ETC WS512K32

WS512K32-XXX
512Kx32 SRAM MODULE, SMD 5962-94611
FEATURES
n Access Times of 15*, 17, 20, 25, 35, 45, 55ns
n 5 Volt Power Supply
n Packaging
n Low Power CMOS
• 66 pin, PGA Type, 1.075" square, Hermetic Ceramic
HIP (Package 400).
n Built-in Decoupling Caps and Multiple Ground Pins for Low
Noise Operation
• 68 lead, 40mm Hermetic Low Profile CQFP, 3.5mm
(0.140") (Package 502)1, Package to be developed.
n Weight
WS512K32-XH1X - 13 grams typical
• 68 lead, Hermetic CQFP (G2T)1, 22.4mm (0.880") square
(Package 509) 4.57mm (0.180") height. Designed to fit
JEDEC 68 lead 0.990" CQFJ footprint (Fig. 3).
WS512K32-XG2TX1 - 8 grams typical
• 68 lead, Hermetic CQFP (G1U), 23.9mm (0.940") square
(Package 519) 3.57mm (0.140") height. Designed to fit
JEDEC 68 lead 0.990" CQFJ footprint (Fig. 3).
WS512K32-XG1TX - 5 grams typical
WS512K32-XG1UX - 5 grams typical
WS512K32-XG4TX1 - 20 grams typical
*15ns Access Time available only in Commercial and Industrial Temperature.
This speed is not fully characterized and is subject to change without notice.
Note 1: Package Not Recommended For New Design
• 68 lead, Hermetic CQFP (G1T), 23.9mm (0.940") square
(Package 524) 4.06mm (0.160") height.
n Organized as 512Kx32, User Configurable as 1Mx16 or
2Mx8
n Commercial, Industrial and Military Temperature Ranges
n TTL Compatible Inputs and Outputs
FIG. 1
P IN C ONFIGURATION F OR WS512K32N-XH1X
PIN DESCRIPTION
T OP VIEW
I/O 0-31
Data Inputs/Outputs
A0-18
Address Inputs
WE1-4
Write Enables
CS1-4
Chip Selects
OE
Output Enable
VCC
Power Supply
GND
Ground
NC
Not Connected
BLOCK DIAGRAM
November 2001 Rev. 9
1
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
WS512K32-XXX
FIG. 2
PIN C ONFIGURATION
FOR
WS512K32-XG4TX
1
TOP VIEW
PIN DESCRIPTION
I/O0-31
Data Inputs/Outputs
A0-18
Address Inputs
WE
Write Enables
CS1-4
Chip Selects
OE
Output Enable
VCC
Power Supply
GND
Ground
NC
Not Connected
BLOCK DIAGRAM
Note 1: Package Not Recommended For New Design
FIG. 3
1
PIN CONFIGURATION F OR WS512K32-XG2TX , WS512 K 32-XG 1TX
A ND WS512K32-XG1UX
T OP V IEW
PIN DESCRIPTION
The White 68 lead CQFP fills
the same fit and function as
the JEDEC 68 lead CQFJ or 68
PLCC. But it has the TCE and
lead inspection advantage of
the CQFP form.
I/O0-31
Data Inputs/Outputs
A0-18
Address Inputs
WE1-4
Write Enables
CS1-4
Chip Selects
OE
Output Enable
VCC
Power Supply
GND
Ground
NC
Not Connected
BLOCK DIAGRAM
Note 1: Package Not Recommended For New Design
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
2
WS512K32-XXX
A BSOLUTE MAXIMUM R ATINGS
Parameter
Symbol
TRUTH TABLE
Min
Max
Unit
TA
-55
+125
°C
Storage Temperature
TSTG
-65
+150
°C
Signal Voltage Relative to GND
VG
-0.5
Vcc+0.5
V
Junction Temperature
TJ
150
°C
7.0
V
Operating Temperature
Supply Voltage
-0.5
VCC
CS
OE
WE
Mode
Data I/O
Power
H
L
L
L
X
L
H
X
X
H
H
L
Standby
Read
Out Disable
Write
High Z
Data Out
High Z
Data In
Standby
Active
Active
Active
CAPACITANCE
RECOMMENDED OPERATING CONDITIONS
Parameter
(TA = +25°C)
Symbol
Min
Max
Unit
Supply Voltage
VCC
4.5
5.5
V
OE capacitance
COE
VIN = 0 V, f = 1.0 MHz
Input High Voltage
VIH
2.2
V CC + 0.3
V
CWE
VIN = 0 V, f = 1.0 MHz
Input Low Voltage
VIL
-0.5
+0.8
V
Operating Temp (Mil)
TA
-55
+125
°C
WE1-4 capacitance
HIP (PGA)
CQFP G4T
CQFP G2T/G1U/G1T
Parameter
Symbol
Conditions
Max
Unit
50
pF
pF
20
50
20
CS1-4 capacitance
CCS
VIN = 0 V, f = 1.0 MHz
20
pF
Data I/O capacitance
CI/O
VI/O = 0 V, f = 1.0 MHz
20
pF
Address input capacitance
CAD
VIN = 0 V, f = 1.0 MHz
50
pF
This parameter is guaranteed by design but not tested.
DC CHARACTERISTICS
(VCC = 5.0V, VSS = 0V, TA = -55°C
Parameter
Symbol
TO
+125°C)
Conditions
Units
Min
Max
Input Leakage Current
I LI
VCC = 5.5, VIN = GND to VCC
10
Output Leakage Current
I LO
CS = VIH, OE = VIH, VOUT = GND to VCC
10
µA
CS = VIL, OE = VIH, f = 5MHz, Vcc = 5.5
660
mA
Operating Supply Current x 32 Mode
ICC
x 32
µA
Standby Current
ISB
CS = VIH, OE = VIH, f = 5MHz, Vcc = 5.5
80
mA
Output Low Voltage
VOL
IOL = 8mA for 15 - 35ns,
IOL = 2.1mA for 45 - 55ns, Vcc = 4.5
0.4
V
Output High Voltage
VOH
IOH = -4.0mA for 15 - 35ns,
IOH = -1.0mA for 45 - 55ns, Vcc = 4.5
2.4
V
NOTE: DC test conditions: VIH = VCC -0.3V, VIL = 0.3V
DATA RETENTION CHARACTERISTICS
(TA = -55°C
Parameter
Symbol
TO
+125°C)
Conditions
Units
Min
Max
2.0
VDR
CS ³ V CC £ 0.2V
5.5
V
Data Retention Current
ICCDR1
V CC = 3V
28
mA
Low Power Data Retention
Current (WS512K32L-XXX)
ICCDR2
V CC = 3V
16
mA
Data Retention Supply Voltage
3
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
WS512K32-XXX
AC CHARACTERISTICS
(VCC = 5.0V, VSS = 0V, TA = -55°C
Parameter
-15*
Symbol
Read Cycle
Min
Read Cycle Time
t RC
Address Access Time
tAA
Output Hold from Address Change
tOH
Chip Select Access Time
t ACS
-17
Max
15
Min
-20
Max
Min
17
15
0
Max
20
-25
-35
Max
0
Min
Min
Max
Max
ns
45
0
55
ns
55
ns
25
ns
0
35
12
Min
Units
55
35
25
10
-55
45
0
20
9
Max
25
0
17
-45
35
20
0
8
+125°C)
25
17
15
Min
TO
ns
45
Output Enable to Output Valid
tOE
Chip Select to Output in Low Z
t CLZ 1
2
2
2
2
4
25
4
25
4
Output Enable to Output in Low Z
t OLZ 1
0
0
0
0
0
0
0
Chip Disable to Output in High Z
t CHZ 1
12
12
12
12
15
20
20
ns
Output Disable to Output in High Z
t OHZ1
12
12
12
12
15
20
20
ns
ns
ns
*15ns Access Time available only in Commercial and Industrial Temperature. This speed is not fully characterized and is subject to change without notice.
1. This parameter is guaranteed by design but not tested.
AC CHARACTERISTICS
(VCC = 5.0V, VS S = 0V, TA = -55°C
Parameter
Symbol
Write Cycle
-15*
Min
-17
Max
Min
-20
Max
Min
TO
+125°C)
-25
Max
Min
-35
Max
Min
-45
Max
Min
-55
Max
Min
Units
Max
Write Cycle Time
t WC
15
17
20
25
35
45
55
ns
Chip Select to End of Write
t CW
13
15
15
17
25
35
50
ns
Address Valid to End of Write
t AW
13
15
15
17
25
35
50
ns
Data Valid to End of Write
t DW
10
11
12
13
20
25
25
ns
Write Pulse Width
t WP
13
15
15
17
25
35
40
ns
Address Setup Time
t AS
2
2
2
2
2
2
2
ns
Address Hold Time
t AH
0
0
0
0
0
5
5
ns
Output Active from End of Write
t OW 1
2
2
3
4
4
5
5
Write Enable to Output in High Z
t WHZ 1
Data Hold Time
tDH
8
0
9
11
0
0
13
0
15
0
ns
20
0
20
0
ns
*15ns Access Time available only in Commercial and Industrial Temperature. This speed is not fully characterized and is subject to change without notice.
1. This parameter is guaranteed by design but not tested.
2. The Address Setup Time of minimum 2ns is for the G2T, G1U and H1 packages. tAS minimum for the G4T package is 0ns.
F IG . 4
AC T EST C ONDITIONS
AC T EST C IRCUIT
Parameter
Typ
Unit
Input Pulse Levels
VIL = 0, VIH = 3.0
V
Input Rise and Fall
5
ns
Input and Output Reference Level
1.5
V
Output Timing Reference Level
1.5
V
Notes:
VZ is programmable from -2V to +7V.
IOL & IOH programmable from 0 to 16mA.
Tester Impedance Z0 = 75 ý.
VZ is typically the midpoint of VOH and VOL.
IOL & IOH are adjusted to simulate a typical resistive load circuit.
ATE tester includes jig capacitance.
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
4
ns
WS512K32-XXX
F IG. 5
T IMING W AVEFORM - R EAD C YCLE
F IG . 6 W RITE CYCLE - WE C ONTROLLED
F IG . 7
W RITE C YCLE - CS C ONTROLLED
WS32K32-XHX
5
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
WS512K32-XXX
P ACKAGE 400:
66 PIN , PGA T YPE , C ERAMIC H E X -IN -L INE P ACK AGE , H IP (H1)
ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES
P ACK AGE 502:
68 LEAD , C ERAMIC Q UAD F L AT P ACK , L OW P ROFILE CQFP (G4T)
1
ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES
Note 1: Package Not Recommended For New Design
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
6
WS512K32-XXX
P ACK AGE 509:
68 LEAD , C ERAMIC Q UAD F L AT P ACK , CQFP (G2T)
1
The White 68 lead G2T CQFP
fills the same fit and function
as the JEDEC 68 lead CQFJ or
68 PLCC. But the G2T has the
TCE and lead inspection
advantage of the CQFP form.
ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES
Note 1: Package Not Recommended For New Design
7
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
WS512K32-XXX
P ACK AGE 519:
68 LEAD , C ERAMIC Q UAD F L AT P ACK, L OW P ROFILE CQFP (G1U)
The White 68 lead G1U CQFP
fills the same fit and function
as the JEDEC 68 lead CQFJ or
68 PLCC. But the G1U has the
TCE and lead inspection
advantage of the CQFP form.
ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
8
WS512K32-XXX
P ACK AGE 524:
68 LEAD , C ERAMIC Q UAD F L AT P ACK , L OW PROFILE CQFP (G1T)
The White 68 lead G1T CQFP
fills the same fit and function
as the JEDEC 68 lead CQFJ or
68 PLCC. But the G1T has the
TCE and lead inspection
advantage of the CQFP form.
ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES
9
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
WS512K32-XXX
ORDERING INFORMATION
W S
512K 32
X - XXX X X X
LEAD FINISH:
Blank = Gold plated leads
A = Solder dip leads
DEVICE GRADE:
Q = MIL-STD-883 Compliant
M = Military Screened
-55°C to +125°C
I = Industrial
-40°C to 85°C
C = Commercial
0°C to +70°C
PACKAGE TYPE:
H1 = Ceramic Hex-In-line Package, HIP (Package 400)
G2T1 = 22.4mm Ceramic Quad Flat Pack, CQFP (Package 509)
G4T1 = 40mm Low Profile CQFP (Package 502)
G1U = 23.9mm Low Profile CQFP (Package 519)
G1T = 23.9mm Low Profile CQFP (Package 524)
ACCESS TIME (ns)
IMPROVEMENT MARK:
Blank = Standard Power
N = No Connect at pin 21 and 39 in HIP for Upgrades
L = Low Power Data Retention
ORGANIZATION, 512Kx32
User configurable as 1Mx16 or 2Mx8
SRAM
WHITE ELECTRONIC DESIGNS CORP.
Note 1: Package Not Recommended For New Design
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com
10
WS512K32-XXX
DEVICE TYPE
SPEED
PACKAGE
SMD NO.
512K x 32 SRAM Module
55ns
66 pin HIP (H1)
5962-94611 05HTX
512K x 32 SRAM Module
45ns
66 pin HIP (H1)
5962-94611 06HTX
512K x 32 SRAM Module
35ns
66 pin HIP (H1)
5962-94611 07HTX
512K x 32 SRAM Module
25ns
66 pin HIP (H1)
5962-94611 08HTX
512K x 32 SRAM Module
20ns
66 pin HIP (H1)
5962-94611 09HTX
512K x 32 SRAM Module
17ns
66 pin HIP (H1)
5962-94611 10HTX
512K x 32 SRAM Module
55ns
68 lead CQFP Low Profile (G4T)1
5962-94611 05HYX
512K x 32 SRAM Module
45ns
68 lead CQFP Low Profile (G4T)1
5962-94611 06HYX
512K x 32 SRAM Module
35ns
68 lead CQFP Low Profile (G4T)1
5962-94611 07HYX
512K x 32 SRAM Module
25ns
68 lead CQFP Low Profile (G4T)1
5962-94611 08HYX
512K x 32 SRAM Module
20ns
68 lead CQFP Low Profile (G4T)1
5962-94611 09HYX
512K x 32 SRAM Module
17ns
68 lead CQFP Low Profile (G4T)
1
5962-94611 10HYX
512K x 32 SRAM Module
55ns
68 lead CQFP (G2T)1
5962-94611 05HMX
512K x 32 SRAM Module
45ns
68 lead CQFP (G2T)1
5962-94611 06HMX
512K x 32 SRAM Module
35ns
68 lead CQFP (G2T)1
5962-94611 07HMX
512K x 32 SRAM Module
25ns
68 lead CQFP (G2T)
1
5962-94611 08HMX
512K x 32 SRAM Module
20ns
68 lead CQFP (G2T)1
5962-94611 09HMX
512K x 32 SRAM Module
17ns
68 lead CQFP (G2T)1
5962-94611 10HMX
512K x 32 SRAM Module
55ns
68 lead CQFP (G1U)
5962-94611 05H9X
512K x 32 SRAM Module
45ns
68 lead CQFP (G1U)
5962-94611 06H9X
512K x 32 SRAM Module
35ns
68 lead CQFP (G1U)
5962-94611 07H9X
512K x 32 SRAM Module
25ns
68 lead CQFP (G1U)
5962-94611 08H9X
512K x 32 SRAM Module
20ns
68 lead CQFP (G1U)
5962-94611 09H9X
512K x 32 SRAM Module
17ns
68 lead CQFP (G1U)
5962-94611 10H9X
Note 1: Package Not Recommended For New Design
11
White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com