AD ADA4938-1ACPZ-R7

Preliminary Technical Data
FEATURES
Extremely low harmonic distortion
−112 dBc HD2 @ 10 MHz
−79 dBc HD2 @ 50 MHz
−102 dBc HD3 @ 10 MHz
−81 dBc HD3 @ 50 MHz
Low input voltage noise: 2.2 nV/√Hz
High speed
−3 dB bandwidth of 1.5 GHz, G = 1
Slew rate: 4700 V/μs
0.1 dB gain flatness to 125 MHz
Fast overdrive recovery of 4 ns
1 mV typical offset voltage
Externally adjustable gain
Differential to differential or single-ended to differential
operation
Adjustable output common-mode voltage
Wide Supply Voltage Range: +5 V & ± 5 V
Pb-free 3 mm x 3 mm LFCSP package
Ultra-Low Distortion
Differential ADC Driver
ADA4938-1
FUNCTIONAL BLOCK DIAGRAM
+
–
Figure 1.
APPLICATIONS
ADC drivers
Single-ended-to-differential converters
IF and baseband gain blocks
Differential buffers
Line drivers
GENERAL DESCRIPTION
The ADA4938-1 is a low noise, ultra-low distortion, high speed
differential amplifier. It is an ideal choice for driving high
performance ADCs with resolutions up to 16 bits from dc to 70
MHz. The output common mode voltage is adjustable over a
wide range, allowing the ADA4938-1 to match the input of the
ADC. The internal common mode feedback loop also provides
exceptional output balance as well as suppression of even-order
harmonic distortion products.
Full differential and single-ended to differential gain
configurations are easily realized with the ADA4938-1. A
simple external feedback network of four resistors determines
the amplifier’s closed-loop gain.
The ADA4938-1 is fabricated using ADI’s proprietary third
generation high-voltage XFCB process, enabling it to achieve
very low levels of distortion with input voltage noise of only 2.2
nV/√Hz. The low dc offset and excellent dynamic performance
of the ADA4938-1 make it well suited for a wide variety of data
acquisition and signal processing and applications.
The ADA4938-1 is available in a Pb-free, 3 mm x 3mm lead
frame chip scale package (LFCSP). Pinout has been optimized
to facilitate layout and minimize distortion. The part is
specified to operate over the extended industrial temperature
range of −40°C to +85°C.
Rev. PrD
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2007 Analog Devices, Inc. All rights reserved.
ADA4938-1
Preliminary Technical Data
TABLE OF CONTENTS
Features .............................................................................................. 1
Definition of Terms.......................................................................9
Applications....................................................................................... 1
Theory of Operation ...................................................................... 10
Functional Block Diagram .............................................................. 1
Analyzing an Application Circuit ............................................ 10
General Description ......................................................................... 1
Setting the Closed-Loop Gain .................................................. 10
Revision History ............................................................................... 2
Estimating the Output Noise Voltage ...................................... 10
Specifications..................................................................................... 3
The Impact of Mismatches in the Feedback Networks ......... 11
Dual Supply Operation ................................................................ 3
Calculating the Input Impedance of an Application Circuit 11
Single Supply Operation.............................................................. 5
Absolute Maximum Ratings............................................................ 7
Input Common-Mode Voltage Range in Single-Supply
Applications ................................................................................ 11
Thermal Resistance ...................................................................... 7
Setting the Output Common-Mode Voltage .......................... 11
ESD Caution.................................................................................. 7
Layout, Grounding, and Bypassing.............................................. 13
Pin Configuration and Function Descriptions............................. 8
Outline Dimensions ....................................................................... 14
Operational Description.................................................................. 9
Ordering Guide .......................................................................... 14
REVISION HISTORY
05/07—Rev. PrC to Rev. PrD
Changes to Features.......................................................................... 1
Changes to Figure 1.......................................................................... 1
Changes to Table 1............................................................................ 3
Changes to Table 2............................................................................ 5
Changes to Figure 3.......................................................................... 8
Changes to Table 5 ........................................................................... 8
Added to Operational Description Section .................................. 9
Added to Theory of Operation Section ....................................... 10
Added to Layout, Grounding, and Bypassing Section............... 13
04/07—Rev. PrB to Rev. PrC
Changes to Features.......................................................................... 1
Changes to Table 1............................................................................ 3
Changes to Table 2............................................................................ 5
Changes to Table 3............................................................................ 7
Changes to Table 4............................................................................ 7
Added Figure 2 ................................................................................. 7
Changes to Figure 4.......................................................................... 9
Changes to Ordering Guide ............................................................ 9
01/07—Rev. PrA to Rev. PrB
Changes to Features.......................................................................... 1
Changes to General Description .................................................... 1
Changes to Table 1............................................................................ 3
Changes to Table 2............................................................................ 5
12/06—Revision PrA: Initial Version
Rev. PrD | Page 2 of 14
Preliminary Technical Data
ADA4938-1
SPECIFICATIONS
DUAL SUPPLY OPERATION
TA = 25°C, +VS = 5 V, −VS = -5 V, VOCM = 0 V, RT = 61.9 Ω, RG = RF = 200 Ω, G = 1, RL, dm = 1 kΩ, unless otherwise noted.
All specifications refer to single-ended input and differential outputs, unless otherwise noted.
Table 1.
Parameter
±DIN TO ±OUT PERFORMANCE
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Large Signal Bandwidth
Slew Rate
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
Second Harmonic
Third Harmonic
IMD
IP3
Voltage Noise (RTI)
Noise Figure
Input Current Noise
INPUT CHARACTERISTICS
Offset Voltage
Conditions
Min
Input Capacitance
Input Common-Mode Voltage
CMRR
OUTPUT CHARACTERISTICS
Output Voltage Swing
Linear Output Current
Output Balance Error
VOCM to ±OUT PERFORMANCE
VOCM DYNAMIC PERFORMANCE
−3 dB Bandwidth
Slew Rate
Input Voltage Noise (RTI)
VOCM INPUT CHARACTERISTICS
Input Voltage Range
Input Resistance
Input Offset Voltage
Input Bias Current
VOCM CMRR
Gain
POWER SUPPLY
Operating Range
Max
Unit
VOUT = 0.1 V p-p, Differential Input
VOUT = 2 V p-p, Differential Input
VOUT = 2 V p-p, Differential Input
VOUT = 4 V p-p, Differential Input
VOUT = 2 V p-p
VIN = 5 V to 0 V step, G = +2
1500
125
1300
800
4700
4
MHz
MHz
MHz
MHz
V/μs
ns
VOUT = 2 V p-p, 10 MHz
VOUT = 2 V p-p, 50 MHz
VOUT = 2 V p-p, 10 MHz
VOUT = 2 V p-p, 50 MHz
50 MHz
50 MHz
−112
−79
−102
−81
dBc
dBc
dBc
dBc
dBc
dBm
nV/√Hz
dB
pA/√Hz
2.2
21
2
G = +2
VOS, dm = VOUT, dm/2; VDIN+ = VDIN− = 0 V
TMIN to TMAX variation
1
±4
3.5
−0.01
6
3
1
−4.7 to 3.4
−77
Input Bias Current
Input Resistance
Typ
TMIN to TMAX variation
Differential
Common mode
∆VOUT, dm/∆VIN, cm; ∆VIN, cm = ±1 V
Maximum ∆VOUT; single-ended output
-3.9
∆VOUT, cm/∆VOUT, dm; ∆VOUT, dm = 1 V; 10 MHz
95
−66
3.9
V
mA
dB
400
1700
7.5
MHz
V/μs
nV/√Hz
−3.8
∆VOUT, dm/∆VOCM; ∆VOCM = ±1 V
∆VOUT, cm/∆VOCM; ∆VOCM = ±1 V
4.5
Rev. PrD | Page 3 of 14
3.8
200
1
0.5
−75
1
VOS, cm = VOUT, cm; VDIN+ = VDIN– = 0 V
mV
μV/°C
μA
μA/°C
MΩ
MΩ
pF
V
dB
3.5
11
V
kΩ
mV
μA
dB
V/V
V
ADA4938-1
Parameter
Quiescent Current
Power Supply Rejection Ratio
POWER DOWN (PD)
PD Input Voltage
Turn-Off Time
Turn-On Time
PD Bias Current
Enabled
Disabled
Preliminary Technical Data
Conditions
Min
TMIN to TMAX variation
Powered down
∆VOUT, dm/∆VS; ∆VS = ±1 V
Typ
40
40
<1
−90
Max
Unit
mA
μA/°C
mA
dB
Powered down
Enabled
≤1
≥2
1
200
V
V
μs
ns
PD = 5 V
PD = 0 V
40
200
μA
μA
OPERATING TEMPERATURE RANGE
−40
Rev. PrD | Page 4 of 14
+85
°C
Preliminary Technical Data
ADA4938-1
SINGLE SUPPLY OPERATION
TA = 25°C, +VS = 5 V, −VS = 0 V, VOCM = +VS/2, RT = 61.9 Ω, RG = RF = 200 Ω, G = 1, RL, dm = 1 kΩ, unless otherwise noted.
All specifications refer to single-ended input and differential outputs, unless otherwise noted.
Table 2.
Parameter
±DIN TO ±OUT PERFORMANCE
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Large Signal Bandwidth
Slew Rate
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
Second Harmonic
Third Harmonic
IMD
IP3
Voltage Noise (RTI)
Noise Figure
Input Current Noise
INPUT CHARACTERISTICS
Offset Voltage
Conditions
Min
Input Capacitance
Input Common-Mode Voltage
CMRR
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current
Output Balance Error
VOCM TO ±OUT PERFORMANCE
VOCM DYNAMIC PERFORMANCE
−3 dB Bandwidth
Slew Rate
Input Voltage Noise (RTI)
VOCM INPUT CHARACTERISTICS
Input Voltage Range
Input Resistance
Input Offset Voltage
Input Bias Current
VOCM CMRR
Gain
POWER SUPPLY
Operating Range
Quiescent Current
Max
Unit
VOUT = 0.1 V p-p, Differential Input
VOUT = 2 V p-p, Differential Input
VOUT = 2 V p-p, Differential Input
VOUT = 2 V p-p
VIN = 2.5 V to 0 V step, G = +2
1500
125
1100
3900
4
MHz
MHz
MHz
V/μs
ns
VOUT = 2 V p-p, 10 MHz
VOUT = 2 V p-p, 50 MHz
VOUT = 2 V p-p, 10 MHz
VOUT = 2 V p-p, 50 MHz
50 MHz
50 MHz
−110
−79
−100
−79
dBc
dBc
dBc
dBc
dBc
dBm
nV/√Hz
dB
pA/√Hz
2.2
21
2
G = +2
VOS, dm = VOUT, dm/2; VDIN+ = VDIN− = VOCM = 2.5 V
TMIN to TMAX variation
1
±4
3.5
−0.01
6
3
1
0.3 to 3.4
−77
Input Bias Current
Input Resistance
Typ
TMIN to TMAX variation
Differential
Common mode
∆VOUT, dm/∆VIN, cm; ∆VIN, cm = ±1 V
Maximum ∆VOUT; single-ended output
1.1
∆VOUT, cm/∆VOUT, dm; ∆VOUT, dm = 1 V
V = 0.5 V
95
−66
3.9
V
mA
dB
400
1700
7.5
MHz
V/μs
nV/√Hz
1.2
∆VOUT, dm/∆VOCM; ∆VOCM = ±1 V
∆VOUT, cm/∆VOCM; ∆VOCM = ±1 V
4.5
Rev. PrD | Page 5 of 14
3.8
V
kΩ
mV
μA
dB
V/V
11
V
mA
μA/°C
mA
200
1
0.5
−75
1
VOS, cm = VOUT, cm; VDIN+ = VDIN– = VOCM = 2.5 V
TMIN to TMAX variation
Powered down
mV
μV/°C
μA
μA/°C
MΩ
MΩ
pF
V
dB
36
40
<1
ADA4938-1
Parameter
Power Supply Rejection Ratio
POWER DOWN (PD)
PD Input Voltage
Turn-Off Time
Turn-On Time
PD Bias Current
Enabled
Disabled
Preliminary Technical Data
Conditions
∆VOUT, dm/∆VS; ∆VS = ±1 V
Min
Powered down
Enabled
PD = 5 V
PD = 0 V
OPERATING TEMPERATURE RANGE
−40
Rev. PrD | Page 6 of 14
Typ
−90
Max
Unit
dB
≤1
≥2
1
200
V
V
μs
ns
20
−120
μA
μA
+85
°C
Preliminary Technical Data
ADA4938-1
ABSOLUTE MAXIMUM RATINGS
Table 3.
Rating
12 V
See Figure 2
−65°C to +125°C
−40°C to +85°C
300°C
150°C
Stresses above those listed under Absolute Maximum
Rating may cause permanent damage to the device. This is
a stress rating only; functional operation of the device at
these or any other conditions above those indicated in the
operational section of this specification is not implied.
Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
Airflow increases heat dissipation, effectively reducing θJA. In
addition, more metal directly in contact with the package
leads/exposed pad from metal traces, through-holes, ground,
and power planes reduces the θJA.
Figure 2 shows the maximum safe power dissipation in the
package vs. the ambient temperature for the 16-lead LFCSP
(95 °C/W) on a JEDEC standard 4-layer board.
THERMAL RESISTANCE
2.0
Table 4. Thermal Resistance
Package Type
16-Lead LFCSP (Exposed Pad)
θJA
95
Unit
°C/W
Maximum Power Dissipation
The maximum safe power dissipation in the ADA4938-1
package is limited by the associated rise in junction
temperature (TJ) on the die. At approximately 150°C, which
is the glass transition temperature, the plastic changes its
properties. Even temporarily exceeding this temperature
limit can change the stresses that the package exerts on the
die, permanently shifting the parametric performance of
the ADA4938-1. Exceeding a junction temperature of 150°C
for an extended period can result in changes in the silicon
devices, potentially causing failure.
1.8
MAXIMUM POWER DISSIPATION (W)
θJA is specified for the device (including exposed pad)
soldered to a high thermal conductivity 2s2p circuit board,
as described in EIA/JESD 51-7.
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
–45 –35 –25 –15 –5
5
15 25 35 45 55 65 75 85 95 105
AMBIENT TEMPERATURE (°C)
06591-003
Parameter
Supply Voltage
Power Dissipation
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
Junction Temperature
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive. The quiescent power is the
voltage between the supply pins (VS) times the quiescent
current (IS). The power dissipated due to the load drive depends
upon the particular application. The power due to load drive is
calculated by multiplying the load current by the associated
voltage drop across the device. RMS voltages and currents must
be used in these calculations.
Figure 2. Maximum Power Dissipation vs. Temperature for a 4-Layer Board
ESD CAUTION
Rev. PrD | Page 7 of 14
ADA4938-1
Preliminary Technical Data
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 3. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
2
3
4
5 to 8
9
10
11
12
13 to 16
Mnemonic
−FB
+IN
−IN
+FB
+VS
VOCM
+OUT
−OUT
PD
−VS
Description
Negative Output for Feedback Component Connection
Positive Input Summing Node
Negative Input Summing Node
Positive Output for Feedback Component Connection
Positive Supply Voltage
Output Common-Mode Voltage
Positive Output for Load Connection
Negative Output for Load Connection
Power-Down Pin
Negative Supply Voltage
Rev. PrD | Page 8 of 14
Preliminary Technical Data
ADA4938-1
OPERATIONAL DESCRIPTION
Common-Mode Voltage
DEFINITION OF TERMS
This refers to the average of two node voltages. The output
common-mode voltage is defined as
VOUT, cm = (V+OUT + V−OUT)/2
Balance
Figure 4. Circuit Definitions
Differential Voltage
This refers to the difference between two node voltages. For
example, the output differential voltage (or equivalently, output
differential-mode voltage) is defined as
Balance is a measure of how well differential signals are
matched in amplitude and are exactly 180° apart in phase.
Balance is most easily determined by placing a well-matched
resistor divider between the differential voltage nodes and
comparing the magnitude of the signal at the divider’s midpoint
with the magnitude of the differential signal. By this definition,
output balance is the magnitude of the output common-mode
voltage divided by the magnitude of the output differential
mode voltage.
VOUT, dm = (V+OUT − V−OUT)
where V+OUT and V−OUT refer to the voltages at the +OUT and
−OUT terminals with respect to a common reference.
Rev. PrD | Page 9 of 14
Output Balance Error =
VOUT , cm
VOUT , dm
ADA4938-1
Preliminary Technical Data
THEORY OF OPERATION
The ADA4938-1 differs from conventional op amps in that it
has two outputs whose voltages move in opposite directions.
Like an op amp, it relies on open-loop gain and negative
feedback to force these outputs to the desired voltages. The
ADA4938-1 behaves much like a standard voltage feedback op
amp and makes it easier to perform single-ended-to-differential
conversions, common-mode level shifting, and amplifications
of differential signals. Also like an op amp, the ADA4938-1 has
high input impedance and low output impedance.
Two feedback loops are employed to control the differential and
common-mode output voltages. The differential feedback, set
with external resistors, controls only the differential output
voltage. The common-mode feedback controls only the commonmode output voltage. This architecture makes it easy to set the
output common-mode level to any arbitrary value. It is forced,
by internal common-mode feedback, to be equal to the voltage
applied to the VOCM input, without affecting the differential
output voltage.
The ADA4938-1 architecture results in outputs that are highly
balanced over a wide frequency range without requiring tightly
matched external components. The common-mode feedback
loop forces the signal component of the output commonmode voltage to zero. This results in nearly perfectly balanced
differential outputs that are identical in amplitude and are
exactly 180° apart in phase.
SETTING THE CLOSED-LOOP GAIN
The differential-mode gain of the circuit in Figure 4 can be
determined by
VOUT , dm
VIN , dm
=
RF
RG
This assumes the input resistors (RG) and feedback resistors (RF)
on each side are equal.
ESTIMATING THE OUTPUT NOISE VOLTAGE
The differential output noise of the ADA4938-1 can be
estimated using the noise model in Figure 5. The input-referred
noise voltage density, vnIN, is modeled as a differential input, and
the noise currents, inIN− and inIN+, appear between each input and
ground. The noise currents are assumed to be equal and
produce a voltage across the parallel combination of the gain
and feedback resistances. vnCM is the noise voltage density at the
VOCM pin. Each of the four resistors contributes (4kTRx)1/2. Table
6 summarizes the input noise sources, the multiplication factors,
and the output-referred noise density terms.
VnRG1
RG1
inIN+
+
inIN–
ANALYZING AN APPLICATION CIRCUIT
The ADA4938-1 uses open-loop gain and negative feedback to
force its differential and common-mode output voltages in such
a way as to minimize the differential and common-mode error
voltages. The differential error voltage is defined as the voltage
between the differential inputs labeled +IN and −IN (see
Figure 4). For most purposes, this voltage can be assumed to be
zero. Similarly, the difference between the actual output
common-mode voltage and the voltage applied to VOCM can also
be assumed to be zero. Starting from these two assumptions,
any application circuit can be analyzed.
VnRF1
RF1
VnIN
ADA4938-1
VnOD
VOCM
VnCM
VnRG2
RG2
RF2
VnRF2
Figure 5. ADA4938-1 Noise Model
Table 6. Output Noise Voltage Density Calculations
Input Noise Contribution
Differential Input
Inverting Input
Noninverting Input
VOCM Input
Gain Resistor RG1
Gain Resistor RG2
Feedback Resistor RF1
Feedback Resistor RF2
Input Noise Term
vnIN
inIN−
inIN+
vnCM
vnRG1
vnRG2
vnRF1
vnRF2
Input Noise
Voltage Density
vnIN
inIN− × (RG2||RF2)
inIN+ × (RG1||RF1)
vnCM
(4kTRG1)1/2
(4kTRG2)1/2
(4kTRF1)1/2
(4kTRF2)1/2
Rev. PrD | Page 10 of 14
Output
Multiplication Factor
GN
GN
GN
GN(β1 − β2)
GN(1 − β2)
GN(1 − β1)
1
1
Output Noise
Voltage Density Term
vnO1 = GN(vnIN)
vnO2 = GN[inIN− × (RG2||RF2)]
vnO3 = GN[inIN+ × (RG1||RF1)]
vnO4 = GN(β1 − β2)(vnCM)
vnO5 = GN(1 − β2)(4kTRG1)1/2
vnO6 = GN(1 − β1)(4kTRG2)1/2
vnO7 = (4kTRF1)1/2
vnO8 = (4kTRF2)1/2
Preliminary Technical Data
ADA4938-1
Similar to the case of a conventional op amp, the output noise
voltage densities can be estimated by multiplying the inputreferred terms at +IN and −IN by the appropriate output factor,
where:
GN =
β1 =
2
(β1 + β2 )
is the circuit noise gain.
RG1
RG2
and β2 =
are the feedback factors.
RF1 + RG1
RF2 + RG2
When RF1/RG1 = RF2/RG2, then β1 = β2 = β, and the noise gain
becomes
GN =
1
R
=1+ F
β
RG
Figure 6. ADA4938-1 Configured for Balanced (Differential) Inputs
For an unbalanced, single-ended input signal (see Figure 7), the
input impedance is
Note that the output noise from VOCM goes to zero in this case.
The total differential output noise density, vnOD, is the root-sumsquare of the individual output noise terms.
vnOD =
RIN , cm
⎛
⎞
⎜
⎟
R
G
⎟
=⎜
RF
⎜1−
⎟
⎜
⎟
(
)
×
+
2
R
R
F ⎠
G
⎝
8
2
∑ vnOi
i =1
THE IMPACT OF MISMATCHES IN THE FEEDBACK
NETWORKS
As previously mentioned, even if the external feedback networks
(RF/RG) are mismatched, the internal common-mode feedback
loop still forces the outputs to remain balanced. The amplitudes
of the signals at each output remain equal and 180° out of phase.
The input-to-output, differential mode gain varies proportionately
to the feedback mismatch, but the output balance is unaffected.
As well as causing a noise contribution from VOCM, ratio
matching errors in the external resistors result in a degradation
of the ability of the circuit to reject input common-mode signals,
much the same as for a four-resistor difference amplifier made
from a conventional op amp.
In addition, if the dc levels of the input and output commonmode voltages are different, matching errors result in a small
differential-mode output offset voltage. When G = 1, with a
ground referenced input signal and the output common-mode
level set to 2.5 V, an output offset of as much as 25 mV (1% of
the difference in common-mode levels) can result if 1% tolerance
resistors are used. Resistors of 1% tolerance result in a worstcase input CMRR of about 40 dB, a worst-case differentialmode output offset of 25 mV due to 2.5 V level-shift, and no
significant degradation in output balance error.
CALCULATING THE INPUT IMPEDANCE OF AN
APPLICATION CIRCUIT
The effective input impedance of a circuit depends on whether
the amplifier is being driven by a single-ended or differential
signal source. For balanced differential input signals, as shown
in Figure 6, the input impedance (RIN, dm) between the inputs
(+DIN and −DIN) is simply RIN, dm = 2 × RG.
Figure 7. ADA4938-1 Configured for Unbalanced (Single-Ended) Input
The input impedance of the circuit is effectively higher than it
would be for a conventional op amp connected as an inverter
because a fraction of the differential output voltage appears at
the inputs as a common-mode signal, partially bootstrapping
the voltage across the input resistor RG.
INPUT COMMON-MODE VOLTAGE RANGE IN
SINGLE-SUPPLY APPLICATIONS
The ADA4938-1 is optimized for level-shifting, ground-referenced
input signals. As such, the center of the input common-mode
range is shifted approximately 1 V down from midsupply. For
5 V single-supply operation, the input common-mode range at
the summing nodes of the amplifier is 0.3 V to 3.0 V. To avoid
clipping at the outputs, the voltage swing at the +IN and –IN
terminals must be confined to these ranges.
SETTING THE OUTPUT COMMON-MODE VOLTAGE
The VOCM pin of the ADA4938-1 is internally biased at a voltage
approximately equal to the midsupply point (average value of
the voltages on V+ and V−). Relying on this internal bias results
in an output common-mode voltage that is within about 100 mV of
the expected value.
In cases where more accurate control of the output commonmode level is required, it is recommended that an external
source, or resistor divider (10 kΩ or greater resistors), be used.
It is also possible to connect the VOCM input to a common-mode
level (CML) output of an ADC. However, care must be taken to
Rev. PrD | Page 11 of 14
ADA4938-1
Preliminary Technical Data
assure that the output has sufficient drive capability. The input
impedance of the VOCM pin is approximately 10 kΩ. If multiple
ADA4938-1 devices share one reference output, it is
recommended that a buffer be used.
Table 7 and Table 8 list several common gain settings,
associated resistor values, input impedance, output noise
density, and approximate large signal bandwidth for both balanced
and unbalanced input configurations. Also shown are the input
common-mode voltage swings under the given conditions for
different VOCM settings with both dual and single 5 V supplies.
Table 7. Differential Ground-Referenced Input, DC-Coupled; See Figure 6
Nominal
Gain (dB)
0
3
6
10
12
14
RF (Ω)
200
348
280
348
200
348
316
348
402
348
499
348
RG (Ω)
200
348
200
249
100
174
100
110
100
86.6
100
69.8
RIN, dm(Ω)
400
696
400
498
200
348
200
220
200
173
200
140
Differential
Output
Noise Density
(nV/√Hz)
5.8
6.7
7.2
7.6
8.0
9.0
11
12
14
13
17
16
Approximate
Large-Signal
Bandwidth (MHz)
Common-Mode Swing at +IN, −IN (V)
+VS = 5 V, -VS = -5 V
VOUT, dm = 2.0 V p-p
VOCM = 3.5 V
VOCM = 0 V
-0.50 to 0.50 1.25 to 2.25
+VS =5 V
VOUT, dm = 2.0 V p-p
VOCM = 2.5 V
VOCM = 3.2 V
0.75 to 1.75
1.10 to 2.10
-0.35 to 0.35
1.10 to 1.82
0.69 to 1.40
0.98 to 1.69
-0.25 to 0.25
0.92 to 1.42
0.58 to 1.08
0.82 to 1.32
-0.16 to 0.16
0.68 to 1.00
0.44 to 0.76
0.61 to 0.92
-0.13 to 0.13
0.57 to 0.82
0.37 to 0.62
0.51 to 0.76
-0.10 to 0.10
0.48 to 0.68
0.32 to 0.52
0.43 to 0.63
Table 8. Single-Ended Ground-Referenced Input, DC-Coupled, RS = 50 Ω; See Figure 7
Nominal
Gain (dB)
0
3
6
10
12
14
1
RF
(Ω)
200
348
280
348
200
348
316
348
402
348
499
348
RG1
(Ω)
200
348
200
249
100
174
100
110
100
86.6
100
69.8
RT
(Ω)
61.9
56.2
60.4
59.0
75.0
61.9
73.2
69.8
71.5
76.8
71.5
86.6
RIN,cm
(Ω)
267
464
282
351
150
261
161
177
167
144
171
120
RG2
(Ω)1
226
374
226
274
130
200
130
140
130
118
130
100
Differential
Output
Noise
Density
(nV/√Hz)
5.5
6.5
6.8
7.3
7.0
8.4
9.7
10
12
11
14
12
Approximate
Large-Signal
Bandwidth
(MHz)
RG2 = RG1 + (RS||RT)
Rev. PrD | Page 12 of 14
Common-Mode Swing at +IN, -IN (V)
+VS =5 V
+VS = 5 V, -VS = -5 V
VOUT,dm = 2.0 V p-p
VOUT, dm = 2.0 V p-p
VOCM = 3.5 V VOCM = 2.5 V VOCM = 3.2 V
VOCM = 0 V
-0.56 to 0.56
1.29 to 2.42
0.75 to 1.75
1.13 to 2.26
-0.40 to 0.40
1.16 to 1.97
0.71 to 1.52
1.03 to 1.83
-0.33 to 0.33
1.05 to 1.70
0.66 to 1.31
0.94 to 1.59
-0.21 to 0.21
0.82 to 1.23
0.52 to 0.93
0.73 to 1.14
-0.16 to 0.16
0.70 to 1.02
0.45 to 0.77
0.62 to 0.94
-0.13 to 0.13
0.59 to 0.85
0.39 to 0.65
0.53 to 0.79
Preliminary Technical Data
ADA4938-1
LAYOUT, GROUNDING, AND BYPASSING
As a high speed device, the ADA4938-1 is sensitive to the
PCB environment in which it operates. Realizing its superior
performance requires attention to the details of high speed
PCB design.
Signal routing should be short and direct to avoid parasitic
effects. Wherever complementary signals exist, a symmetrical
layout should be provided to maximize balanced performance.
When routing differential signals over a long distance, PCB
traces should be close together, and any differential wiring
should be twisted such that loop area is minimized. This
reduces radiated energy and makes the circuit less susceptible
to interference.
06591-052
The first requirement is a solid ground plane that covers as
much of the board area around the ADA4938-1 as possible.
However, the area near the feedback resistors (RF), gain resistors
(RG), and the input summing nodes (Pin 2 and Pin 3) should be
cleared of all ground and power planes (see Figure 8). This
minimizes any stray capacitance at these nodes and prevents
peaking of the response of the amplifier at high frequencies.
The power supply pins should be bypassed as close to the device
as possible and directly to a nearby ground plane. High frequency
ceramic chip capacitors should be used. It is recommended that
two parallel bypass capacitors (1000 pF and 0.1 μF) be used for
each supply. The 1000 pF capacitor should be placed closer to
the device. Further away, low frequency bypassing should be
provided, using 10 μF tantalum capacitors from each supply
to ground.
Figure 8. Ground and Power Plane Voiding in Vicinity of RF and RG
Rev. PrD | Page 13 of 14
ADA4938-1
Preliminary Technical Data
OUTLINE DIMENSIONS
3.00
BSC SQ
0.60 MAX
13
12
0.45
PIN 1
INDICATOR
TOP
VIEW
2.75
BSC SQ
0.80 MAX
0.65 TYP
12° MAX
SEATING
PLANE
16
1
PIN 1
INDICATOR
*1.45
1.30 SQ
1.15
EXPOSED
PAD
0.50
BSC
1.00
0.85
0.80
0.50
0.40
0.30
9
(BOTTOM VIEW) 4
8
5
0.25 MIN
1.50 REF
0.05 MAX
0.02 NOM
0.30
0.23
0.18
0.20 REF
*COMPLIANT TO JEDEC STANDARDS MO-220-VEED-2
EXCEPT FOR EXPOSED PAD DIMENSION.
Figure 9. 16-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
3 mm × 3 mm Body
(CP-16-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADA4938-1ACPZ-R2
ADA4938-1ACPZ-RL
ADA4938-1ACPZ-R7
Ordering Quantity
5,000
1,500
250
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
PR06592-0-6/07(PrD)
Package Description
16-Lead 3 mm × 3 mm LFCSP
16-Lead 3 mm × 3 mm LFCSP
16-Lead 3 mm × 3 mm LFCSP
Package Option
CP-16-2
CP-16-2
CP-16-2
Branding
TBD
TBD
TBD