MICROCIRCUIT DATA SHEET Original Creation Date: 07/16/96 Last Update Date: 05/25/99 Last Major Revision Date: 03/12/99 MN54ACTQ574-X REV 2A0 Octal D Flip-Flop with TRI-STATE Outputs General Description The ACTQ574 is a high-speed, low-power octal D-type flip-flop with a buffered Common Clock (CP) and a buffered common Output Enable(OE). The information presented to the D inputs is stored in the flip-flops on the LOW-to-HIGH clock (CP) transition. The ACTQ574 utilizes Quiet Series technology to guarantee quiet output switching and improve dynamic threshold performance. FACT Quiet Series TM features G TO TM output control and undershoot corrector in addition to a split ground bus for superior performance. The ACTQ574 is functionally identical to the ACTQ374 but with different pin-out. Industry Part Number NS Part Numbers 54ACTQ574 54ACTQ574DMQB 54ACTQ574FMQB 54ACTQ574LMQB Prime Die D574 Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 Quality Conformance Inspection MIL-STD-883 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 C +125 C -55 C +25 C +125 C -55 C +25 C +125 C -55 C +25 C +125 C -55 C MICROCIRCUIT DATA SHEET MN54ACTQ574-X REV 2A0 Features - Icc and Ioz reduced by 50% Guaranteed simultaneous switching noise level and dynamic threshold performance Guaranteed pin-to-pin skew AC performance Inputs and outputs on opposite sides of the package allowing easy interface with microprocessors. Functionally identical to the ACQ/ACTQ374 TRI-STATE outputs drive bus lines or buffer memory address registers Outputs source/sink 24 mA 4 kV minimum ESD immunity 2 MICROCIRCUIT DATA SHEET MN54ACTQ574-X REV 2A0 (Absolute Maximum Ratings) (Note 1) Supply Voltage (Vcc) -0.5V to +7.0V DC Input Vi = Vi = DC Input Diode Current (Iik) -0.5V Vcc +0.5V Voltage (Vi) -20 mA +20 mA -0.5V to Vcc +0.5V DC Output Diode Current (Iok) Vo = -0.5V Vo = Vcc +0.5V DC Output Voltage (Vo) -20 mA +20 mA -0.5 to Vcc +0.5V DC Output Source or Sink Current (Io) +50 mA DC Vcc or Ground Current per Output Pin (Icc or Ignd) +50 mA Storage Temperature (Tstg) -65 C to + 150 C DC Latch-Up Source or Sink Current +300 mA Junction Temperature (Tj) CDIP Note 1: 175 C Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. National does not recommend operation of FACT TM circuits outside databook specifications. Recommended Operating Conditions (Note 1) Supply Voltage (Vcc) 4.5V to 5.5V Input Voltage (Vi) 0V to Vcc Output Voltage (Vo) 0V to Vcc Operating Temperature (Ta) -55 C to + 125 C Minimum Input Edge Rate (Delta V/Delta t) ACTQ Devices Vin from 0.8V to 2.0V Vcc @ 4.5V, 5.5V Note 1: 125 mV/ns All commercial packaging is not recommended for applications requiring greater than 2000 temperature cycles from -40C to +125C. 3 MICROCIRCUIT DATA SHEET MN54ACTQ574-X REV 2A0 Electrical Characteristics DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: VCC 4.5V to 5.5V, Temp. Range: -55C to 125C. NOTE: -55C TEMPERATURE, SUBGROUP 3 IS GUARANTEED BUT NOT TESTED. SYMBOL IIH IIL VOL PARAMETER High Level input Current Low Level input Current Low level output voltage CONDITIONS NOTES VCC=5.5V, VM=5.5V PINNAME MIN MAX UNIT SUBGROUPS 1, 2 INPUT 0.1 uA 1 1, 2 INPUT 1.0 uA 2, 3 1, 2 INPUT -0.1 uA 1 1, 2 INPUT -1.0 uA 2, 3 1, 2 OUTPUT .36 V 1 1, 2 OUTPUT .50 V 2, 3 VCC=4.5V, VIL=0.8V, IOL=50.0uA, VIH=2.0V 1, 2 OUTPUT .10 V 1, 2, 3 VCC=5.5V, VIL=0.8V, IOL=24.0mA, VIH=2.0V 1, 2 OUTPUT .36 V 1 1, 2 OUTPUT .50 V 2, 3 VCC=5.5V, VIL=0.8V, IOL=50.0uA, VIH=2.0V 1, 2 OUTPUT .10 V 1, 2, 3 1.65 V 1, 2, 3 VCC=5.5V, VM=0.0V VCC=4.5V, VIL=0.8V, IOL=24.0mA, VIH=2.0V VIOL Dynamic Output current LOW VCC=5.5V, VIH=5.5V, VIL=0.0V, IOL=50.0mA 1, OUTPUT 2, 5 VOH High Level Output Voltage VCC=4.5V, VIL=0.8V, IOH=-24.0mA, VIH=2.0V 1, 2 OUTPUT 3.86 V 1 1, 2 OUTPUT 3.70 V 2, 3 VCC=4.5V, VIL=0.8V, IOH=-50.0uA, VIH=2.0V 1, 2 OUTPUT 4.40 V 1, 2, 3 VCC=5.5V, VIL=0.8V, IOH=-24.0mA, VIH=2.0V 1, 2 OUTPUT 4.86 V 1 1, 2 OUTPUT 4.70 V 2, 3 VCC=5.5V, VIL=0.8V, IOH=-50.0uA, VIH=2.0V 1, 2 OUTPUT 5.40 V 1, 2, 3 3.85 V 1, 2, 3 VIOH Dynamic Output current HIGH VCC=5.5V, VIH=5.5V, VIL=0.0V, IOH=-50.0mA 1, OUTPUT 2, 5 ICCH Supply Current VCC=5.5V 1, 2 VCC 4.0 uA 1 1, 2 VCC 80 uA 2, 3 1, 2 VCC 4.0 uA 1 1, 2 VCC 80 uA 2, 3 1, 2 VCC 4.0 uA 1 1, 2 VCC 80 uA 2, 3 1, 2 VCC 1.0 mA 1 1, 2 VCC 1.6 mA 2, 3 ICCZ ICCL ICCT Supply Current Supply Current Supply Current VCC=5.5V VCC=5.5V VCC=5.5V, VIHT=VCC-2.1V 4 MICROCIRCUIT DATA SHEET MN54ACTQ574-X REV 2A0 Electrical Characteristics DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: VCC 4.5V to 5.5V, Temp. Range: -55C to 125C. NOTE: -55C TEMPERATURE, SUBGROUP 3 IS GUARANTEED BUT NOT TESTED. SYMBOL IOZH PARAMETER Maximum TRI-STATE Leakage current CONDITIONS NOTES VCC=4.5V, VM=4.5V, VIH=2.0V VCC=5.5V, VM=5.5V, VIH=2.0V IOZL Maximum TRI-STATE Leakage current VCC=4.5V, VM=0.0V, VIH=2.0V VCC=5.5V, VM=0.0V, VIH=2.0V PINNAME MIN MAX UNIT SUBGROUPS 1, 2 OUTPUT 0.25 uA 1 1, 2 OUTPUT 5.0 uA 2, 3 1, 2 OUTPUT 0.25 uA 1 1, 2 OUTPUT 5.0 uA 2, 3 1, 2 OUTPUT -0.25 uA 1 1, 2 OUTPUT -5.0 uA 2, 3 1, 2 OUTPUT -0.25 uA 1 1, 2 OUTPUT -5.0 uA 2, 3 VIKL VCC=4.5V, IKL=-18mA 1, 2 INPUT -1.2 V 1, 2, 3 VIKH VCC=4.5V, IKH=18mA 1, 2 INPUT 5.7 V 1, 2, 3 0.8 V 4 V 4 VILD Maximum Low Level Dynamic Input Voltage VCC=5.0V, LOAD 50pF / 500 OHMS 6, 9 INPUT VIHD Minimum High Level Dynamic Input Voltage VCC=5.0V, LOAD 50pF / 500 OHMS 6, 9 INPUT VOLP Quiet Output Maximum Dynamic Vol VCC=5.0V, LOAD 50pF / 500 OHMS 6, 8 OUTPUT 1.5 V 4 VOLV Quiet Output Minimum Dynamic Vol VCC=5.0V, LOAD 50pF / 500 OHMS 6, 8 OUTPUT -1.2 V 4 5 2.2 MICROCIRCUIT DATA SHEET MN54ACTQ574-X REV 2A0 Electrical Characteristics AC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) AC: CL=50pf, RL=500 OHMS, TR/TF=3.0ns, Temp range: -55C to +125C. NOTE: -55C TEMPERATURE, SUBGROUP 11 IS GUARANTEED BUT NOT TESTED. SYMBOL tpLH tpHL tpZH tpZL tpHZ tpLZ PARAMETER Propagation Delay Propagation Delay Output Enable Time Output Enable Time Output Disable Time Output Disable Time CONDITIONS NOTES VCC=4.5V VCC=4.5V VCC=4.5V VCC=4.5V VCC=4.5V VCC=4.5V PINNAME MIN MAX UNIT SUBGROUPS 3, CP to 4, 7 On 1.5 9.5 ns 9 3, CP to 4, 7 On 1.5 11.0 ns 10, 11 3, CP to 4, 7 On 1.5 9.5 ns 9 3, CP to 4, 7 On 1.5 11.0 ns 10, 11 3, OE to 4, 7 On 1.5 9.5 ns 9 3, OE to 4, 7 On 1.5 11.0 ns 10, 11 3, OE to 4, 7 On 1.5 9.5 ns 9 3, OE to 4, 7 On 1.5 11.0 ns 10, 11 3, OE to 4, 7 On 1.5 8.5 ns 9 3, OE to 4, 7 On 1.5 10.0 ns 10, 11 3, OE to 4, 7 On 1.5 8.5 ns 9 3, OE to 4, 7 On 1.5 10.0 ns 10, 11 ts(H/L) Setup Time HIGH or LOW VCC=4.5V 6 Dn to CP 3.5 ns 9, 10, 11 th(H/L) Hold Time HIGH or LOW VCC=4.5V 6 Dn to CP 2.0 ns 9, 10, 11 tw(H/L) Pulse Width VCC=4.5V 6 CP 5.0 ns 9, 10, 11 fMAX Maximum Clock Frequency VCC=4.5V 6 CP 95 MHz 9, 10, 11 Note 1: Note 5: SCREEN TESTED 100% ON EACH DEVICE AT +25C & +125C TEMPERATURE, SUBGROUPS 1, 2, 7, & 8. SAMPLE TESTED (METHOD 5005, TABLE 1) ON EACH MFG. LOT AT +25C & +125C TEMPERATURE, SUBGROUPS A1, 2, 7, & 8. SCREEN TESTED 100% ON EACH DEVICE AT +25C TEMPERATURE ONLY SUBGROUP A9. SAMPLE TESTED (METHOD 5005, TABLE 1) ON EACH MFG. LOT AT +25C & +125C TEMPERATURE, SUBGROUPS A9 & 10. TRANSMISSION LINE DRIVING TEST, GUARDBANDED LIMITS SET FOR +25C, 2 MSEC DURATION MAX. Note 6: Note 7: GUARANTEED BUT NOT TESTED. (DESIGN CHARACTERIZATION DATA) +25C & +125C MIN LIMITS GUARANTEED FOR 5.5V BY GUARDBANDING 4.5V MIN. LIMITS. Note 2: Note 3: Note 4: 6 MICROCIRCUIT DATA SHEET MN54ACTQ574-X REV 2A0 (Continued) Note 8: Note 9: MAX NUMBER OF OUTPUTS DEFINED AS (N). DATA INPUTS ARE DRIVEN 0V TO 3V. ONE OUTPUT @ VOL. MAX NUMBER OF DATA INPUTS (N) SWITCHING. (N-1) INPUTS SWITCHING 0V TO 3V. INPUT-UNDER-TEST SWITCHING 3V TO THRESHOLD (VILD), 0V TO THRESHOLD (VIHD), FREQ= 1 MHZ. 7 MICROCIRCUIT DATA SHEET MN54ACTQ574-X REV 2A0 Revision History Rev ECN # 2A0 M0003315 05/25/99 Rel Date Originator Changes Linda Collins Removed the reference to SMD 5962-8960102 from the Features section. Changed the test condition from VIHT=VCC-2.0V to VIHT=VCC-2.1V for ICCT. Changed the test conditions from VM=4.5V to VM=0.0V and VM=5.5V to VM=0.0V for IOZL. 8