ETC TPS2024DR

TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
D
D
D
D
D
D
D
D
D
D
D
D
33-mΩ (5-V Input) High-Side MOSFET
Switch
Short-Circuit and Thermal Protection
Overcurrent Logic Output
Operating Range . . . 2.7 V to 5.5 V
Logic-Level Enable Input
Typical Rise Time . . . 6.1 ms
Undervoltage Lockout
Maximum Standby Supply
Current . . . 10 µA
No Drain-Source Back-Gate Diode
Available in 8-pin SOIC and PDIP Packages
Ambient Temperature Range, – 40°C to 85°C
2-kV Human-Body-Model, 200-V
Machine-Model ESD Protection
D OR P PACKAGE
(TOP VIEW)
GND
IN
IN
EN
1
8
2
7
3
6
4
5
OUT
OUT
OUT
OC
description
The TPS202x family of power distribution switches is intended for applications where heavy capacitive loads
and short circuits are likely to be encountered. These devices are 50-mΩ N-channel MOSFET high-side power
switches. The switch is controlled by a logic enable compatible with 5-V logic and 3-V logic. Gate drive is
provided by an internal charge pump designed to control the power-switch rise times and fall times to minimize
current surges during switching. The charge pump requires no external components and allows operation from
supplies as low as 2.7 V.
When the output load exceeds the current-limit threshold or a short is present, the TPS202x limits the output
current to a safe level by switching into a constant-current mode, pulling the overcurrent (OC) logic output low.
When continuous heavy overloads and short circuits increase the power dissipation in the switch, causing the
junction temperature to rise, a thermal protection circuit shuts off the switch to prevent damage. Recovery from
a thermal shutdown is automatic once the device has cooled sufficiently. Internal circuitry ensures the switch
remains off until valid input voltage is present.
The TPS202x devices differ only in short-circuit current threshold. The TPS2020 limits at 0.3-A load, the
TPS2021 at 0.9-A load, the TPS2022 at 1.5-A load, the TPS2023 at 2.2-A load, and the TPS2024 at 3-A load
(see Available Options). The TPS202x is available in an 8-pin small-outline integrated-circuit (SOIC) package
and in an 8-pin dual-in-line (DIP) package and operates over a junction temperature range of – 40°C to 125°C.
GENERAL SWITCH CATALOG
33 mΩ, single TPS201xA 0.2 A – 2 A
TPS202x
TPS203x
80 mΩ, single TPS2014
TPS2015
TPS2041
TPS2051
TPS2045
TPS2055
80 mΩ, dual
0.2 A – 2 A
0.2 A – 2 A
600 mA
1A
500 mA
500 mA
250 mA
250 mA
260 mΩ
IN1
OUT
IN2
1.3 Ω
TPS2042
TPS2052
TPS2046
TPS2056
500 mA
500 mA
250 mA
250 mA
TPS2100/1
IN1 500 mA
IN2 10 mA
TPS2102/3/4/5
IN1
500 mA
IN2
100 mA
80 mΩ, triple
TPS2043
TPS2053
TPS2047
TPS2057
500 mA
500 mA
250 mA
250 mA
80 mΩ, quad
TPS2044
TPS2054
TPS2048
TPS2058
500 mA
500 mA
250 mA
250 mA
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
1
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
AVAILABLE OPTIONS
RECOMMENDED
MAXIMUM CONTINUOUS
LOAD CURRENT
(A)
TYPICAL SHORT-CIRCUIT
CURRENT LIMIT AT 25°C
(A)
SMALL OUTLINE
(D)†
PLASTIC DIP
(P)
0.2
0.3
TPS2020D
TPS2020P
0.6
0.9
TPS2021D
TPS2021P
1
1.5
TPS2022D
TPS2022P
1.5
2.2
TPS2023D
TPS2023P
2
3
TPS2024D
† The D package is available taped and reeled. Add an R suffix to device type (e.g., TPS2020DR)
TPS2024P
TA
– 40°C to 85°C
ENABLE
Active low
PACKAGED DEVICES
TPS2020 functional block diagram
Power Switch
†
CS
IN
OUT
Charge
Pump
EN
Current
Limit
Driver
OC
UVLO
Thermal
Sense
GND
†Current Sense
Terminal Functions
TERMINAL
NO.
D OR P
I/O
EN
4
I
Enable input. Logic low turns on power switch.
GND
1
I
Ground
NAME
DESCRIPTION
IN
2, 3
I
Input voltage
OC
5
O
Overcurrent. Logic output active low
6, 7, 8
O
Power-switch output
OUT
2
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
detailed description
power switch
The power switch is an N-channel MOSFET with a maximum on-state resistance of 50 mΩ (VI(IN) = 5 V).
Configured as a high-side switch, the power switch prevents current flow from OUT to IN and IN to OUT when
disabled.
charge pump
An internal charge pump supplies power to the driver circuit and provides the necessary voltage to pull the gate
of the MOSFET above the source. The charge pump operates from input voltages as low as 2.7 V and requires
very little supply current.
driver
The driver controls the gate voltage of the power switch. To limit large current surges and reduce the associated
electromagnetic interference (EMI) produced, the driver incorporates circuitry that controls the rise times and
fall times of the output voltage. The rise and fall times are typically in the 2-ms to 9-ms range.
enable ( EN)
The logic enable disables the power switch, the bias for the charge pump, driver, and other circuitry to reduce
the supply current to less than 10 µA when a logic high is present on EN . A logic zero input on EN restores bias
to the drive and control circuits and turns the power on. The enable input is compatible with both TTL and CMOS
logic levels.
overcurrent ( OC)
The OC open drain output is asserted (active low) when an overcurrent or overtemperature condition is
encountered. The output will remain asserted until the overcurrent or overtemperature condition is removed.
current sense
A sense FET monitors the current supplied to the load. The sense FET measures current more efficiently than
conventional resistance methods. When an overload or short circuit is encountered, the current-sense circuitry
sends a control signal to the driver. The driver, in turn, reduces the gate voltage and drives the power FET into
its saturation region, which switches the output into a constant current mode and holds the current constant
while varying the voltage on the load.
thermal sense
An internal thermal-sense circuit shuts off the power switch when the junction temperature rises to
approximately 140°C. Hysteresis is built into the thermal sense circuit. After the device has cooled
approximately 20°C, the switch turns back on. The switch continues to cycle off and on until the fault is removed.
undervoltage lockout
A voltage sense circuit monitors the input voltage. When the input voltage is below approximately 2 V, a control
signal turns off the power switch.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
3
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Input voltage range, VI(IN) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 6 V
Output voltage range, VO(OUT) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to VI(IN) + 0.3 V
Input voltage range, VI(EN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to 6 V
Continuous output current, IO(OUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . internally limited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating virtual junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 125°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . 260°C
Electrostatic discharge (ESD) protection: Human body model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
Machine model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200V
Charged device model (CDM) . . . . . . . . . . . . . . . . . . . . . . . . . 750 V
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltages are with respect to GND.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
D
725 mW
5.8 mW/°C
464 mW
377 mW
P
1175 mW
9.4 mW/°C
752 mW
611 mW
recommended operating conditions
Input voltage
Continuous output current, IO
MIN
MAX
2.7
5.5
V
0
5.5
V
TPS2020
0
0.2
TPS2021
0
0.6
TPS2022
0
1
TPS2023
0
1.5
TPS2024
0
2
– 40
125
VI(IN)
VI(EN)
Operating virtual junction temperature, TJ
4
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
UNIT
A
°C
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
electrical characteristics over recommended operating junction temperature range, VI(IN)= 5.5 V,
IO = rated current, EN = 0 V (unless otherwise noted)
power switch
TEST CONDITIONS†
PARAMETER
rDS(on)
tr
tf
Static drain-source on-state resistance
Rise time
time, output
Fall time,
time output
MIN
TYP
MAX
VI(IN) = 5 V,
TJ = 25°C,
IO = 1.8 A
33
36
VI(IN) = 5 V,
TJ = 85°C,
IO = 1.8 A
38
46
VI(IN) = 5 V,
TJ = 125°C,
IO = 1.8 A
44
50
VI(IN) = 3.3 V,
TJ = 25°C,
IO = 1.8 A
37
41
VI(IN) = 3.3 V,
TJ = 85°C,
IO = 1.8 A
43
52
VI(IN) = 3.3 V,
TJ = 125°C,
IO = 1.8 A
51
61
VI(IN) = 5 V,
TJ = 25°C,
IO = 0.18 A
30
34
VI(IN) = 5 V,
TJ = 85°C,
IO = 0.18 A
35
41
VI(IN) = 5 V,
TJ = 125°C,
IO = 0.18 A
39
47
VI(IN) = 3.3 V,
TJ = 25°C,
IO = 0.18 A
33
37
VI(IN) = 3.3 V,
TJ = 85°C,
IO = 0.18 A
39
46
VI(IN) = 3.3 V,
TJ = 125°C,
IO = 0.18 A
44
56
VI(IN) = 5.5 V,
CL = 1 µF,
TJ = 25°C,
RL = 10 Ω
6.1
VI(IN) = 2.7 V,
CL = 1 µF,
TJ = 25°C,
RL = 10 Ω
8.6
VI(IN) = 5.5 V,
CL = 1 µF,
VI(IN) = 2.7 V,
CL = 1 µF,
TJ = 25°C,
RL = 10 Ω
TJ = 25°C,
RL = 10 Ω
UNIT
mΩ
ms
3.4
ms
3
† Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account separately.
enable input ( EN)
PARAMETER
VIH
High-level input voltage
VIL
Low-level in
input
ut voltage
TEST CONDITIONS
2.7 V ≤ VI(IN) ≤ 5.5 V
TYP
MAX
2
0.8
2.7 V ≤ VI(IN) ≤ 4.5 V
0.5
Input current
EN= 0 V or EN = VI(IN)
ton
toff
Turnon time
CL = 100 µF, RL = 10 Ω
CL = 100 µF, RL = 10 Ω
UNIT
V
4.5 V ≤ VI(IN) ≤ 5.5 V
II
Turnoff time
MIN
– 0.5
0.5
20
40
V
µA
ms
current limit
TEST CONDITIONS†
PARAMETER
IOS
Short-circuit output current
TJ = 25
25°C,
C, VI = 5.5 V,
OUT connected to GND,
Device enable into short circuit
MIN
TYP
MAX
TPS2020
0.22
0.3
0.4
TPS2021
0.66
0.9
1.1
TPS2022
1.1
1.5
1.8
TPS2023
1.65
2.2
2.7
TPS2024
2.2
3
UNIT
A
3.8
† Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account separately.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
5
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
electrical characteristics over recommended operating junction temperature range, VI(IN)= 5.5 V,
IO = rated current, EN = 0 V (unless otherwise noted) (continued)
supply current
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
Supply current
current, low
low-level
level output
No Load on OUT
TJ = 25°C
– 40°C ≤ TJ ≤ 125°C
0.3
EN = VI(IN)
1
current high-level
high level output
Supply current,
No Load on OUT
TJ = 25°C
– 40°C ≤ TJ ≤ 125°C
58
75
EN = 0 V
75
100
Leakage current
OUT connected to ground
EN = VI(IN)
– 40°C ≤ TJ ≤ 125°C
10
10
UNIT
µA
µA
µA
undervoltage lockout
PARAMETER
TEST CONDITIONS
Low-level input voltage
MIN
TYP
2
Hysteresis
TJ = 25°C
MAX
2.5
100
UNIT
V
mV
overcurrent (OC)
PARAMETER
Output low voltage
Off-state current†
TEST CONDITIONS
IO = 10 mA,
VOL(OC)
VO = 5 V, VO = 3.3 V
† Specified by design, not production tested.
6
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
MIN
TYP
MAX
UNIT
0.4
V
1
µA
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
PARAMETER MEASUREMENT INFORMATION
OUT
RL
tf
tr
CL
VO(OUT)
90%
10%
90%
10%
TEST CIRCUIT
50%
VI(EN)
50%
toff
ton
90%
VO(OUT)
10%
VOLTAGE WAVEFORMS
Figure 1. Test Circuit and Voltage Waveforms
Table of Timing Diagrams
FIGURE
Turnon Delay and Rise TIme
2
Turnoff Delay and Fall Time
3
Turnon Delay and Rise TIme with 1-µF Load
4
Turnoff Delay and Rise TIme with 1-µF Load
5
Device Enabled into Short
6
TPS2020, TPS2021, TPS2022, TPS2023, and TPS2024, Ramped Load on Enabled Device
7, 8, 9,
10, 11
TPS2024, Inrush Current
12
7.9-Ω Load Connected to an Enabled TPS2020 Device
13
3.7-Ω Load Connected to an Enabled TPS2020 Device
14
3.7-Ω Load Connected to an Enabled TPS2021 Device
15
2.6-Ω Load Connected to an Enabled TPS2021 Device
16
2.6-Ω Load Connected to an Enabled TPS2022 Device
17
1.2-Ω Load Connected to an Enabled TPS2022 Device
18
1.2-Ω Load Connected to an Enabled TPS2023 Device
19
0.9-Ω Load Connected to an Enabled TPS2023 Device
20
0.9-Ω Load Connected to an Enabled TPS2024 Device
21
0.5-Ω Load Connected to an Enabled TPS2024 Device
22
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
7
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
PARAMETER MEASUREMENT INFORMATION
VI(EN) (5 V/div)
VI(EN) (5 V/div)
VI(EN)
VI(EN)
VI(IN) = 5 V
RL = 27 Ω
TA = 25°C
VO(OUT) (2 V/div)
VO(OUT) (2 V/div)
VIN = 5 V
RL = 27 Ω
TA = 25°C
VO(OUT)
0
2
4
6
8
10
12
14
16
18
VO(OUT)
20
2
0
4
6
8
10
12
14
16
18
20
t – Time – ms
t – Time – ms
Figure 2. Turnon Delay and Rise Time
Figure 3. Turnoff Delay and Fall Time
VI(EN) (5 V/div)
VI(EN) (5 V/div)
VI(EN)
VI(EN)
VO(OUT) (2 V/div)
VO(OUT) (2 V/div)
VI(IN) = 5 V
CL = 1 µF
RL = 27 Ω
TA = 25°C
VO(OUT)
0
2
4
6
8
10
12
14
16
18
VI(IN) = 5 V
CL = 1 µF
RL = 27 Ω
TA = 25°C
VO(OUT)
20
0
2
8
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
6
8
10
12
14
16
18
t – Time – ms
t – Time – ms
Figure 4. Turnon Delay and Rise Time
With 1-µF Load
4
Figure 5. Turnoff Delay and Fall Time
With 1-µF Load
• DALLAS, TEXAS 75265
20
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
PARAMETER MEASUREMENT INFORMATION
VO(OC) (5 V/div)
VI(EN)
VI(EN) (5 V/div)
VO(OC)
VI(IN) = 5 V
TA = 25°C
VI(IN) = 5 V
TA = 25°C
TPS2024
TPS2023
IO(OUT) (500 mA/div)
TPS2022
TPS2021
TPS2020
IO(OUT)
IO(OUT)
IO(OUT) (1 A/div)
0
1
2
3
4
5
6
7
8
9
0
10
20
40
60
80 100 120 140 160 180 200
t – Time – ms
t – Time – ms
Figure 7. TPS2020, Ramped Load on
Enabled Device
Figure 6. Device Enabled Into Short
VO(OC) (5 V/div)
VO(OC)
VO(OC) (5 V/div)
VO(OC)
VI(IN) = 5 V
TA = 25°C
VI(IN) = 5 V
TA = 25°C
IO(OUT) (1 A/div)
IO(OUT) (1 A/div)
IO(OUT)
IO(OUT)
0
20
40
60
80 100 120 140 160 180 200
0
20
t – Time – ms
60
80 100 120 140 160 180 200
t – Time – ms
Figure 8. TPS2021, Ramped Load on Enabled
Device
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
40
Figure 9. TPS2022, Ramped Load on
Enabled Device
• DALLAS, TEXAS 75265
9
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
PARAMETER MEASUREMENT INFORMATION
VO(OC) (5 V/div)
VO(OC) (5 V/div)
VO(OC)
VO(OC)
VI(IN) = 5 V
TA = 25°C
VI(IN) = 5 V
TA = 25°C
IO(OUT) (1 A/div)
IO(OUT) (1 A/div)
IO(OUT)
IO(OUT)
0
20
40
60
80 100 120 140 160 180 200
0
20
t – Time – ms
40
60
80 100 120 140 160 180 200
t – Time – ms
Figure 11. TPS2024, Ramped Load on Enabled
Device
Figure 10. TPS2023, Ramped Load on
Enabled Device
VI(EN)
VO(OC) (5 V/div)
VI(EN) (5 V/div)
VO(OC)
IO(OUT) (200 mA/div)
470 µF
150 µF
II(IN) (500 mA/div)
II(IN)
RL = 10 Ω
TA = 25°C
47 µF
0
1
2
3
4
5
6
7
8
9
VI(IN) = 5 V
RL = 7.9 Ω
TA = 25°C
IO(OUT)
10
0
200 400 600 800 1000 1200 1400 1600 1800 2000
t – Time – µs
t – Time – ms
Figure 12. TPS2024, Inrush Current
10
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
Figure 13. 7.9-Ω Load Connected to an Enabled
TPS2020 Device
• DALLAS, TEXAS 75265
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
PARAMETER MEASUREMENT INFORMATION
VO(OC) (5 V/div)
VO(OC) (5 V/div)
VO(OC)
VO(OC)
VI(IN) = 5 V
RL = 3.7 Ω
TA = 25°C
VI(IN) = 5 V
RL = 3.7 Ω
TA = 25°C
IO(OUT) (500 mA/div)
IO(OUT) (1 A/div)
IO(OUT)
IO(OUT)
0
50 100 150 200 250 300 350 400 450 500
0
200 400 600 800 1000 1200 1400 1600 1800 2000
t – Time – µs
t – Time – µs
Figure 14. 3.7-Ω Load Connected to an Enabled
TPS2020 Device
Figure 15. 3.7-Ω Load Connected to an Enabled
TPS2021 Device
VO(OC)
VO(OC) (5 V/div)
VO(OC) (5 V/div)
VO(OC)
VI(IN) = 5 V
RL = 2.6 Ω
TA = 25°C
VI(IN) = 5 V
RL = 2.6 Ω
TA = 25°C
IO(OUT) (1 A/div)
IO(OUT) (1 A/div)
IO(OUT)
IO(OUT)
0
50 100 150 200 250 300 350 400 450 500
0
200 400 600 800 1000 1200 1400 1600 1800 2000
t – Time – µs
t – Time – µs
Figure 16. 2.6-Ω Load Connected to an Enabled
TPS2021 Device
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
Figure 17. 2.6-Ω Load Connected to an Enabled
TPS2022 Device
• DALLAS, TEXAS 75265
11
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
PARAMETER MEASUREMENT INFORMATION
VO(OC) (5 V/div)
VO(OC) (5 V/div)
VO(OC)
VO(OC)
VI(IN) = 5 V
RL = 1.2 Ω
TA = 25°C
IO(OUT) (1 A/div)
IO(OUT) (2 A/div)
IO(OUT)
VI(IN) = 5 V
RL = 1.2 Ω
TA = 25°C
IO(OUT)
0
100 200 300 400 500 600 700 800 900 1000
0
100 200 300 400 500 600 700 800 900 1000
t – Time – µs
t – Time – µs
Figure 18. 1.2-Ω Load Connected to an Enabled
TPS2022 Device
Figure 19. 1.2-Ω Load Connected to an Enabled
TPS2023 Device
VO(OC) (5 V/div)
VO(OC) (5 V/div)
VO(OC)
VO(OC)
VI(IN) = 5 V
RL = 0.9 Ω
TA = 25°C
VI(IN) = 5 V
RL = 0.9 Ω
TA = 25°C
IO(OUT) (2 A/div)
IO(OUT) (5 A/div)
IO(OUT)
IO(OUT)
0
100 200 300 400 500 600 700 800 900 1000
0
100 200 300 400 500 600 700 800 900 1000
t – Time – µs
t – Time – µs
Figure 20. 0.9-Ω Load Connected to an Enabled
TPS2023 Device
12
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
Figure 21. 0.9-Ω Load Connected to an Enabled
TPS2024 Device
• DALLAS, TEXAS 75265
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
PARAMETER MEASUREMENT INFORMATION
VO(OC) (5 V/div)
VO(OC)
VI(IN) = 5 V
RL = 0.5 Ω
TA = 25°C
IO(OUT) (5 A/div)
IO(OUT)
0
50 100 150 200 250 300 350 400 450 500
t – Time – µs
Figure 22. 0.5-Ω Load Connected to an Enabled
TPS2024 Device
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
td(on)
td(off)
Turnon delay time
vs Output voltage
23
Turnoff delay time
vs Input voltage
24
tr
tf
Rise time
vs Load current
25
Fall time
vs Load current
26
Supply current (enabled)
vs Junction temperature
27
Supply current (disabled)
vs Junction temperature
28
Supply current (enabled)
vs Input voltage
29
Supply current (disabled)
vs Input voltage
30
vs Input voltage
31
vs Junction temperature
32
vs Input voltage
33
vs Junction temperature
34
vs Input voltage
35
vs Junction temperature
36
Undervoltage lockout
37
IOS
Short circuit current limit
Short-circuit
rDS(
DS(on))
Static drain-source
drain source on-state
on state resistance
VI
Input voltage
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
13
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
TYPICAL CHARACTERISTICS
TURNON DELAY TIME
vs
OUTPUT VOLTAGE
TURNOFF DELAY TIME
vs
INPUT VOLTAGE
18
TA = 25°C
CL = 1 µF
7
t d(off) – Turn-off Delay Time – ms
t d(on) – Turn-on Delay Time – ms
7.5
6.5
6
5.5
5
4.5
TA = 25°C
CL = 1 µF
17.5
17
16.5
4
3.5
2.5
3
5
3.5
4
4.5
VI – Input Voltage – V
5.5
16
2.5
6
3
3.5
4
4.5
5
VI – Input Voltage – V
Figure 23
Figure 24
RISE TIME
vs
LOAD CURRENT
FALL TIME
vs
LOAD CURRENT
6.5
5.5
6
3.5
TA = 25°C
CL = 1 µF
TA = 25°C
CL = 1 µF
t f – Fall Time – ms
t r – Rise Time – ms
3.25
6
5.5
3
2.75
5
0
0.5
1
1.5
IL – Load Current – A
2
2.5
0
Figure 25
14
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
0.5
1
1.5
IL – Load Current – A
Figure 26
• DALLAS, TEXAS 75265
2
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
TYPICAL CHARACTERISTICS
SUPPLY CURRENT (ENABLED)
vs
JUNCTION TEMPERATURE
SUPPLY CURRENT (DISABLED)
vs
JUNCTION TEMPERATURE
5
VI(IN) = 5.5 V
65
Supply Current (Disabled) – µ A
Supply Current (Enabled) – µ A
75
VI(IN) = 5 V
55
VI(IN) = 4 V
45
VI(IN) = 3.3 V
VI(IN) = 2.7 V
75
100 125
0
25
50
TJ – Junction Temperature – °C
4
3
2
1
VI(IN) = 4 V
VI(IN) = 3.3 V
0
VI(IN) = 2.7 V
35
–50 –25
VI(IN) = 5.5 V
VI(IN) = 5 V
–1
150
–50 –25
Figure 27
75
100 125
0
25
50
TJ – Junction Temperature – °C
150
Figure 28
SUPPLY CURRENT (ENABLED)
vs
INPUT VOLTAGE
SUPPLY CURRENT (DISABLED)
vs
INPUT VOLTAGE
75
5
TJ = 85°C
Supply Current (Disabled) – µ A
Supply Current (Enabled) – µ A
TJ = 125°C
65
55
45
TJ = 25°C
TJ = 125°C
4
3
TJ = 85°C
2
1
TJ = 25°C
0
TJ = 0°C
TJ = 0°C
TJ = –40°C
TJ = –40°C
35
2.5
3
5
3.5
4
4.5
VI – Input Voltage – V
5.5
6
–1
2.5
3
Figure 29
5.5
6
Figure 30
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
5
3.5
4
4.5
VI – Input Voltage – V
• DALLAS, TEXAS 75265
15
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
TYPICAL CHARACTERISTICS
SHORT-CIRCUIT CURRENT LIMIT
vs
INPUT VOLTAGE
SHORT-CIRCUIT CURRENT LIMIT
vs
JUNCTION TEMPERATURE
3.5
3.5
TPS2024
TPS2024
I OS – Short-Circuit Current Limit – A
I OS – Short-Circuit Current Limit – A
TA = 25°C
3
2.5
TPS2023
2
TPS2022
1.5
1
TPS2021
0.5
TPS2020
3
5
4
VI – Input Voltage – V
2.5
TPS2023
2
6
TPS2022
1.5
TPS2021
1
TPS2020
0.5
0
–50
0
2
3
25
–25
0
50
75
TJ – Junction Temperature – °C
Figure 32
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
vs
INPUT VOLTAGE
60
IO = 0.18 A
50
TJ = 125°C
40
TJ = 25°C
30
TJ = –40°C
20
2.5
3
3.5
4
4.5
5
VI – Input Voltage – V
5.5
6
r DS(on) – Static Drain-Source On-State Resistance – m Ω
r DS(on) – Static Drain-Source On-State Resistance – m Ω
Figure 31
100
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
vs
JUNCTION TEMPERATURE
60
IO = 0.18 A
50
40
VI = 3.3 V
30
20
–50 –25
Figure 33
16
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
VI = 2.7 V
VI = 5.5 V
50
75 100 125
0
25
TJ – Junction Temperature – °C
Figure 34
• DALLAS, TEXAS 75265
150
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
vs
INPUT VOLTAGE
60
IO = 1.8 A
50
TJ = 125°C
40
TJ = 25°C
TJ = –40°C
30
20
3
3.5
4
4.5
5
VI – Input Voltage – V
5.5
6
r DS(on) – Static Drain-Source On-State Resistance – m Ω
r DS(on) – Static Drain-Source On-State Resistance – m Ω
TYPICAL CHARACTERISTICS
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
vs
JUNCTION TEMPERATURE
60
IO = 1.8 A
50
VI = 3.3 V
VI = 4 V
40
VI = 5.5 V
30
20
–50 –25
Figure 35
50
75 100 125
0
25
TJ – Junction Temperature – °C
150
Figure 36
UNDERVOLTAGE LOCKOUT
2.5
VI – Input Voltage – V
2.4
Start Threshold
2.3
2.2
Stop Threshold
2.1
2
–50
0
50
100
TJ – Temperature – °C
150
Figure 37
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
17
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
APPLICATION INFORMATION
TPS2024
2,3
Power Supply
2.7 V to 5.5 V
10 kΩ
IN
0.1 µF
OUT
6,7,8
Load
0.1 µF
5
4
22 µF
OC
EN
GND
1
Figure 38. Typical Application
power-supply considerations
A 0.01-µF to 0.1-µF ceramic bypass capacitor between IN and GND, close to the device, is recommended.
Placing a high-value electrolytic capacitor on the output and input pins is recommended when the output load
is heavy. This precaution reduces power supply transients that may cause ringing on the input. Additionally,
bypassing the output with a 0.01-µF to 0.1-µF ceramic capacitor improves the immunity of the device to
short-circuit transients.
overcurrent
A sense FET checks for overcurrent conditions. Unlike current-sense resistors, sense FETs do not increase the
series resistance of the current path. When an overcurrent condition is detected, the device maintains a
constant output current and reduces the output voltage accordingly. Complete shutdown occurs only if the fault
is present long enough to activate thermal limiting.
Three possible overload conditions can occur. In the first condition, the output has been shorted before the
device is enabled or before VI(IN) has been applied (see Figure 6). The TPS202x senses the short and
immediately switches into a constant-current output.
In the second condition, the excessive load occurs while the device is enabled. At the instant the excessive load
occurs, very high currents may flow for a short time before the current-limit circuit can react (see Figures 13–22).
After the current-limit circuit has tripped (reached the overcurrent trip threshhold) the device switches into
constant-current mode.
In the third condition, the load has been gradually increased beyond the recommended operating current. The
current is permitted to rise until the current-limit threshold is reached or until the thermal limit of the device is
exceeded (see Figures 7–11). The TPS202x is capable of delivering current up to the current-limit threshold
without damaging the device. Once the threshold has been reached, the device switches into its
constant-current mode.
OC response
The OC open-drain output is asserted (active low) when an overcurrent or overtemperature condition is
encountered. The output will remain asserted until the overcurrent or overtemperature condition is removed.
Connecting a heavy capacitive load to an enabled device can cause momentary false overcurrent reporting from
the inrush current flowing through the device, charging the downstream capacitor. An RC filter can be connected
to the OC pin to reduce false overcurrent reporting. Using low-ESR electrolytic capacitors on the output lowers
the inrush current flow through the device during hot-plug events by providing a low impedance energy source,
thereby reducing erroneous overcurrent reporting.
18
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
APPLICATION INFORMATION
TPS202x
TPS202x
GND
OUT
IN
OUT
IN
OUT
EN
V+
Rpullup
OUT
IN
OUT
IN
OUT
EN
OC
V+
GND
Rpullup
Rfilter
OC
Cfilter
Figure 39. Typical Circuit for OC Pin and RC Filter for Damping Inrush OC Responses
power dissipation and junction temperature
The low on-resistance on the n-channel MOSFET allows small surface-mount packages, such as SOIC, to pass
large currents. The thermal resistances of these packages are high compared to those of power packages; it
is good design practice to check power dissipation and junction temperature. The first step is to find rDS(on) at
the input voltage and operating temperature. As an initial estimate, use the highest operating ambient
temperature of interest and read rDS(on) from Figures 33–36. Next, calculate the power dissipation using:
PD
+ rDS(on)
I2
Finally, calculate the junction temperature:
TJ
Where:
+ PD
R qJA
) TA
TA = Ambient Temperature °C
RθJA = Thermal resistance SOIC = 172°C/W, PDIP = 106°C/W
Compare the calculated junction temperature with the initial estimate. If they do not agree within a few degrees,
repeat the calculation, using the calculated value as the new estimate. Two or three iterations are generally
sufficient to get an acceptable answer.
thermal protection
Thermal protection prevents damage to the IC when heavy-overload or short-circuit faults are present for
extended periods of time. The faults force the TPS202x into constant current mode, which causes the voltage
across the high-side switch to increase; under short-circuit conditions, the voltage across the switch is equal
to the input voltage. The increased dissipation causes the junction temperature to rise to high levels. The
protection circuit senses the junction temperature of the switch and shuts it off. Hysteresis is built into the thermal
sense circuit, and after the device has cooled approximately 20 degrees, the switch turns back on. The switch
continues to cycle in this manner until the load fault or input power is removed.
undervoltage lockout (UVLO)
An undervoltage lockout ensures that the power switch is in the off state at powerup. Whenever the input voltage
falls below approximately 2 V, the power switch will be quickly turned off. This facilitates the design of
hot-insertion systems where it is not possible to turn off the power switch before input power is removed. The
UVLO will also keep the switch from being turned on until the power supply has reached at least 2 V, even if
the switch is enabled. Upon reinsertion, the power switch will be turned on, with a controlled rise time to reduce
EMI and voltage overshoots.
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
19
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
APPLICATION INFORMATION
generic hot-plug applications (see Figure 40)
In many applications it may be necessary to remove modules or pc boards while the main unit is still operating.
These are considered hot-plug applications. Such implementations require the control of current surges seen
by the main power supply and the card being inserted. The most effective way to control these surges is to limit
and slowly ramp the current and voltage being applied to the card, similar to the way in which a power supply
normally turns on. Because of the controlled rise times and fall times of the TPS202x series, these devices can
be used to provide a softer start-up to devices being hot-plugged into a powered system. The UVLO feature
of the TPS202x also ensures the switch will be off after the card has been removed, and the switch will be off
during the next insertion. The UVLO feature guarantees a soft start with a controlled rise time for every insertion
of the card or module.
PC Board
TPS2024
Power
Supply
2.7 V to 5.5 V
1000 µF
Optimum
0.1 µF
GND
OUT
IN
OUT
IN
OUT
EN
Block of
Circuitry
OC
Overcurrent Response
Figure 40. Typical Hot-Plug Implementation
By placing the TPS202x between the VCC input and the rest of the circuitry, the input power will reach this device
first after insertion. The typical rise time of the switch is approximately 9 ms, providing a slow voltage ramp at
the output of the device. This implementation controls system surge currents and provides a hot-plugging
mechanism for any device.
20
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
MECHANICAL DATA
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PIN SHOWN
0.050 (1,27)
0.020 (0,51)
0.014 (0,35)
14
0.010 (0,25) M
8
0.008 (0,20) NOM
0.244 (6,20)
0.228 (5,80)
0.157 (4,00)
0.150 (3,81)
Gage Plane
0.010 (0,25)
1
7
0°– 8°
A
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
PINS **
0.004 (0,10)
8
14
16
A MAX
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MIN
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
DIM
4040047 / D 10/96
NOTES: A.
B.
C.
D.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
Falls within JEDEC MS-012
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
21
TPS2020, TPS2021, TPS2022, TPS2023, TPS2024
POWER-DISTRIBUTION SWITCHES
SLVS175A – DECEMBER 1998 – REVISED NOVEMBER 1999
MECHANICAL DATA
P (R-PDIP-T8)
PLASTIC DUAL-IN-LINE PACKAGE
0.400 (10,60)
0.355 (9,02)
8
5
0.260 (6,60)
0.240 (6,10)
1
4
0.070 (1,78) MAX
0.310 (7,87)
0.290 (7,37)
0.020 (0,51) MIN
0.200 (5,08) MAX
Seating Plane
0.125 (3,18) MIN
0.100 (2,54)
0.021 (0,53)
0.015 (0,38)
0°– 15°
0.010 (0,25) M
0.010 (0,25) NOM
4040082 / B 03/95
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-001
22
POST OFFICE BOX 655303
Powered by ICminer.com Electronic-Library Service CopyRight 2003
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright  1999, Texas Instruments Incorporated
Powered by ICminer.com Electronic-Library Service CopyRight 2003