RM/8000/M ISO Cylinders Magnetic Piston Double Acting Ø 10 to 25 mm ● Magnetic piston as standard ● Conforming to ISO 6432 ● Corrosion resistance ● Buffer and adjustable cushioned models ● Supplied complete with nose mounting nut and piston rod locknut Ordering Examples Technical Data Medium: Compressed air, filtered, lubricated or non-lubricated Standard: ISO 6432 Operation: Double acting with buffer or adjustable cushioning Operating Pressure: 1 to 10 bar Operating Temperature: -10°C* to +80˚C max. See page N 1.5.021.03 Mountings and Switches See page N 1.5.021.03 Alternative Models Single acting cylinders See page N 1.4.031.01 *Consult our Technical Service for use below +2°C Cylinder Diameters: 10, 12, 16, 20, 25 mm (buffer cushioning) 16, 20, 25 mm (adjustable cushioning) Strokes: Standard, see page N 1.5.021.02 Non-standard strokes (500 mm max.) available Materials: Barrel: Stainless steel (Austenitic) End covers: Clear anodised aluminium alloy Piston rod: Stainless steel (Austenitic) Buffer: Polyurethane Wiper: Polyurethane Seals: Nitrile rubber 10/97 Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. N 1.5.021.01 RM/8000/M Cylinder Variants Symbol Model non-magnetic piston Symbol TRM/8000 Model magnetic piston RM/8000/M RM/8000/MC RM/8000/MF — RM/8000/MU Description Dimensions Page 04 04 04 04 04 Standard cylinders Cylinders with central rear port Cylinders with flat rear cover Cylinders with heat resistant seal (150˚C max.) Cylinders with extended piston rod RM/8017/M RM/8021/M RM/8026/M RM/8000/JM Cylinder ∅ 16 mm with adjustable cushioning Cylinder ∅ 20 mm with adjustable cushioning Cylinder ∅ 25 mm with adjustable cushioning Cylinder with double ended piston rod (∅ 16 to 25 mm) 05 RM/8000/N2 Cylinders with non-rotating piston rod (∅ 12 to 25 mm) 05 RM/8000/L4 Cylinder ∅ 12 to 25 mm with locking unit (PASSIVE). Locking is achieved by spring force on removal of the signal to the unit. Operating pressure for locking unit: 4 to 10 bar 05 04 For combinations of cylinder variants consult our Technical Service. Standard Strokes (buffer cushioned models) Cylinder ∅ 10 12 16 20 25 Strokes (mm) 10 25 ● ● ● ● ● ● ● ● ● ● 40 ● ● ● ● ● 50 ● ● ● ● ● 80 ● ● ● ● ● 100 ● ● ● ● ● 125 160 200 250 ● ● ● ● ● ● ● ● ● ● ● ● ● ● Special Variants (only non-magnetic piston) Heat resistant seals, 150°C max. 16 20 25 Cylinder ∅ 10 12 16 20 25 Strokes (mm) 10 25 40 50 80 100 125 160 200 250 ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ✶RM/80✶✶/✶✶/✶✶✶ Model Codes Cylinder Diameters (mm) Standard Strokes (adjustable cushioned models) Substitute T Substitute 10, 12, 16, 20, 25 Adjustable cushioned models 17 21 26 Strokes (mm) 500 max. Variants (non-magnetic piston) Extended piston rod Substitute IU Variants (magnetic piston) Standard Central rear port Flat rear cover Extended piston rod Non-rotating piston rod Double ended piston rod Locking unit Substitute M MC MF MU N2 JM L4 Note: If option is not required, disregard option position within part number eg. RM/8020/M/25. For combinations of cylinder variants consult our Technical Service. Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressures and temperatures can exceed those listed under ‘Technical Data’. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult NORGREN. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. N 1.5.021.02 The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products. Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. 10/97 RM/8000/M Mountings Style ‘AK’ Style ‘B’, ‘G’ Style ‘C’ Style ‘F’ Style ‘FH’ Style ‘L’ Style ‘L2’ Cylinder ∅ 10 12 16 20 25 Page 07 QM/8010/38 QM/8012/38 QM/8012/38 QM/8020/38 QM/8025/38 Style ‘N’ Page 06 M/P19407 M/P19408 M/P19408 M/P19409 M/P19409 Style ‘UF’ Page 06 M/P19369 M/P19389 M/P19389 M/P19406 M/P19406 Guide Blocks Page 07 QM/8010/25 QM/8012/25 QM/8012/25 QM/8020/25 QM/8025/25 Locking Units ‘Passive’ Page 10 — QM/8012/34 QM/8012/34 QM/8020/34 QM/8020/34 Bracket for Switches # ≥ 15 mm stroke Page 06 QM/947 QM/8012/24 QM/8012/24 QM/8020/24 QM/8020/24 Bracket for Switches # < 15 mm stroke Page 07 QM/8010/44 QM/8012/44 QM/8012/44 QM/8020/44 QM/8020/44 Bracket for Switches ## Cylinder ∅ 10 12 16 20 25 Page 09 M/P1501/90 M/P13834 M/P13834 M/P13615 M/P13615 Page 07 QM/8010/32 QM/8012/32 QM/8012/32 QM/8020/32 QM/8025/32 Page 08 — QM/8012/61/* QM/8012/61/* QM/8020/61/* QM/8025/61/* Page 05 — QM/8012/59 QM/8012/59 QM/8020/59 QM/8025/59 Page 10 QM/33/010/22 QM/33/012/22 QM/33/016/22 QM/33/020/22 QM/33/025/22 Page 10 QM/33/010/23 QM/33/016/23 QM/33/016/23 QM/33/020/23 QM/33/025/23 Page 10 QM/45/210/22 QM/45/212/22 QM/45/216/22 QM/45/220/22 QM/45/225/22 * Insert standard stroke length (50, 100, 160, 200, 250; optional 320, 400, 500) in mm # QM/33, QM/34 or QM/134 ## QM/45 Switches Model Reed Reed Solid state Model Reed QM/33/** QM/33/C/** QM/34/** QM/34/P QM/34/S/** QM/34/N/** QM/45/RAP/** QM/45/LAP/** QM/45/LSU/** — — — — — — — ∅ 8 mm QM/33 — — Solid state — — — — — — — — QM/45/EAP/** QM/134/** QM/134/P QM/134/E/** QM/134/N/** QM/134/N/P QM/134/X/** ∅ 5 mm QM/45/RAP — — Voltage V a.c. 10 to 240 10 to 110 — — 10 to 240 — 10 to 30 — 10 to 240 — — — — — — — ∅ 8 mm QM/34 — QM/134 V d.c. 10 to 240 10 to 175 10 to 30 10 to 30 10 to 240 10 to 30 10 to 30 10 to 30 10 to 170 10 to 30 10 to 30 10 to 30 10 to 30 10 to 30 10 to 30 8,2 ∅ 5 mm QM/45/LAP QM/45/LSU QM/45/EAP Current Max. 1,5 A 0,25 A 1A 1A 0,5 A 1A 0,5 A 0,5 A 0,18 A 0,2 A 0,2 A 0,2 A 0,2 A 0,2 A 0,2 A 2,2 /1 mA Temperature °C -20° to +80° -20° to +80° -20° to +80° -20° to +80° -20° to +80° -20° to +80° -20° to +80° -20° to +80° -20° to +80° -20° to +80° -20° to +80° -20° to +80° -20° to +80° -20° to +80° -20° to +80° -25° to +75° ∅ 8 mm QM/34/P — QM/134/P LED — — ● ● ● ● — ● ● ● ● ● ● ● ● ● — — — — Features — Changeover Output: Positive Output: Positive — Output: Negative — — — PNP PNP PNP Pulse strecher NPN NPN NAMUR Cable Length 2, 5, 10 m 5m 2, 5, 10 m 5m 2, 5, 10 m 2, 5 m 2, 5, 10 m 2, 5, 10 m 2, 5 m 2, 5 m 2, 5 m 5m 5m 2, 5 m 5m 5m Cable Type PVC 2 x 0,34 PVC 2 x 0,34 PVC 3 x 0,34 PVC 3 x 0,25 PVC 2 x 0,34 PVC 3 x 0,34 PVC 2 x 0,34 PVC 3 x 0,34 PVC 2 x 0,34 PVC 3 x 0,14 PVC 3 x 0,34 PVC 3 x 0,25 PVC 3 x 0,34 PVC 3 x 0,34 PVC 3 x 0,25 PVC 2 x 0,34 Plug-in Cable Straight — — — M/P34614/5 — — — — — — — M/P34614/5 — — M/P34614/5 — 90° — — — M/P34615/5 — — — — — — — M/P34615/5 — — M/P34615/5 — Catalogue Page N 4.3.051 N 4.3.051 N 4.3.051 N 4.3.051 N 4.3.051 N 4.3.051 N 4.3.045 N 4.3.045 N 4.3.045 N 4.3.047 N 4.3.055 N 4.3.055 N 4.3.055 N 4.3.055 N 4.3.055 N 4.3.055 ** Insert cable length Full information on switches (technical data, polyurethane cable, dimensions etc.) please see catalogue pages Ordering Examples Cylinders To order a basic 25 mm bore cylinder with a 50 mm stroke quote: RM/8025/M/50 Mountings To order a front flange mounting style ‘G’ for 25 mm bore cylinder quote: M/P 19409 10/97 Switches To order a reed switch with LED and 2 m cable length quote: QM/34/2 Brackets for switches To order a bracket for magnetically operated switches QM/34; 25 mm bore cylinder quote: QM/33/025/22 Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. N 1.5.021.03 RM/8000/M Theoretical Forces ● Air Consumption ● Cushioning Cylinder ∅ 10 12 16 20 25 Theoretical forces (N) at 6 bar Outstroke Instroke 47,1 39,6 67,8 51 120 104 188 158 294 247 Air consumption (l/cm stroke) at 6 bar Outstroke Instroke 0,006 0,005 0,008 0,006 0,014 0,013 0,022 0,019 0,035 0,028 Model Cushion length (mm) — — 16 19 19 — — 8017 8021 8026 Initial volume (cm 3) — — 2,4 4,4 7,2 BASIC DIMENSIONS RM/8000/M — Standard Cylinders XC + stroke WF G EW- d13 AM L 12 PL PL EE VD EE L MR CD H9 BF KV 1 SW KV BE ø BA - 0,1 ø B - 0,1 KK BE ø MM h9 D SW 1 VA LB KW 1 KW Cylinder ∅ 10 12 16 20 25 AM 12 16 16 20 22 ∅B/BA -0,1 12 16 16 22 22 BE M12x1,25 M16x1,5 M16x1,5 M22x1,5 M22x1,5 BF 12 17 17 20 22 ∅ CD H9 4 6 6 8 8 ∅D 16,5 21 21 30 30 EE M5 M5 M5 G1/8 G1/8 EW -0,1 7,9 11,9 11,9 15,9 15,9 G 9 9,5 9,5 15 15 KK M4 M6 M6 M8 M10x1,25 KV (A/F) 19 22 22 27 27 KV1 (A/F) 7 10 10 13 17 KW 6 5 5 8 8 Cylinder ∅ 10 12 16 20 25 L 6 9 9 12 12 L12 — 3 3 3 4 LB 2 3 4 3 7 ∅ MM h 9 4 6 6 8 10 MR 8 8 7 11 9 PL 5,5 5,5 5,5 8 8 SW (A/F) — 5 5 7 9 SW1 (A/F) 14 19 19 27 27 WF 16 22 22 24 28 VA/VD 1,5 2 2 2 2 XC 64 75 82 95 104 at 0 mm 0,034 kg 0,058 kg 0,070 kg 0,145 kg 0,200 kg per 25 mm 0,007 kg 0,011 kg 0,012 kg 0,018 kg 0,028 kg KW1 2 3 3 4 5 CYLINDER VARIANTS RM/8000/MC — Cylinders (central rear port) RM/8000/MF — Cylinders (flat rear cover) ZJ + stroke EE Cylinder ∅ 10 12 16 20 25 ZJ + stroke EE EE M5 M5 M5 G 1/8 G 1/8 ZJ 62 72 78 92 97 EE at 0 mm 0,031 kg 0,052 kg 0,064 kg 0,130 kg 0,185 kg EE per 25 mm 0,007 kg 0,011 kg 0,012 kg 0,018 kg 0,028 kg RM/8017/M, RM/8021/M, RM/8026/M — Cylinders with Adjustable Cushioning Cushion screw Cylinder ∅ 16 20 25 at 0 mm 0,070 kg 0,145 kg 0,195 kg N 1.5.021.04 Cushion screws per 25 mm 0,012 kg 0,018 kg 0,028 kg Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. 10/97 RM/8000/M RM/8000/N2 — Cylinders with Non-rotating Piston Rod Cylinder ∅ 12 16 20 25 Section A SW2 (A/F) 5 5 6 8 Torque max. 0,04 Nm 0,04 Nm 0,15 Nm 0,25 Nm at 0 mm 0,058 kg 0,070 kg 0,145 kg 0,200 kg A-B per 25 mm 0,011 kg 0,012 kg 0,018 kg 0,028 kg B SW 2 RM/8000/JM — Cylinders with Double Ended Piston Rod ZM + 2 x stroke L 8 + stroke Cylinder ∅ 16 20 25 L8 56 68 69 ZM 100 116 125 at 0 mm 0,080 kg 0,165kg 0,250 kg per 25 mm 0,017 kg 0,028 kg 0,043 kg RM/8000/L4 — Cylinder with Locking Unit XC + stroke AB ø AE EE AH AK BE BE AL AJ ø AF AC AG BF WF AD SW SW 1 Cylinder ∅ 12 16 20 25 AB 21 21 24 24 AC 13 13 14 14 AD 47 47 62 64 ∅AE 8,5 8,5 9 9 ∅AF 20 20 22 22 AG 20 20 27 27 AH 20 20 38 38 AJ 4 4 4,5 4,5 AL 55,5 55,5 60 60 AK 10 10 19 19 Cylinder ∅ 12 16 20 25 BE M16x1,5 M16x1,5 M22x1,5 M22x1,5 BF 12 12 23 23 EE M5 M5 M5 M5 SW (A/F) 8 8 8 8 SW1 (A/F) 18,5 18,5 20,5 20,5 WF 17 17 27 29 XC 108 115 142,5 151,5 Locking Forces 180 N 180 N 350 N 350 N at 0 mm 0,130 kg 0,140 kg 0,300 kg 0,360 kg per 25 mm 0,011 kg 0,012 kg 0,018 kg 0,028 kg 10/97 Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. N 1.5.021.05 RM/8000/M MOUNTINGS M/P 19 . . . — Rear or Front Flange Mounting Style ‘B’ or ‘G’ ZF + stroke UR MF FB TF MF UF W AT AU AH M/P 19 . . . — Foot Mounting Style ‘C’ ø AB AO XS TR E XA + stroke Cylinder ∅ 10 12 16 20 25 ∅ AB 4,5 5,5 5,5 6,6 6,6 AH 16 20 20 25 25 AO 6 6 6 7,5 7,5 AT 2 3 3 4 4 AU 10 13 13 16 16 E 35 43 43 53 53 ∅ FB 4,5 5,5 5,5 6,6 6,6 MF 3 4 4 5 5 TF 30 40 40 50 50 Cylinder ∅ 10 12 16 20 25 TR 25 32 32 40 40 UF 40 51 51 63 63 UR 22 28 28 38 38 W 13 18 18 19 23 XA 54 62 68 80 85 XS 24 32 32 36 40 ZF 65 76 82 97 102 Style ‘B’, ‘G’ 0,020 kg 0,030 kg 0,030 kg 0,050 kg 0,050 kg Style ‘C’ 0,020 kg 0,030 kg 0,030 kg 0,060 kg 0,060 kg QM/8000/24 — Rear Hinge Mounting Style ‘L’ View A K1 K3 G1 XC + stroke H2 CA A G2 øS G4 K2 G3 Cylinder ∅ 10 12 16 20 25 CA 12 20 20 25 25 N 1.5.021.06 G1 6,5 18,5 18,5 20 20 G2 15 15 15 15 G3 15 30 30 35 35 G4 6 8 8 10 10 H2 1 1,5 1,5 2 2 K1 13,5 20 20 25 25 K2 10,5 15 15 20,5 20,5 Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. K3 2 3 3 3 3 ∅S 4,8 5,5 5,5 6,6 6,6 XC 64 75 82 95 104 Style ‘L’ 0,005 kg 0,020 kg 0,020 kg 0,040 kg 0,040 kg 10/97 RM/8000/M QM/8000/44 — Rear Hinge Mounting Style ‘L2’ View A K1 G1 XC + stroke H2 CA A G2 øS G4 K2 G3 Cylinder ∅ 10 12 16 20 25 CA 24 27 27 30 30 G1 11 13 13 16 16 G2 12,5 15 15 20 20 G3 20 25 25 32 32 G4 4 5 5 6 6 H2 2,5 3 3 4 4 K1 17,5 23 23 29,5 29,5 ∅S 4,5 5,5 5,5 6,6 6,6 K2 13 18 18 24 24 XC 64 75 82 95 104 Style ‘L2’ 0,018 kg 0,035 kg 0,035 kg 0,077 kg 0,077 kg QM/8000/38 — Piston Rod Swivel Mounting Style ‘AK’ SW 4 SW 1 4° KK KK 4° SW 3 SW 2 B1 F L2 L QM/8000/25 — Piston Rod Clevis Mounting Style ‘F’ (Corresponds to DIN ISO 8140) RK CM CL KK LE ø CK h 11 CL CE ER QM/8000/32 — Universal Piston Rod Eye Mounting Style ‘UF’ (Corresponds to DIN ISO 8139) EN - 0,1 CE 1 KK ZZ CN H 7 ER 1 LE 1 AX Cylinder ∅ 10 12 16 20 25 AX 14 14 14 16 25 B1 2 3 3 4 5 CE 16 24 24 32 40 CE1 27 30 30 36 42 ∅ CK h11 4 6 6 8 10 CL 8 12 12 16 20 CM 4 6 6 8 10 ∅ CN H7 5 6 6 8 10 EN -0,1 8 9 9 12 14 ER 6,5 9,5 9,5 13 16 ER1 8 9 9 11 14 F 12,5 14 14 18 26 KK M4 M6 M6 M8 M10x1,25 Cylinder ∅ 10 12 16 20 25 L 33 39 39 55 73 L2 8 12 12 16 20 LE 8 12 12 16 20 LE1 10 11 11 13 15 RK 11,5 17,5 17,5 22 28 SW1 (A/F) 11 7 7 10 19 SW2 (A/F) 3,2 5 5 7 12 SW3 (A/F) 7 10 10 13 17 SW4 (A/F) 11 13 13 17 30 Z 5° 5° 5° 5° 5° Style ‘AK’ 0,015 kg 0,024 kg 0,024 kg 0,054 kg 0,233 kg Style ‘F’ 0,010 kg 0,020 kg 0,020 kg 0,060 kg 0,100 kg Style ‘UF’ 0,020 kg 0,020 kg 0,020 kg 0,050 kg 0,080 kg 10/97 Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. N 1.5.021.07 RM/8000/M QM/8000/61 — Guide Blocks (guide rods run through roller bearings) EA + stroke FC EB EW FL EZ FM EC ø FS 2,5 +- 0,1 EP FV ED EJ ** ** FK FJ FH EM Notice adjustment range EC ET 2,5 +- 0,1 ø EY FO H7 EF ES ** FP Centering sleeve 2,5 ø FR f6 EG ø FO EZ FG H7 FA FE FB ø EX EV ER FW 2,5 +- 0,1 EL EM EK EO ø FD ø FF Safety zone ** ( 28 min) Cylinder ∅ 12 and 16 20 25 EA 132 160 160 EB 75 108 108 EC 32,5 32,5 32,5 ED 19 24 24 EF 37 58 58 EG 10 12 12 EJ 76 90 90 EK 63 76 76 EL 46 58 58 EM 24 38 38 Cylinder ∅ 12 and 16 20 25 EO 10 13 17 EP 8 13 13 ER 24 38 38 ES 65 75 75 ET 6,5 8,5 8,5 EV 4,6 5,7 5,7 EW 27 32 32 ∅ EX 8 10 10 ∅ EY 4,5 5,5 5,5 EZ M4 M5 M5 Cylinder ∅ 12 and 16 20 25 FA 5,5 6,5 6,5 FB 22 23 23 FC 30 34 34 ∅ FD 5,5 6,6 6,6 FE M4 M6 M6 FF 9 11 11 ∅ FG H7 6 9 9 FH 32 40 40 FJ 54 68 68 FK 65 79 79 Cylinder ∅ 12 and 16 20 25 FL 15 20 20 FM 10 14 14 ∅ FO H7 9 9 9 FP M5 M6 M6 ∅ FR f6 6 9 9 ∅ FS 8 10 10 FV M6 M8 M 10 x 1,25 FW 27 37 37 at 0 mm 0,40 kg 0,65 kg 0,65 kg per 100 mm 0,04 kg 0,06 kg 0,06 kg Note: Supplied complete with cylinder mounting screws and two centering sleeves. N 1.5.021.08 Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. 10/97 RM/8000/M Maximum Load for QM/8000/61 Center of gravity of load capacity f Centre of gravity Outstroke Outstroke Max. load capacity is dependent on the outstroke of a horizontally installed guide unit. In the case of short stroke operation, the load capacity figures taken from the diagram must be multiplied by the correction factor (diagram 2). In the curves of load capacity (diagram 1), the short stroke corrections have already been taken into account for a outstroke > 60 mm. The total deflection of guide rods will be determined by the addition of that due to own weight acc. to diagram 3 and that due to load capacity acc. to diagram 4. Max. load capacity depending on outstroke Deflection caused by own weight Deflection caused by a load of 10 N (diagram 1) (diagram 3) (diagram 4) (diagram 2) Load capacity (N) Correction factor Deflection ( mm ) f 100 1,0 2,5 80 0,9 2,0 60 0,8 1,5 1,5 0,7 1,0 1,0 0,6 0,5 0,5 40 Deflection ( mm ) f 8012-8016 8020-8025 8012-8016 2,5 8020-8025 2,0 8020-8025 20 8012-8016 0,5 0 0 100 200 300 400 500 600 Outstroke ( mm ) 0 20 0 40 60 0 0 100 200 300 400 500 600 0 100 200 300 400 500 600 Stroke ( mm ) Outstroke Outstroke ( mm ) ( mm ) Reduction of load capacity for short stroke operation In the case of shock load applications, the figures given in the diagrams above must be reduced by a factor of 2. Cylinder ∅ 10 12 16 20 25 BE M12x1,25 M16x1,5 M16x1,5 M22x1,5 M22x1,5 KV (A/F) 19 22 22 27 27 KW 6 5 5 8 8 Style ‘N’ 0,010 kg 0,009 kg 0,009 kg 0,017 kg 0,017 kg BE M/P 1 . . . — Nose Nut Style ‘N’ KW 10/97 Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. KV N 1.5.021.09 RM/8000/M QM/8000/34 – Head (Cap) Detachable Trunnion Mounting Style ‘FH’ XL + stroke XH TM ø TD +0,03 UW TL L1 Cylinder ∅ 12 16 20 25 L1 8 8 8 8 ∅ TD +0,03 6 6 6 6 TL 10 10 10 10 TM 38 38 46 46 UW 25 25 30 30 XH 18 18 20 24 XL — — 96 101 Style ‘FH’ 0,051 kg 0,051 kg 0,067 kg 0,067 kg SWITCH MOUNTING BRACKETS QM/33/000/23 – Brackets 10 Magnetically operated switch S < 15 mm stroke Switch mounting bracket T QM/33, QM/34, QM/134 (Ø 8 mm) Cylinder ∅ 10 12 16 20 25 S 27,5 28,5 29,5 29,5 31,5 T 19,5 21,5 23,5 26 28,5 Weight 0,007 kg 0,008 kg 0,008 kg 0,008 kg 0,007 kg QM/33/000/22 – Brackets QM/45/200/22 – Brackets B Magnetically operated switch ≥ 15 mm stroke Switch mounting bracket QM/33, QM/34, QM/134 (Ø 8 mm) Cylinder ∅ 10 12 16 20 25 B 8 8 10 10 10 N 1.5.021.010 R max. 16 18 20 22 24 R max. QM/45 (Ø 5 mm) Weight 0,003 kg 0,004 kg 0,006 kg 0,006 kg 0,007 kg Cylinder ∅ 10 12 16 20 25 B 8 8 10 10 10 Our policy is one of continued research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. R max. 14 15 18 20 22,5 Weight 0,002 kg 0,002 kg 0,005 kg 0,005 kg 0,006 kg 10/97