NSC LMK03200ISQX

LMK03200 Family
Precision 0-Delay Clock Conditioner with Integrated VCO
General Description
Features
The LMK03200 family of precision clock conditioners combine the functions of jitter cleaning/reconditioning, multiplication, and 0-delay distribution of a reference clock. The devices
integrate a Voltage Controlled Oscillator (VCO), a high performance Integer-N Phase Locked Loop (PLL), a partially
integrated loop filter, and up to eight outputs in various LVDS
and LVPECL combinations.
The VCO output is optionally accessible on the Fout port. Internally, the VCO output goes through a VCO divider to feed
the various clock distribution blocks.
Each clock distribution block includes a programmable divider, a phase synchronization circuit, a programmable delay,
a clock output mux, and an LVDS or LVPECL output buffer.
The PLL also features delay blocks to permit global phase
adjustment of clock output phase. This allows multiple integer-related and phase-adjusted copies of the reference to be
distributed to eight system components.
The clock conditioners come in a 48-pin LLP package and are
footprint compatible with other clocking devices in the same
family.
■ Integrated VCO with very low phase noise floor
■ Integrated Integer-N PLL with outstanding normalized
phase noise contribution of -224 dBc/Hz
■ VCO divider values of 2 to 8 (all divides)
■
■
■
■
■
■
■
■
■
■
■
— Bypassable with VCO Mux when not in 0-delay mode
Channel divider values of 1, 2 to 510 (even divides)
LVDS and LVPECL clock outputs
Partially integrated loop filter
Dedicated divider and delay blocks on each clock output
0-delay outputs
Internal or external feedback of output clock
Delay blocks on N and R phase detector inputs for lead/
lag global skew adjust
Pin compatible family of clocking devices
3.15 to 3.45 V operation
Package: 48 pin LLP (7.0 x 7.0 x 0.8 mm)
200 fs RMS Clock generator performance (10 Hz to 20
MHz) with a clean input clock
Target Applications
■
■
■
■
■
■
VCO
Data Converter Clocking
Networking, SONET/SDH, DSLAM
Wireless Infrastructure
Medical
Test and Measurement
Military / Aerospace
Device
Outputs
LMK03200
3 LVDS
5 LVPECL
Tuning Range RMS Jitter
(MHz)
(fs)
1185 - 1296
800
System Diagram
30088740
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
© 2009 National Semiconductor Corporation
300887
www.national.com
LMK03200 Family Precision 0-Delay Clock Conditioner with Integrated VCO
August 20, 2009
LMK03200 Family
Functional Block Diagram
30088701
www.national.com
2
General Description .............................................................................................................................. 1
Target Applications ............................................................................................................................... 1
Features .............................................................................................................................................. 1
System Diagram ................................................................................................................................... 1
Functional Block Diagram ...................................................................................................................... 2
Connection Diagram ............................................................................................................................. 5
Pin Descriptions .................................................................................................................................. 6
Absolute Maximum Ratings .................................................................................................................... 7
Recommended Operating Conditions ..................................................................................................... 7
Package Thermal Resistance ................................................................................................................. 7
Electrical Characteristics ....................................................................................................................... 8
Serial Data Timing Diagram ................................................................................................................ 11
Charge Pump Current Specification Definitions ................................................................................ 12
Typical Performance Characteristics ..................................................................................................... 13
1.0 Functional Description .................................................................................................................... 14
1.1 BIAS PIN .............................................................................................................................. 14
1.2 LDO BYPASS ........................................................................................................................ 14
1.3 OSCILLATOR INPUT PORT (OSCin, OSCin*) ........................................................................... 14
1.4 LOW NOISE, FULLY INTEGRATED VCO ................................................................................. 14
1.5 LVDS/LVPECL OUTPUTS ...................................................................................................... 14
1.6 GLOBAL CLOCK OUTPUT SYNCHRONIZATION ...................................................................... 15
1.7 CLKout OUTPUT STATES ...................................................................................................... 15
1.8 GLOBAL OUTPUT ENABLE AND LOCK DETECT ..................................................................... 15
1.9 POWER ON RESET ............................................................................................................... 15
1.10 DIGITAL LOCK DETECT ....................................................................................................... 16
1.11 CLKout DELAYS .................................................................................................................. 16
1.12 GLOBAL DELAYS ................................................................................................................ 17
1.13 VCO DIVIDER BYPASS MODE .............................................................................................. 17
1.14 0-DELAY MODE .................................................................................................................. 17
2.0 General Programming Information ................................................................................................... 18
2.1 Recommended Programming Sequence, without 0-Delay Mode ................................................... 18
2.2 Recommended Programing Sequence, with 0-Delay Mode .......................................................... 18
2.2.1 0-Delay Mode Example 1 .............................................................................................. 19
2.2.2 0-Delay Mode Example 2 .............................................................................................. 19
2.3 Recommended Programming Sequence, bypassing VCO divider ................................................. 20
2.3.1 VCO divider bypass example ......................................................................................... 20
2.4 Register R0 to R7 ................................................................................................................... 24
2.4.1 Reset bit -- Reset device to power on defaults .................................................................. 24
2.4.2 DLD_MODE2 bit -- Digital Lock Detect Mode 2 ................................................................. 24
2.4.3 0_DELAY_MODE bit -- Activate 0-Delay Mode ................................................................. 25
2.4.4 FB_MUX [1:0] -- Feedback Mux ..................................................................................... 25
2.4.5 VCO_MUX [1:0] -- VCO Mux .......................................................................................... 25
2.4.6 CLKoutX_MUX [1:0] -- Clock Output Multiplexers .............................................................. 25
2.4.7 CLKoutX_DIV [7:0] -- Clock Output Dividers ..................................................................... 26
2.4.8 CLKoutX_DLY [3:0] -- Clock Output Delays ...................................................................... 26
2.4.9 CLKoutX_EN bit -- Clock Output Enables ........................................................................ 26
2.5 Register R8 ........................................................................................................................... 26
2.6 Register R9 ........................................................................................................................... 26
2.6.1 Vboost bit -- Voltage Boost ............................................................................................ 26
2.7 Register R11 ......................................................................................................................... 27
2.7.1 DIV4 -- High Phase Detector Frequencies and Lock Detect ................................................ 27
2.8 Register R13 ......................................................................................................................... 27
2.8.1 VCO_C3_C4_LF [3:0] -- Value for Internal Loop Filter Capacitors C3 and C4 ....................... 27
2.8.2 VCO_R3_LF [2:0] -- Value for Internal Loop Filter Resistor R3 ............................................ 27
2.8.3 VCO_R4_LF [2:0] -- Value for Internal Loop Filter Resistor R4 ............................................ 27
2.8.4 OSCin_FREQ [7:0] -- Oscillator Input Calibration Adjustment ............................................. 27
2.9 Register R14 ......................................................................................................................... 27
2.9.1 PLL_R [11:0] -- R Divider Value ...................................................................................... 27
2.9.2 PLL_MUX[3:0] -- Multiplexer Control for LD Pin ................................................................ 28
2.9.3 POWERDOWN bit -- Device Power Down ....................................................................... 28
2.9.4 EN_CLKout_Global bit -- Global Clock Output Enable ....................................................... 28
2.9.5 EN_Fout bit -- Fout port enable ...................................................................................... 28
2.9.6 PLL_R_DLY [3:0] - Global Skew Adjust, Lag .................................................................... 28
2.10 REGISTER R15 ................................................................................................................... 28
3
www.national.com
LMK03200 Family
Table of Contents
LMK03200 Family
2.10.1 PLL_N [17:0] -- PLL N Divider ......................................................................................
2.10.2 VCO_DIV [3:0] -- VCO Divider ......................................................................................
2.10.3 PLL_CP_GAIN [1:0] -- PLL Charge Pump Gain ..............................................................
2.10.4 PLL_N_DLY [3:0] - Global Skew Adjust, Lead .................................................................
3.0 Application Information ...................................................................................................................
3.1 SYSTEM LEVEL DIAGRAM ....................................................................................................
3.2 BIAS PIN ..............................................................................................................................
3.3 LDO BYPASS ........................................................................................................................
3.4 LOOP FILTER .......................................................................................................................
3.5 CURRENT CONSUMPTION / POWER DISSIPATION CALCULATIONS .......................................
3.6 THERMAL MANAGEMENT .....................................................................................................
3.7 TERMINATION AND USE OF CLOCK OUTPUTS (DRIVERS) .....................................................
3.7.1 Termination for DC Coupled Differential Operation ............................................................
3.7.2 Termination for AC Coupled Differential Operation ............................................................
3.7.3 Termination for Single-Ended Operation ..........................................................................
3.7.4 Conversion to LVCMOS Outputs ....................................................................................
3.8 OSCin INPUT ........................................................................................................................
3.9 MORE THAN EIGHT OUTPUTS WITH AN LMK03200 FAMILY DEVICE .......................................
3.10 DIFFERENTIAL VOLTAGE MEASUREMENT TERMINOLOGY ..................................................
Physical Dimensions ...........................................................................................................................
Ordering Information ...........................................................................................................................
28
29
29
30
31
31
31
31
32
33
34
34
34
35
36
36
36
37
38
39
39
List of Figures
FIGURE 1. Frequency Calibration Routine Flowchart ........................................................................................
FIGURE 2. SYNC* Timing Diagram .............................................................................................................
FIGURE 3. Digital Lock Detect Flowchart ......................................................................................................
FIGURE 4. Global Lead and Lag .................................................................................................................
FIGURE 5. Outline of 0-delay mode programming sequence ...............................................................................
FIGURE 6. Typical Application ...................................................................................................................
FIGURE 7. Loop Filter .............................................................................................................................
FIGURE 8. Differential LVDS Operation, DC Coupling .......................................................................................
FIGURE 9. Differential LVPECL Operation, DC Coupling ...................................................................................
FIGURE 10. Differential LVPECL Operation, DC Coupling, Thevenin Equivalent .......................................................
FIGURE 11. Differential LVDS Operation, AC Coupling .....................................................................................
FIGURE 12. Differential LVPECL Operation, AC Coupling, Thevenin Equivalent .......................................................
FIGURE 13. Single-Ended LVPECL Operation, DC Coupling ..............................................................................
FIGURE 14. Single-Ended LVPECL Operation, DC Coupling, Thevenin Equivalent ...................................................
FIGURE 15. Single-Ended LVPECL Operation, AC Coupling ..............................................................................
FIGURE 16. Single-Ended Sine Wave Input ...................................................................................................
FIGURE 17. Differential Sine Wave Input ......................................................................................................
FIGURE 18. Recommended OSCin Power for Operation with a Sine Wave Input ......................................................
FIGURE 19. Two Different Definitions for Differential Input Signals .......................................................................
FIGURE 20. Two Different Definitions for Differential Output Signals .....................................................................
www.national.com
4
14
15
16
17
17
31
32
34
35
35
35
35
36
36
36
36
37
37
38
38
LMK03200 Family
Connection Diagram
48-Pin LLP Package
30088702
5
www.national.com
LMK03200 Family
Pin Descriptions
Pin #
Pin Name
I/O
1, 25
GND
-
Ground
2
Fout
O
Internal VCO Frequency Output
-
Power Supply
3, 8, 13, 16, 19, 22,
Vcc1, Vcc2, Vcc3, Vcc4, Vcc5, Vcc6, Vcc7, Vcc8, Vcc9, Vcc10,
26, 30, 31, 33, 37,
Vcc11, Vcc12, Vcc13, Vcc14
40, 43, 46
Description
4
CLKuWire
I
MICROWIRE Clock Input
5
DATAuWire
I
MICROWIRE Data Input
6
LEuWire
I
MICROWIRE Latch Enable Input
7
NC
-
No Connection to these pins
9, 10
LDObyp1, LDObyp2
-
LDO Bypass
11
GOE
I
Global Output Enable
12
LD
O
Lock Detect and Test Output
14, 15
CLKout0, CLKout0*
O
LVDS Clock Output 0
17, 18
CLKout1, CLKout1*
O
LVDS Clock Output 1
20, 21
CLKout2, CLKout2*
O
LVDS Clock Output 2
23, 24
CLKout3, CLKout3*
O
LVPECL Clock Output 3
27
SYNC*
I
Global Clock Output Synchronization
28, 29
OSCin, OSCin*
I
Oscillator Clock Input; Should be AC
coupled
32
CPout
O
Charge Pump Output
34, 35
FBCLKin, FBCLKin*
I
External Feedback Clock Input for 0delay mode
36
Bias
I
Bias Bypass
38, 39
CLKout4, CLKout4*
O
LVPECL Clock Output 4
41, 42
CLKout5, CLKout5*
O
LVPECL Clock Output 5
44, 45
CLKout6, CLKout6*
O
LVPECL Clock Output 6
47, 48
CLKout7, CLKout7*
O
LVPECL Clock Output 7
DAP
DAP
-
Die Attach Pad is Ground
www.national.com
6
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors
for availability and specifications.
Parameter
Symbol
VCC
Ratings
Units
-0.3 to 3.6
V
VIN
-0.3 to (VCC + 0.3)
V
TSTG
-65 to 150
°C
Lead Temperature (solder 4 s)
TL
+260
°C
Junction Temperature
TJ
125
°C
Power Supply Voltage
Input Voltage
Storage Temperature Range
Recommended Operating Conditions
Symbol
TA
Min
Typ
Max
Units
Ambient Temperature
Parameter
-40
25
85
°C
Power Supply Voltage
VCC
3.15
3.3
3.45
V
Note 1: "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability
and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in
the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the
device should not be operated beyond such conditions.
Note 2: This device is a high performance integrated circuit with ESD handling precautions. Handling of this device should only be done at ESD protected work
stations. The device is rated to a HBM-ESD of > 2 kV, a MM-ESD of > 200 V, and a CDM-ESD of > 1.2 kV.
Package Thermal Resistance
Package
θJA
θJ-PAD (Thermal Pad)
48-Lead LLP (Note 3)
27.4° C/W
5.8° C/W
Note 3: Specification assumes 16 thermal vias connect the die attach pad to the embedded copper plane on the 4-layer JEDEC board. These vias play a key
role in improving the thermal performance of the LLP. It is recommended that the maximum number of vias be used in the board layout.
7
www.national.com
LMK03200 Family
Absolute Maximum Ratings (Notes 1, 2)
LMK03200 Family
Electrical Characteristics
(Note 4)
(3.15 V ≤ Vcc ≤ 3.45 V, -40 °C ≤ TA ≤ 85 °C, Differential Inputs/Outputs; Vboost=0; except as specified. Typical values represent
most likely parametric norms at Vcc = 3.3 V, TA = 25 °C, and at the Recommended Operation Conditions at the time of product
characterization and are not guaranteed).
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Current Consumption
ICC
ICCPD
Entire device; one LVDS and one
LVPECL clock enabled; no divide; no
delay.
Power Supply Current
(Note 5)
Power Down Current
161.8
mA
Entire device; All Outputs Off (no
emitter resistors placed)
86
POWERDOWN = 1
5
mA
Reference Oscillator Input
fOSCin
Reference Oscillator Input Frequency
Range
VIDOSCin
Reference Oscillator Differential Input
Voltage (Notes 6, 13)
VOSCin
Reference Oscillator Single-ended Input
Voltage (Note 13)
SLEWOSCin
Reference Oscillator Input Slew Rate (Note
20% to 80%; For each input pin
13)
fFBCLKin
External Feedback Clock Input Frequency
Range
VIDFBCLKin
1
200
MHz
AC coupled
0.2
1.6
V
AC coupled; Unused pin AC coupled to
GND
0.2
2.0
Vpp
0.15
0.5
V/ns
External Feedback Clock Input
1
800
MHz
External Feedback Clock Differential Input
AC coupled
Voltage (Notes 6, 13)
0.2
1.6
V
VFBCLKin
External Feedback Clock Single-ended
Input Voltage (Note 13)
0.2
2.0
Vpp
SLEWFBCLKin
External Feedback Clock Input Slew Rate
20% to 80%; For each input pin
(Note 13)
fPD
Phase Detector Frequency
AC coupled; Unused pin AC coupled to
GND
0.15
0.5
V/ns
PLL
ISRCECPout
ISINKCPout
40
Charge Pump Source Current
Charge Pump Sink Current
TRI-STATE®
ICPoutTRI
Charge Pump
ICPout%MIS
Magnitude of Charge Pump
Sink vs. Source Current Mismatch
Current
Magnitude of Charge Pump
ICPoutVTUNE Current vs. Charge Pump Voltage
Variation
ICPoutTEMP
www.national.com
VCPout = Vcc/2, PLL_CP_GAIN = 1x
100
VCPout = Vcc/2, PLL_CP_GAIN = 4x
400
VCPout = Vcc/2, PLL_CP_GAIN = 16x
1600
VCPout = Vcc/2, PLL_CP_GAIN = 32x
3200
VCPout = Vcc/2, PLL_CP_GAIN = 1x
-100
VCPout = Vcc/2, PLL_CP_GAIN = 4x
-400
VCPout = Vcc/2, PLL_CP_GAIN = 16x
-1600
VCPout = Vcc/2, PLL_CP_GAIN = 32x
-3200
MHz
µA
μA
0.5 V < VCPout < Vcc - 0.5 V
2
VCPout = Vcc / 2
TA = 25°C
3
%
0.5 V < VCPout < Vcc - 0.5 V
TA = 25°C
4
%
4
%
Magnitude of Charge Pump Current vs.
Temperature Variation
8
10
nA
Parameter
Conditions
Min
Typ
Max
Units
PLL (Continued)
PN10kHz
PLL 1/f Noise at 10 kHz Offset (Note 7)
Normalized to 1 GHz Output Frequency
PLL_CP_GAIN = 1x
-117
PLL_CP_GAIN = 32x
-122
PN1Hz
Normalized Phase Noise Contribution
(Note 8)
PLL_CP_GAIN = 1x
-219
PLL_CP_GAIN = 32x
-224
dBc/Hz
dBc/Hz
VCO
fFout
VCO Tuning Range
LMK03200
|ΔTCL|
Allowable Temperature Drift for
Continuous Lock
After programming R15 for lock, only
changes 0_DELAY_MODE and
PLL_N for the purpose of enabling 0delay mode permitted to guarantee
continuous lock. (Note 9)
pFout
Output Power to a 50 Ω load driven by Fout
LMK03200; TA = 25 °C
(Note 11)
KVCO
Fine Tuning Sensitivity (Note 10)
JRMSFout
Fout RMS Period Jitter
(12 kHz to 20 MHz bandwidth)
1185
1296
MHz
125
°C
3.3
dBm
LMK03200
7 to 9
MHz/V
LMK03200
800
fs
Clock Skew and Delay
CLKoutX to CLKoutY (Note 13)
Equal loading and identical clock
configuration
RL = 100 Ω
-30
±4
30
ps
tSKEWLVPEC
CLKoutX to CLKoutY (Note 13)
L
Equal loading and identical clock
configuration
RL = 100 Ω
-30
±3
30
ps
0-Delay mode active; PLL_N_DLY = 0;
PLL_R_DLY = 0; FB_MUX = 0
(CLKout5)
-300
-65
300
0-Delay mode active; PLL_N_DLY = 0;
PLL_R_DLY = 0; FB_MUX = 2
(CLKout6)
-300
35
300
0-Delay mode active; PLL_N_DLY = 0;
PLL_R_DLY = 0; FB_MUX = 1
(FBCLKin)
-700
-400
-100
0-Delay mode active; PLL_N_DLY = 0;
PLL_R_DLY = 3; FB_MUX = 1
(FBCLKin)
-400
35
400
tSKEWLVDS
td0-DELAY
OSCin to CLKoutX delay (Note 13)
9
ps
www.national.com
LMK03200 Family
Symbol
LMK03200 Family
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Clock Distribution Section - LVDS Clock Outputs (Note 12)
JitterADD
RL = 100 Ω
Distribution Path =
765 MHz
Bandwidth =
12 kHz to 20 MHz
Additive RMS Jitter (Note 12)
CLKoutX_MUX
= Bypass (no
divide or delay)
20
CLKoutX_MUX
= Divided (no
delay)
CLKoutX_DIV =
4
fs
75
VOD
Differential Output Voltage
RL = 100 Ω
250
ΔVOD
Change in magnitude of VOD for
complementary output states
RL = 100 Ω
-50
VOS
Output Offset Voltage
RL = 100 Ω
1.070
ΔVOS
Change in magnitude of VOS for
complementary output states
RL = 100 Ω
ISA
ISB
Clock Output Short Circuit Current
single-ended
ISAB
Clock Output Short Circuit Current
differential
350
450
mV
50
mV
1.370
V
-35
35
mV
Single-ended outputs shorted to GND
-24
24
mA
Complementary outputs tied together
-12
12
mA
1.25
Clock Distribution Section (Note 12) - LVPECL Clock Outputs
JitterADD
VOH
Additive RMS Jitter (Note 12)
RL = 100 Ω
Distribution Path =
765 MHz
Bandwidth =
12 kHz to 20 MHz
CLKoutX_MUX
= Bypass (no
divide or delay)
20
CLKoutX_MUX
= Divided (no
delay)
CLKoutX_DIV =
4
fs
75
Output High Voltage
Termination = 50 Ω to Vcc - 2 V
Vcc 0.98
V
Vcc 1.8
V
VOL
Output Low Voltage
VOD
Differential Output Voltage
VIH
High-Level Input Voltage
VIL
Low-Level Input Voltage
0.8
V
IIH
High-Level Input Current
VIH = Vcc
-5.0
5.0
µA
IIL
Low-Level Input Current
VIL = 0
-40.0
5.0
µA
Vcc 0.4
RL = 100 Ω
660
810
965
mV
Vcc
V
Digital LVTTL Interfaces (Note 14)
2.0
VOH
High-Level Output Voltage
IOH = +500 µA
VOL
Low-Level Output Voltage
IOL = -500 µA
VIH
High-Level Input Voltage
VIL
Low-Level Input Voltage
0.4
V
IIH
High-Level Input Current
VIH = Vcc
-5.0
5.0
µA
IIL
Low-Level Input Current
VIL = 0
-5.0
5.0
µA
V
0.4
V
Vcc
V
Digital MICROWIRE Interfaces (Note 15)
www.national.com
1.6
10
Parameter
Conditions
Min
Typ
Max
Units
MICROWIRE Timing
tCS
Data to Clock Set Up Time
See Data Input Timing
tCH
Data to Clock Hold Time
tCWH
Clock Pulse Width High
tCWL
tES
25
ns
See Data Input Timing
8
ns
See Data Input Timing
25
ns
Clock Pulse Width Low
See Data Input Timing
25
ns
Clock to Enable Set Up Time
See Data Input Timing
25
ns
tCES
Enable to Clock Set Up Time
See Data Input Timing
25
ns
tEWH
Enable Pulse Width High
See Data Input Timing
25
ns
Note 4: The Electrical Characteristics table lists guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified
or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed.
Note 5: See Section 3.5 CURRENT CONSUMPTION / POWER DISSIPATION CALCULATIONS for more information.
Note 6: See Section 3.10 DIFFERENTIAL VOLTAGE MEASUREMENT TERMINOLOGY for more information.
Note 7: A specification in modeling PLL in-band phase noise is the 1/f flicker noise, LPLL_flicker(f), which is dominant close to the carrier. Flicker noise has a 10
dB/decade slope. PN10kHz is normalized to a 10 kHz offset and a 1 GHz carrier frequency. PN10kHz = LPLL_flicker(10 kHz) - 20log(Fout / 1 GHz), where LPLL_flicker
(f) is the single side band phase noise of only the flicker noise's contribution to total noise, L(f). To measure LPLL_flicker(f) it is important to be on the 10 dB/decade
slope close to the carrier. A high compare frequency and a clean crystal are important to isolating this noise source from the total phase noise, L(f). LPLL_flicker(f)
can be masked by the reference oscillator performance if a low power or noisy source is used. The total PLL in-band phase noise performance is the sum of
LPLL_flicker(f) and LPLL_flat(f).
Note 8: A specification in modeling PLL in-band phase noise is the Normalized Phase Noise Contribution, LPLL_flat(f), of the PLL and is defined as PN1Hz =
LPLL_flat(f) – 20log(N) – 10log(fCOMP). LPLL_flat(f) is the single side band phase noise measured at an offset frequency, f, in a 1 Hz Bandwidth and fCOMP is the phase
detector frequency of the synthesizer. LPLL_flat(f) contributes to the total noise, L(f). To measure LPLL_flat(f) the offset frequency, f, must be chosen sufficiently
smaller then the loop bandwidth of the PLL, and yet large enough to avoid a substantial noise contribution from the reference and flicker noise. LPLL_flat(f) can be
masked by the reference oscillator performance if a low power or noisy source is used.
Note 9: Allowable Temperature Drift for Continuous Lock is how far the temperature can drift in either direction and stay in lock from the ambient temperature
and programmed state at which the device was when the frequency calibration routine was run. The action of programming the R15 register, even to the same
value, when 0_DELAY_MODE = 0 activates a frequency calibration routine. This implies that the device will work over the entire frequency range, but if the
temperature drifts more than the maximum allowable drift for continuous lock, then it will be necessary to reprogram the R15 register while 0_DELAY_MODE =
0 to ensure that the device stays in lock. Regardless of what temperature the device was initially programmed at, the ambient temperature can never drift outside
the range of -40 °C ≤ TA ≤ 85 °C without violating specifications. For this specification to be valid, the programmed state of the device must not change after
R15 is programmed except for 0_DELAY_MODE and PLL_N for the purpose of enabling 0-delay mode.
Note 10: The lower sensitivity indicates the typical sensitivity at the lower end of the tuning range, the higher sensitivity at the higher end of the tuning range
Note 11: Output power varies as a function of frequency. When a range is shown, the higher output power applies to the lower frequency and the lower output
power applies to the higher frequency.
Note 12: The Clock Distribution Section includes all parts of the device except the PLL and VCO sections. Typical Additive Jitter specifications apply to the clock
distribution section only and this adds in an RMS fashion to the shaped jitter of the PLL and the VCO.
Note 13: Specification is guaranteed by characterization and is not tested in production.
Note 14: Applies to GOE, LD, and SYNC*.
Note 15: Applies to CLKuWire, DATAuWire, and LEuWire.
Serial Data Timing Diagram
30088703
Data bits set on the DATAuWire signal are clocked into a shift register, MSB first, on each rising edge of the CLKuWire signal. On
the rising edge of the LEuWire signal, the data is sent from the shift register to the addressed register determined by the LSB bits.
After the programming is complete the CLKuWire, DATAuWire, and LEuWire signals should be returned to a low state. It is recommended that the slew rate of CLKuWire, DATAuWire, and LEuWire should be at least 30 V/μs.
11
www.national.com
LMK03200 Family
Symbol
LMK03200 Family
Charge Pump Current Specification Definitions
30088731
I1 = Charge Pump Sink Current at VCPout = Vcc - ΔV
I2 = Charge Pump Sink Current at VCPout = Vcc/2
I3 = Charge Pump Sink Current at VCPout = ΔV
I4 = Charge Pump Source Current at VCPout = Vcc - ΔV
I5 = Charge Pump Source Current at VCPout = Vcc/2
I6 = Charge Pump Source Current at VCPout = ΔV
ΔV = Voltage offset from the positive and negative supply rails. Defined to be 0.5 V for this device.
Charge Pump Output Current Magnitude Variation vs. Charge Pump Output Voltage
30088732
Charge Pump Sink Current vs. Charge Pump Output Source Current Mismatch
30088733
Charge Pump Output Current Magnitude Variation vs. Temperature
30088734
www.national.com
12
LMK03200 Family
Typical Performance Characteristics (Note 16)
LVDS Vod
LVPECL Vod
30088708
30088707
LVDS Output Buffer Noise Floor (Note 17)
LVPECL Output Buffer Noise Floor (Note 17)
30088709
30088710
Delay Noise Floor (Notes 17, 18)
30088712
Note 16: These plots show performance at frequencies beyond what the part is guaranteed to operate at to give the user an idea of the capabilities of the part,
but they do not imply any sort of guarantee.
Note 17: To estimate this noise, only the output frequency is required. Divide value and input frequency are not integral.
Note 18: The noise of the delay block is independent of output type and only applies if the delay is enabled. The noise floor due to the distribution section
accounting for the delay noise can be calculated as: Total Output Noise = 10 × log(10Output Buffer Noise/10 + 10Delay Noise Floor/10).
13
www.national.com
LMK03200 Family
Refer to for a visual representation of what happens when
R15 is programmed.
1.0 Functional Description
The LMK03200 family of precision clock conditioners combine the functions of jitter cleaning/reconditioning, multiplication, and 0-delay distribution of a reference clock. The devices
integrate a Voltage Controlled Oscillator (VCO), a high performance Integer-N Phase Locked Loop (PLL), a partially
integrated loop filter, three LVDS, and five LVPECL clock output distribution blocks.
The devices include internal 3rd and 4th order poles to simplify loop filter design and improve spurious performance. The
1st and 2nd order poles are off-chip to provide flexibility for
the design of various loop filter bandwidths.
The VCO output is optionally accessible on the Fout port. Internally, the VCO output goes through a VCO divider to feed
the various clock distribution blocks.
Each clock distribution block includes a programmable divider, a phase synchronization circuit, a programmable delay,
a clock output mux, and an LVDS or LVPECL output buffer.
This allows multiple integer-related and phase-adjusted
copies of the reference to be distributed to eight system components.
The clock conditioners come in a 48-pin LLP package and are
footprint compatible with other clocking devices in the same
family.
1.1 BIAS PIN
To properly use the device, bypass Bias (pin 36) with a low
leakage 1 µF capacitor connected to Vcc. This is important
for low noise performance.
30088741
1.2 LDO BYPASS
To properly use the device, bypass LDObyp1 (pin 9) with a
10 µF capacitor and LDObyp2 (pin 10) with a 0.1 µF capacitor.
FIGURE 1. Frequency Calibration Routine Flowchart
1.5 LVDS/LVPECL OUTPUTS
By default all the clock outputs are disabled until programmed.
Each LVDS or LVPECL output may be disabled individually
by programming the CLKoutX_EN bits. All the outputs may
be disabled simultaneously by pulling the GOE pin low or
programming EN_CLKout_Global to 0.
The duty cycle of the LVDS and LVPECL clock outputs are
shown in the table below.
1.3 OSCILLATOR INPUT PORT (OSCin, OSCin*)
The purpose of OSCin is to provide the PLL with a reference
signal. Due to an internal DC bias the OSCin port should be
AC coupled, refer to the System Level Diagram in the Application Information section. The OSCin port may be driven
single-endedly by AC grounding OSCin* with a 0.1 µF capacitor.
1.4 LOW NOISE, FULLY INTEGRATED VCO
The LMK03200 family of devices contain a fully integrated
VCO. For proper operation the VCO uses a frequency calibration routine. The frequency calibration routine is activated
any time that the R15 register is programmed and
0_DELAY_MODE = 0. Once the frequency calibration routine
is run the temperature may not drift more than the maximum
allowable drift for continuous lock, ΔTCL, or else the VCO is
not guaranteed to stay in lock.
The status of the frequency calibration routine can be monitored. See section 2.2 Recommended Programing Sequence, with 0-Delay Mode
For the frequency calibration routine to work properly OSCin
must be driven by a valid signal and VCO_MUX = 0, otherwise
the resulting state is unknown.
www.national.com
14
VCO_DIV
CLKoutX_MUX
Duty
Cycle
Any
Divided, or Divided and Delayed
50%
2, 4, 6, 8
Any
50%
3
Bypassed, or Delayed
33%
5
Bypassed, or Delayed
40%
7
Bypassed, or Delayed
43%
1.7 CLKout OUTPUT STATES
Each clock output may be individually enabled with the
CLKoutX_EN bits. Each individual output enable control bit is
gated with the Global Output Enable input pin (GOE) and the
Global Output Enable bit (EN_CLKout_Global).
All clock outputs can be disabled simultaneously if the GOE
pin is pulled low by an external signal or EN_CLKout_Global
is set to 0.
CLKoutX
_EN bit
EN_CLKout
_Global bit
GOE pin
CLKoutX
Output State
1
1
Low
Low
Don't care
0
Don't care
Off
0
Don't care
Don't care
Off
1
1
High / No
Connect
Enabled
When an LVDS output is in the Off state, the outputs are at a
voltage of approximately 1.5 volts. When an LVPECL output
is in the Off state, the outputs are at a voltage of approximately
1 volt.
1.8 GLOBAL OUTPUT ENABLE AND LOCK DETECT
The GOE pin provides an internal pull-up resistor as shown
on the functional block diagram. If it is not terminated externally, the clock output states are determined by the Clock
Output
Enable
bits
(CLKoutX_EN)
and
the
EN_CLKout_Global bit.
By programming the PLL_MUX register to Digital Lock Detect
Active High, the Lock Detect (LD) pin can be connected to the
GOE pin in which case all outputs are set low automatically if
the synthesizer is not locked.
1.9 POWER ON RESET
When supply voltage to the device increases monotonically
from ground to Vcc, the power on reset circuit sets all registers
to their default values, see the programming section for more
information on default register values. Voltage should be applied to all Vcc pins simultaneously.
30088704
FIGURE 2. SYNC* Timing Diagram
The SYNC* pin provides an internal pull-up resistor as shown
on the functional block diagram. If the SYNC* pin is not terminated externally the clock outputs will operate normally. If
15
www.national.com
LMK03200 Family
the SYNC* function is not used, clock output synchronization
is not guaranteed. To ensure 0-delay to reference see section
2.2 Recommended Programing Sequence, with 0-Delay
Mode.
1.6 GLOBAL CLOCK OUTPUT SYNCHRONIZATION
The SYNC* pin synchronizes the clock outputs. SYNC* is not
used in VCO bypass mode. When the SYNC* pin is held in a
logic low state, the divided outputs are also held in a logic low
state. The bypassed outputs will continue to operate normally.
Shortly after the SYNC* pin goes high, the divided clock outputs are activated and will all transition to a high state simultaneously. All the outputs, divided and bypassed, will now be
synchronized. Clocks in the bypassed state are not affected
by SYNC* and are always synchronized with the divided outputs.
The SYNC* pin must be held low for greater than one clock
cycle of the output of the VCO divider, also known as the distribution path. Once this low event has been registered, the
outputs will not reflect the low state for four more cycles. This
means that the outputs will be low on the fifth rising edge of
the distribution path. Similarly once the SYNC* pin becomes
high, the outputs will not simultaneously transition high until
four more distribution path clock cycles have passed, which
is the fifth rising edge of the distribution path. See the timing
diagram in Figure 2 for further detail. The clocks are programmed as CLKout0_MUX = Bypassed, CLKout1_MUX =
Divided, CLKout1_DIV = 2, CLKout2_MUX = Divided, and
CLKout2_DIV = 4. To synchronize the outputs, after the low
SYNC* event has been registered, it is not required to wait for
the outputs to go low before SYNC* is set high.
LMK03200 Family
1.10 DIGITAL LOCK DETECT
The PLL digital lock detect circuitry compares the difference
between the phase of the inputs of the phase detector to a
RC generated delay of ε. To indicate a locked state the phase
error must be less than the ε RC delay for 5 consecutive reference cycles. Once in lock, the RC delay is changed to
approximately δ. To indicate an out of lock state, the phase
error must become greater δ. The values of ε and δ are shown
in the table below:
ε
10 ns
δ
20 ns
To utilize the digital lock detect feature, PLL_MUX must be
programmed for "Digital Lock Detect (Active High)" or "Digital
Lock Detect (Active Low)." When one of these modes is programmed the state of the LD pin will be set high or low as
determined by the description above as shown in Figure 3.
When the device is in power down mode and the LD pin is
programmed for a digital lock detect function, LD will show a
"no lock detected" condition which is low or high given active
high or active low circuitry respectively.
The accuracy of this circuit degrades at higher comparison
frequencies. To compensate for this, the DIV4 word should
be set to one if the comparison frequency exceeds 20 MHz.
The function of this word is to divide the comparison frequency presented to the lock detect circuit by 4.
30088705
FIGURE 3. Digital Lock Detect Flowchart
1.11 CLKout DELAYS
Each individual clock output includes a delay adjustment.
Clock output delay registers (CLKoutX_DLY) support a 150
ps step size and range from 0 to 2250 ps of total delay.
www.national.com
16
30088711
FIGURE 4. Global Lead and Lag
1.13 VCO DIVIDER BYPASS MODE
Once the LMK03200 is locked, the VCO divider may be bypassed to allow a higher frequency at the channel divider
inputs, which can be used to generate output frequencies not
allowable otherwise. The VCO_DIV bypass mode does not
work with 0-delay mode. See programming information in
sections 2.3 Recommended Programming Sequence, bypassing VCO divider and 2.4.5 VCO_MUX [1:0] -- VCO
Mux. SYNC* is not used when in VCO divider bypass mode.
1.14 0-DELAY MODE
The LMK03200 family can feedback an output to the phase
detector either internally using CLKout5 or CLKout6, or externally by routing any clock output back to the FBCLKin/
FBCLKin* input port to be synchronized with the reference
clock for 0-delay output.
To ensure 0-delay for all the outputs, the lowest frequency
output must be feed back to the PLL. This requirement forces
the maximum phase detector frequency ≤ the minimum clock
output frequency.
When CLKout5 or CLKout6 is used for feedback internally,
CLKout5 or CLKout6 are still valid for regular clocking applications. If CLKout5 or CLKout6 are unused, they do not need
to be externally terminated, by not terminating the output
power consumption is reduced.
To engage the 0-delay mode, refer to programming instructions in section 2.2 Recommended Programing Sequence,
with 0-Delay Mode.
Figure 5 illustrates the 0-delay mode programming sequence.
More detail is in section 2.2 Recommended Programing Sequence, with 0-Delay Mode
30088742
FIGURE 5. Outline of 0-delay mode programming
sequence
The 0-delay mode may not be used together with the
VCO_DIV bypass except for the purpose of being temporarily
enabled to re-program the PLL_N to keep the PLL in lock. See
2.3 Recommended Programming Sequence, bypassing VCO
divider for more information.
17
www.national.com
LMK03200 Family
alter the phase of the various clock outputs. This is not shown
in Figure 4. Note that Figure 4 illustrates use of PLL_N_DLY
and PLL_R_DLY to shift clock outputs to lead or lag the reference input phase. It doesn't reflect exact timing or account
for delays in buffers internal to the device, meaning the clock
output is not guaranteed to have 0 phase delay from the reference input to a clock output as shown at the pins of the
device.
1.12 GLOBAL DELAYS
After the N divider and R divider are two delays PLL_N_DLY
and PLL_R_DLY. They support a 150 ps step size and range
from 0 to 2250 ps of total delay. When using the 0-delay
mode, these delays can be used to cause the clock outputs
to lead or lag the clock input phase. Figure 4 illustrates the
use of the global delays. Note, it is possible to use the individual delays on each clock output (CLKoutX_DLY) to further
LMK03200 Family
0_DELAY_MODE. Otherwise a separate SYNC* is
required ensure all outputs are synchronized together
after all steps are completed.
• Program R0 with the reset bit set (RESET = 1). This
ensures the device is in a default state. When the reset bit
is set in R0, the other R0 bits are ignored.
— If R0 is programmed again, the reset bit is programmed
clear (RESET = 0).
• Program R0 to R7 as necessary with desired clocks with
appropriate enable, mux, divider, and delay settings.
Outputs being used should be enabled.
— R0: DLD_MODE2 = 1 (Digital Lock Detect is now
Frequency Calibration Routine Complete)
— R0: 0_DELAY_MODE = 0
— R0: FB_MUX = desired feedback path for 0-delay
mode.
— RX: CLKoutX_EN = 1 for used clock outputs.
• Program R8 for optimum phase noise performance.
• Program R9 with Vboost setting if necessary.
• Program R11 with DIV4 setting if necessary.
• Program R13 with oscillator input frequency and internal
loop filter values.
• Program R14 with Fout enable bit, global clock output bit,
power down setting, PLL mux setting, PLL_R divider, and
global PLL R delay.
— R14: EN_CLKout_Global = 1
— R14: PLL_MUX = 3 or 4 for frequency calibration
routine complete signal.
• Program R15 with PLL charge pump gain, VCO divider,
PLL N divider, and global PLL N delay. The frequency
calibration routine starts.
Now the LD pin should be monitored for the frequency calibration routine completed signal to be asserted if PLL_MUX
was set to 3 or 4 and DLD_MODE2 = 1. Otherwise wait 2 ms
for the frequency calibration routine to complete. Once the
frequency calibration routine is completed step 2 may be executed to achieve 0-delay mode. With the addition of the clock
output divide in the feedback path, the total N feedback divide
will change and the device will need to be programmed in this
step to accommodate this extra divide.
2.0 General Programming
Information
The LMK03200 family of devices are programmed using several 32-bit registers which control the device's operation. The
registers consist of a data field and an address field. The last
4 register bits, ADDR [3:0] form the address field. The remaining 28 bits form the data field DATA [27:0].
During programming, LEuWire is low and serial data is
clocked in on the rising edge of CLKuWire (MSB first). When
LE goes high, data is transferred to the register bank selected
by the address field. Only registers R0 to R8, R11, and R13
to R15 need to be programmed for proper device operation.
For the frequency calibration routine to work properly OSCin
must be driven by a valid signal when R15 is programmed.
Any changes to the PLL_R divider or OSCin require R15 to
be programmed again while 0_DELAY_MODE = 0 to activate
the frequency calibration routine.
2.1 Recommended Programming Sequence, without 0Delay Mode
The recommended programming sequence involves programming R0 with the reset bit set (RESET = 1) to ensure the
device is in a default state. It is not necessary to program R0
again, but if R0 is programmed again, the reset bit is programmed clear (RESET = 0). Registers are programmed in
order with R15 being the last register programmed. An example programming sequence is shown below.
• Program R0 with the reset bit set (RESET = 1). This
ensures the device is in a default state. When the reset bit
is set in R0, the other R0 bits are ignored.
— If R0 is programmed again, the reset bit is programmed
clear (RESET = 0).
• Program R0 to R7 as necessary with desired clocks with
appropriate enable, mux, divider, and delay settings.
• Program R8 for optimum phase noise performance.
• Program R9 with Vboost setting if necessary.
• Program R11 with DIV4 setting if necessary.
• Program R13 with oscillator input frequency and internal
loop filter values.
• Program R14 with Fout enable bit, global clock output bit,
power down setting, PLL mux setting, and PLL_R divider.
• Program R15 with PLL charge pump gain, VCO divider,
and PLL N divider. The frequency calibration routine
starts.
Step 2
• Program R0 with the same settings as in step 1 except:
— 0_DELAY_MODE = 1 to activate 0-delay mode.
• The output being used for feedback must be enabled for
the device to lock. This means that...
— GOE pin is high. (set high if low from step 1).
— SYNC* pin is high.
— CLKoutX_EN bit is 1. (For all clocks being used)
— EN_CLKout_Global bit is 1.
• Special feedback cases:
— When CLKout 5 is used for feedback, CLKout 6 must
also be enabled (CLKout6_EN = 1). The configuration
of the channel does not matter.
— When FBCLKin/FBCLKin* is used for feedback,
CLKout 5 and CLKout 6 must be enabled
(CLKout5_EN = 1 and CLKout6_EN = 1). The
configuration of the channels does not matter, except
when CLKout 5 or CLKout 6 is the source channel
which drives FBCLKin/FBCLKin*.
• Program R15 with new PLL_N value.
The device will now synchronize clock outputs with reference
input. As soon as the device is settled the LD pin will be as-
2.2 Recommended Programing Sequence, with 0-Delay
Mode
The lock procedure when using the 0-delay mode has two
steps. The first is to complete the frequency calibration routine
for the target frequency while not in 0-delay mode. The second step is to activate 0-delay mode and re-program the
PLL_N divider to accommodate the additional divide in the
clock output path so that phase lock can be achieved with the
reference input clock.
Global_CLK_EN and each output being used should be enabled in step 1. If the user desires for no output from the clock
outputs during frequency lock, the GOE pin should be held
low.
Step 1
• GOE pin is held low to keep outputs from toggling.
Disabling the clock output with MICROWIRE should not
be used so that when more than one clock output is used,
they will all be synchronized together when using
www.national.com
18
Step 2
• Set GOE pin high.
• Program Register 0
RESET = 0
0_DELAY_MODE = 1 (activate 0-delay mode)
DLD_MODE2 = 1 (same, don't care)
FB_MUX = 0 (same)
• Program Register 15 (VCO Frequency = 1200 MHz)
PLL_N = 3 (updated value)
VCO_DIV = 2 (same)
PLL_CP_GAIN = Loop filter dependant
The device will now synchronize. As soon as the device is
settled the LD pin will go high to indicate the device is phase
locked (0_DELAY_MODE = 1 reverts the LD pin back to digital lock detect mode). Now the device's VCO will be locked
to 1200 MHz with an output clock of 30 MHz.
2.2.2 0-Delay Mode Example 2
In this example assume the user requirements are: an input
reference of 61.44 MHz and clock outputs of 12.288 MHz
(CLKout6), 30.72 MHz (CLKout3), and 61.44 MHz (CLKout4)
with the clock outputs synchronized to the reference input
clock. CLKout6 is chosen for feedback since the 12.288 MHz
clock is the lowest frequency required to be synchronized (0delay) with the reference and therefore must be fed back to
the PLL N divider, note this also limits the phase detector frequency to 12.288 MHz so the input reference must be divided
down to 12.288 MHz. If the 12.288 MHz clock wasn't required
to be in synchronization (0-delay) with the reference, the
30.72 MHz clock could have been fed back instead rasing the
maximum allowable phase detector frequency to 30.72 MHz.
Registers which are not explicitly programmed are set to default values.
2.2.1 0-Delay Mode Example 1
In this example assume the user requirements are: an input
reference of 10 MHz and a clock output of 30 MHz with the
clock output synchronized to the reference input clock. CLKout5 is chosen as the output clock because it allows internal
feedback for the 0-delay mode.
Registers which are not explicitly programmed are set to default values.
Step 1
• GOE pin is set low.
• Program Register 0 (reset device)
RESET = 1
Other values don't matter
• Program Register 0 again.
RESET = 0
DLD_MODE2 = 1 (Digital Lock detect will be used for
monitoring frequency calibration routine complete)
FB_MUX = 0 (CLKout5 feedback)
• Program Register 5 (30 MHz, used for feedback)
CLKout5_EN = 1 (turn output on)
CLKout5_MUX = 1 (divided)
CLKout5_DIV = 10 (divide by 20)
• Program Register 6 (Must be enabled when using
CLKout5 for feedback)
CLKout6_EN = 1 (turn output on)
• Program Register 8
• Program Register 14
PLL_R = 1 (Phase detector frequency = 10 MHz)
PLL_MUX = 3 (DLD Active High)
• Program Register 15 (VCO Frequency = 1200 MHz)
PLL_N = 60
VCO_DIV = 2
PLL_CP_GAIN = Loop filter dependant
• Begin monitoring LD pin for frequency calibration routine
complete signal.
The device now begins the frequency calibration routine,
when it completes the LD pin will go high since PLL_MUX was
programmed with the active high option for the frequency calibration routine complete signal. When the LD pin goes high,
step 2 is executed.
Step 1
• GOE pin is set low.
• Program Register 0 (reset device)
RESET = 1
Other values don't matter
• Program Register 0 again.
RESET = 0
DLD_MODE2 = 1 (Digital Lock detect will be used for
monitoring frequency calibration routine complete)
FB_MUX = 2 (CLKout6 feedback)
• Program Register 3 (30.72 MHz)
CLKout3_EN = 1 (turn output on)
CLKout3_MUX = 1 (divided)
CLKout3_DIV = 10 (divide by 20)
• Program Register 4 (61.44 MHz)
CLKout4_EN = 1 (turn output on)
CLKout4_MUX = 1 (divided)
CLKout4_DIV = 5 (divide by 10)
• Program Register 6 (12.288 MHz, used for feedback)
CLKout6_EN = 1 (turn output on)
CLKout6_MUX = 1 (divided)
CLKout6_DIV = 25 (divide by 50)
• Program Register 8
• Program Register 14
PLL_R = 5 (Phase detector frequency = 12.288 MHz)
PLL_MUX = 3 (DLD Active High)
• Program Register 15 (VCO Frequency = 1228.8 MHz)
PLL_N = 50
VCO_DIV = 2
PLL_CP_GAIN = Loop filter dependant
19
www.national.com
LMK03200 Family
serted active high or low depending on PLL_MUX value to
indicate the device is phase locked. 0_DELAY_MODE = 1
reverts the LD pin back to digital lock detect.
The device is now phase locked and synchronized with the
reference clock. Since step 2 requires GOE high for feedback,
it is possible that the clock outputs will be momentarily slightly
off frequency while the dividers and or feedback paths are
being changed. Also when GOE is set high, it is possible for
a runt pulse to occur since GOE is an asynchronous input. If
there is no concern for off frequency clock cycles then it is
allowable to leave GOE high for the entire programming procedure.
Before 0-delay mode the VCO frequency equation is: VCO
Frequency = Reference OSCin Frequency / PLL R Divider *
PLL N Divider * VCO divider.
After 0-delay mode the VCO frequency equation is: VCO Frequency = Reference OSCin Frequency / PLL R Divider * PLL
N Divider * VCO divider * CLKoutX_DIV. Where
CLKoutX_DIV is the divide value of the clock used for feedback. If the clock is from FBCLKin, any external divides must
also be accounted for.
LMK03200 Family
•
frequency calibration routine is completed step 2 may be executed to bypass the VCO divider.
Begin monitoring LD pin for frequency calibration routine
complete signal.
The device now begins the frequency calibration routine,
when it completes the LD pin will go high since PLL_MUX was
programmed with the active high option for the frequency calibration routine complete signal. When the LD pin goes high,
step 2 is executed.
Step 2
• Program R0 with the same settings as step 1 except:
— DLD_MODE2 = 0 (Digital lock detect is normal)
— 0_DELAY_MODE = 1 (temporarily enable 0-delay
mode)
0_DELAY_MODE is not to be used in VCO divider
bypass mode. It is only activated briefly to prevent the
frequency calibration routine from running when R15 is
programmed while the VCO Mux is selecting the VCO
Output directly.
• Program R7
— VCO_MUX = 2 (VCO output)
• Program R14 with PLL_MUX as desired, or PLL_MUX =
3 or 4 for Lock Detect.
• Program R15 with the updated PLL_N value since the
VCO divider is no longer in the feedback path. The
updated value of PLL_N = Old PLL_N * VCO_Divider
value. This programs the VCO to the same frequency as
step 1. The VCO must be programmed for the same
frequency as step 1.
• Program R0 with the same settings except:
— 0_DELAY_MODE = 0 (disable 0-delay mode)
Step 2
• GOE pin is set high.
• Program Register 0
RESET = 0
0_DELAY_MODE = 1 (activate 0-delay mode)
DLD_MODE2 = 1 (same, don't care)
FB_MUX = 2 (CLKout6 feedback)
• Program Register 15 (VCO Frequency = 1228.8 MHz)
PLL_N = 1 (updated value)
VCO_DIV = 2 (don't care)
PLL_CP_GAIN = Loop filter dependant
The device will now synchronize. As soon as the device is
settled the LD pin will go high to indicate the device is phase
locked (0_DELAY_MODE = 1 reverts the LD pin back to digital lock detect). Now the device's VCO will be locked to
1228.8 MHz with the output clocks of 12.288, 30.72, and
61.44 MHz.
2.3 Recommended Programming Sequence, bypassing
VCO divider
The programming procedure when using the VCO mux to bypass the VCO divider has two steps. The first step runs the
frequency calibration routine with the VCO divider in the feedback path. The second step bypasses the VCO divider and
locks the PLL.
After a short settling time, the VCO will be locked and the
clock outputs will be at the desired frequency. The LD pin will
indicate when the PLL is locked if PLL_MUX is programmed
to a digital lock detect mode.
2.3.1 VCO divider bypass example
In this example assume the user requirements are: an input
reference of 61.44 MHz and clock output frequencies of 614.4
MHz on CLKout0 and CLKout1, and 307.2 MHz on CLKout2.
The VCO is programmed to 1228.8 MHz.
Registers not explicitly programmed are set to default values.
Step 1
• Program R0 with the reset bit set (RESET = 1). This
ensures the device is in a default state. When the reset bit
is set in R0, the other R0 bits are ignored.
— If R0 is programmed again, the reset bit is programmed
clear (RESET = 0).
• Program R0 to R7 as necessary with desired clocks with
appropriate enable, mux, divider, and delay settings.
— The outputs should be programmed with divider values
which achieve desired output frequencies after the
VCO divider has been bypassed.
— R0: DLD_MODE2 = 1 (Digital Lock Detect is now
Frequency Calibration Routine Complete)
— R7: VCO_MUX = 0 (VCO divider output, default)
• Program R8 for optimum phase noise performance.
• Program R9 with Vboost setting if necessary.
• Program R11 with DIV4 setting if necessary.
• Program R13 with oscillator input frequency and internal
loop filter values.
• Program R14 with Fout enable bit, global clock output bit,
power down setting, PLL mux setting, and PLL_R divider.
— R14: PLL_MUX = 3 or 4 for frequency calibration
routine complete signal.
• Program R15 with PLL charge pump gain, VCO divider,
and PLL N divider. The frequency calibration routine
starts.
Now the LD pin should be monitored for the frequency calibration routine completed signal to be asserted if PLL_MUX
was set to 3 or 4 and DLD_MODE2 = 1. Otherwise wait 2 ms
for the frequency calibration routine to complete. Once the
www.national.com
Step 1
• GOE pin is set high
• Program Register 0 (reset device)
RESET = 1
Other values don't matter
• Program Register 0 again (614.4 MHz)
DLD_MODE2 = 1 (Digital Lock detect will be used for
monitoring frequency calibration routine complete)
CLKout0_EN = 1 (turn output on)
CLKout0_MUX = 0 (bypassed)
• Program Register 1 (614.4 MHz)
CLKout1_EN = 1 (turn output on)
CLKout1_MUX = 0 (bypassed)
• Program Register 2 (307.2 MHz)
CLKout2_EN = 2 (turn output on)
CLKout2_MUX = 1 (divide)
CLKout2_DIV = 1 (divide by 2)
• Program Register 8
• Program Register 14
PLL_R = 2 (Phase detector frequency = 30.72 MHz)
PLL_MUX = 3 (DLD Active High, now frequency
calibration routine complete)
Program Register 15 (VCO Frequency = 1228.8 MHz)
PLL_N = 20
VCO_DIV = 2
PLL_CP_GAIN = Loop filter dependant
• Begin monitoring LD pin lock detect.
20
LMK03200 Family
The device now beings the frequency calibration routine,
when it completes the LD pin will go high since PLL_MUX was
programmed with the active high option for lock detect and
DLD_MODE2 = 1. When the LD pin goes high, or after 2 ms
have passed (the time for frequency calibration routine to
complete), step 2 is executed. Note that VCO_DIV = 0 was
not programmed to select VCO Divider since that is the default mode.
At this time the clock output frequency will be half the final
value because VCO_DIV = 2. If VCO_DIV was = 3, the clock
output frequencies would be a third the final value, etc.
Step 2
• Program Register 0
DLD_MODE2 = 0 (Digital lock detect is normal)
0_DELAY_MODE = 1 (active 0-delay mode so that
programming R15 won't start frequency calibration
routine)
CLKout0_EN = 1 (keep same programming)
CLKout0_MUX = 0 (keep same programming)
• Program Register 7
VCO_MUX = 2 (bypass VCO divider)
• Program Register 15 (VCO Frequency = 1228.8 MHz)
PLL_N = 40 (VCO_DIV bypassed, must update PLL_N)
• Program Register 0
0_DELAY_MODE = 0
CLKout0_EN = 1 (keep same programming)
CLKout0_MUX = 0 (keep same programming)
When R7 is updated to bypass the VCO divider the PLL will
loose lock until R15 can be updated again with the updated
PLL_N divider value.
Once the LD pin goes high again, the clock outputs will be
locked at 614.4 MHz and 307.2 MHz.
21
www.national.com
www.national.com
0
0
0
0
R4
R5
R6
R7
0
R2
0
0
R1
22
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
27
28
DLD_MODE2
R3
0
R0
29
0_DELAY_
MODE
0
30
31
RESET
Register
2.4 Register Map
25
0
VCO
_MUX
[1:0]
0
0
0
0
0
0
0
0
0
0
0
0
24
0
0
0
0
0
0
0
FB_MUX
[1:0]
26
0
0
0
0
0
0
0
0
23
0
0
0
0
0
0
0
0
22
0
0
0
0
0
0
0
0
21
0
0
0
0
0
0
0
0
20
0
0
0
0
0
0
0
0
19
17
CLKout7
_MUX
[1:0]
CLKout6
_MUX
[1:0]
CLKout5
_MUX
[1:0]
CLKout4
_MUX
[1:0]
CLKout3
_MUX
[1:0]
CLKout2
_MUX
[1:0]
CLKout1
_MUX
[1:0]
CLKout0
_MUX
[1:0]
Data [27:0]
18
16
CLKout0_EN CLKout1_EN CLKout2_EN CLKout3_EN CLKout4_EN CLKout5_EN CLKout6_EN CLKout7_EN
15
14
13
11
CLKout7_DIV
[7:0]
CLKout6_DIV
[7:0]
CLKout5_DIV
[7:0]
CLKout4_DIV
[7:0]
CLKout3_DIV
[7:0]
CLKout2_DIV
[7:0]
CLKout1_DIV
[7:0]
CLKout0_DIV
[7:0]
12
10
9
8
7
5
CLKout7_DLY
[3:0]
CLKout6_DLY
[3:0]
CLKout5_DLY
[3:0]
CLKout4_DLY
[3:0]
CLKout3_DLY
[3:0]
CLKout2_DLY
[3:0]
CLKout1_DLY
[3:0]
CLKout0_DLY
[3:0]
6
4
0
0
0
0
0
0
0
1
1
1
1
0
0
0
0
A2
A3
0
2
3
1
1
0
0
1
1
0
0
A1
1
1
0
1
0
1
0
1
0
A0
0
LMK03200 Family
1
0
0
0
PLL_
CP_
GAIN
[1:0]
R9
R11
R13
R14
R15
0
0
0
0
1
0
29
EN_CLKout_Global
EN_Fout
VCO_DIV
[3:0]
0
0
0
1
0
0
1
1
0
0
0
0
0
0
23
24
25
0
0
0
0
26
0
0
0
0
27
POWERDOWN
0
0
0
1
28
0
0
0
21
PLL_MUX
[3:0]
0
0
0
0
22
0
0
0
20
0
0
0
0
0
0
18
1
1
0
17
0
PLL_N
[17:0]
PLL_R
[11:0]
0
1
0
0
0
0
13
14
0
15
0
16
OSCin_FREQ
[7:0]
19
Vboost
0
0
0
0
0
Register
R8
30
31
DIV4
23
VCO_
R4_LF
[2:0]
0
0
0
12
0
1
1
11
0
0
0
10
VCO_
R3_LF
[2:0]
0
1
0
9
0
0
1
8
0
0
0
7
0
0
0
5
PLL_N_DLY
[3:0]
PLL_R_DLY
[3:0]
VCO_
C3_C4_LF
[3:0]
0
0
0
6
0
0
0
4
1
1
1
1
1
1
3
1
1
1
0
0
0
2
1
1
0
1
0
0
1
1
0
1
1
1
0
0
LMK03200 Family
0
www.national.com
LMK03200 Family
from these, the functions of these bits in registers R0 through
R7 are identical. The X in CLKoutX_MUX, CLKoutX_DIV,
CLKoutX_DLY, and CLKoutX_EN denote the actual clock
output which may be from 0 to 7.
2.4 Register R0 to R7
Registers R0 through R7 control the eight clock outputs. Register R0 controls CLKout0, Register R1 controls CLKout1, and
so on. There are some additional bit in register R0 called RESET, DLD_MODE2, 0_DELAY_MODE, and FB_MUX. Aside
Default Register Settings after Power on Reset
Bit Name
Default
Bit Value
Bit State
Bit Description
Register
Bit
Location
RESET
0
No reset, normal operation
Reset to power on defaults
DLD_MODE2
0
Disabled
Digital Lock Detect Mode2 is disabled
0_DELAY_MODE
0
Disabled
Not 0-delay mode
FB_MUX
0
CLKout5
0-delay mode feedback
26:25
CLKoutX_MUX
0
Bypassed
CLKoutX mux mode
18:17
CLKoutX_EN
0
Disabled
CLKoutX enable
CLKoutX_DIV
1
Divide by 2
CLKoutX clock divide
CLKoutX_DLY
0
0 ps
CLKoutX clock delay
VCO_MUX
0
Use VCO divider
VCO divider bypassed mode
R7
26:25
Vboost
0
Normal Mode
Output Power Control
R9
16
DIV4
0
PDF ≤ 20 MHz
Phase Detector Frequency
R11
OSCin_FREQ
10
10 MHz OSCin
OSCin Frequency in MHz
VCO_R4_LF
0
Low (~200 Ω)
R4 internal loop filter values
VCO_R3_LF
0
Low (~600 Ω)
R3 internal loop filter values
VCO_C3_C4_LF
0
C3 = 0 pF, C4 = 10 pF
C3 and C4 internal loop filter values
7:4
EN_Fout
0
Fout disabled
Fout enable
28
EN_CLKout_Global
1
Normal - CLKouts normal
Global clock output enable
27
POWERDOWN
0
Normal - Device active
Device power down
PLL_MUX
0
Disabled
Multiplexer control for LD pin
PLL_R
10
R divider = 10
PLL R divide value
19:8
PLL_R_DLY
0
0 ps
PLL R delay value (lag)
7:4
PLL_CP_GAIN
0
100 µA
Charge pump current
VCO_DIV
2
Divide by 2
VCO divide value
N divider = 760
PLL N divide value
0 ps
PLL N delay value (lead)
PLL_N
PLL_N_DLY
760
0
2.4.1 Reset bit -- Reset device to power on defaults
This bit is only in register R0. The use of this bit is optional
and it should be set to '0' if not used. Setting this bit to a '1'
forces all registers to their power on reset condition and therefore automatically clears this bit. If this bit is set, all other R0
bits are ignored and R0 needs to be programmed again if
used with its proper values and RESET = 0.
www.national.com
31
R0
R0 to R7
28
27
16
15:8
7:4
15
21:14
R13
R14
13:11
10:8
26
23:20
31:30
R15
29:26
25:8
7:4
2.4.2 DLD_MODE2 bit -- Digital Lock Detect Mode 2
This bit is only in register R0. The output of the LD pin is defined by register PLL_MUX (See 2.9.2 PLL_MUX[3:0] -- Multiplexer Control for LD Pin). When a Digital Lock Detect output
is selected, setting this bit overrides the default functionality
allowing the user to determine when the frequency calibration
routine is done. When using 0-delay mode this informs the
user when the 0-delay mode can be activated. See section
2.2 Recommended Programing Sequence, with 0-Delay
Mode for more information.
24
DLD_MODE2
0_DELAY_MODE
LD Output
0 (default)
X
Digital Lock Detect
1
0
Digital Calibration
Complete
1
1
Digital Lock Detect
0_DELAY_MODE
Frequency
Calibration
Routine
N divider mux
(Ndiv Mux)
0 (default)
Enabled
VCO Divider
1
Disabled
Feedback Mux
(FB_MUX)
2.4.4 FB_MUX [1:0] -- Feedback Mux
This bit is only in register R0 and is for use with the 0-delay
mode.
FB_MUX [1:0]
Mode
0
CLKout5 (default)
1
FBCLKin/FBCLKin* Input
2
CLKout6
3
Reserved
CLKout5_EN
(See 2.4.9)
CLKout6_EN
(See 2.4.9)
CLKout 5
1
1
FBCLKin/
FBCLKin*
1
1
CLKout 6
Don't care
1
Mode
0
VCO Divider (default)
1
Reserved
2
VCO
3
Reserved
2.4.6 CLKoutX_MUX [1:0] -- Clock Output Multiplexers
These bits control the Clock Output Multiplexer for each clock
output. Changing between the different modes changes the
blocks in the signal path and therefore incurs a delay relative
to the bypass mode. The different MUX modes and associated delays are listed below.
When using CLKout5 and FBCLKin/FBCLKin* for feedback
for 0-delay mode, the proper clock outputs must be enabled
to pass the feedback signal back to the N divider. Refer to the
table below for more details. The only requirement given by
the table below is that the clock output must be enabled with
CLKoutX_EN bits, if the clock is only used for feedback, the
clock does not need to be terminated which saves power. The
simplest feedback path to use is CLKout6 since it does not
require another CLKout to be enabled.
Clock Feedback
Source
VCO_MUX [1:0]
CLKoutX_MUX
[1:0]
Mode
Added Delay Relative
to Bypass Mode
0
Bypassed
(default)
0 ps
1
Divided
100 ps
2
Delayed
400 ps
(In addition to the
programmed delay)
3
Divided and
Delayed
500 ps
(In addition to the
programmed delay)
The electrical specification td0-DELAY is given with the condition FB_MUX = 0 (CLKout5). If FB_MUX = 2 (CLKout6), then
td0-DELAY, OSCin to CLKoutX 0-delay, increases 100 ps.
25
www.national.com
LMK03200 Family
2.4.5 VCO_MUX [1:0] -- VCO Mux
This bit is only in register R7 and is used to select either the
VCO divider output or the VCO output for the clock distribution
path. By selecting the VCO output (VCO_MUX=2), the VCO
divider is bypassed allowing a higher frequency at the channel
divider inputs, which can be used to generate output frequencies not allowable otherwise.
Important: The VCO calibration routine requires that the VCO
divider (VCO_MUX = 0) is selected when programming R15.
The VCO divider (VCO_MUX=0) must be selected for the
VCO calibration routine to operate properly.
Important: When bypassing the VCO divider (VCO_MUX=2),
0-delay mode may not be used. However 0_DELAY_MODE
is set to 1 when re-programming PLL_N after the VCO divider
has been bypassed to prevent the frequency calibration routine from running. The new PLL_N value = Old PLL_N * VCO
divider. Once PLL_N is re-programmed 0_DELAY_MODE is
set back to 0. See the programming section, 2.3 Recommended Programming Sequence, bypassing VCO divider, for
more information.
2.4.3 0_DELAY_MODE bit -- Activate 0-Delay Mode
This bit is only in register R0 and is used for activating the 0delay mode. Once the frequency calibration routine is complete - as determined by monitoring the LD output in
DLD_MODE2 or waiting 2 ms after programming R15, this bit
may be set to activate 0-delay mode. Setting this bit sets the
N divider mux to use the feedback mux for input and prevents
the frequency calibration routine from activating when register
R15 is programmed. Once this bit is set and the 0-delay path
is completed, the PLL_N divider in register R15 will need to
be reprogrammed for final phase lock. See section 2.2 Recommended Programing Sequence, with 0-Delay Mode for
more information. Also refer to 2.4.4 FB_MUX [1:0] -- Feedback Mux for more information on proper configuration of the
device for feedback of the selected signal.
LMK03200 Family
2.4.9 CLKoutX_EN bit -- Clock Output Enables
These bits control whether an individual clock output is enabled or not. If the EN_CLKout_Global bit is set to zero or if
GOE pin is held low, all CLKoutX_EN bit states will be ignored
and all clock outputs will be disabled.
2.4.7 CLKoutX_DIV [7:0] -- Clock Output Dividers
These bits control the clock output divider value. In order for
these dividers to be active, the respective CLKoutX_MUX bit
must be set to either "Divided" or "Divided and Delayed"
mode. After all the dividers are programed, the SYNC* pin
must be used to ensure that all edges of the clock outputs are
aligned. The Clock Output Dividers follow the VCO Divider so
the final clock divide for an output is VCO Divider × Clock
Output Divider. By adding the divider block to the output path
a fixed delay of approximately 100 ps is incurred.
The actual Clock Output Divide value is twice the binary value
programmed as listed in the table below.
CLKoutX_EN
bit
0
0
0
0
0
0
0
0
0
Invalid
0
0
0
0
0
0
0
1
2 (default)
0
0
0
0
0
0
1
0
4
0
0
0
0
0
0
1
1
6
0
0
0
0
0
1
0
0
8
0
0
0
0
0
1
0
1
10
.
.
.
.
.
.
.
.
...
1
1
1
1
1
1
1
1
510
Delay (ps)
0
0 (default)
1
150
2
300
3
450
4
600
5
750
www.national.com
6
900
7
1050
8
1200
9
1350
10
1500
11
1650
12
1800
13
1950
14
2100
15
2250
Disabled
(default)
Enabled
2.5 Register R8
There are no user programmable bits in register R8. Register
R8 is programmed as shown in the section for optimum phase
noise performance.
2.6 Register R9
The programming of register R9 is optional. If it is not programmed the bit Vboost will be defaulted to 0, which is the
test condition for all electrical characteristics.
2.6.1 Vboost bit -- Voltage Boost
By enabling this bit, the voltage output levels for all clock outputs is increased. Also, the noise floor is improved
2.4.8 CLKoutX_DLY [3:0] -- Clock Output Delays
These bits control the delay stages for each clock output. In
order for these delays to be active, the respective
CLKoutX_MUX bit must be set to either "Delayed" or "Divided
and Delayed" mode. By adding the delay block to the output
path a fixed delay of approximately 400 ps is incurred in addition to the delay shown in the table below.
CLKoutX_DLY [3:0]
EN_CLKout_Global bit = 1
GOE pin = High / No
Connect
1
Clock Output
Divider value
CLKoutX_DIV [7:0]
CLKoutX
State
Conditions
26
Vboost
Typical LVDS
Voltage Output
(mV)
Typical LVPECL
Voltage Output
(mV)
0
350
810
1
390
865
2.8.3 VCO_R4_LF [2:0] -- Value for Internal Loop Filter
Resistor R4
These bits control the R4 resistor value in the internal loop
filter. The recommended setting for VCO_R4_LF[2:0] = 0 for
optimum phase noise and jitter.
2.7.1 DIV4 -- High Phase Detector Frequencies and Lock
Detect
This bit divides the frequency presented to the digital lock detect circuitry by 4. It is necessary to get a reliable output from
the digital lock detect output in the case of a phase detector
frequency greater than 20 MHz.
DIV4
0
R4 Value (kΩ)
0
Low (~200 Ω) (default)
1
10
2
20
3
30
Digital Lock Detect Circuitry Mode
4
40
Not divided
5 to 7
Invalid
Phase Detector Frequency ≤ 20 MHz (default)
2.8.4 OSCin_FREQ [7:0] -- Oscillator Input Calibration
Adjustment
These bits are to be programmed to the OSCin frequency. If
the OSCin frequency is not an integral multiple of 1 MHz, then
round to the closest value.
Divided by 4
Phase Detector Frequency > 20 MHz
1
VCO_R4_LF[2:0]
2.8 Register R13
OSCin_FREQ [7:0]
OSCin Frequency
1
1 MHz
2
2 MHz
...
...
Loop Filter Capacitors
10
10 MHz (default)
VCO_C3_C4_LF [3:0]
C3 (pF)
C4 (pF)
...
...
0
0 (default)
10 (default)
200
200 MHz
1
0
60
201 to 255
Invalid
2
50
10
3
0
110
4
50
110
5
100
110
6
0
160
7
50
160
8
100
10
9
100
60
10
150
110
0
0
0
0
0
0
0
0
0
0
0
0
Invalid
11
150
60
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
0
0
0
0
0
0
0
0
1
0
2
.
.
.
.
.
.
.
.
.
.
.
.
...
0
0
0
0
0
0
0
0
1
0
1
0
10 (default)
.
.
.
.
.
.
.
.
.
.
.
.
...
1
1
1
1
1
1
1
1
1
1
1
1
4095
2.8.1 VCO_C3_C4_LF [3:0] -- Value for Internal Loop Filter
Capacitors C3 and C4
These bits control the capacitor values for C3 and C4 in the
internal loop filter.
12 to 15
2.9 Register R14
2.9.1 PLL_R [11:0] -- R Divider Value
These bits program the PLL R Divider and are programmed
in binary fashion. Any changes to PLL_R require R15 to be
programmed again while 0_DELAY_MODE = 0 to active the
frequency calibration routine.
Invalid
2.8.2 VCO_R3_LF [2:0] -- Value for Internal Loop Filter
Resistor R3
These bits control the R3 resistor value in the internal loop
filter. The recommended setting for VCO_R3_LF[2:0] = 0 for
optimum phase noise and jitter.
VCO_R3_LF[2:0]
R3 Value (kΩ)
0
Low (~600 Ω) (default)
1
10
2
20
3
30
4
40
5 to 7
Invalid
PLL R Divide
Value
PLL_R [11:0]
27
www.national.com
LMK03200 Family
2.7 Register R11
This register only has one bit and only needs to be programmed in the case that the phase detector frequency is
greater than 20 MHz and digital lock detect is used. Otherwise, it is automatically defaulted to the correct values.
LMK03200 Family
2.9.2 PLL_MUX[3:0] -- Multiplexer Control for LD Pin
These bits set the output mode of the LD pin. The table below
lists several different modes. Note that PLL_MUX = 3 and
PLL_MUX = 4 have alternate functionality if DLD_MODE2
(section 2.4.2 DLD_MODE2 bit -- Digital Lock Detect Mode
2) is set.
PLL_MUX [3:0]
Output Type
LD Pin Function
0
Hi-Z
Disabled (default)
1
Push-Pull
Logic High
2
Push-Pull
Logic Low
Push-Pull
Digital Lock Detect
(Active High)
(Note 19)
Push-Pull
Digital Lock Detect
(Active Low)
(Note 20)
3
4
5
Push-Pull
Analog Lock Detect
6
Open Drain
NMOS
Analog Lock Detect
7
Open Drain
PMOS
Analog Lock Detect
8
9
Push-Pull
12 to 15
Mode
0
Normal Operation (default)
1
Entire Device Powered Down
EN_CLKout_Global bit
Clock Outputs
0
All Off
1
Normal Operation (default)
2.9.5 EN_Fout bit -- Fout port enable
This bit enables the Fout pin.
N Divider Output/2
(50% Duty Cycle)
EN_Fout bit
Fout Pin Status
0
Disabled (default)
1
Enabled
2.9.6 PLL_R_DLY [3:0] - Global Skew Adjust, Lag
These bits control the delay stage in front of the R input of the
phase detector. The affect of adjusting this delay is to lag the
phase of the clock outputs uniformly from the clock input
phase by the specified amount.
Invalid
Push-Pull
POWERDOWN bit
2.9.4 EN_CLKout_Global bit -- Global Clock Output
Enable
This bit overrides the individual CLKoutX_EN bits. When this
bit is set to 0, all clock outputs are disabled, regardless of the
state of any of the other bits or pins.
Invalid
10
11
2.9.3 POWERDOWN bit -- Device Power Down
This bit can power down the device. Enabling this bit powers
down the entire device and all blocks, regardless of the state
of any of the other bits or pins.
R Divider Output/2
(50% Duty Cycle)
Invalid
Analog Lock Detect outputs the state of the charge pump on
the LD pin. While the charge pump is on, the LD pin is low.
While the charge pump is off, the LD pin is high. By using two
resistors, a capacitor, diode, and comparator a lock detect
circuit may be constructed (Note 21). When in lock the charge
pump will only turn on momentarily once every period of the
phase detector frequency. "N Divider Output/2" and "R Divider Output/2" output half the frequency of the phase detector on the LD pin. When the device is locked, these
frequencies should be the same. These options are useful for
debugging.
Note 19: If DLD_MODE2 is set, this functionality is redefined to "Frequency
Calibration Routine Complete (Active High)." See 2.4.2 DLD_MODE2 bit -Digital Lock Detect Mode 2 for more information.
PLL_R_DLY[3:0]
Delay (ps)
0
0 (default)
1
150
2
300
3
450
4
600
5
750
6
900
7
1050
8
1200
9
1350
10
1500
Note 20: If DLD_MODE2 is set, this functionality is redefined to "Frequency
Calibration Routine Complete (Active Low)." See 2.4.2 DLD_MODE2 bit -Digital Lock Detect Mode 2 for more information.
11
1650
12
1800
Note 21: For more information on lock detect circuits, see chapter 32 of PLL
Performance, Simulation and Design Handbook, Fourth Edition by Dean
Banerjee.
13
1950
14
2100
15
2250
2.10 REGISTER R15
Programming R15 also activates the frequency calibration
routine while 0_DELAY_MODE = 0. Programming R15 also
causes a global synchronization operation. See sections
2.4.3 0_DELAY_MODE bit -- Activate 0-Delay Mode and 1.6
GLOBAL CLOCK OUTPUT SYNCHRONIZATION respectively for more information.
2.10.1 PLL_N [17:0] -- PLL N Divider
These bits program the divide value for the PLL N Divider.
The PLL N Divider follows the VCO Divider and precedes the
www.national.com
28
PLL_N [17:0]
PLL N
Divider
Value
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Invalid
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
1
. . . . . . . . . . . . . . . . . .
...
0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 0 0 0
760
(default)
. . . . . . . . . . . . . . . . . .
...
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
262143
2.10.3 PLL_CP_GAIN [1:0] -- PLL Charge Pump Gain
These bits set the charge pump gain of the PLL.
PLL_CP_GAIN [1:0]
Charge Pump Gain
0
1x (default)
1
4x
2
16x
3
32x
2.10.2 VCO_DIV [3:0] -- VCO Divider
These bits program the divide value for the VCO Divider. The
VCO Divider follows the VCO output and precedes the clock
distribution blocks. Since the VCO Divider is in the feedback
path from the VCO to the PLL phase detector the VCO Divider
contributes to the total N divide value, NTotal. NTotal = PLL N
Divider × VCO Divider. The VCO Divider can not be bypassed. See the programming section on the PLL N Divider
for more information on setting the VCO frequency.
VCO Divider
Value
VCO_DIV [3:0]
0
0
0
0
0
0
0
1
Invalid
Invalid
0
0
1
0
2 (default)
0
0
1
1
3
0
1
0
0
4
0
1
0
1
5
0
1
1
0
6
0
1
1
1
7
1
0
0
0
8
1
0
0
1
Invalid
.
.
.
.
...
1
1
1
1
Invalid
29
www.national.com
LMK03200 Family
PLL phase detector. Since the VCO Divider is also in the
feedback path from the VCO to the PLL Phase Detector, the
total N divide value, N Total, is also influenced by the VCO Divider value. NTotal = PLL N Divider × VCO Divider. The VCO
frequency is calculated as, fVCO = fOSCin × PLL N Divider ×
VCO Divider / PLL R Divider. Since the PLL N divider is a pure
binary counter there are no illegal divide values for PLL_N
[17:0] except for 0.
LMK03200 Family
2.10.4 PLL_N_DLY [3:0] - Global Skew Adjust, Lead
These bits control the delay stage in front of the N input of the
phase detector. The affect of adjusting this delay is to lead the
phase of the clock outputs uniformly from the clock input
phase by the specified amount.
PLL_N_DLY [3:0]
0
0 (default)
150
2
300
4
5
www.national.com
Delay (ps)
1
3
PLL_N_DLY [3:0]
450
600
750
30
Delay (ps)
6
900
7
1050
8
1200
9
1350
10
1500
11
1650
12
1800
13
1950
14
2100
15
2250
LMK03200 Family
3.0 Application Information
3.1 SYSTEM LEVEL DIAGRAM
30088770
FIGURE 6. Typical Application
Figure 6 shows an LMK03200 family device used in a typical
application. In this setup the clock may be multiplied, reconditioned, and redistributed. Both the OSCin/OSCin* and CLKoutX/CLKoutX* pins can be used in a single-ended or a
differential fashion, which is discussed later in this datasheet.
The GOE pin needs to be high for the outputs to operate. One
technique sometimes used is to take the output of the LD
(Lock Detect) pin and use this as an input to the GOE pin. If
this is done, then the outputs will turn off if lock detect circuit
detects that the PLL is out of lock. The loop filter actually con-
sists of seven components, but four of these components that
for the third and fourth poles of the loop filter are integrated in
the chip. The first and second pole of the loop filter are external.
3.2 BIAS PIN
See section 1.1 BIAS PIN for more information.
3.3 LDO BYPASS
See section 1.2 LDO BYPASS for more information.
31
www.national.com
LMK03200 Family
3.4 LOOP FILTER
30088771
FIGURE 7. Loop Filter
The internal charge pump is directly connected to the integrated loop filter components. The first and second pole of the
loop filter are externally attached as shown in Figure 7. When
the loop filter is designed, it must be stable over the entire
frequency band, meaning that the changes in KVtune from the
low to high band specification will not make the loop filter unstable. The design of the loop filter is application specific and
can be rather involved, but is discussed in depth in the Clock
Conditioner Owner's Manual provided by National Semiconductor. When designing with the integrated loop filter of the
LMK03200 family, considerations for minimum resistor thermal noise often lead one to the decision to design for the
minimum value for integrated resistors, R3 and R4. Both the
www.national.com
integrated loop filter resistors and capacitors (C3 and C4) also
restrict how wide the loop bandwidth the PLL can have. However, these integrated components do have the advantage
that they are closer to the VCO and can therefore filter out
some noise and spurs better than external components. For
this reason, a common strategy is to minimize the internal
loop filter resistors and then design for the largest internal capacitor values that permit a wide enough loop bandwidth. In
some situations where spurs requirements are very stringent
and there is margin on phase noise, it might make sense to
design for a loop filter with integrated resistor values that are
larger than their minimum value.
32
Table 3.5 - Block Current Consumption
Current
Consumption at
3.3 V (mA)
Power
Dissipated in
device (mW)
Power
Dissipated in
LVPECL emitter
resistors (mW)
86.0
283.8
-
Low clock buffer The low clock buffer is enabled anytime one of
(internal)
CLKout0 through CLKout3 are enabled
9
29.7
-
High clock buffer The high clock buffer is enabled anytime one of the
(internal)
CLKout4 through CLKout7 are enabled
9
29.7
-
Fout buffer, EN_Fout = 1
14.5
47.8
-
LVDS output, Bypassed mode
17.8
58.7
-
40
72
60
17.4
38.3
19.1
0
0
-
Block
Condition
Entire device,
core current
All outputs off; No LVPECL emitter resistors connected
Output buffers
LVPECL output, Bypassed mode (includes 120 Ω
emitter resistors)
LVPECL output, disabled mode (includes 120 Ω
emitter resistors)
LVPECL output, disabled mode. No emitter resistors
placed; open outputs
Divide circuitry
per output
Divide enabled, divide = 2
5.3
17.5
-
Divide enabled, divide > 2
8.5
28.0
-
Delay circuitry
per output,
PLL_R_DLY, or
PLL_N_DLY
Delay enabled, delay < 8
5.8
19.1
-
Delay enabled, delay > 7
9.9
32.7
-
Entire device
CLKout0 & CLKout4 enabled in Bypassed mode
161.8
474
60
From Table 3.5 the current consumption can be calculated in
any configuration. For example, the current for the entire device with 1 LVDS (CLKout0) & 1 LVPECL (CLKout4) output
in Bypassed mode can be calculated by adding up the following blocks: core current, low clock buffer, high clock buffer,
one LVDS output buffer current, and one LVPECL output
buffer current. There will also be one LVPECL output drawing
emitter current, but some of the power from the current draw
is dissipated in the external 120 Ω resistors which doesn't add
to the power dissipation budget for the device. If delays or
divides are switched in, then the additional current for these
stages needs to be added as well.
For power dissipated by the device, the total current entering
the device is multiplied by the voltage at the device minus the
power dissipated in any emitter resistors connected to any of
the LVPECL outputs. If no emitter resistors are connected to
the LVPECL outputs, this power will be 0 watts. For example,
in the case of 1 LVDS (CLKout0) & 1 LVPECL (CLKout4) operating at 3.3 volts, we calculate 3.3 V × (86 + 9 + 9 + 17.8 +
40) mA = 3.3 V × 161.8 mA = 533.9 mW. Because the
LVPECL output (CLKout4) has the emitter resistors hooked
up and the power dissipated by these resistors is 60 mW, the
total device power dissipation is 533.9 mW - 60 mW = 473.9
mW.
When the LVPECL output is active, ~1.9 V is the average
voltage on each output as calculated from the LVPECL Voh
& Vol typical specification. Therefore the power dissipated in
each emitter resistor is approximately (1.9 V)2 / 120 Ω = 30
mW. When the LVPECL output is disabled, the emitter resistor voltage is ~1.07 V. Therefore the power dissipated in each
emitter resistor is approximately (1.07 V)2 / 120 Ω = 9.5 mW.
33
www.national.com
LMK03200 Family
calculate estimated current consumption of the device. Unless otherwise noted Vcc = 3.3 V, TA = 25 °C.
3.5 CURRENT CONSUMPTION / POWER DISSIPATION
CALCULATIONS
Due to the myriad of possible configurations the following table serves to provide enough information to allow the user to
LMK03200 Family
3.6 THERMAL MANAGEMENT
Power consumption of the LMK03200 family of devices can
be high enough to require attention to thermal management.
For reliability and performance reasons the die temperature
should be limited to a maximum of 125 °C. That is, as an estimate, TA (ambient temperature) plus device power consumption times θJA should not exceed 125 °C.
The package of the device has an exposed pad that provides
the primary heat removal path as well as excellent electrical
grounding to the printed circuit board. To maximize the removal of heat from the package a thermal land pattern including multiple vias to a ground plane must be incorporated
on the PCB within the footprint of the package. The exposed
pad must be soldered down to ensure adequate heat conduction out of the package. A recommended land and via
pattern can be downloaded from National's packaging website. See LLP footprint gerbers at: http://www.national.com/
analog/packaging/gerber.
To minimize junction temperature it is recommended that a
simple heat sink be built into the PCB (if the ground plane
layer is not exposed). This is done by including a copper area
of about 2 square inches on the opposite side of the PCB from
the device. This copper area may be plated or solder coated
to prevent corrosion but should not have conformal coating (if
possible), which could provide thermal insulation. The vias
should top and bottom copper layers to the ground layer.
These vias act as “heat pipes” to carry the thermal energy
away from the device side of the board to where it can be more
effectively dissipated.
3.7 TERMINATION AND USE OF CLOCK OUTPUTS
(DRIVERS)
When terminating clock drivers keep in mind these guidelines
for optimum phase noise and jitter performance:
• Transmission line theory should be followed for good
impedance matching to prevent reflections.
• Clock drivers should be presented with the proper loads.
For example:
— LVDS drivers are current drivers and require a closed
current loop.
— LVPECL drivers are open emitter and require a DC
path to ground.
• Receivers should be presented with a signal biased to
their specified DC bias level (common mode voltage) for
proper operation. Some receivers have self-biasing inputs
that automatically bias to the proper voltage level. In this
case, the signal should normally be AC coupled.
It is possible to drive a non-LVPECL or non-LVDS receiver
with a LVDS or LVPECL driver as long as the above guidelines are followed. Check the datasheet of the receiver or
input being driven to determine the best termination and coupling method to be sure that the receiver is biased at its
optimum DC voltage (common mode voltage). For example,
when driving the OSCin/OSCin* input of the LMK03200 family, OSCin/OSCin* should be AC coupled because OSCin/
OSCin* biases the signal to the proper DC level, see Figure
6. This is only slightly different from the AC coupled cases
described in 3.7.2 because the DC blocking capacitors are
placed between the termination and the OSCin/OSCin* pins,
but the concept remains the same, which is the receiver (OSCin/OSCin*) set the input to the optimum DC bias voltage
(common mode voltage), not the driver.
3.7.1 Termination for DC Coupled Differential Operation
For DC coupled operation of an LVDS driver, terminate with
100 Ω as close as possible to the LVDS receiver as shown in
Figure 8. The LVDS driver will provide the DC bias level for
the LVDS receiver.
30088720
FIGURE 8. Differential LVDS Operation, DC Coupling
For DC coupled operation of an LVPECL driver, terminate
with 50 Ω to Vcc - 2 V as shown in Figure 9. Alternatively
terminate with a Thevenin equivalent circuit (120 Ω resistor
connected to Vcc and an 82 Ω resistor connected to ground
with the driver connected to the junction of the 120 Ω and 82
Ω resistors) as shown in Figure 10 for Vcc = 3.3 V.
www.national.com
34
30088718
FIGURE 9. Differential LVPECL Operation, DC Coupling
30088719
FIGURE 11. Differential LVDS Operation, AC Coupling
LVPECL drivers require a DC path to ground. When AC coupling an LVPECL signal use 120 Ω emitter resistors close to
the LVPECL driver to provide a DC path to ground as shown
in Figure 12. For proper receiver operation, the signal should
be biased to the DC bias level (common mode voltage) specified by the receiver. The typical DC bias voltage (common
mode voltage) for LVPECL receivers is 2 V. A Thevenin
equivalent circuit (82 Ω resistor connected to Vcc and a 120
Ω resistor connected to ground with the driver connected to
the junction of the 82 Ω and 120 Ω resistors) is a valid termination as shown in Figure 12 for Vcc = 3.3 V. Note this
Thevenin circuit is different from the DC coupled example in
Figure 10.
30088721
FIGURE 10. Differential LVPECL Operation, DC Coupling,
Thevenin Equivalent
30088717
FIGURE 12. Differential LVPECL Operation, AC Coupling,
Thevenin Equivalent
35
www.national.com
LMK03200 Family
3.7.2 Termination for AC Coupled Differential Operation
AC coupling allows for shifting the DC bias level (common
mode voltage) when driving different receiver standards.
Since AC coupling prevents the driver from providing a DC
bias voltage at the receiver it is important to ensure the receiver is biased to its ideal DC level.
When driving LVDS receivers with an LVDS driver, the signal
may be AC coupled by adding DC blocking capacitors, however the proper DC bias point needs to be established at the
receiver. One way to do this is with the termination circuitry in
Figure 11.
LMK03200 Family
When AC coupling an LVPECL driver use a 120 Ω emitter
resistor to provide a DC path to ground and ensure a 50 ohm
termination with the proper DC bias level for the receiver. The
typical DC bias voltage for LVPECL receivers is 2 V (See
3.7.2). If the other driver is not used it should be terminated
with either a proper AC or DC termination. This latter example
of AC coupling a single-ended LVPECL signal can be used to
measure single-ended LVPECL performance using a spectrum analyzer or phase noise analyzer. When using most RF
test equipment no DC bias point (0 V DC) is expected for safe
and proper operation. The internal 50 ohm termination the test
equipment correctly terminates the LVPECL driver being
measured as shown in . When using only one LVPECL driver
of a CLKoutX/CLKoutX* pair, be sure to properly terminated
the unused driver.
3.7.3 Termination for Single-Ended Operation
A balun can be used with either LVDS or LVPECL drivers to
convert the balanced, differential signal into an unbalanced,
single-ended signal.
It is possible to use an LVPECL driver as one or two separate
800 mV p-p signals. When DC coupling one of the LMK03200
family clock LVPECL drivers, the termination should still be
50 ohms to Vcc - 2 V as shown in Figure 13. Again the
Thevenin equivalent circuit (120 Ω resistor connected to Vcc
and an 82 Ω resistor connected to ground with the driver connected to the junction of the 120 Ω and 82 Ω resistors) is a
valid termination as shown in Figure 14 for Vcc = 3.3 V.
30088715
FIGURE 13. Single-Ended LVPECL Operation, DC
Coupling
30088714
FIGURE 15. Single-Ended LVPECL Operation, AC
Coupling
3.7.4 Conversion to LVCMOS Outputs
To drive an LVCMOS input with an LMK03200 family LVDS
or LVPECL output, an LVPECL/LVDS to LVCMOS converter
such
as
National
Semiconductor's
DS90LV018A,
DS90LV028A, DS90LV048A, etc. is required. For best noise
performance, LVPECL provides a higher voltage swing into
input of the converter.
30088716
3.8 OSCin INPUT
In addition to LVDS and LVPECL inputs, OSCin can also be
driven with a sine wave. The OSCin input can be driven single-ended or differentially with sine waves. The configurations
for these are shown in Figure 16 and Figure 17.
FIGURE 14. Single-Ended LVPECL Operation, DC
Coupling, Thevenin Equivalent
30088722
FIGURE 16. Single-Ended Sine Wave Input
www.national.com
36
30088724
FIGURE 17. Differential Sine Wave Input
30088713
FIGURE 18. Recommended OSCin Power for Operation with a Sine Wave Input
an LMK03200 device with eight LMK01000 family devices up
to 64 clocks may be distributed in many different LVDS /
LVPECL combinations. It's possible to distribute more than
64 clocks by adding more LMK01000 family devices. Refer to
AN-1864 for more details.
3.9 MORE THAN EIGHT OUTPUTS WITH AN LMK03200
FAMILY DEVICE
The LMK03200 family devices include eight outputs. When
more than 8 outputs are required the footprint compatible
LMK01000 family may be used for clock distribution. By using
37
www.national.com
LMK03200 Family
Figure 18 shows the recommended power level for sine wave
operation for both differential and single-ended sources over
frequency. The part will operate at power levels below the
recommended power level, but as power decreases the PLL
noise performance will degrade. The VCO noise performance
will remain constant. At the recommended power level the
PLL phase noise degradation from full power operation (8
dBm) is less than 2 dB.
LMK03200 Family
Refer to application note AN-912 Common Data Transmission Parameters and their Definitions for more information.
3.10 DIFFERENTIAL VOLTAGE MEASUREMENT
TERMINOLOGY
The differential voltage of a differential signal can be described by two different definitions causing confusion when
reading datasheets or communicating with other engineers.
This section will address the measurement and description of
a differential signal so that the reader will be able to understand and discern between the two different definitions when
used.
The first definition used to describe a differential signal is the
absolute value of the voltage potential between the inverting
and non-inverting signal. The symbol for this first measurement is typically VID or VOD depending on if an input or output
voltage is being described.
The second definition used to describe a differential signal is
to measure the potential of the non-inverting signal with respect to the inverting signal. The symbol for this second
measurement is VSS and is a calculated parameter. Nowhere
in the IC does this signal exist with respect to ground, it only
exists in reference to its differential pair. VSS can be measured
directly by oscilloscopes with floating references, otherwise
this value can be calculated as twice the value of VOD as described in the first description.
Figure 19 and Figure 20 illustrate the two different definitions
side-by-side for inputs and outputs respectively. The VID and
VOD definitions show VA and VB DC levels that the non-inverting and inverting signals toggle between with respect to
ground. VSS input and output definitions show that if the inverting signal is considered the reference, the non-inverting
signal voltage potential is now increasing and decreasing
above and below the non-inverting reference. Thus the peakto-peak voltage of the differential signal can be measured.
Hence VID and VOD are often defined as volts (V) and VSS is
often defined as volts peak-to-peak (VPP).
www.national.com
30088775
FIGURE 19. Two Different Definitions for Differential
Input Signals
30088774
FIGURE 20. Two Different Definitions for Differential
Output Signals
38
LMK03200 Family
Physical Dimensions inches (millimeters) unless otherwise noted
Leadless Leadframe Package (Bottom View)
48 Pin LLP (SQA48A) Package
Ordering Information
Order Number
VCO Version
Performance Grade
Packing
Package Marking
LMK03200ISQX
1.24 GHz
800 fs
2500 Unit Tape and Reel
K3200 I
LMK03200ISQ
1.24 GHz
800 fs
1000 Unit Tape and Reel
K3200 I
LMK03200ISQE
1.24 GHz
800 fs
250 Unit Tape and Reel
K3200 I
39
www.national.com
LMK03200 Family Precision 0-Delay Clock Conditioner with Integrated VCO
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
Products
Design Support
Amplifiers
www.national.com/amplifiers
WEBENCH® Tools
www.national.com/webench
Audio
www.national.com/audio
App Notes
www.national.com/appnotes
Clock and Timing
www.national.com/timing
Reference Designs
www.national.com/refdesigns
Data Converters
www.national.com/adc
Samples
www.national.com/samples
Interface
www.national.com/interface
Eval Boards
www.national.com/evalboards
LVDS
www.national.com/lvds
Packaging
www.national.com/packaging
Power Management
www.national.com/power
Green Compliance
www.national.com/quality/green
Switching Regulators
www.national.com/switchers
Distributors
www.national.com/contacts
LDOs
www.national.com/ldo
Quality and Reliability
www.national.com/quality
LED Lighting
www.national.com/led
Feedback/Support
www.national.com/feedback
Voltage Reference
www.national.com/vref
Design Made Easy
www.national.com/easy
www.national.com/powerwise
Solutions
www.national.com/solutions
Mil/Aero
www.national.com/milaero
PowerWise® Solutions
Serial Digital Interface (SDI) www.national.com/sdi
Temperature Sensors
www.national.com/tempsensors SolarMagic™
www.national.com/solarmagic
Wireless (PLL/VCO)
www.national.com/wireless
www.national.com/training
PowerWise® Design
University
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2009 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Technical Support Center
Email: [email protected]
National Semiconductor Asia
Pacific Technical Support Center
Email: [email protected]
National Semiconductor Japan
Technical Support Center
Email: [email protected]