ETC UCC28C43DR

 SLUS458B – AUGUST 2001
FEATURES
D
D
D
D
D
D
D
D
D
DESCRIPTION
1-MHz Operation
50-µA Start-Up Current, 100-µA Maximum
Low Operating Current of 2.3 mA at 52 kHz
50-ns Cycle-by-Cycle Overcurrent Limiting
±1-A Peak Output Current
Rail-to-Rail Output Swings with 25-ns Rise
and 20-ns Fall Times
±1% Initial Trimmed 2.5-V Error Amplifier
Reference
Trimmed Oscillator Discharge Current
MSOP-8 Package Minimizes Board Space
UCC38C4x family is a high-performance currentmode PWM controller. It is an enhanced BiCMOS
version with pin-for-pin compatibility to the
industry standard UC384xA family and UC384x
family of PWM controllers. In addition, lower
startup voltage versions of 7 V are offered as
UCC38C40 and UCC38C41.
Providing necessary features to control fixed
frequency, peak current-mode power supplies,
this family offers the following performance
advantages. The device offers high-frequency
operation up to 1 MHz with low start-up and
operating currents, thus minimizing start-up loss
and low operating power consumption for
improved efficiency. The device also features a
very fast current-sense-to-output delay time of
50 ns and a ±1 A peak output current capability
with improved rise and fall times for driving large
external MOSFETs directly.
APPLICATIONS
D Switch-Mode Power Supplies
D dc-to-dc Converters
D Board Mount Power Modules
The UCC38C4x family is offered in 8-pin
packages, MSOP (DGK), SOIC (D) and PDIP (P).
FUNCTIONAL BLOCK DIAGRAM
VREF
UVLO
+
7
VDD
5
GND
6
OUT
+
5.0 V
VREF 8
VREF
GOOD LOGIC
RT/CT 4
OSC
(NOTE)
2.5 V
FB
+
ERROR AMP
T
2R
S Q
2
R
1V
COMP 1
CS
R Q
3
Note: Toggle flip–flop used only in UCC38C41, UCC38C44, and UCC38C45.
UDG–99139
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2001, Texas Instruments Incorporated
!" # $%&" !# '%()$!" *!"&+
*%$"# $ " #'&$$!"# '& ",& "& # &-!# #"% &"#
#"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*&
"&#"0 !)) '!! &"&#+
www.ti.com
1
SLUS458B – AUGUST 2001
recommended operating conditions
MIN
MAX
UNIT
Input voltage, VDD
18
Output voltage range, VOUT
18
V
200
mA
–20
mA
150
°C
Average output current, IOUTW
Reference output current, IOUT(ref)W
Operating junction temperature, TJW
–55
V
¶ It is not recommended that the device operate under conditions beyond those specified in this table for extended periods of time.
absolute maximum ratings over operating free-air temperature (unless otherwise noted)}w
Supply voltage (VDD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V
Output current, IOUT peak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±1 A
Output energy, capacitive load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 µJ
Voltage rating (COMP, CS, FB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 6.3 V
(OUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 20 V
(RT/CT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 6.3 V
(VREF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Error amplifier output sink current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 mA
Total Power Dissipation at TA = 25°C: D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650 mW
DGK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 850 mW
P package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 mW
Operating junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to 150°C
Storage temperature range Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Lead Temperature (Soldering, 10 seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
‡ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
§ All voltages are with respect to ground. Currents are positive into and negative out of the specified terminals. Consult the Packaging Section of
the Databook for thermal limitations and considerations of the package.
AVAILABLE OPTIONS
TA
MAXIMUM
DUTY CYCLE
100%
–40°C
40°C to 85°C
50%
100%
0°C
0
C to 70°C
70 C
50%
UVLO
ON/OFF
SOIC–8
SMALL OUTLINE
(D)
PDIP–8
PLASTIC DIP
(P)
MSOP–8
SMALL OUTLINE
(DGK)
14.5V / 9.0V
UCC28C42D
UCC28C42P
UCC28C42DGK
8.4V / 7.6V
UCC28C43D
UCC28C43P
UCC28C43DGK
7.0V / 6.6V
UCC28C40D
UCC28C40P
UCC28C40DGK
14.5V / 9.0V
UCC28C44D
UCC28C44P
UCC28C44DGK
8.4V / 7.6V
UCC28C45D
UCC28C45P
UCC28C45DGK
7.0V / 6.6V
UCC28C41D
UCC28C41P
UCC28C41DGK
14.5V / 9.0V
UCC38C42D
UCC38C42P
UCC38C42DGK
8.4V / 7.6V
UCC38C43D
UCC38C43P
UCC38C43DGK
7.0V / 6.6V
UCC38C40D
UCC38C40P
UCC38C40DGK
14.5V / 9.0V
UCC38C44D
UCC38C44P
UCC38C44DGK
8.4V / 7.6V
UCC38C45D
UCC38C45P
UCC38C45DGK
7.0V / 6.6V
UCC38C41D
UCC38C41P
UCC38C41DGK
† D (SOIC–8) and DGK (MSOP–8) packages are available taped and reeled. Add R suffix to device type (e.g.
UCC28C42DR) to order quantities of 2500 devices per reel. Tube quantities are 75 for D packages (SOIC–8) and
80 for DGK package (MSOP–8), and 50 for P package (PDIP-8).
2
www.ti.com
SLUS458B – AUGUST 2001
electrical characteristics VDD = 15 V (See Note 1), RT = 10 kΩ, CT = 3.3 nF, CVDD = 0.1µF and no load
on the outputs, TA = –40°C to 85°C for the UCC28C4x and TA = 0°C to 70°C for the UCC38C4x,
TA = TJ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Reference Section
Output voltage, initial accuracy
Line regulation
TA = 25°C
IOUT = 1mA
VDD = 12 V to 18 V
Load regulation
1mA to 20mA
Temperature stability
See Note 2
Total output variation
See Note 2
Output noise voltage
10 Hz to 10 kHz,
Long term stability
1000 hours,
4.9
5.0
5.1
V
2
20
mV
1
25
mV
0.4
mV/°C
0.2
4.82
TA = 25°C,
TA = 125°C,
See Note 2
–30
V
µV
50
See Note 2
Output short circuit
5.18
5
25
mV
–45
–55
mA
52
55
kHz
0.2%
1.0%
Oscillator Section
Initial accuracy
Voltage stability
Temperature stability
Amplitude
Discharge current
TA = 25°C,
See Note 3
VDD = 12 V to 18 V
49
TMIN to TMAX,
See Note 2
RT/CT Pin peak-to-peak
TA = 25°C,
RT/CT = 2 V,
RT/CT = 2 V,
5
%
1.9
See Note 4
See Note 4
V
7.7
8.4
9.0
mA
7.2
8.4
9.5
mA
2.475
2.500
2.525
2.45
2.50
2.55
V
–0.1
–2.0
µA
Error Amplifier Section
Feedback input voltage, initial accuracy
Feedback input voltage, total variation
Input bias current
VCOMP = 2.5 V,
VCOMP = 2.5 V,
TA = 25°C
V
Open-loop voltage gain (AVOL)
VFB = 5.0 V
VOUT = 2 V to 4 V
65
90
dB
Unity gain bandwidth
See Note 2
1.0
1.5
MHz
Power supply rejection ratio (PSRR)
VDD = 12 V to 18 V
VFB = 2.7 V,
VCOMP = 1.1 V
60
2
14
mA
–0.5
–1.0
mA
5
6.8
Output sink current
Output source current
High-level output voltage (VOH)
VFB = 2.3 V,
VFB = 2.7 V,
VCOMP = 5V
RLOAD = 15 k to GND
Low-level output voltage (VOL)
VFB = 2.7 V,
RLOAD = 15 k to VREF
dB
V
0.1
1.1
V
2.85
3.00
3.15
V/V
0.9
1.0
1.1
V
–0.1
–2.0
µA
35
70
ns
Current Sense Section
Gain
See Note 5, 6
Maximum input signal
VCOMP = 2 V
VDD = 12 V to 18 V, See Note 2, 5
Power supply rejection ratio (PSRR)
Input bias current
CS to output delay
COMP to CS offset
70
VCS = 0 V
1.15
Adjust VDD above the start threshold before setting at 15 V.
Ensured by design. Not production tested.
Output frequencies of the UCC38C41, UCC38C44 and the UCC38C45 are half the oscillator frequency.
Oscillator discharge current is measured with RT = 10 kΩ to VREF.
Parameter measured at trip point of latch with VFB = 0 V.
DV
COM , 0V ¬ V
¬ 900mV
NOTE: 6. Gain is defined as ACS +
CS
DV
CS
NOTE:
NOTE:
NOTE:
NOTE:
NOTE:
dB
V
1.
2.
3.
4.
5.
www.ti.com
3
SLUS458B – AUGUST 2001
electrical characteristics VDD = 15 V (See Note 1), RT = 10 kΩ, CT = 3.3 nF, CVDD = 0.1µF and no load
on the outputs, TA = –40°C to 85°C for the UCC28C4x and TA = 0°C to 70°C for the UCC38C4x,
TA = TJ (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Output Section
VOUT low (RDS(on) Low)
VOUThigh (RDS(on) High)
ISINK = 200 mA
ISOURCE = 200 mA
5.5
15
10
25
Rise tIme
TA = 25°C,
TA = 25°C,
CLOAD = 1 nF
25
50
CLOAD = 1 nF
20
40
Fall time
Ω
ns
Undervoltage Lockout Section
Start threshold
Minimum o
operating
erating voltage
UCC38C42, UCC38C44
13.5
14.5
15.5
UCC38C43, UCC38C45
7.8
8.4
9.0
UCC38C40, UCC38C41
6.5
7.0
7.5
UCC38C42, UCC38C44
8
9
10
UCC38C43, UCC38C45
7.0
7.6
8.2
UCC38C40, UCC38C41
6.1
6.6
7.1
UCC38C42, UCC38C43, UCC38C40
94%
96%
UCC38C44, UCC38C45, UCC38C41
47%
48%
V
PWM Section
Ma im m duty
Maximum
d t cycle
c cle
Minimum duty cycle
VFB < 2 V
0%
Current Supply Section
Start-up current (ISTART-UP)
VDD < Undervoltage lockout start threshold
VFB = VCS = 0 V
Operating supply current (IDD)
NOTE 1:
100
µA
2.3
3.0
mA
Adjust VDD above the start threshold before setting at 15 V.
PDIP (P) PACKAGE
(TOP VIEW)
COMP
FB
CS
RT/CT
4
50
1
8
2
7
3
4
6
5
SOIC (D) OR MSOP (DGK) PACKAGE
(TOP VIEW)
COMP
FB
CS
RT/CT
VREF
VDD
OUT
GND
www.ti.com
1
8
2
7
3
6
4
5
VREF
VDD
OUT
GND
SLUS458B – AUGUST 2001
pin assignments
COMP: This pin provides the output of the error amplifier for compensation. In addition, the COMP pin is
frequently used as a control port by utilizing a secondary-side error amplifier to send an error signal across the
secondary-primary isolation boundary through an opto-isolator.
CS: The current sense pin is the non-inverting input to the PWM comparator. This is compared to a signal
proportional to the error amplifier output voltage. A voltage ramp can be applied to this pin to run the device with
a voltage mode control configuration.
FB: This pin is the inverting input to the error amplifier. The non-inverting input to the error amplifier is internally
trimmed to 2.5 V ±1%.
GND: Ground return pin for the output driver stage and the logic level controller section.
OUT: The output of the on-chip drive stage. OUT is intended to directly drive a MOSFET. The OUT pin in the
UCC38C40, UCC38C42 and UCC38C43 is the same frequency as the oscillator, and can operate near 100%
duty cycle. In the UCC38C41, UCC38C44 and the UCC38C45, the frequency of OUT is one-half that of the
oscillator due to an internal T flipflop. This limits the maximum duty cycle to < 50%.
RT/CT: Timing resistor and timing capacitor. The timing capacitor should be connected to the device ground
using minimal trace length.
VDD: Power supply pin for the device. This pin should be bypassed with a 0.1-µF capacitor with minimal trace
lengths. Additional capacitance may be needed to provide hold up power to the device during startup.
VREF: 5-V reference. For stability, the reference should be bypassed with a 0.1-µF capacitor to ground using
the minimal trace length possible.
www.ti.com
5
SLUS458B – AUGUST 2001
APPLICATION INFORMATION
This device is a pin-for-pin replacement of the bipolar UC3842 family of controllers, the industry standard PWM
controller for single-ended converters. Familiarity with this controller family is assumed.
The UCC28C4x/UCC38C4x series is an enhanced replacement with pin-to-pin compatibility to the bipolar
UC284x/UC384x and UC284xA/UC384xA families. The new series offers improved performance when
compared to older bipolar devices and other competitive BiCMOS devices with similar functionality. Note that
these improvements discussed below generally consist of tighter specification limits that are a subset of the
older product ratings, maintaining drop-in capability. In new designs these improvements can be utilized to
reduce the component count or enhance circuit performance when compared to the previously available
devices.
advantages
This device increases the total circuit efficiency whether operating off-line or in dc input circuits. In off-line
applications the low start-up current of this device reduces steady state power dissipation in the startup resistor,
and the low operating current maximizes efficiency while running. The low running current also provides an
efficiency boost in battery operated supplies.
low voltage operation
Two members of the UCC38C4x family are intended for applications that require a lower start-up voltage than
the original family members. The UCC38C40 and UCC38C41 have a turn-on voltage of 7.0 V typical and exhibit
hysteresis of 0.4 V for a turn-off voltage of 6.6 V. This reduced start-up voltage enables use in systems with lower
voltages, such as 12-V battery systems which are nearly discharged.
high speed operation
The BiCMOS design allows operation at high frequencies that were not feasible in the predecessor bipolar
devices. First, the output stage has been redesigned to drive the external power switch in approximately half
the time of the earlier devices. Second, the internal oscillator is more robust with less variation as frequency
increases. In addition, the current sense to output delay has been reduced by a factor of three, to 45ns typical.
These features combine to provide a device capable of reliable high frequency operation.
The UCC38C4x family oscillator is true to the curves of the original bipolar devices at lower frequencies yet
extends the frequency programmability range to at least 1MHz. This allows the device to offer pin to pin
capability where required yet capable of extending the operational range to the higher frequencies typical of
latest applications. When the original UC3842 was released in 1984 most switching supplies operated between
20kHz and 100kHz. Today, the UCC38C4x can be used in designs cover a span roughly ten times higher than
those numbers.
start/run current improvements
The start–up current is only 60 µA typical, a significant reduction from the bipolar device’s ratings of 300uA
(UC384xA). For operation over the temperature range of –40 to 85°C the UCC28C4x devices offer a maximum
startup current of 100 µA, an improvement over competitive BiCMOS devices. This allows the power supply
designer to further optimize the selection of the startup resistor value to provide a more efficient design. In
applications where low component cost overrides maximum efficiency the low run current of 2.3 mA, typical,
may allow the control device to run directly through the single resistor to (+) rail, rather than needing a bootstrap
winding on the power transformer, along with a rectifier. The start/run resistor for this case must also pass
enough current to allow driving the primary switching MOSFET, which may be a few milliamps in small devices.
6
www.ti.com
SLUS458B – AUGUST 2001
APPLICATION INFORMATION
± 1% initial reference voltage
The BiCMOS internal reference of 2.5 V has an enhanced design and utilizes production trim to allow initial
accuracy of ±1% at room temperature and ± 2% over the full temperature range. This can be used to eliminate
an external reference in applications that do not require the extreme accuracy afforded by the additional device.
This is very useful for nonisolated dc-to-dc applications where the control device is referenced to the same
common as the output. It is also applicable in offline designs that regulate on the primary side of the isolation
boundary by looking at a primary bias winding, or perhaps from a winding on the output inductor of a
buck-derived circuit.
reduced discharge current variation
The original UC3842 oscillator did not have trimmed discharged current, and the parameter was not specified
on the datasheet. Since many customers attempted to use the discharge current to set a crude deadtime limit
the UC3842A family was released with a trimmed discharge current specified at 25°C. The
UCC28C4x/UCC38C4x series now offers even tighter control of this parameter, with approximately ±3%
accuracy at 25°C, and less than 10% variation over temperature using the UCC28C4x devices. This level of
accuracy can enable a meaningful limit to be programmed, a feature not currently seen in competitive BiCMOS
devices. The improved oscillator and reference also contribute to decreased variation in the peak to peak
variation in the oscillator waveform, which is often used as the basis for slope compensation for the complete
power system.
soft-start
The following diagram provides a typical soft-start circuit for use with the UCC38C42. The values of R and C
should be selected to bring the COMP pin up at a controlled rate, limiting the peak current supplied by the power
stage. After the soft-start interval is complete the capacitor continues to charge to VREF, effectively removing
the PNP transistor from circuit considerations.
The optional diode in parallel with the resistor forces a soft-start each time the PWM goes through UVLO and
the reference (VREF) goes low. Without the diode,the capacitor otherwise remains charged during a brief loss
of supply or brown-out, and no soft-start is enabled upon reapplication of VIN.
VREF 8
UCC38C42
COMP
1
GND
5
Figure 1
www.ti.com
UDG–01072
7
SLUS458B – AUGUST 2001
APPLICATION INFORMATION
oscillator synchronization
The UCC38C4x oscillator has the same synchronization characteristics as the original bipolar devices. Thus,
the information in the Application Note U–100A, UC3842/3/4/5 Provides Low-Cost Current-Mode Control, (TI
Literature No. SLUA143) still applies. The application note describes how a small resistor from the timing
capacitor-to-ground can offer an insertion point for synchronization to an external clock, (see Figures 2 and 3).
Figure 2 shows how the UCC38C42 can be synchronized to an external clock source. This allows precise
control of frequency and dead time with a digital pulse train.
8
VREF
4
RT / CT
RT
SYNCHRONIZATION
CIRCUIT INPUT
CT
UCC38C42
PWM
24
UDG–01069
Figure 2. Oscillator Synchronization Circuit
CLOCK
INPUT
PWM
OUT
UPPER THRESHOLD
LOW
HIGH
LOW
LOWER THRESHOLD
ON .
OFF .
ON .
VCT (ANALOG)
OUTPUT A
UPPER THRESHOLD
VCT
LOWER THRESHOLD
VSYNC (DIGITAL)
COMBINED
Figure 3. Synchronization to an External Clock
8
www.ti.com
UDG–01070
SLUS458B – AUGUST 2001
APPLICATION INFORMATION
precautions
The absolute maximum supply voltage is 20 V, including any transients that may be present. If this voltage is
exceeded, device damage is likely. This is in contrast to the predecessor bipolar devices, which could survive
up to 30 V. Thus, the supply pin should be decoupled as close to the ground pin as possible. Also, since no clamp
is included in the device, the supply pin should be protected from external sources which could exceed the 20 V
level.
Careful layout of the printed board has always been a necessity for high frequency power supplies. As the device
switching speeds and operating frequencies increase the layout of the converter becomes increasingly
important.
This 8-pin device has only a single ground for the logic and power connections. This forces the gate drive current
pulses to flow through the same ground that the control circuit uses for reference. Thus, the interconnect
inductance should be minimized as much as possible. One implication is to place the device (gate driver)
circuitry close to the MOSFET it is driving. Note that this can conflict with the need for the error amplifier and
the feedback path to be away from the noise generating components.
circuit applications
Figure 4 shows a typical off-line application.
D50
F1
12 V
OUT
T1
R10
C52
C3
C12
+
AC INPUT
100 Vac – 240 Vac
EMI FILTER
REQUIRED
C55
R56
BR1
D2
R11
C1A
L50
D51
C18
5V
OUT
R12
RT1
C53
C54
D6
R55
C5
SEC
COMMON
R6
IC2
R50
UCC38C44
1
COMP
REF 8
2
FB
VCC 7
3
CS
OUT
6
4
RT/CT
GND
5
R16
Q1
IC2
C50
C13
R50
R53
R52
C51
K
IC3
A
R
R54
UDG–01071
Figure 4. Typical Off-Line Application
Figure 5 shows the forward converter with synchronous rectification. This application provides 48 V to 3.3 V at
10 A with over 85% efficiency and uses the UCC38C42 as the secondary-side controller and UCC3961 as the
primary-side startup control device.
www.ti.com
9
10
www.ti.com
46.4k
0.1uF
C5
7
6
5
4
3
2
AGnd
Ref
Rt
FB
SS
SD
OVS
R12
200
ucc3961
U1
R2
2
1
C7
8
9
10
11
12
13
14
T2
4
3
R4
1.5k
300
R13
C8
1uF
Q2
470pF
C6
76.8k
R5
R6
4.7
C10
2.7nF
0.1uF
C9
R8
R10
1k
5.1k
D1
R14
50k
R15
20k 40%
0.33
R9
Q1
C22
4.7nF
D3
20k
R24
20k
402
R25
20k
R26
R19
20
4.7
680pF
100
R28
3300pF
C12
5.6nF
C16
21.5k
C23
R17
R16
BAR74
R23
D5
BAR74
Q3
C17
4700pF
1500pF
C11
4
3
2
1
4
3
2
1
Vcc
DT
Rt/Ct
CS
FB
U2
LODR
BTLO
HIDR
7.5k
R18
UCC38C4x
PGND
5
6
7
8
C19
470uF
4700pF
U4
TPS2832
IN
BOOT
COMP
R27
4.7
10
R21
Q4
GND
OUT
Vcc
REF
5
6
7
8
2uF
C26
470uF
C20
0.22uF
C13
C14
1uF
C24
0.1uF
D6
BZX84C15LT1
PWRGND
0.1uF
C21
3r3V
100
R22
C15
1uF
+
100pF
Vs
CS
PGnd
Out
Vdd
St
UVS
2.4k
R3
1.2k
C25
0.047uF
R20
10
+
R11
0.22uF
10nF
1
+
C4
C3
470uF
C1
R1
32.4k
10k
D2
T1
C18
+
VinN
VinP
R7
1nF
C2
L1
4.7uH
SLUS458B – AUGUST 2001
APPLICATION INFORMATION
Figure 5. Forward Converter with Synchronous Rectification Using the UCC38C42
as the Secondary-Side Controller
SLUS458B – AUGUST 2001
TYPICAL CHARACTERISTICS
OSCILLATOR FREQUENCY
vs
TIMING RESISTANCE AND CAPACITANCE
OSCILLATOR DISCHARGE CURRENT
vs
TEMPERATURE
9.5
10 M
IDISCH – Oscillator Discharge Current – mA
CT = 220 pF
CT = 470 pF
f – Frequency – Hz
1M
CT = 1 nF
100 k
10 k
CT = 4.7 nF
CT = 2.2 nF
9.0
8.5
8.0
7.5
7.0
1k
1k
10 k
100 k
–50
–25
0
Figure 6
1.8
90
180
1.6
160
1.4
80
70
140
60
120
50
100
40
80
30
60
PHASE
MARGIN
10
0
1k
10 k
100 k
1M
Phase Margin – (°)
Gain – (dB)
GAIN
VREF – Offset Voltage – V
200
100
100
125
COMP to CS OFFSET VOLTAGE
vs
TEMPERATURE
100
10
75
Figure 7
ERROR AMPLIFIER
FREQUENCY RESPONSE
1
50
TJ – Temperature – °C
RT – Timing Resistance –
20
25
1.2
1.0
0.8
0.6
40
0.4
20
0.2
0
10 M
f – Frequency – Hz
0.0
–50
–25
0
25
50
75
100
125
TJ – Temperature – °C
Figure 8
Figure 9
www.ti.com
11
SLUS458B – AUGUST 2001
TYPICAL CHARACTERISTICS
REFERENCE VOLTAGE
vs
TEMPERATURE
ERROR AMPLIFIER REFERENCE VOLTAGE
vs
TEMPERATURE
VEAREF – Error Amplifier Reference Voltage – V
5.05
VREF – Reference Voltage – V
5.04
5.03
5.02
5.01
5.00
4.99
4.98
4.97
4.96
4.95
–50
–25
0
25
50
75
100
2.55
2.54
2.53
2.52
2.51
2.50
2.49
2.48
2.47
2.46
2.45
125
–50
–25
TJ – Temperature – °C
0
100
125
ERROR AMPLIFIER INPUT BIAS CURRENT
vs
TEMPERATURE
–35
200
IBIAS – Error Amplifier Input Bias Current – nA
ISC – Reference Short Circuit Current – mA
75
Figure 11
REFERENCE SHORT-CIRCUIT CURRENT
vs
TEMPERATURE
–37
–39
–41
–43
–45
–47
–49
–51
–53
150
100
50
0
–50
–100
–150
–200
–25
0
25
50
75
TJ – Temperature – °C
100
125
Figure 12
12
50
TJ – Temperature – °C
Figure 10
–55
–50
25
–50
–25
0
25
50
75
TJ – Temperature – °C
Figure 13
www.ti.com
100
125
SLUS458B – AUGUST 2001
TYPICAL CHARACTERISTICS
UNDERVOLTAGE LOCKOUT
vs
TEMPERATURE (UCC38C43 & UCC38C45)
UNDERVOLTAGE LOCKOUT
vs
TEMPERATURE (UCC38C42 & UCC38C44)
16
9.0
VUVLO – UVLO Voltage – V
14
13
UVLO
ON
12
UVLO
OFF
11
10
8.6
8.4
8.2
8.0
7.8
9
7.6
8
7.4
7
7.2
6
–50
UVLO
ON
8.8
–25
0
25
50
75
100
125
7.0
–50
UVLO
OFF
–25
0
TJ – Temperature – °C
Figure 14
25
50
75
TJ – Temperature – °C
100
125
Figure 15
UNDERVOLTAGE LOCKOUT
vs
TEMPERATURE (UCC38C40 & UCC38C41)
7.3
7.2
UVLO
ON
7.1
VUVLO – UVLO Voltage – V
VUVLO – UVLO Voltage – V
15
7.0
6.9
6.8
6.7
6.6
6.5
UVLO
OFF
6.4
6.3
–50
–25
0
25
50
75
100
125
TJ – Temperature – °C
Figure 16
www.ti.com
13
SLUS458B – AUGUST 2001
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
TEMPERATURE
SUPPLY CURRENT
vs
OSCILLATOR FREQUENCY
3.0
25
1-nF LOAD
20
2.8
IDD – Supply Current – mA
IDD – Supply Current – mA
2.9
15
10
NO LOAD
2.7
2.6
2.5
2.4
NO LOAD
2.3
2.2
5
2.1
2.0
–50
0
0k
200 k
400 k
600 k
f – Frequency – Hz
800 k
1M
–25
0
Figure 17
40
OUTPUT RISE TIME AND FALL TIME
vs
TEMPERATURE
75
100
125
MAXIMUM DUTY CYCLE
vs
OSCILLATOR FREQUENCY
100
10% to 90%
VDD = 12 V
CT = 220 pF
tr
(1 nF)
90
30
tf
(1 nF)
25
20
10
–50
80
70
CT = 1 nF
60
15
–25
0
25
50
75
100
125
TJ – Temperature – °C
50
0
500
1000
1500
f – Frequency – kHz
Figure 19
14
50
Figure 18
Duty Cycle – %
Output Rise and Fall TIme – ns
35
25
TJ – Temperature – °C
Figure 20
www.ti.com
2000
2500
SLUS458B – AUGUST 2001
TYPICAL CHARACTERISTICS
MAXIMUM DUTY CYCLE
vs
TEMPERATURE
MAXIMUM DUTY CYCLE
vs
TEMPERATURE
100
50
Output Rise and Fall TIme – ns
UCC38C40
UCC38C42
UCC38C43
Maximum Duty Cycle – %
98
96
94
92
UCC38C41
UCC38C44
UCC38C45
49
48
47
46
90
–50
–25
0
25
50
75
100
45
–50
125
–25
TJ – Temperature – °C
50
75
100
125
Figure 22
CURRENT SENSE THRESHOLD VOLTAGE
vs
TEMPERATURE
CS TO OUT DELAY TIME
vs
TEMPERATURE
70
65
1.05
tD – CD to OUT Delay Time – ns
VCS_th – Current Sense Threshold – V
25
TJ – Temperature – °C
Figure 21
1.10
0
1.00
0.95
60
55
50
45
40
35
0.90
–50
30
–25
0
25
50
75
100
125
TJ – Temperature – °C
–50
–25
0
25
50
75
100
125
TJ – Temperature – °C
Figure 24
Figure 23
www.ti.com
15
SLUS458B – AUGUST 2001
MECHANICAL DATA
D (SOIC)
PLASTIC SMALL-OUTLINE PACKAGE
Note: UCC38C4x is offered in an 8-pin package ONLY.
14 PINS SHOWN
0.050 (1,27)
0.020 (0,51)
0.014 (0,35)
14
0.010 (0,25) M
8
0.008 (0,20) NOM
0.244 (6,20)
0.228 (5,80)
0.157 (4,00)
0.150 (3,81)
Gage Plane
0.010 (0,25)
1
7
0°–ā8°
A
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
PINS **
0.004 (0,10)
8
14
16
A MAX
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MIN
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
DIM
4040047/D 10/96
NOTES: A.
B.
C.
D.
16
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
Falls within JEDEC MS-012
www.ti.com
SLUS458B – AUGUST 2001
MECHANICAL DATA
DGK (R-PDSO-G8)
PLASTIC SMALL-OUTLINE PACKAGE
0,38
0,25
0,65
8
0,25 M
5
0,15 NOM
3,05
2,95
4,98
4,78
Gage Plane
0,25
1
0°–ā6°
4
3,05
2,95
0,69
0,41
Seating Plane
1,07 MAX
0,15
0,05
0,10
4073329/B 04/98
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion.
Falls within JEDEC MO-187
www.ti.com
17
SLUS458B – AUGUST 2001
MECHANICAL DATA
P (PDIP)
PLASTIC DUAL-IN-LINE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.325 (8,26)
0.300 (7,62)
0.020 (0,51) MIN
0.015 (0,38)
Gage Plane
0.200 (5,08) MAX
Seating Plane
0.010 (0,25) NOM
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0.430 (10,92)
MAX
0.010 (0,25) M
4040082/D 05/98
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
18
www.ti.com
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its products to the specifications applicable at the time of sale in accordance with
TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary
to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except
those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
products or services might be or are used. TI’s publication of information regarding any third party’s products
or services does not constitute TI’s approval, license, warranty or endorsement thereof.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation
or reproduction of this information with alteration voids all warranties provided for an associated TI product or
service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use.
Resale of TI’s products or services with statements different from or beyond the parameters stated by TI for
that product or service voids all express and any implied warranties for the associated TI product or service,
is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use.
Also see: Standard Terms and Conditions of Sale for Semiconductor Products. www.ti.com/sc/docs/stdterms.htm
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2001, Texas Instruments Incorporated