NJL71H/71V/72H/73H/74H000 INFRARED REMOTE CONTROL RECEIVER ■ GENERAL DESCRIPTION The NJL70H/V000 series are small and high performance receiving devices for infrared remote control system. They can operate under low and wide supply voltage (2.4V to 5.4V). Also, their supply current is low comparing to the NJL60H/V000 and NJL80H/V000. The features, low and wide supply voltage, low supply current are suitable for battery operated items ■ FEATURES 1. Wide and low supply voltage 2.4V to 5.5V 2. Low supply current 0.6mA max. 3. Mold type and metal case type to meet the design of front panel. 4. Line-up for various center carrier frequencies. ■ APPLICATIONS 1. AV instruments such as Audio, TV, VCR, CD, MD etc. 2. Home application such as Air-conditioner, Fan etc. 3. Battery operated instruments such as Toy, Camera etc. ■ LINE-UP Mold/Metal case View Hight Mold type Top Metal Case type Top Side Carrier 5.4mm 6.3mm 8mm Frequency fo= 36 kHz NJL71H360 NJL71V360 NJL72H360 36.7 kHz NJL71H367 NJL71V367 NJL72H367 38 kHz NJL71H380 NJL71V380 NJL72H380 40 kHz NJL71H400 NJL71V400 NJL72H400 Regarding other frequency or packages, please contact to New JRC individually. 11mm NJL73H360 NJL73H367 NJL73H380 NJL73H400 15mm NJL74H360 NJL74H367 NJL74H380 NJL74H400 ■ BLOCK DIAGRAM Vcc Head Amp 2nd Amp Comparator 3rd Amp 22K Vout B.P.F. Detector PD ABLC GND ■ ABSOLUTE MAXIMUM RATINGS (Ta=25°C) PARAMETER Supply Voltage Operating Temperature Range Storage Temperature Range Soldering Temperature SYMBOL Vcc Topr Tstg Tsol RATINGS 6.3 -20 to +75 -40 to +85 260 (5sec. 4.0mm from mold body) UNIT V °C °C °C -1- NJL71H/71V/72H/73H/74H000 ■ RECOMMENDED OPERATING CONDITION Supply Voltage Range Vcc 2.4 V to 5.5V ■ ELECTRO-OPTICAL CHARACTERISTICS (Vcc=3.3V, Ta=25°C) PARAMETER Supply Current Transmission Distance Directivity SYMBOL Icc Lc θL θV VL VH TwL TwH fo Output Voltage Low Output Voltage High Low Level Pulse Width High Level Pulse Width Center Frequency TEST CONDITION No Signal Input Direction of Ray Axis *1 Angle of half Lc, Horizontal *2 Angle of half Lc, Vertical *2 No Load No Load See Test Circuit See Test Circuit See Line-up MIN — 8 — — — 2.8 350 400 36.0 TYP 0.43 16 45 30 0.2 — — — — MAX 0.6 — — — 0.5 — 800 850 40.0 UNIT mA m deg deg V V µs µs kHz Note *1:Test with each center carrier frequency under the test condition shown below. *2:Place major axis of elliptic lens in horizontal direction and minor vertical. ■ TEST METHOD Carrier frequency is adjusted to center frequency of each product Test condition in as follows: IR TRANSMITTER (1) Standard transmitter: Transmitting waveform is shown in Fig.1 Transmitting power should be adjusted so that output voltage Vout will be 400mVp-p.(Test circuit is shown in Fig.2) Regarding IR LED used for transmitter, λp=940nm, ∆λ=50nm. OUTPUT WAVE FORM 600us 600us VH OUTPUT PULSE TWH TWL OF DEVICE VL Regarding photo diode, Sensitivity S=26nA/Lx in case light source temperature2856°K, Ee=100Lx, VR=5V Fig.1 TRANSMITTER WAVE FORM 20cm 10K 4.9 - 5.1V (2) Test system: Shown in Fig.3. + - 100K Vout SENSING DISTANCE : L Vcc OUT Vout STANDARD TRANSMITTER Fig.3 TEST SYSTEM -2- GND Fig.2 STD.TRANSMITTER TEST CIRCUIT NJL71H/71V/72H/73H/74H000 ■ TYPICAL CHARACTRISTICS Spectral Response (Ta=25°C) Directivity (Ta=25℃) 100 90 90 Relative Transmission Distance (%) 100 Relative Responsibirity (%) 80 70 60 50 40 30 20 10 80 70 60 50 40 30 20 10 0 0 600 700 800 900 1000 -60 1100 -50 -40 -30 -20 -10 0 10 Horizontal Output Pulse Width vs. Distance (Input Pulse Width=600μs, Vcc=3.3V, Ta=25℃) 30 40 50 60 Vertical Transmission Distance vs. Supply Voltage (Ta=25°C) 850 20 750 650 550 450 350 0 2 4 6 8 10 12 14 16 18 Transmission Distance Lc (m) Transmision Distance Lc (m) Output Pulse Width TwL (μs) 20 Angle θ (deg) Wavelength (nm) 18 16 14 12 10 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Supply Voltage Vcc (V) Transmission Distance vs. Temperature (Vcc=3.3V) Transmission Distance vs.Carrier Frequency (Vcc=3.3V, Ta=25°C) 90 80 70 60 50 24 26 28 30 32 34 36 38 40 42 44 Carrier Frequency (kHz) fo=36kHz fo=40kHz 46 48 50 Transmission Distance Lc (m) Relative Distance (%) 100 20 18 16 14 12 10 8 -40 -20 0 20 40 60 80 100 Ambient temperature Ta (℃） -3- NJL71H/71V/72H/73H/74H000 ■ RECOMMENDED APPLICATION CIRCUIT 1 : OUT 2 : GND 3 : Vcc 47Ω 1 2 3 Vcc 47uF RC Filter should be connected closely between Vcc pin and GND pin. ■ OUTLINE 5.4 5.4 6.2 2.6 1.6 2.2 4.7 7.3 0.4 1.6 0.5 2.2 3.2 2.5 4.7 7.3 2.6 2.2 3.2 4.0 1.0 2.54 2.54 0.5 1 : OUT 2 : GND 3 : Vcc 2.54 2.54 1 2 3 1 2 3 NJL71H000 UNIT:mm NJL71V000 UNIT:mm 5.4 6.2 0.5 1.6 0.4 2.5 4.7 7.3 2.6 2.2 3.2 2.54 2.54 2.2 1.0 13.1 1 : OUT 2 : GND 3 : Vcc 1 2 3 NJL71H000F3 UNIT:mm -4- 2.2 1.0 16.5±0.5 6.2 1 : OUT 2 : GND 3 : Vcc 0.4 NJL71H/71V/72H/73H/74H000 11.0 8.0 2.54 2.54 0.3 3.5 2.0 (12.6) 8.2 2.0 1 2 3 2.54 0.5 2.0 3 - φ 0.8 2.54 1.3 PCB Pattern NJL72H000 UNIT:mm 2.54 2.54 1 2 3 6.7 2.5 8.2 6.7 0.5 1.3 1 : OUT 2 : GND 3 : Vcc 2.5 0.3 (9.6) 3.5 9.1 10.2 2.0 1 : OUT 2 : GND 3 : Vcc 0.4 2.54 8.0 3.5 3.0 10.2 8.0 2.54 1.9 7.0 3.5 0.4 6.1 3.0 1.9 7.0 3 - φ 0.8 PCB Pattern NJL73H000 UNIT:mm 15.0 1.9 3.5 13.1 3.5 1 : OUT 2 : GND 3 : Vcc (16.6) 8.2 2.0 6.7 2.5 0.3 0.4 2.54 2.54 2.0 10.2 8.0 3.0 7.0 0.5 2.54 2.54 3 - φ 0.8 PCB Pattern 1.3 1 2 3 1. Tolerance is ±0.3mm unless otherwise noted. 2. Ground metal case on PCB. Metal case is not connected to GND pin inside. NJL74H000 UNIT:mm [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. -5-