.0 V Resistor 0 0 1.2 2.7 3.9 5.1 Ω 0 Table 8. Slimline IRMS64XX Truth Table Inputs Outputs SD VCC TxD Detector RxD LED High 2.4 to 5.5 V X=don’t care state X=don’t care state 500 kΩ pull-up Off Low 2.4 to 5.5 V High Undefined On High Off Low Off IRMX6400 FDC37C93XFR 67 RxD 2.4 to 5.5 V SD GND 5 8 2.4 to 5.5 V <0.4 µW/cm (115 Kb/s) <1.0 µW/cm2 (1 & 4 Mb/s) 2.4 to 5.5 V 2.4 to 5.5 V 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA www.infineon.com/opto • 1-888-Infineon (1-888-463-4636) Low 2 Low <4.0 µW/cm2 (115 Kb/s) <10.0 µW/cm2 (1 & 4 Mb/s) IRMS6400/IRMT6400 8 March 21, 2000-19 Ordering Information Figure 23. Reel Dimensions in Inches (mm) Part Number Description PCB Mounting Orientation IRMS6400 Integrated Packaged in Transceiver Component Carrier —Side View Reel (1000/reel) for Side View Mounting on PCB Integrated Transceiver —Top View Packaged in Component Carrier Reel (1000/reel) for Top View Mounting on PCB 0.512+0.020 0.79 – 0 .0 0 8 (20.2) Min. 13.0 +0.5 – 0.2 X IRMT6400 Matte finish these areas 12.97 (330.0) Ref. 4.01 (102.0) Ref. 0.079±0.020 (2.0 ± 0.5) Detail A Tape Leader and Trailer is 400 mm minimum. W1 (Measured at hub) W2 (Measured at hub) See detail A 16.4 mm(+2 mm/-0 mm) 22.4 mm (Max) Figure 22. Tape Dimensions in Inches (mm) .315±.004 (8.00±.10) .059+.004 (1.50+.10) .079±.004 (2.00±.10) .157±.004 (4.00±0.10) .069±.004 (1.75±.010) 4° Max. .295±.004 (7.50±0.10) .401±.004 Bo (10.19±.10) .630 +.012 –. 0 0 4 16.0 +.30 –.10 Pin 1 IRMT6400 (top view) 1.50+.25 (.059+.010) .199±.004 (5.06 .10) Ko .0140±.0005 (.356±.013) Feed direction 8° Max. .167±.004 (4.23±.10) .315±.004 (8.00±.10) .059+.004 (1.50+.10) Ao .079±.004 (2.00±.10) .157±.004 (4.00±0.10) .069±.004 (1.75±.010) .295±.004 (7.50±0.10) .630 +.012 –. 0 0 4 16.0 +.30 –.10 4° Max. .216 (5.48) .400±.004 Bo (10.16±.10) Pin 1 IRMS6400 (side view) 1.50+.25 (.059+.010) .156 (3.97) Feed direction 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA www.infineon.com/opto • 1-888-Infineon (1-888-463-4636) .0130±.0005 (.330±.013) .167±.004 (4.23 .10) Ko 8° Max. .185±.004 Ao (4.70±.10) IRMS6400/IRMT6400 9 March 21, 2000-19 Figure 24. IRMS6400/IRMT6400 detail drawings with optional side view or top view mounting Dimensions in inches (mm)—All dimensions have tolerances of ±0.004” (±0.1 mm) .197 (5.00) .333 (7.71) 1 2 3 4 5 6 7 8 1" Draft pick and place .165 (4.20) .079 (2.00) .053 (1.35) .167 .051 (4.23) (1.30) .004 (.10) .028 (.70) Typ. .190 (4.83) .039 (1.00) Typ. Recommended PCB footprint TOP VIEW .065 (1.65) .134 (3.40) .67 (1.70) Front pick and place CL E D .079 (2.00) .012 (.28) 5° 4X 5° 4X .069 (1.74) .157 (4.00) .051 (1.30) Pin 1 .030 (0.75) .008 (.20) 90° to 93° Coplaner .0059 (0.15) .053 (1.35) .016 (0.40) Typ. .116 (2.95) .106 (2.70) CL .014 (.36) .388 (9.86) Max. Pin 1 1° Draft (2 Plcs) .027 (0.69) .020 .039 (0.51) (1.00) 6400RYYWW 5° 4X .138 (3.50) .378 (9.60) For high EMI environment application the IRMS6400 and IRMT6400 modules are available with a metal can shield. The metal shielded modules are designated as IRMS6409 and IRMT6409 respectively. © Infineon Technologies, Corp., Optoelectronic Division (formerly Siemens Microelectronics, Inc.) Printed in the United States of America. All rights reserved. The information provided is believed to be accurate and reliable. Infineon reserves the right to make changes to the product described without notice. No liability is assumed as a result of its use nor for any infringement of the rights of others. This document may contain preliminary information and is subject to change by Infineon without notice. Some of the parametric data expressed in this preliminary data sheet is considered to be functional by design. Infineon assumes no responsibility or liability for any use of the information contained herein. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Infineon or third parties. The products described in this document are not intended for use in implantation or other direct life support applications where malfunction may result in the direct physical harm or injury to persons. NO WARRANTIES OF ANY KIND, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE, ARE OFFERED IN THIS DOCUMENT. 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA www.infineon.com/opto • 1-888-Infineon (1-888-463-4636) IRMS6400/IRMT6400 10 March 21, 2000-19