Illuminated beacons and indicator banks Characteristics References : pages 5/39 and 5/40 Characteristics Ambient air temperature With steady or flashing circuit : operation : - 25…+ 70 °C With discharge circuit : storage : operation : - 10…+ 50 °C Degree of protection IP 42 conforming to IEC 529 Rated insulation voltage Ui : 250 V Consumption With flashing circuit : (7 W bulb) - on c 24 V : 250 mA, - on c 230 V : 35 mA. With discharge circuit : (flashing lamp) - on a 24 V : 350 mA max. (switch-on : 720 mA), - on c 110/120 V : 100 mA, - on c 230 V : 80 mA. Audible elements : - a 12…48 V : 10…50 mA, - c 110…230 V : 3…7 mA. Bulb/lamp type Illuminated units with steady or flashing circuit : BA 15d base fitting bulbs, minimum power 5 W, maximum power 7 W. Illuminated units with high intensity “flash” lamp (integral xenon tube) : 13.6 cds with clear lens. Audible signalling unit 90 db at 1 m, continuous or intermittent. Fundamental frequency : 3 kHz Terminal referencing 1 terminal referenced “O” (–) common to all 5 possible stacked units, other terminals referenced 1 to 5, for use as required. Cabling Capacity : 2 x 2.5 mm2 max. Illuminated beacons and illuminated indicator banks are visual or audible signalling units used mainly to indicate machine operation sequences and to check status from a distance. They are visible through 360°. Example : start, stop machine, no material, call technical staff, fault indication, etc. i Illuminated beacon Pre-assembled with a single illuminating signalling unit : either steady, flashing or with high intensity xenon flash lamp : - optional accessory : anodised aluminium support tube ; 100 mm, 400 mm or 800 mm long, - optional accessory : support plate. i Illuminated indicator bank For assembly by the user, with up to 5 illuminated or 4 illuminated + 1 audible signalling units. It comprises : - a base, incorporating terminal block, cable clamp and support tube fixings, - 1 to 5 coloured lens units (green, red, orange, blue or clear) or 4 coloured lens units + 1 audible signalling units, - a top cover, where necessary, - optional accessory : anodised aluminium support tube ; 100 mm, 400 mm or 800 mm long, - optional accessory : support plate. The illuminated lens or audible signalling units stack vertically and are each locked by a single screw. Electrical connections between each unit are made automatically during assembly. 5 i Fixing Base fitted directly onto panel by means of 2 screws. Fixed onto panel using support plate (4 fixing screws) and 100 mm, 400 mm or 800 mm anodised aluminium tube. i Cabling Internal connections are brought out to a terminal block, with protected screw and captive cable clamp terminals, incorporated in the base unit. 5/38 Te Illuminated beacons and indicator banks Complete units References Characteristics : page 5/38 Illuminated beacons, direct or tube fixing Description Signal Colour Complete assembly comprising : 1 cover 1 coloured lens unit 1 base unit Steady light bulb not included (1) Green XVA-L33 0.200 Red XVA-L34 0.200 Orange XVA-L35 0.200 Blue XVA-L36 0.200 Clear XVA-L37 0.200 Green XVA-L43 0.200 Red XVA-L44 0.200 Orange XVA-L45 0.200 Blue XVA-L46 0.200 Clear XVA-L47 0.200 Green XVA-L63C024 0.210 Red XVA-L64C024 0.210 Orange XVA-L65C024 0.210 Blue XVA-L66C024 0.210 Clear XVA-L67C024 0.210 Green XVA-L63B120 0.210 Red XVA-L64B120 0.210 Orange XVA-L65B120 0.210 Blue XVA-L66B120 0.210 Clear XVA-L67B120 0.210 Green XVA-L63A220 0.210 Red XVA-L64A220 0.210 Orange XVA-L65A220 0.210 Blue XVA-L66A220 0.210 Clear XVA-L67A220 (1) Bulb type for use with direct supply : BA 15d base fitting incandescent, see page 5/41. 0.210 ≤ 230 V XVA-L3i Flashing light bulb not included (1) Reference Weight kg c 24…230 V (± 10 %) Discharge circuit for flashing light Integral high intensity xenon discharge tube XVA-L4i a 24 V Discharge circuit for flashing light Integral high intensity xenon discharge tube c 110/120 V 50/60 Hz Discharge circuit for flashing light Integral high intensity xenon discharge tube c 230 V (± 10 %) 50 Hz Illuminated beacons without xenon flashing light i , XVA-L4i i XVA-L3i with xenon flashing light iiiiii XVA-L6i Panel cut-out For direct fixing of illuminated beacons or indicator banks For tube fixing of illuminated beacons or indicator banks, using support plates 4xØ5 ou M5 (1) (1) 107 54 181 2xØ4 ou M4 42 54 = 42 Ø68 = = 42 Ø68 = (1) Ø 25 max. Te 5/39 5 Illuminated beacons and indicator banks Adaptable sub-assemblies References Characteristics : page 5/38 Illuminated indicator banks (up to 5 units), direct or tube fixing XVA-C34 Description Signal Colour Reference Illuminated lens units Not interchangeable with illuminated beacons Steady light bulb not included (1) Green Red Orange Blue Clear Yellow XVA-C33 XVA-C34 XVA-C35 XVA-C36 XVA-C37 XVA-C38 0.080 0.080 0.080 0.080 0.080 0.080 Green Red Orange Blue Clear XVA-C43 XVA-C44 XVA-C45 XVA-C46 XVA-C47 0.080 0.080 0.080 0.080 0.080 Green Red Orange Blue Clear XVA-C63C0241 XVA-C64C0241 XVA-C65C0241 XVA-C66C0241 XVA-C67C0241 0.090 0.090 0.090 0.090 0.090 Green Red Orange Blue Clear XVA-C63B120 XVA-C64B120 XVA-C65B120 XVA-C66B120 XVA-C67B120 0.090 0.090 0.090 0.090 0.090 Green Red Orange Blue Clear Supply voltage XVA-C63A220 XVA-C64A220 XVA-C65A220 XVA-C66A220 XVA-C67A220 Reference 0.090 0.090 0.090 0.090 0.090 Weight kg ≤ 230 V Flashing light bulb not included (1) XVA-C37 c 24 to 230 V (± 10 %) High intensity xenon flashing light With discharge circuit Integral tube (Maximum of 1 unit per indicator bank, mounted at top) a 24 V (2) With discharge circuit Integral tube XVA-C33 XVA-C35 c 110/120 V 50/60 Hz With discharge circuit Integral tube Description + Continuous a 12…48 V (2) XVA-C911 0.120 Intermittent a 12…48 V (2) XVA-C921 0.120 Continuous c 110…230 V XVA-C93 0.120 Intermittent c 110…230 V XVA-C94 0.120 Base unit + cover For bank without xenon flashing light XVA-C21 0.135 Base unit only For bank with xenon flashing light XVA-C07 0.120 Note : Illuminated indicator banks are supplied as sub-assemblies (for customer assembly). Each unit is packed individually and marked with its respective reference. Maximum number of units per bank : 5 illuminated units or 4 illuminated units + 1 audible unit (mounted at top). For accessories and spare parts see page 5/41. (1) Bulb type for use with direct supply : BA 15d base fitting incandescent, see page 5/41. (2) “–” line to common terminal (PLC solid state PNP type output). For “+” line to common terminal (NPN), please consult your Regional customer centre. Audible signalling unit (90 db at 1 m) XVA-C21 5 Illuminated indicator banks without xenon flashing light with xenon flashing light (2) b (2) (1) (1) 5/40 42 Ø68 Illuminated indicator banks without xenon flashing light Number of illuminated or b audible signalling units (2) 1 107 2 159 3 211 4 263 5 315 (1) XVA-C21 i , C4i i or C9i i (2) XVA-C3i b (3) (1) = c 230 V (± 10 %) 50 Hz Signal Weight kg = Te = 42 Ø68 = Illuminated indicator banks with xenon flashing light (3) Number of illuminated or b audible signalling units (2) 0 181 1 233 2 285 3 337 4 389 (1) XVA-C07 i , C4i i or C9i i (2) XVA-C3i iiiii (3) XVA-C6i Illuminated beacons and indicator banks References of accessories and spare parts Dimensions Characteristics : page 5/38 Accessories and spare parts Description Accessories for tube mounting XVA-C02 100 mm 400 mm 800 mm XVA-C02 XVA-C03 XVA-C04 0.030 0.120 0.240 Tube/support fixing plate Plastic Metal XVA-C01 XVA-C11 0.030 0.100 Side fixing bracket for tube/support fixing plate or base unit Metal XVA-C12 0.350 Sealing gaskets Dust and damp protecting For base unit XVA-C05 For tube support XVA-C06 0.004 0.005 Set of sealing gaskets For IP 54 degree of protection for beacons and indicator banks Bulbs, incandescent BA 15d base fitting (Sold in lots of 10) XVA-C12 Weight kg Tube only XVA-C01 XVA-C06 Unit reference 12 V - 5 W 24 V - 6.5 W 48 V - 6 W 120 V - 7 W 230 V - 7 W XVA-C082 0.100 DL1-BA012 DL1-BL024 DL1-BA048 DL1-BL120 DL1-BL230 0.010 0.010 0.010 0.010 0.010 i and support plate Tube XVA-C0i i 1 for illuminated beacons XVA-Ci and indicator banks 16 b (1) = 54 Ø68 = XVAC02 C03 b 63 363 (1) Tube Ø 25 mm 5 C04 763 Te 5/41