AD AD7612BSTZ

16-Bit, 750 kSPS, Unipolar/Bipolar
Programmable Input PulSAR® ADC
AD7612
FEATURES
APPLICATIONS
Process control
Medical instruments
High speed data acquisition
Digital signal processing
Instrumentation
Spectrum analysis
ATE
GENERAL DESCRIPTION
The AD7612 is a 16-bit charge redistribution successive
approximation register (SAR), architecture analog-to-digital
converter (ADC) fabricated on Analog Devices, Inc.’s iCMOS
high voltage process. The device is configured through hardware or
via a dedicated write only serial configuration port for input
range and operating mode. The AD7612 contains a high speed
16-bit sampling ADC, an internal conversion clock, an internal
reference (and buffer), error correction circuits, and both serial
and parallel system interface ports. A falling edge on CNVST
samples the analog input on IN+ with respect to a ground
sense, IN−. The AD7612 features four different analog input
ranges and three different sampling modes: warp mode for the
fastest throughput, normal mode for the fastest asynchronous
throughput, and impulse mode where power consumption is
scaled linearly with throughput. Operation is specified from
−40°C to +85°C.
FUNCTIONAL BLOCK DIAGRAM
TEMP REFBUFIN REF REFGND VCC VEE DVDD
AGND
AD7612
REF
AMP
AVDD
SERIAL
CONFIGURATION
16
PORT
PDBUF
IN+
SWITCHED
CAP DAC
IN–
OVDD
OGND
SERIAL DATA
PORT
REF
PDREF
DGND
D[15:0]
SER/PAR
BYTESWAP
CLOCK
CNVST
PARALLEL
INTERFACE
OB/2C
BUSY
PD
CONTROL LOGIC AND
CALIBRATION CIRCUITRY
RESET
RD
CS
06265-001
Multiple pins/software programmable input ranges:
5 V, 10 V, ±5 V, ±10 V
Pins or serial SPI®-compatible input ranges/mode selection
Throughput
750 kSPS (warp mode)
600 kSPS (normal mode)
500 kSPS (impulse mode)
INL: ±0.75 LSB typical, ±1.5 LSB maximum (±23 ppm of FSR)
16-bit resolution with no missing codes
SNR: 92 minimum (5 V) @ 2 kHz, 94 dB typical (±10 V) @ 2 kHz
THD: −107 dB typical
iCMOS™ process technology
5 V internal reference: typical drift 3 ppm/°C; TEMP output
No pipeline delay (SAR architecture)
Parallel (16- or 8-bit bus) and serial 5 V/3.3 V interface
SPI-/QSPI™-/MICROWIRE™-/DSP-compatible
Power dissipation: 190 mW @ 750 kSPS
Pb-free, 48-lead LQFP and LFCSP (7 mm × 7 mm) packages
WARP IMPULSE BIPOLAR TEN
Figure 1.
Table 1. 48-Lead 14-/16-/18-Bit PulSAR Selection
Type
Pseudo
Differential
100 kSPS to
250 kSPS
AD7651
AD7660
AD7661
True Bipolar
AD7663
500 kSPS to
570 kSPS
AD7650
AD7652
AD7664
AD7666
AD7665
800 kSPS to
1000 kSPS
AD7653
AD7667
True
Differential
AD7675
AD7676
AD7612
AD7671
AD7677
18-Bit, True
Differential
Multichannel/
Simultaneous
AD7678
AD7679
AD7674
>1000
kSPS
AD7621
AD7622
AD7623
AD7641
AD7643
AD7654
AD7655
PRODUCT HIGHLIGHTS
1.
Programmable input range and mode selection.
Pins or serial port for selecting input range/mode select.
2.
Fast throughput.
In warp mode, the AD7612 is 750 kSPS.
3.
Superior Linearity.
No missing 16-bit code. ±1.5 LSB max INL.
4.
Internal Reference.
5 V internal reference with a typical drift of ±3 ppm/°C
and an on-chip temperature sensor.
5.
Serial or Parallel Interface.
Versatile parallel (16- or 8-bit bus) or 2-wire serial interface
arrangement compatible with 3.3 V or 5 V logic.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
AD7612
TABLE OF CONTENTS
Features .............................................................................................. 1
Analog Inputs ............................................................................. 20
Applications....................................................................................... 1
Driver Amplifier Choice ........................................................... 21
General Description ......................................................................... 1
Voltage Reference Input/Output .............................................. 21
Functional Block Diagram .............................................................. 1
Power Supplies ............................................................................ 22
Product Highlights ........................................................................... 1
Conversion Control ................................................................... 23
Revision History ............................................................................... 2
Interfaces.......................................................................................... 24
Specifications..................................................................................... 3
Digital Interface.......................................................................... 24
Timing Specifications .................................................................. 5
Parallel Interface......................................................................... 24
Absolute Maximum Ratings............................................................ 7
Serial Interface ............................................................................ 25
ESD Caution.................................................................................. 7
Master Serial Interface............................................................... 25
Pin Configuration and Function Descriptions............................. 8
Slave Serial Interface .................................................................. 27
Typical Performance Characteristics ........................................... 12
Hardware Configuration ........................................................... 29
Terminology .................................................................................... 16
Software Configuration ............................................................. 29
Theory of Operation ...................................................................... 17
Microprocessor Interfacing....................................................... 30
Overview...................................................................................... 17
Application Information................................................................ 31
Converter Operation.................................................................. 17
Layout Guidelines....................................................................... 31
Modes of Operation ................................................................... 18
Evaluating Performance ............................................................ 31
Transfer Functions...................................................................... 18
Outline Dimensions ....................................................................... 32
Typical Connection Diagram ................................................... 19
Ordering Guide .......................................................................... 32
REVISION HISTORY
10/06—Revision 0: Initial Version
Rev. 0 | Page 2 of 32
AD7612
SPECIFICATIONS
AVDD = DVDD = 5 V; OVDD = 2.7 V to 5.5 V; VCC = 15 V; VEE = −15 V; VREF = 5 V; all specifications TMIN to TMAX, unless otherwise noted.
Table 2.
Parameter
RESOLUTION
ANALOG INPUT
Voltage Range, VIN
Analog Input CMRR
Input Current
Input Impedance
THROUGHPUT SPEED
Complete Cycle
Throughput Rate
Time Between Conversions
Complete Cycle
Throughput Rate
Complete Cycle
Throughput Rate
DC ACCURACY
Integral Linearity Error 3
No Missing Codes3
Differential Linearity Error3
Transition Noise
Zero Error (Unipolar or Bipolar)
Zero Error Temperature Drift
Bipolar Full-Scale Error
Unipolar Full-Scale Error
Full-Scale Error Temperature Drift
Power Supply Sensitivity
AC ACCURACY
Dynamic Range
Signal-to-Noise Ratio
Signal-to-(Noise + Distortion) (SINAD)
Total Harmonic Distortion
Spurious-Free Dynamic Range
–3 dB Input Bandwidth
Aperture Delay
Aperture Jitter
Transient Response
INTERNAL REFERENCE
Output Voltage
Temperature Drift
Line Regulation
Long-Term Drift
Turn-On Settling Time
Conditions/Comments
Min
16
VIN+ − VIN− = 0 V to 5 V
VIN+ − VIN− = 0V to 10 V
VIN+ − VIN− = ±5 V
VIN+ − VIN− = ±10 V
VIN− to AGND
fIN = 100 kHz
VIN = ±5 V, ±10 V @ 750 kSPS
See Analog Inputs section
−0.1
−0.1
−5.1
−10.1
−0.1
In warp mode
In warp mode
In warp mode
In normal mode
In normal mode
In impulse mode
In impulse mode
Typ
Max
Unit
Bits
+5.1
+10.1
+5.1
+10.1
+0.1
V
V
V
V
V
dB
μA
1.33
750 2
1
1.67
600
2
500
μs
kSPS
ms
μs
kSPS
μs
kSPS
+1.5
LSB 4
Bits
LSB
LSB
LSB
ppm/°C
LSB
LSB
ppm/°C
LSB
75
220 1
1
0
0
−1.5
16
−1
±0.75
+1.5
0.55
−35
+35
±1
−50
−70
+50
+70
±1
3
AVDD = 5 V ± 5%
VIN = 0 V to 5 V, fIN = 2 kHz, −60 dB
VIN = 0 V to 10 V, ±5 V, fIN = 2 kHz, −60 dB
VIN = ±10 V, fIN = 2 kHz, −60 dB
VIN = 0 V to 5 V, 0 V to 10 V, fIN = 2 kHz
VIN = ±5 V, ±10 V, fIN = 2 kHz
VIN = ±5 V, fIN = 2 kHz
VIN = 0 V to 10 V, ±5 V, fIN = 2 kHz
VIN = ±10 V, fIN = 2 kHz
fIN = 2 kHz
fIN = 2 kHz
VIN = 0 V to 5 V
Full-scale step
PDREF = PDBUF = low
REF @ 25°C
–40°C to +85°C
AVDD = 5 V ± 5%
1000 hours
CREF = 22 μF
Rev. 0 | Page 3 of 32
92.5
92
93.5
94
94.5
93
94
92.5
93
93.5
−107
107
45
2
5
500
4.965
5.000
±3
±15
50
10
5.035
dB 5
dB
dB
dB
dB
dB
dB
dB
dB
dB
MHz
ns
ps rms
ns
V
ppm/°C
ppm/V
ppm
ms
AD7612
Parameter
REFERENCE BUFFER
REFBUFIN Input Voltage Range
EXTERNAL REFERENCE
Voltage Range
Current Drain
TEMPERATURE PIN
Voltage Output
Temperature Sensitivity
Output Resistance
DIGITAL INPUTS
Logic Levels
VIL
VIH
IIL
IIH
DIGITAL OUTPUTS
Data Format
Pipeline Delay 6
VOL
VOH
POWER SUPPLIES
Specified Performance
AVDD
DVDD
OVDD
VCC
VEE
Operating Current 8 , 9
AVDD
With Internal Reference
With Internal Reference Disabled
DVDD
OVDD
VCC
VEE
Power Dissipation
With Internal Reference
With Internal Reference Disabled
In Power-Down Mode 10
TEMPERATURE RANGE 11
Specified Performance
Conditions/Comments
PDREF = high
PDREF = PDBUF = high
REF
750 kSPS throughput
Min
Typ
Max
Unit
2.4
2.5
2.6
V
4.75
5
250
AVDD + 0.1
V
μA
@ 25°C
311
1
4.33
−0.3
2.1
−1
−1
mV
mV/°C
kΩ
+0.6
OVDD + 0.3
+1
+1
V
V
μA
μA
0.4
V
V
5.25
5.25
5.25
15.75
0
V
V
V
V
V
Parallel or serial 16-bit
ISINK = 500 μA
ISOURCE = –500 μA
OVDD − 0.6
4.75 7
4.75
2.7
7
−15.75
5
5
15
−15
@ 750 kSPS throughput
19.5
18
6.5
0.5
3
2.3
2
VCC = 15 V, with internal reference buffer
VCC = 15 V
VEE = −15 V
@ 750 kSPS throughput
PDREF = PDBUF = low
PDREF = PDBUF = high
PD = high
TMIN to TMAX
205
190
10
−40
1
mA
mA
mA
mA
mA
mA
mA
230
210
mW
mW
μW
+85
°C
With VIN = 0 V to 5 V or 0 V to 10 V ranges, the input current is typically 70 μA. In all input ranges, the input current scales with throughput. See the Analog Inputs section.
All specified performance is guaranteed up to 750 kSPS throughout, however throughputs up to 900 kSPS can be used with some linearity performance degradation.
Linearity is tested using endpoints, not best fit. All linearity is tested with an external 5 V reference.
4
LSB means least significant bit. All specifications in LSB do not include the error contributed by the reference.
5
All specifications in decibels are referred to a full-scale range input, FSR. Tested with an input signal at 0.5 dB below full-scale, unless otherwise specified.
6
Conversion results are available immediately after completed conversion.
7
4.75 V or VREF – 0.1 V, whichever is larger.
8
Tested in parallel reading mode.
9
With internal reference, PDREF = PDBUF = low; with internal reference disabled, PDREF = PDBUF = high. With internal reference buffer, PDBUF = low.
10
With all digital inputs forced to OVDD.
11
Consult sales for extended temperature range.
2
3
Rev. 0 | Page 4 of 32
AD7612
TIMING SPECIFICATIONS
AVDD = DVDD = 5 V; OVDD = 2.7 V to 5.5 V; VCC = 15 V; VEE = −15 V; VREF = 5 V; all specifications TMIN to TMAX, unless otherwise noted.
Table 3.
Parameter
CONVERSION AND RESET (See Figure 33 and Figure 34)
Convert Pulse Width
Time Between Conversions
Warp Mode/Normal Mode/Impulse Mode1
CNVST Low to BUSY High Delay
BUSY High All Modes (Except Master Serial Read After Convert)
Warp Mode/Normal Mode/Impulse Mode
Aperture Delay
End of Conversion to BUSY Low Delay
Conversion Time
Warp Mode/Normal Mode/Impulse Mode
Acquisition Time
Warp Mode/Normal Mode/Impulse Mode
RESET Pulse Width
PARALLEL INTERFACE MODES (See Figure 35 and Figure 37)
CNVST Low to DATA Valid Delay
Warp Mode/Normal Mode/Impulse Mode
DATA Valid to BUSY Low Delay
Bus Access Request to DATA Valid
Bus Relinquish Time
MASTER SERIAL INTERFACE MODES2 (See Figure 39 and Figure 40)
CS Low to SYNC Valid Delay
CS Low to Internal SDCLK Valid Delay2
CS Low to SDOUT Delay
CNVST Low to SYNC Delay, Read During Convert
Warp Mode/Normal Mode/Impulse Mode
SYNC Asserted to SDCLK First Edge Delay
Internal SDCLK Period3
Internal SDCLK High3
Internal SDCLK Low3
SDOUT Valid Setup Time3
SDOUT Valid Hold Time3
SDCLK Last Edge to SYNC Delay3
CS High to SYNC HI-Z
CS High to Internal SDCLK HI-Z
CS High to SDOUT HI-Z
BUSY High in Master Serial Read After Convert3
CNVST Low to SYNC Delay, Read After Convert
Warp Mode/Normal Mode/Impulse Mode
SYNC Deasserted to BUSY Low Delay
Symbol
Min
t1
t2
10
Typ
Max
ns
1.33/1.67/2
t3
t4
t5
t6
t7
Unit
35
μs
ns
950/1250/1450
ns
ns
ns
950/1250/1450
ns
2
10
t8
t9
380
10
ns
ns
t10
910/1160/1410
t11
t12
t13
40
15
ns
ns
ns
ns
10
10
10
ns
ns
ns
20
2
t14
t15
t16
t17
65/315/560
t18
t19
t20
t21
t22
t23
t24
t25
t26
t27
t28
t29
t30
Rev. 0 | Page 5 of 32
3
30
15
10
4
5
5
45
10
10
10
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
See Table 4
830/1070/1310
25
ns
ns
AD7612
Parameter
SLAVE SERIAL/SERIAL CONFIGURATION INTERFACE MODES2 (See Figure 42,
Figure 43, and Figure 45)
External SDCLK, SCCLK Setup Time
External SDCLK Active Edge to SDOUT Delay
SDIN/SCIN Setup Time
SDIN/SCIN Hold Time
External SDCLK/SCCLK Period
External SDCLK/SCCLK High
External SDCLK/SCCLK Low
Symbol
Min
t31
t32
t33
t34
t35
t36
t37
5
2
5
5
25
10
10
Typ
Max
Unit
ns
ns
ns
ns
ns
ns
ns
18
1
In warp mode only, the time between conversions is 1 ms; otherwise, there is no required maximum time.
In serial interface modes, the SDSYNC, SDSCLK, and SDOUT timings are defined with a maximum load CL of 10 pF; otherwise, the load is 60 pF maximum.
3
In serial master read during convert mode. See Table 4 for serial master read after convert mode.
2
Table 4. Serial Clock Timings in Master Read After Convert Mode
DIVSCLK[1]
DIVSCLK[0]
SYNC to SDCLK First Edge Delay Minimum
Internal SDCLK Period Minimum
Internal SDCLK Period Maximum
Internal SDCLK High Minimum
Internal SDCLK Low Minimum
SDOUT Valid Setup Time Minimum
SDOUT Valid Hold Time Minimum
SDCLK Last Edge to SYNC Delay Minimum
BUSY High Width Maximum
Warp Mode
Normal Mode
Impulse Mode
1.6mA
0
0
3
30
45
15
10
4
5
5
0
1
20
60
90
30
25
20
8
7
1
0
20
120
180
60
55
20
35
35
1
1
20
240
360
120
115
20
90
90
Unit
ns
ns
ns
ns
ns
ns
ns
ns
1.65
1.9
2.15
2.35
2.6
2.85
3.75
4.00
4.25
6.53
6.78
7.03
μs
μs
μs
IOL
1.4V
2V
CL
60pF
0.8V
tDELAY
IOH
NOTES
1. IN SERIAL INTERFACE MODES, THE SYNC, SCLK, AND
SDOUT ARE DEFINED WITH A MAXIMUM LOAD
CL OF 10pF; OTHERWISE, THE LOAD IS 60pF MAXIMUM.
tDELAY
2V
0.8V
2V
0.8V
Figure 2. Load Circuit for Digital Interface Timing,
SDOUT, SYNC, and SCLK Outputs, CL = 10 pF
Figure 3. Voltage Reference Levels for Timing
Rev. 0 | Page 6 of 32
06265-003
500µA
06265-002
TO OUTPUT
PIN
Symbol
t18
t19
t19
t20
t21
t22
t23
t24
t28
AD7612
ABSOLUTE MAXIMUM RATINGS
Table 5.
Parameter
Analog Inputs/Outputs
IN+1, IN−1 to AGND
REF, REFBUFIN, TEMP,
REFGND to AGND
Ground Voltage Differences
AGND, DGND, OGND
Supply Voltages
AVDD, DVDD, OVDD
AVDD to DVDD, AVDD to OVDD
DVDD to OVDD
VCC to AGND, DGND
VEE to GND
Digital Inputs
PDREF, PDBUF2
Internal Power Dissipation3
Internal Power Dissipation4
Junction Temperature
Storage Temperature Range
Rating
VEE − 0.3 V to VCC + 0.3 V
AVDD + 0.3 V to
AGND − 0.3 V
±0.3 V
−0.3 V to +7 V
±7 V
±7 V
–0.3 V to +16.5
+0.3 V to −16.5
−0.3 V to OVDD + 0 .3 V
±20 mA
700 mW
2.5 W
125°C
−65°C to +125°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
1
See the Analog Inputs section.
See the Voltage Reference Input section.
Specification is for the device in free air: 48-Lead LFQP; θJA = 91°C/W,
θJC = 30°C/W.
4
Specification is for the device in free air: 48-Lead LFCSP; θJA = 26°C/W.
2
3
Rev. 0 | Page 7 of 32
AD7612
48 47 46 45 44 43 42
REF
IN–
REFGND
VCC
VEE
IN+
AGND
AVDD
TEMP
REFBUFIN
PDREF
PDBUF
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
41 40 39 38 37
AGND 1
36
BIPOLAR
35
CNVST
3
34
PD
BYTESWAP 4
33
RESET
32
CS
31
RD
30
TEN
SER/PAR 8
29
BUSY
9
28
D15/SCCS
D1 10
27
D14/SCCLK
D2/DIVSCLK[0] 11
26
D13/SCIN
D3/DIVSCLK[1] 12
25
D12/HW/SW
PIN 1
AVDD 2
AGND
OB/2C 5
AD7612
WARP 6
TOP VIEW
(Not to Scale)
IMPULSE 7
D0
06265-004
D11/RDERROR
D10/SYNC
D9/SDCLK
DGND
D8/SDOUT
DVDD
OVDD
OGND
D7/RDC/SDIN
D6/INVSCLK
D4/EXT/INT
D5/INVSYNC
13 14 15 16 17 18 19 20 21 22 23 24
Figure 4. Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
1, 3, 42
Mnemonic
AGND
Type1
P
2, 44
4
AVDD
BYTESWAP
P
DI
5
OB/2C
DI2
6
WARP
DI2
7
IMPULSE
DI2
8
SER/PAR
DI
9, 10
D[0:1]
DO
11, 12
D[2:3] or
DIVSCLK[0:1]
DI/O
Description
Analog Power Ground Pins. Ground reference point for all analog I/O. All analog I/O should be
referenced to AGND and should be connected to the analog ground plane of the system. In addition,
the AGND, DGND, and OGND voltages should be at the same potential.
Analog Power Pins. Nominally 4.75 V to 5.25 V and decoupled with 10 μF and 100 nF capacitors.
Parallel Mode Selection (8-Bit/16-Bit). When high, the LSB is output on D[15:8] and the MSB is output
on D[7:0]; when low, the LSB is output on D[7:0] and the MSB is output on D[15:8].
Straight Binary/Binary Twos Complement Output. When high, the digital output is straight binary.
When low, the MSB is inverted resulting in a twos complement output from its internal shift register.
Conversion Mode Selection. Used in conjunction with the IMPULSE input per the following:
Conversion Mode WARP
IMPULSE
Normal
Low
Low
Impulse
Low
High
Warp
High
Low
Normal
High
High
See the Modes of Operation section for a more detailed description.
Conversion Mode Selection. See the WARP pin description in the previous row of this table. See the
Modes of Operation section for a more detailed description.
Serial/Parallel Selection Input.
When SER/PAR = low, the parallel mode is selected.
When SER/PAR = high, the serial modes are selected. Some bits of the data bus are used as a serial port
and the remaining data bits are high impedance outputs.
Bit 0 and Bit 1 of the parallel port data output bus. These pins are always outputs regardless of the
state of SER/PAR.
In parallel mode, these outputs are used as Bit 2 and Bit 3 of the parallel port data output bus.
Serial Data Division Clock Selection. In serial master read after convert mode (SER/PAR = high, EXT/INT
= low, RDC/SDIN = low) these inputs can be used to slow down the internally generated serial data
clock that clocks the data output. In other serial modes, these pins are high impedance outputs.
Rev. 0 | Page 8 of 32
AD7612
Mnemonic
D4 or
EXT/INT
Type1
DI/O
14
D5 or
INVSYNC
DI/O
15
D6 or
INVSCLK
DI/O
16
D7 or
RDC or
DI/O
Pin No.
13
Description
In parallel mode, this output is used as Bit 4 of the parallel port data output bus.
Serial Data Clock Source Select. In serial mode, this input is used to select the internally generated
(master) or external (slave) serial data clock for the AD7612 output data.
When EXT/INT = low, master mode; the internal serial data clock is selected on SDCLK output.
When EXT/INT = high, slave mode; the output data is synchronized to an external clock signal (gated by CS)
connected to the SDCLK input.
In parallel mode, this output is used as Bit 5 of the parallel port data output bus.
Serial Data Invert Sync Select. In serial master mode (SER/PAR = high, EXT/INT = low). This input is used
to select the active state of the SYNC signal.
When INVSYNC = low, SYNC is active high.
When INVSYNC = high, SYNC is active low.
In parallel mode, this output is used as Bit 6 of the parallel port data output bus.
In all serial modes, invert SDCLK/SCCLK select. This input is used to invert both SDCLK and SCCLK.
When INVSCLK = low, the rising edge of SDCLK/SCCLK are used.
When INVSCLK = high, the falling edge of SDCLK/SCCLK are used.
In parallel mode, this output is used as Bit 7 of the parallel port data output bus.
Serial Data Read During Convert. In serial master mode (SER/PAR = high, EXT/INT = low) RDC is used to
select the read mode. Refer to the Master Serial Interface section.
When RDC = low, the current result is read after conversion. Note the maximum throughput is not
attainable in this mode.
When RDC = high, the previous conversion result is read during the current conversion.
SDIN
17
OGND
P
18
OVDD
P
19
DVDD
P
20
DGND
P
21
D8 or
SDOUT
DO
22
D9 or
SDCLK
DI/O
23
D10 or
SYNC
DO
Serial Data In. In serial slave mode (SER/PAR = high EXT/INT = high) SDIN can be used as a data input to
daisy-chain the conversion results from two or more ADCs onto a single SDOUT line. The digital data
level on SDIN is output on SDOUT with a delay of 16 SDCLK periods after the initiation of the read sequence.
Input/Output Interface Digital Power Ground. Ground reference point for digital outputs. Should be
connected to the system digital ground ideally at the same potential as AGND and DGND.
Input/Output Interface Digital Power. Nominally at the same supply as the supply of the host interface
2.5 V, 3 V, or 5 V and decoupled with 10 μF and 100 nF capacitors.
Digital Power. Nominally at 4.75 V to 5.25 V and decoupled with 10 μF and 100 nF capacitors. Can be
supplied from AVDD.
Digital Power Ground. Ground reference point for digital outputs. Should be connected to system
digital ground ideally at the same potential as AGND and OGND.
In parallel mode, this output is used as Bit 8 of the parallel port data output bus.
Serial Data output. In all serial modes this pin is used as the serial data output synchronized to SDCLK.
Conversion results are stored in an on-chip register. The AD7612 provides the conversion result, MSB
first, from its internal shift register. The data format is determined by the logic level of OB/2C.
When EXT/INT = low, (master mode) SDOUT is valid on both edges of SDCLK.
When EXT/INT = high, (slave mode).
When INVSCLK = low, SDOUT is updated on SDCLK rising edge.
When INVSCLK = high, SDOUT is updated on SDCLK falling edge.
In parallel mode, this output is used as Bit 9 of the parallel port data output bus.
Serial Data Clock. In all serial modes, this pin is used as the serial data clock input or output, dependent
on the logic state of the EXT/INT pin. The active edge where the data SDOUT is updated depends on
the logic state of the INVSCLK pin.
In parallel mode, this output is used as Bit 10 of the parallel port data output bus.
Serial Data Frame Synchronization. In serial master mode (SER/PAR = high, EXT/INT= low), this output
is used as a digital output frame synchronization for use with the internal data clock.
When a read sequence is initiated and INVSYNC = low, SYNC is driven high and remains high while the
SDOUT output is valid.
When a read sequence is initiated and INVSYNC = high, SYNC is driven low and remains low while the
SDOUT output is valid.
Rev. 0 | Page 9 of 32
AD7612
Pin No.
24
Mnemonic
D11 or
RDERROR
Type1
DO
25
D12 or
HW/SW
DI/O
26
D13 or
SCIN
DI/O
27
D14 or
SCCLK
DI/O
28
D15 or
SCCS
DI/O
29
BUSY
DO
30
TEN
DI2
31
32
RD
CS
DI
DI
33
RESET
DI
34
PD
DI2
35
CNVST
DI
36
37
BIPOLAR
REF
DI2
AI/O
38
39
40
41
REFGND
IN−
VCC
VEE
AI
AI
P
P
Description
In parallel mode, this output is used as Bit 11 of the parallel port data output bus.
Serial Data Read Error. In serial slave mode (SER/PAR = high, EXT/INT = high), this output is used as an
incomplete data read error flag. If a data read is started and not completed when the current
conversion is complete, the current data is lost and RDERROR is pulsed high.
In parallel mode, this output is used as Bit 12 of the parallel port data output bus.
Serial Configuration Hardware/Software Select. In serial mode, this input is used to configure
the AD7612 by hardware or software. See the Hardware Configuration section and Software
Configuration section.
When HW/SW = low, the AD7612 is configured through software using the serial configuration register.
When HW/SW = high, the AD7612 is configured through dedicated hardware input pins.
In parallel mode, this output is used as Bit 13 of the parallel port data output bus.
Serial Configuration Data Input. In serial software configuration mode (SER/PAR = high, HW/SW = low)
this input is used to serially write in, MSB first, the configuration data into the serial configuration
register. The data on this input is latched with SCCLK. See the Software Configuration section.
In parallel mode, this output is used as Bit 14 of the parallel port data output bus.
Serial Configuration Clock. In serial software configuration mode (SER/PAR = high, HW/SW = low) this
input is used to clock in the data on SCIN. The active edge where the data SCIN is updated depends on
the logic state of the INVSCLK pin. See the Software Configuration section.
In parallel mode, this output is used as Bit 15 of the parallel port data output bus.
Serial Configuration Chip Select. In serial software configuration mode (SER/PAR = high, HW/SW = low)
this input enables the serial configuration port. See the Software Configuration section.
Busy Output. Transitions high when a conversion is started, and remains high until the conversion
is complete and the data is latched into the on-chip shift register. The falling edge of BUSY can be
used as a data ready clock signal. Note that in master read after convert mode (SER/PAR = high,
EXT/INT = low, RDC = low) the busy time changes according to Table 4.
Input Range Select. Used in conjunction with BIPOLAR per the following:
Input Range BIPOLAR TEN
0 V to 5 V
Low
Low
0 V to 10 V
Low
High
±5 V
High
Low
±10 V
High
High
Read Data. When CS and RD are both low, the interface parallel or serial output bus is enabled.
Chip Select. When CS and RD are both low, the interface parallel or serial output bus is enabled. CS is
also used to gate the external clock in slave serial mode (not used for serial programmable port).
Reset Input. When high, reset the AD7612. Current conversion, if any, is aborted. The falling edge of
RESET resets the data outputs to all zero’s (with OB/2C = high) and clears the configuration register.
See the Digital Interface section. If not used, this pin can be tied to OGND.
Power-Down Input. When PD = high, power down the ADC. Power consumption is reduced and
conversions are inhibited after the current one is completed. The digital interface remains active
during power down.
Conversion Start. A falling edge on CNVST puts the internal sample-and-hold into the hold state and
initiates a conversion.
Input Range Select. See description for Pin 30.
Reference Input/Output.
When PDREF/PDBUF = low, the internal reference and buffer are enabled, producing 5 V on this pin.
When PDREF/PDBUF = high, the internal reference and buffer are disabled, allowing an externally
supplied voltage reference up to AVDD volts. Decoupling with at least a 22 μF is required with or
without the internal reference and buffer. See the Reference Decoupling section.
Reference Input Analog Ground. Connected to analog ground plane.
Analog Input Ground Sense. Should be connected to the analog ground plane or to a remote sense ground.
High Voltage Positive Supply. Normally +7 V to +15 V.
High Voltage Negative Supply. Normally 0 V to −15 V (0 V in unipolar ranges).
Rev. 0 | Page 10 of 32
AD7612
Pin No.
43
45
46
Mnemonic
IN+
TEMP
REFBUFIN
Type1
AI
AO
AI
47
PDREF
DI
48
PDBUF
DI
Description
Analog Input. Referenced to IN−.
Temperature Sensor Analog Output.
Reference Buffer Input. When using an external reference with the internal reference buffer (PDBUF =
low, PDREF = high), applying 2.5 V on this pin produces 5 V on the REF pin. See the Voltage Reference
Input section.
Internal Reference Power-Down Input.
When low, the internal reference is enabled.
When high, the internal reference is powered down, and an external reference must be used.
Internal Reference Buffer Power-Down Input.
When low, the buffer is enabled (must be low when using internal reference).
When high, the buffer is powered-down.
1
AI = analog input; AI/O = bidirectional analog; AO = analog output; DI = digital input; DI/O = bidirectional digital; DO = digital output; P = power.
In serial configuration mode (SER/PAR = high, HW/SW = low), this input is programmed with the serial configuration register and this pin is a don’t care. See the
Hardware Configuration section and Software Configuration section.
2
Rev. 0 | Page 11 of 32
AD7612
TYPICAL PERFORMANCE CHARACTERISTICS
AVDD = DVDD = 5 V; OVDD = 5 V; VCC = 15 V; VEE = −15 V; VREF = 5 V; TA = 25°C.
1.5
1.5
1.0
1.0
0.5
DNL (LSB)
INL (LSB)
0.5
0
0
–0.5
0
16384
32768
65536
49152
–1.0
06265-005
CODE
0
16384
Figure 5. Integral Nonlinearity vs. Code
65536
49152
Figure 8. Differential Nonlinearity vs. Code
180
180
NEGATIVE INL
POSITIVE INL
160
NEGATIVE DNL
POSITIVE DNL
160
140
NUMBER OF UNITS
140
120
100
80
60
120
100
80
60
40
40
20
20
0
–1.0
–0.8
–0.6
–0.4
–0.2
0
0.2
0.4
0.6
1.0
0.8
INL DISTRIBUTION (LSB)
0
–1.0
06265-006
NUMBER OF UNITS
32768
CODE
–0.8
–0.6
–0.4
Figure 6. Integral Nonlinearity Distribution (239 Devices)
140k
180k
0
0.2
0.4
0.6
1.0
0.8
Figure 9. Differential Nonlinearity Distribution (239 Devices)
200k
128400 130570
σ = 0.55
181942
–0.2
DNL DISTRIBUTION (LSB)
06265-009
–1.5
06265-008
–0.5
–1.0
σ = 0.52
120k
160k
100k
COUNTS
120k
100k
80k
31321
20k
20k
0
0
7FFE 7FFF
15
8000
93
8001
60k
40k
47749
40k
0
80k
8002
8003
8004
0
8005
0
8006
CODE IN HEX
Figure 7. Histogram of 261,120 Conversions of a DC Input
at the Code Center
0
0
0
0
1232
917
1
0
0
7FFE 7FFF 8000 8001 8002 8003 8004 8005 8006 8007
CODE IN HEX
Figure 10. Histogram of 261,120 Conversions of a DC Input
at the Code Transition
Rev. 0 | Page 12 of 32
06265-010
60k
06265-007
COUNTS
140k
AD7612
0
–20
SNR = 93.23dB
THD = –107.5dB
SFDR = 113.9dB
SINAD = 93.1dB
–40
±10V
±5V
0V TO +10V
0V TO +5V
SNR
SINAD
94.5
–60
SNR, SINAD (dB)
AMPLITUDE (dB of Full Scale)
95.0
fS = 750kSPS
fIN = 19.99kHz
–80
–100
–120
94.0
93.5
–140
375
250
FREQUENCY (kHz)
93.0
–60
–50
–40
–30
–20
0
–10
INPUT LEVEL (dB)
Figure 11. FFT 20 kHz
Figure 14. SNR and SINAD vs. Input Level (Referred to Full Scale)
96
–70
16.0
120
SNR
94
15.8
90
15.4
ENOB
15.2
88
86
15.0
84
14.8
82
14.6
1
14.4
100
10
100
90
–90
80
–100
FREQUENCY (kHz)
40
1
20
100
10
Figure 15. THD, Harmonics, and SFDR vs. Frequency
96
±10V
±5V
0V TO +10V
0V TO +5V
95
94
93
93
92
91
91
–35
–15
5
25
45
65
TEMPERATURE (°C)
85
105
125
06265-013
92
90
–55
–35
–15
5
25
45
65
85
TEMPERATURE (°C)
Figure 16. SINAD vs. Temperature
Figure 13. SNR vs. Temperature
Rev. 0 | Page 13 of 32
105
125
06265-016
SINAD (dB)
94
90
–55
30
FREQUENCY (kHz)
±10V
±5V
0V TO +10V
0V TO +5V
95
50
SECOND
HARMONIC
Figure 12. SNR, SINAD, and ENOB vs. Frequency
96
60
THIRD
HARMONIC
–110
–130
70
THD
–120
06265-012
80
THD, HARMONICS (dB)
15.6
110
SFDR
–80
ENOB (Bits)
92
SNR (dB)
SNR, SINAD (dB)
SINAD
SFDR (dB)
125
06265-015
0
06265-011
–180
06265-014
–160
AD7612
–96
124
±10V
±5V
0V TO +10V
0V TO +5V
–98
–100
120
–102
118
–104
–106
SFDR (dB)
THD (dB)
0V TO +10V
±5V
±10V
0V TO +5V
122
–108
–110
116
114
112
–112
–114
110
–116
–35
–15
5
25
45
65
85
105
125
TEMPERATURE (°C)
106
–55
06265-017
–120
–55
VREF (V)
NEGATIVE
FULL SCALE ERROR
–2
85
125
105
4.999
4.998
4.997
–3
–35
–15
5
25
45
65
85
105
125
TEMPERATURE (°C)
4.995
–55
Figure 18. Zero Error, Positive and Negative Full Scale vs. Temperature
60
–15
5
25
45
65
85
125
105
TEMPERATURE (°C)
Figure 21. Typical Reference Voltage Output vs. Temperature (3 Devices)
100000
10000
40
30
20
10
1000
100
10
1
AVDD, WARP/NORMAL
DVDD, ALL MODES
AVDD, IMPULSE
VCC +15V, VEE –15V,
ALL MODES
OVDD, ALL MODES
0.1
0
1
2
3
4
5
6
REFERENCE DRIFT (ppm/°C)
7
8
06265-019
0.01
Figure 19. Reference Voltage Temperature Coefficient Distribution (247 Devices)
Rev. 0 | Page 14 of 32
0.001
10
PDREF = PDBUF = HIGH
100
1000
10000
100000
SAMPLING RATE (SPS)
Figure 22. Operating Currents vs. Sample Rate
1000000
06265-022
OPERATING CURRENTS (µA)
50
0
–35
06265-021
4.996
–4
06265-018
ZERO ERROR, FULL SCALE ERROR (LSB)
65
5.000
ZERO
ERROR
–5
–55
NUMBER OF UNITS
45
5.001
POSITIVE
FULL SCALE ERROR
0
–1
25
5.002
4
1
5
Figure 20. SFDR vs. Temperature (Excludes Harmonics)
5
2
–15
TEMPERATURE (°C)
Figure 17. THD vs. Temperature
3
–35
06265-020
108
–118
AD7612
50
PD = PDBUF = PDREF = HIGH
OVDD = 2.7V @ 85°C
45
600
OVDD = 2.7V @ 25°C
40
500
400
t12 DELAY (ns)
35
VEE, –15V
VCC, +15V
DVDD
OVDD
AVDD
300
30
25
OVDD = 5V @ 85°C
20
OVDD = 5V @ 25°C
15
200
10
100
0
–35
–15
5
25
45
65
85
105
TEMPERATURE (°C)
Figure 23. Power-Down Operating Currents vs. Temperature
0
50
100
150
CL (pF)
Figure 24. Typical Delay vs. Load Capacitance CL
Rev. 0 | Page 15 of 32
200
06265-024
0
–55
5
06265-023
POWER-DOWN OPERATING CURRENTS (nA)
700
AD7612
TERMINOLOGY
Least Significant Bit (LSB)
The least significant bit, or LSB, is the smallest increment that
can be represented by a converter. For an analog-to-digital converter with N bits of resolution, the LSB expressed in volts is
LSB(V ) =
VINp-p
2N
Integral Nonlinearity Error (INL)
Linearity error refers to the deviation of each individual code
from a line drawn from negative full-scale through positive fullscale. The point used as negative full-scale occurs a ½ LSB before
the first code transition. Positive full-scale is defined as a level
1½ LSBs beyond the last code transition. The deviation is measured from the middle of each code to the true straight line.
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It
is often specified in terms of resolution for which no missing
codes are guaranteed.
Bipolar Zero Error
The difference between the ideal midscale input voltage (0 V)
and the actual voltage producing the midscale output code.
Unipolar Offset Error
The first transition should occur at a level ½ LSB above analog
ground. The unipolar offset error is the deviation of the actual
transition from that point.
Full-Scale Error
The last transition (from 111…10 to 111…11) should occur for
an analog voltage 1½ LSB below the nominal full-scale. The fullscale error is the deviation in LSB (or % of full-scale range) of
the actual level of the last transition from the ideal level and
includes the effect of the offset error. Closely related is the gain
error (also in LSB or % of full-scale range), which does not
include the effects of the offset error.
Dynamic Range
Dynamic range is the ratio of the rms value of the full-scale to
the rms noise measured for an input typically at −60 dB. The
value for dynamic range is expressed in decibels.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and
is expressed in decibels.
Signal-to-(Noise + Distortion) Ratio (SINAD)
SINAD is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
SINAD is expressed in decibels.
Spurious-Free Dynamic Range (SFDR)
The difference, in decibels (dB), between the rms amplitude of
the input signal and the peak spurious signal.
Effective Number of Bits (ENOB)
ENOB is a measurement of the resolution with a sine wave
input. It is related to SINAD and is expressed in bits by
ENOB = [(SINADdB − 1.76)/6.02]
Aperture Delay
Aperture delay is a measure of the acquisition performance
measured from the falling edge of the CNVST input to when
the input signal is held for a conversion.
Transient Response
The time required for the AD7612 to achieve its rated accuracy
after a full-scale step function is applied to its input.
Reference Voltage Temperature Coefficient
Reference voltage temperature coefficient is derived from the
typical shift of output voltage at 25°C on a sample of parts at the
maximum and minimum reference output voltage (VREF) measured at TMIN, T(25°C), and TMAX. It is expressed in ppm/°C as
TCVREF ( ppm/°C ) =
VREF ( Max ) – VREF ( Min)
VREF ( 25°C ) × ( TMAX – TMIN )
×106
where:
VREF (Max) = maximum VREF at TMIN, T(25°C), or TMAX.
VREF (Min) = minimum VREF at TMIN, T(25°C), or TMAX.
VREF (25°C) = VREF at 25°C.
TMAX = +85°C.
TMIN = –40°C.
Signal-to-Noise Ratio (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
Rev. 0 | Page 16 of 32
AD7612
THEORY OF OPERATION
IN+
REF
REFGND
LSB
MSB
32,768C 16,384C
4C
2C
C
SWA
SWITCHES
CONTROL
C
BUSY
COMP
OUTPUT
CODE
65,536C
SWB
CNVST
06265-025
IN–
CONTROL
LOGIC
Figure 25. ADC Simplified Schematic
OVERVIEW
CONVERTER OPERATION
The AD7612 is a very fast, low power, precise, 16-bit analog-todigital converter (ADC) using successive approximation capacitive
digital-to-analog (CDAC) architecture.
The AD7612 is a successive approximation ADC based on a
charge redistribution DAC. Figure 25 shows the simplified
schematic of the ADC. The CDAC consists of two identical
arrays of 16 binary weighted capacitors, which are connected
to the two comparator inputs.
The AD7612 can be configured at any time for one of four input
ranges and conversion mode with inputs in parallel and serial
hardware modes or by a dedicated write only, SPI-compatible
interface via a configuration register in serial software mode.
The AD7612 uses Analog Device’s patented iCMOS high voltage
process to accommodate 0 to 5 V, 0 to 10 V, ±5 V, and ±10 V
input ranges without the use of conventional thin films. Only
one acquisition cycle, t8, is required for the inputs to latch to the
correct configuration. Resetting or power cycling is not
required for reconfiguring the ADC.
The AD7612 features different modes to optimize performance
according to the applications. It is capable of converting 750,000
samples per second (750 kSPS) in warp mode, 600 kSPS in normal
mode, and 500 kSPS in impulse mode.
The AD7612 provides the user with an on-chip track-and-hold,
successive approximation ADC that does not exhibit any pipeline or latency, making it ideal for multiple multiplexed channel
applications.
For unipolar input ranges, the AD7612 typically requires three
supplies; VCC, AVDD (which can supply DVDD), and OVDD
which can be interfaced to either 5 V, 3.3 V, or 2.5 V digital logic.
For bipolar input ranges, the AD7612 requires the use of the
additional VEE supply.
During the acquisition phase, terminals of the array tied to the
comparator’s input are connected to AGND via SW+ and SW−.
All independent switches are connected to the analog inputs.
Thus, the capacitor arrays are used as sampling capacitors and
acquire the analog signal on IN+ and IN− inputs. A conversion
phase is initiated once the acquisition phase is complete and the
CNVST input goes low. When the conversion phase begins, SW+
and SW− are opened first. The two capacitor arrays are then
disconnected from the inputs and connected to the REFGND
input. Therefore, the differential voltage between the inputs
(IN+ and IN−) captured at the end of the acquisition phase is
applied to the comparator inputs, causing the comparator to
become unbalanced. By switching each element of the capacitor
array between REFGND and REF, the comparator input varies
by binary weighted voltage steps (VREF/2, VREF/4 through VREF/
65536). The control logic toggles these switches, starting with
the MSB first, in order to bring the comparator back into a
balanced condition.
After the completion of this process, the control logic generates
the ADC output code and brings the BUSY output low.
The device is housed in Pb-free, 48-lead LQFP or tiny LFCSP
7 mm × 7 mm packages that combine space savings with flexibility. In addition, the AD7612 can be configured as either a
parallel or serial SPI-compatible interface.
Rev. 0 | Page 17 of 32
AD7612
Impulse Mode
Warp Mode
Setting WARP = high and IMPULSE = low allow the fastest conversion rate up to 750 kSPS. However, in this mode, the full
specified accuracy is guaranteed only when the time between
conversions does not exceed 1 ms. If the time between two
consecutive conversions is longer than 1 ms (after power-up),
the first conversion result should be ignored since in warp mode,
the ADC performs a background calibration during the SAR
conversion process. This calibration can drift if the time between
conversions exceeds 1 ms thus causing the first conversion to
appear offset. This mode makes the AD7612 ideal for applications
where both high accuracy and fast sample rate are required. In
addition, the AD7612 can run up to 900 kSPS throughput with
some performance degradation, mainly dc linearity.
Setting WARP = low and IMPULSE = high uses the lowest power
dissipation mode and allows power saving between conversions.
The maximum throughput in this mode is 500 kSPS and in this
mode, the ADC powers down circuits after conversion making
the AD7612 ideal for battery-powered applications.
TRANSFER FUNCTIONS
Using the OB/2C digital input or via the configuration register,
the AD7612 offers two output codings: straight binary and twos
complement. See Figure 26 and Table 7 for the ideal transfer characteristic and digital output codes for the different analog input
ranges, VIN. Note that when using the configuration register, the
OB/2C input is a don’t care and should be tied to either high or low.
111...111
111...110
111...101
000...010
000...001
000...000
–FSR
Normal Mode
–FSR + 1 LSB
–FSR + 0.5 LSB
Setting WARP = IMPULSE = low or WARP = IMPULSE = high
allows the fastest mode (600 kSPS) without any limitation on
time between conversions. This mode makes the AD7612 ideal
for asynchronous applications such as data acquisition systems,
where both high accuracy and fast sample rate are required.
+FSR – 1 LSB
+FSR – 1.5 LSB
ANALOG INPUT
Figure 26. ADC Ideal Transfer Function
Table 7. Output Codes and Ideal Input Voltages
Description
FSR − 1 LSB
FSR − 2 LSB
Midscale + 1 LSB
Midscale
Midscale − 1 LSB
−FSR + 1 LSB
−FSR
1
2
VIN = 5 V
4.999924 V
4.999847 V
2.500076 V
2.5 V
2.499924 V
76.3 μV
0V
VIN = 10 V
9.999847 V
9.999695 V
5.000153 V
5.000000 V
4.999847 V
152.6 μV
0V
VREF = 5 V
VIN = ±5 V
+4.999847 V
+4.999695 V
+152.6 μV
0V
−152.6 μV
−4.999847 V
−5 V
VIN = ±10 V
+9.999695 V
+9.999390 V
+305.2 μV
0V
−305.2 μV
−9.999695 V
−10 V
This is also the code for overrange analog input (VIN+ − VIN− above VREF − VREFGND).
This is also the code for overrange analog input (VIN+ − VIN− below VREF − VREFGND).
Rev. 0 | Page 18 of 32
Digital Output Code
Straight Binary
Twos Complement
0xFFFF 1
0x7FFF1
0xFFFE
0x7FFE
0x8001
0x0001
0x8000
0x0000
0x7FFF
0xFFFF
0x0001
0x8001
0x0000 2
0x80002
06265-026
The AD7612 features three modes of operation: warp, normal,
and impulse. Each of these modes is more suitable to specific
applications. The mode is configured with the input pins, WARP
and IMPULSE, or via the configuration register. See Table 6 for
the pin details and the Hardware Configuration section and
Software Configuration section for programming the mode
selection with either pins or configuration register. Note that
when using the configuration register, the WARP and IMPULSE
inputs are don’t cares and should be tied to either high or low.
ADC CODE (Straight Binary)
MODES OF OPERATION
AD7612
TYPICAL CONNECTION DIAGRAM
Figure 27 shows a typical connection diagram for the AD7612 using the internal reference, serial data interface, and serial configuration
port. Different circuitry from that shown in Figure 27 is optional and is discussed in the following sections.
DIGITAL
SUPPLY (5V)
NOTE 5
ANALOG
SUPPLY (5V)
100nF
10µF
10µF
AVDD
+7V TO +15.75V
SUPPLY
10µF
100nF
10µF
100nF
AGND
100nF
DGND
10µF
100nF
DVDD
OVDD
VCC
DIGITAL
INTERFACE
SUPPLY
(2.5V, 3.3V, or 5V)
OGND
MICROCONVERTER/
MICROPROCESSOR/
DSP
BUSY
SDCLK
–7V TO –15.75V
SUPPLY
SCCLK
VEE
SERIAL
PORT 2
SCIN
NOTE 6
REF
CREF
22µF
NOTE 4
100nF
NOTE 3
SCCS
REFBUFIN
NOTE 7
AD7612
OB/2C
NOTE 2
SER/PAR
IN+
U1
D
CNVST
REFGND
OVDD
HW/SW
BIPOLAR
CC
2.7nF
TEN
WARP
ANALOG
INPUT–
IN–
NOTE 1
IMPULSE
NOTE 3
PDREF PDBUF
CLOCK
PD
RD
CS RESET
NOTES
1. SEE ANALOG INPUT SECTION. ANALOG INPUT(–) IS REFERENCED TO AGND ±0.1V.
2. THE AD8021 IS RECOMMENDED. SEE DRIVER AMPLIFIER CHOICE SECTION.
3. THE CONFIGURATION SHOWN IS USING THE INTERNAL REFERENCE. SEE VOLTAGE REFERENCE INPUT SECTION.
4. A 22µF CERAMIC CAPACITOR (X5R, 1206 SIZE) IS RECOMMENDED (FOR EXAMPLE, PANASONIC ECJ4YB1A226M).
SEE VOLTAGE REFERENCE INPUT SECTION.
5. OPTION, SEE POWER SUPPLY SECTION.
6. THE VCC AND VEE SUPPLIES SHOULD BE VCC = [VIN(MAX) +2V] and VEE = [VIN(MIN) –2V] FOR BIPOLAR INPUT RANGES.
FOR UNIPOLAR INPUT RANGES, VEE CAN BE 0V. SEE POWER SUPPLY SECTION.
7. OPTIONAL LOW JITTER CNVST, SEE CONVERSION CONTROL SECTION.
Figure 27. Typical Connection Diagram Shown with Serial Interface and Serial Programmable Port
Rev. 0 | Page 19 of 32
06265-027
ANALOG
INPUT +
SERIAL
PORT 1
SDOUT
AD7612
Input Range Selection
In parallel mode and serial hardware mode, the input range is
selected by using the BIPOLAR (bipolar) and TEN (10 Volt range)
inputs. See Table 6 for pin details and the Hardware Configuration
section and Software Configuration section for programming
the mode selection with either pins or configuration register. Note
that when using the configuration register, the BIPOLAR and
TEN inputs are don’t cares and should be tied to either high or low.
Input Structure
For instance, by using IN− to sense a remote signal ground,
ground potential differences between the sensor and the local
ADC ground are eliminated.
100
90
80
70
CMRR (dB)
ANALOG INPUTS
Figure 28 shows an equivalent circuit for the input structure of
the AD7612.
50
40
30
20
0 TO 5V
RANGE ONLY
0
1
D1
D3
D2
D4
RIN
10
100
1000
FREQUENCY (kHz)
CIN
IN+ OR IN–
10000
06265-029
10
AVDD
VCC
60
VEE
AGND
06265-028
Figure 29. Analog Input CMRR vs. Frequency
CPIN
Figure 28. AD7612 Simplified Analog Input
The four diodes, D1 to D4, provide ESD protection for the analog
inputs, IN+ and IN−. Care must be taken to ensure that the analog
input signal never exceeds the supply rails by more than 0.3 V,
because this causes the diodes to become forward-biased and to
start conducting current. These diodes can handle a forwardbiased current of 120 mA maximum. For instance, these conditions
could eventually occur when the input buffer’s U1 supplies are
different from AVDD, VCC, and VEE. In such a case, an input
buffer with a short-circuit current limitation can be used to protect
the part although most op amps’ short circuit current is <100 mA.
Note that D3 and D4 are only used in the 0 V to 5 V range to
allow for additional protection in applications that are switching
from the higher voltage ranges.
This analog input structure allows the sampling of the differential
signal between IN+ and IN−. By using this differential input,
small signals common to both inputs are rejected as shown in
Figure 29, which represents the typical CMRR over frequency.
During the acquisition phase for ac signals, the impedance of
the analog inputs, IN+ and IN−, can be modeled as a parallel
combination of Capacitor CPIN and the network formed by the
series connection of RIN and CIN. CPIN is primarily the pin capacitance. RIN is typically 70 Ω and is a lumped component comprised
of serial resistors and the on resistance of the switches. CIN is primarily the ADC sampling capacitor and depending on the input
range selected is typically 48 pF in the 0 V to 5 V range, typically
24 pF in the 0 V to 10 V and ±5 V ranges and typically 12 pF in
the ±10 V range. During the conversion phase, when the switches
are opened, the input impedance is limited to CPIN.
Since the input impedance of the AD7612 is very high, it can be
directly driven by a low impedance source without gain error. To
further improve the noise filtering achieved by the AD7612 analog
input circuit, an external, one-pole RC filter between the amplifier’s outputs and the ADC analog inputs can be used, as shown
in Figure 27. However, large source impedances significantly
affect the ac performance, especially total harmonic distortion
(THD). The maximum source impedance depends on the amount
of THD that can be tolerated. The THD degrades as a function
of the source impedance and the maximum input frequency.
Rev. 0 | Page 20 of 32
AD7612
DRIVER AMPLIFIER CHOICE
Although the AD7612 is easy to drive, the driver amplifier must
meet the following requirements:
•
•
For multichannel, multiplexed applications, the driver
amplifier and the AD7612 analog input circuit must be
able to settle for a full-scale step of the capacitor array at
a 16-bit level (0.0015%). For the amplifier, settling at 0.1%
to 0.01% is more commonly specified. This differs significantly from the settling time at a 16-bit level and should
be verified prior to driver selection. The AD8021 op amp
combines ultra-low noise and high gain bandwidth and
meets this settling time requirement even when used with
gains of up to 13.
The noise generated by the driver amplifier needs to be
kept as low as possible to preserve the SNR and transition
noise performance of the AD7612. The noise coming from
the driver is filtered by the external 1-pole low-pass filter
as shown in Figure 27. The SNR degradation due to the
amplifier is
SNRLOSS
⎛
⎞
⎜
⎟
VNADC
⎜
⎟
= 20 log ⎜
⎟
π
⎜⎜ VNADC 2 + f −3dB (NeN )2 ⎟⎟
2
⎝
⎠
The AD8021 meets these requirements and is appropriate for
almost all applications. The AD8021 needs a 10 pF external
compensation capacitor that should have good linearity as an
NPO ceramic or mica type. Moreover, the use of a noninverting
+1 gain arrangement is recommended and helps to obtain the
best signal-to-noise ratio.
The AD8022 can also be used when a dual version is needed
and a gain of 1 is present. The AD829 is an alternative in applications where high frequency (above 100 kHz) performance is not
required. In applications with a gain of 1, an 82 pF compensation
capacitor is required. The AD8610 is an option when low bias
current is needed in low frequency applications.
Since the AD7612 uses a large geometry, high voltage input
switch, the best linearity performance is obtained when using
the amplifier at its maximum full power bandwidth. Gaining
the amplifier to make use of the more dynamic range of the
ADC results in increased linearity errors. For applications
requiring more resolution, the use of an additional amplifier
with gain should precede a unity follower driving the AD7612.
See Table 8 for a list of recommended op amps.
Table 8. Recommended Driver Amplifiers
Amplifier
ADA4841-x
AD829
AD8021
AD8022
where:
VNADC is the noise of the ADC, which is:
VINp-p
AD8610/AD8620
2
VNADC = 2 SNR
10
20
f–3dB is the cutoff frequency of the input filter (3.9 MHz).
N is the noise factor of the amplifier (+1 in buffer
configuration).
eN is the equivalent input voltage noise density of the op
amp, in nV/√Hz.
•
The driver needs to have a THD performance suitable to
that of the AD7612. Figure 15 shows the THD vs. frequency
that the driver should exceed.
Typical Application
12 V supply, very low noise, low distortion,
low power, low frequency
±15 V supplies, very low noise, low frequency
±12 V supplies, very low noise, high frequency
±12 V supplies, very low noise, high
frequency, dual
±13 V supplies, low bias current, low
frequency, single/dual
VOLTAGE REFERENCE INPUT/OUTPUT
The AD7612 allows the choice of either a very low temperature
drift internal voltage reference, an external reference or an external
buffered reference.
The internal reference of the AD7612 provides excellent performance and can be used in almost all applications. However, the
linearity performance is guaranteed only with an external reference.
Rev. 0 | Page 21 of 32
AD7612
Temperature Sensor
To use the internal reference, the PDREF and PDBUF inputs
must be low. This enables the on-chip band gap reference, buffer,
and TEMP sensor resulting in a 5.00 V reference on the REF pin.
The internal reference is temperature-compensated to 5.000 V
±35 mV. The reference is trimmed to provide a typical drift of
3 ppm/°C. This typical drift characteristic is shown in Figure 19.
The TEMP pin measures the temperature of the AD7612. To
improve the calibration accuracy over the temperature range, the
output of the TEMP pin is applied to one of the inputs of the
analog switch (such as ADG779), and the ADC itself is used to
measure its own temperature. This configuration is shown
in Figure 30.
ADG779
External 2.5 V Reference and Internal Buffer (REF = 5 V)
(PDREF = High, PDBUF = Low)
To use an external reference with the internal buffer, PDREF
should be high and PDBUF should be low. This powers down
the internal reference and allows the 2.5 V reference to be applied
to REFBUFIN producing 5 V on the REF pin. The internal reference buffer is useful in multiconverter applications since a
buffer is typically required in these applications.
External 5 V Reference (PDREF = High, PDBUF = High)
To use an external reference directly on the REF pin, PDREF
and PDBUF should both be high. PDREF and PDBUF power
down the internal reference and the internal reference buffer,
respectively. For improved drift performance, an external reference such as the ADR445 or ADR435 is recommended.
Reference Decoupling
Whether using an internal or external reference, the AD7612
voltage reference input (REF) has a dynamic input impedance;
therefore, it should be driven by a low impedance source with
efficient decoupling between the REF and REFGND inputs. This
decoupling depends on the choice of the voltage reference, but
usually consists of a low ESR capacitor connected to REF and
REFGND with minimum parasitic inductance. A 22 μF (X5R,
1206 size) ceramic chip capacitor (or 47 μF tantalum capacitor)
is appropriate when using either the internal reference or the
ADR445/ADR435 external reference.
The placement of the reference decoupling is also important to
the performance of the AD7612. The decoupling capacitor should
be mounted on the same side as the ADC right at the REF pin
with a thick PCB trace. The REFGND should also connect to
the reference decoupling capacitor with the shortest distance
and to the analog ground plane with several vias.
For applications that use multiple AD7612 or other PulSAR
devices, it is more effective to use the internal reference buffer
to buffer the external 2.5 V reference voltage.
The voltage reference temperature coefficient (TC) directly impacts
full scale; therefore, in applications where full-scale accuracy
matters, care must be taken with the TC. For instance, a
±15 ppm/°C TC of the reference changes full-scale by ±1 LSB/°C.
TEMP
AD8021
TEMPERATURE
SENSOR
IN+
ANALOG INPUT
(UNIPOLAR)
CC
AD7612
06265-030
Internal Reference (REF = 5 V)
(PDREF = Low, PDBUF = Low)
Figure 30. Use of the Temperature Sensor
POWER SUPPLIES
The AD7612 uses five sets of power supply pins:
•
AVDD: analog 5 V core supply
•
VCC: analog high voltage positive supply
•
VEE: high voltage negative supply
•
DVDD: digital 5 V core supply
•
OVDD: digital input/output interface supply
Core Supplies
The AVDD and DVDD supply the AD7612 analog and digital
cores respectively. Sufficient decoupling of these supplies is
required consisting of at least a 10 μF capacitor and 100 nF on
each supply. The 100 nF capacitors should be placed as close as
possible to the AD7612. To reduce the number of supplies needed,
the DVDD can be supplied through a simple RC filter from the
analog supply, as shown in Figure 27.
High Voltage Supplies
The high voltage bipolar supplies, VCC and VEE are required
and must be at least 2 V larger than the maximum input, VIN.
For example, if using the bipolar 10 V range, the supplies should
be ±12 V minimum. Sufficient decoupling of these supplies is
also required consisting of at least a 10 μF capacitor and 100 nF
on each supply. For unipolar operation, the VEE supply can be
grounded with some slight THD performance degradation.
Digital Output Supply
The OVDD supplies the digital outputs and allows direct interface
with any logic working between 2.3 V and 5.25 V. OVDD should
be set to the same level as the system interface. Sufficient decoupling is required consisting of at least a 10 μF capacitor and 100 nF
with the 100 nF placed as close as possible to the AD7612.
Rev. 0 | Page 22 of 32
AD7612
Power Sequencing
Power Down
The AD7612 is independent of power supply sequencing and is
very insensitive to power supply variations on AVDD over a wide
frequency range as shown in Figure 31.
Setting PD = high powers down the AD7612, thus reducing
supply currents to their minimums as shown in Figure 23. When
the ADC is in power down, the current conversion (if any) is
completed and the digital bus remains active. To further reduce
the digital supply currents, drive the inputs to OVDD or OGND.
80
EXT REF
75
Power down can also be programmed with the configuration
register. See the Software Configuration section for details. Note
that when using the configuration register, the PD input is a
don’t care and should be tied to either high or low.
INT REF
70
60
55
CONVERSION CONTROL
50
45
40
30
1
10
100
1000
10000
FREQUENCY (kHz)
06265-031
35
The AD7612 is controlled by the CNVST input. A falling edge
on CNVST is all that is necessary to initiate a conversion. Detailed
timing diagrams of the conversion process are shown in Figure 33.
Once initiated, it cannot be restarted or aborted, even by the
power-down input, PD, until the conversion is complete. The
CNVST signal operates independently of CS and RD signals.
Figure 31. AVDD PSRR vs. Frequency
t2
t1
Power Dissipation vs. Throughput
CNVST
In impulse mode, the AD7612 automatically reduces its power
consumption at the end of each conversion phase. During the
acquisition phase, the operating currents are very low, which allows
a significant power savings when the conversion rate is reduced
(see Figure 32). This feature makes the AD7612 ideal for very
low power, battery-operated applications.
BUSY
PDREF = PDBUF = HIGH
10
1
10
ACQUIRE
CONVERT
t8
Figure 33. Basic Conversion Timing
Although CNVST is a digital signal, it should be designed with
special care with fast, clean edges, and levels with minimum
overshoot, undershoot, or ringing.
For applications where SNR is critical, the CNVST signal should
have very low jitter. This can be achieved by using a dedicated
oscillator for CNVST generation, or by clocking CNVST with a
high frequency, low jitter clock, as shown in Figure 27.
IMPULSE MODE POWER
1
CONVERT
The CNVST trace should be shielded with ground and a low value
(such as 50 Ω) serial resistor termination should be added close
to the output of the component that drives this line.
WARP MODE POWER
100
ACQUIRE
t7
100
SAMPLING RATE (kSPS)
1000
06265-032
POWER DISSIPATION (mW)
1000
t6
t5
MODE
It should be noted that the digital interface remains active even
during the acquisition phase. To reduce the operating digital supply
currents even further, drive the digital inputs close to the power
rails (that is, OVDD and OGND).
t4
t3
06265-033
PSRR (dB)
65
Figure 32. Power Dissipation vs. Sample Rate
Rev. 0 | Page 23 of 32
AD7612
INTERFACES
DIGITAL INTERFACE
CS = RD = 0
The AD7612 has a versatile digital interface that can be set up
as either a serial or a parallel interface with the host system. The
serial interface is multiplexed on the parallel data bus. The AD7612
digital interface also accommodates 2.5 V, 3.3 V, or 5 V logic. In
most applications, the OVDD supply pin is connected to the host
system interface 2.5 V to 5.25 V digital supply. Finally, by using
the OB/2C input pin, both twos complement or straight binary
coding can be used.
CNVST
Two signals, CS and RD, control the interface. When at least one of
these signals is high, the interface outputs are in high impedance.
Usually, CS allows the selection of each AD7612 in multi-circuit
applications and is held low in a single AD7612 design. RD is generally used to enable the conversion result on the data bus.
RESET
The RESET input is used to reset the AD7612. A rising edge on
RESET aborts the current conversion (if any) and tristates the
data bus. The falling edge of RESET resets the AD7612 and clears
the data bus and configuration register. See Figure 34 for the
RESET timing details.
t1
t10
BUSY
t4
t3
PREVIOUS CONVERSION DATA
06265-035
DATA
BUS
t11
NEW DATA
Figure 35. Master Parallel Data Timing for Reading (Continuous Read)
Slave Parallel Interface
In slave parallel reading mode, the data can be read either after
each conversion, which is during the next acquisition phase, or
during the following conversion, as shown in Figure 36 and
Figure 37, respectively. When the data is read during the conversion, it is recommended that it is read only during the first half
of the conversion phase. This avoids any potential feedthrough
between voltage transients on the digital interface and the most
critical analog conversion circuitry.
CS
t9
RESET
RD
BUSY
BUSY
DATA
BUS
CNVST
DATA
BUS
CURRENT
CONVERSION
t12
Figure 34. RESET Timing
06265-036
06265-034
t8
t13
Figure 36. Slave Parallel Data Timing for Reading (Read After Convert)
PARALLEL INTERFACE
The AD7612 is configured to use the parallel interface when
SER/PAR is held low.
CS = 0
t1
CNVST,
RD
Master Parallel Interface
BUSY
t4
t3
DATA
BUS
PREVIOUS
CONVERSION
t12
t13
Figure 37. Slave Parallel Data Timing for Reading (Read During Convert)
Rev. 0 | Page 24 of 32
06265-037
Data can be continuously read by tying CS and RD low, thus
requiring minimal microprocessor connections. However, in
this mode, the data bus is always driven and cannot be used in
shared bus applications (unless the device is held in RESET).
Figure 35 details the timing for this mode.
AD7612
8-Bit Interface (Master or Slave)
MASTER SERIAL INTERFACE
The BYTESWAP pin allows a glueless interface to an 8-bit bus.
As shown in Figure 38, when BYTESWAP is low, the LSB byte is
output on D[7:0] and the MSB is output on D[15:8]. When
BYTESWAP is high, the LSB and MSB bytes are swapped; the
LSB is output on D[15:8] and the MSB is output on D[7:0]. By
connecting BYTESWAP to an address line, the 16-bit data can
be read in two bytes on either D[15:8] or D[7:0]. This interface
can be used in both master and slave parallel reading modes.
The pins multiplexed on D[10:2] and used for master serial interface are DIVSCLK[0], DIVSCLK[1], EXT/INT, INVSYNC,
INVSCLK, RDC, SDOUT, SDCLK and SYNC.
CS
RD
Internal Clock (SER/PAR = high, EXT/INT = Low)
The AD7612 is configured to generate and provide the serial
data clock, SDCLK, when the EXT/INT pin is held low. The
AD7612 also generates a SYNC signal to indicate to the host
when the serial data is valid. The SDCLK, and the SYNC signals can be inverted, if desired using the INVSCLK and INVSYNC
inputs, respectively. Depending on the input, RDC, the data can
be read during the following conversion or after each conversion. Figure 39 and Figure 40 show detailed timing diagrams of
these two modes.
BYTESWAP
Read During Convert (RDC = High)
The AD7612 has a serial interface (SPI-compatible) multiplexed
on the data pins D[15:2]. The AD7612 is configured to use the
serial interface when SER/PAR is held high.
Setting RDC = high allows the master read (previous conversion
result) during conversion mode. Usually, because the AD7612 is
used with a fast throughput, this mode is the most recommended
serial mode. In this mode, the serial clock and data toggle at appropriate instances, minimizing potential feed through between digital
activity and critical conversion decisions. In this mode, the SDCLK
period changes since the LSBs require more time to settle and
the SDCLK is derived from the SAR conversion cycle. In this
mode, the AD7612 generates a discontinuous SDCLK of two
different periods and the host should use an SPI interface.
Data Interface
Read During Convert (RDC = Low, DIVSCLK[1:0] = [0 to 3])
The AD7612 outputs 16 bits of data, MSB first, on the SDOUT
pin. This data is synchronized with the 16 clock pulses provided
on the SDCLK pin. The output data is valid on both the rising
and falling edge of the data clock.
Setting RDC = low allows the read after conversion mode. Unlike
the other serial modes, the BUSY signal returns low after the 16
data bits are pulsed out and not at the end of the conversion phase,
resulting in a longer BUSY width (refer to Table 4 for BUSY timing
specifications). The DIVSCLK[1:0] inputs control the SDCLK
period and SDOUT data rate. As a result, the maximum throughput cannot be achieved in this mode. In this mode, the AD7612
also generates a discontinuous SDCLK however, a fixed period and
hosts supporting both SPI and serial ports can also be used.
HI-Z
HIGH BYTE
t12
PINS D[7:0]
HI-Z
LOW BYTE
LOW BYTE
t12
HI-Z
t13
HIGH BYTE
HI-Z
06265-038
PINS D[15:8]
Figure 38. 8-Bit and 16-Bit Parallel Interface
SERIAL INTERFACE
Serial Configuration Interface
The AD7612 can be configured through the serial configuration
register only in serial mode as the serial configuration pins are
also multiplexed on the data pins D[15:12]. Refer to the Hardware
Configuration section and Software Configuration section for
more information.
Rev. 0 | Page 25 of 32
AD7612
RDC/SDIN = 0
EXT/INT = 0
INVSCLK = INVSYNC = 0
CS, RD
t3
CNVST
t28
BUSY
t30
t29
t25
SYNC
t18
t19
t14
t20
1
2
D15
D14
SDCLK
t24
t21
3
14
15
D2
D1
t26
16
t15
t27
X
t16
D0
06265-039
SDOUT
t23
t22
Figure 39. Master Serial Data Timing for Reading (Read After Convert)
EXT/INT = 0
RDC/SDIN = 1
INVSCLK = INVSYNC = 0
CS, RD
t1
CNVST
t3
BUSY
t17
t25
SYNC
t19
t14
t20
SDCLK
t15
1
t21
t24
2
3
14
15
t18
t16
X
t22
t27
D15
D14
D2
D1
D0
06265-040
SDOUT
t26
16
t23
Figure 40. Master Serial Data Timing for Reading (Read Previous Conversion During Convert)
Rev. 0 | Page 26 of 32
AD7612
The pins multiplexed on D[11:4] used for slave serial
interface are: EXT/INT, INVSCLK, SDIN, SDOUT,
SDCLK and RDERROR.
External Clock (SER/PAR = High, EXT/INT = High)
Setting the EXT/INT = high allows the AD7612 to accept an
externally supplied serial data clock on the SDCLK pin. In this
mode, several methods can be used to read the data. The external serial clock is gated by CS. When CS and RD are both low,
the data can be read after each conversion or during the following
conversion. A clock can be either normally high or normally low
when inactive. For detailed timing diagrams, see Figure 42 and
Figure 43.
While the AD7612 is performing a bit decision, it is important
that voltage transients be avoided on digital input/output pins,
or degradation of the conversion result may occur. This is particularly important during the last 475 ns of the conversion phase
because the AD7612 provides error correction circuitry that can
correct for an improper bit decision made during the first part
of the conversion phase. For this reason, it is recommended that
any external clock provided, is a discontinuous clock that transitions only when BUSY is low, or, more importantly, that it does not
transition during the last 475 ns of BUSY high.
edge of SDCLK used to shift out the data on SDOUT (SDCLK
falling edge when INVSCLK = low). Therefore, the MSB of the
upstream converter follows the LSB of the downstream converter on the next SDCLK cycle. In this mode, the 40 MHz
SDCLK rate cannot be used since the SDIN to SDCLK setup
time, t33, is less than the minimum time specified. (SDCLK to
SDOUT delay, t32, is the same for all converters when simultaneously sampled). For proper operation, the SDCLK edge for
latching SDIN (or ½ period of SDCLK) needs to be:
t 1 / 2 SDCLK = t 32 + t 33
Or the max SDCLK frequency needs to be:
1
f SDCLK =
2(t 32 + t 33 )
If not using the daisy-chain feature, the SDIN input should be
tied either high or low.
BUSY
OUT
BUSY
BUSY
AD7612
AD7612
#2
(UPSTREAM)
#1
(DOWNSTREAM)
RDC/SDIN
CNVST
External Discontinuous Clock Data Read After
Conversion
Though the maximum throughput cannot be achieved using
this mode, it is the most recommended of the serial slave modes.
Figure 42 shows the detailed timing diagrams for this method.
After a conversion is complete, indicated by BUSY returning low,
the conversion result can be read while both CS and RD are low.
Data is shifted out MSB first with 16 clock pulses and, depending
on the SDCLK frequency, can be valid on the falling and rising
edges of the clock.
One advantage of this method is that conversion performance is
not degraded because there are no voltage transients on the digital
interface during the conversion process. Another advantage is
the ability to read the data at any speed up to 40 MHz, which
accommodates both the slow digital host interface and the fastest
serial reading.
Daisy-Chain Feature
Also in the read after convert mode, the AD7612 provides a daisychain feature for cascading multiple converters together using
the serial data input, SDIN, pin. This feature is useful for reduceing component count and wiring connections when desired, for
instance, in isolated multiconverter applications. See Figure 42
for the timing details.
SDOUT
RDC/SDIN
SDOUT
DATA
OUT
CNVST
CS
CS
SCLK
SCLK
SCLK IN
CS IN
CNVST IN
06265-041
SLAVE SERIAL INTERFACE
Figure 41. Two AD7612 Devices in a Daisy-Chain Configuration
External Clock Data Read During Previous Conversion
Figure 43 shows the detailed timing diagrams for this method.
During a conversion, while both CS and RD are low, the result
of the previous conversion can be read. Data is shifted out MSB
first with 16 clock pulses and, depending on the SDCLK frequency,
can be valid on the falling and rising edges of the clock. The
16 bits have to be read before the current conversion is complete;
otherwise, RDERROR is pulsed high and can be used to interrupt
the host interface to prevent incomplete data reading.
To reduce performance degradation due to digital activity, a fast
discontinuous clock of at least 40 MHz is recommended to ensure
that all the bits are read during the first half of the SAR
conversion phase.
The daisy-chain feature should not be used in this mode since
digital activity occurs during the second half of the SAR
conversion phase likely resulting in performance degradation.
An example of the concatenation of two devices is shown in
Figure 41. Simultaneous sampling is possible by using a common
CNVST signal. Note that the SDIN input is latched on the opposite
Rev. 0 | Page 27 of 32
AD7612
discontinuous SDCLK whenever possible to minimize potential
incorrect bit decisions. For the different modes, the use of a slower
SDCLK such as 20 MHz in warp mode, 15 MHz in normal mode
and 13 MHz in impulse mode can be used.
External Clock Data Read After/During Conversion
It is also possible to begin to read data after conversion and
continue to read the last bits after a new conversion has been
initiated. This method allows the full throughput and the use of
a slower SDCLK frequency. Again, it is recommended to use a
SER/PAR = 1
EXT/INT = 1
INVSCLK = 0
RD = 0
CS
BUSY
t31
SDCLK
t35
t31
X*
1
2
3
t32
t36
4
15
14
16
17
18
19
t37
SDOUT
D15
D14
D13
D2
D1
D0
X15
X14
X15
X14
X13
X2
X1
X0
Y15
Y14
t16
t33
t34
06265-042
SDIN
*A DISCONTINUOUS SDCLK IS RECOMMENDED.
Figure 42. Slave Serial Data Timing for Reading (Read After Convert)
EXT/INT = 1
SER/PAR = 1
INVSCLK = 0
RD = 0
CS
CNVST
BUSY
SDCLK
t35
t31
X*
1
2
3
t32
15
X*
16
X*
X*
X*
X*
t37
D15
SDOUT
t36
D14
D1
D0
DATA = SDIN
t27
t16
*A DISCONTINUOUS SDCLK IS RECOMMENDED.
Figure 43. Slave Serial Data Timing for Reading (Read Previous Conversion During Convert)
Rev. 0 | Page 28 of 32
06265-043
t31
AD7612
HARDWARE CONFIGURATION
The AD7612 can be configured at any time with the dedicated
hardware pins WARP, IMPULSE, BIPOLAR, TEN, OB/2C, and
PD for parallel mode (SER/PAR = low) or serial hardware mode
(SER/ PAR = high, HW/SW = high). Programming the AD7612
for mode selection and input range configuration can be done
before or during conversion. Like the RESET input, the ADC
requires at least one acquisition time to settle as indicated in
Figure 44. See Table 6 for pin descriptions. Note that these inputs
are high impedance when using the software configuration mode.
SOFTWARE CONFIGURATION
The pins multiplexed on D[15:12] used for software configuration are: HW/SW, SCIN, SCCLK, and SCCS. The AD7612 is
programmed using the dedicated write-only serial configurable
port (SCP) for conversion mode, input range selection, output
coding, and power-down using the serial configuration register.
See Table 9 for details of each bit in the configuration register.
The SCP can only be used in serial software mode selected with
SER/PAR = high and HW/SW = low since the port is multiplexed
on the parallel interface.
The SCP is accessed by asserting the port’s chip select, SCCS,
and then writing SCIN synchronized with SCCLK, which (like
SDCLK) is edge sensitive depending on the state of INVSCLK.
See Figure 45 for timing details. SCIN is clocked into the configuration register MSB first. The configuration register is an
internal shift register that begins with Bit 8, the start bit. The 9th
SPPCLK edge updates the register and allows the new settings to be
used. As indicated in the timing diagram, at least one acquisition
time is required from the 9th SCCLK edge. Bits [1:0] are reserved
bits and are not written to while the SCP is being updated.
The SCP can be written to at any time, up to 40 MHz, and it is
recommended to write to while the AD7612 is not busy converting, as detailed in Figure 45. In this mode, the full 750 kSPS is not
attainable because the time required for SCP access is (t31 + 8 × 1/
SCCLK +t8) minimum. If the full throughput is required, the
SCP can be written to during conversion, however it is not
HW/SW = 0
recommended to write to the SCP during the last 475 ns of conversion (BUSY = high) or performance degradation can result.
In addition, the SCP can be accessed in both serial master and
serial slave read during and read after convert modes.
Note that at power up, the configuration register is undefined.
The RESET input clears the configuration register (sets all bits
to 0), thus placing the configuration to 0 V to 5 V input, normal
mode, and twos complemented output.
Table 9. Configuration Register Description
Bit
8
Name
START
7
BIPOLAR
6
5
TEN
PD
4
IMPULSE
3
2
WARP
OB/2C
1
0
RSV
RSV
PD = 0
Description
START bit. With the SCP enabled (SCCS = low),
when START is high, the first rising edge of SCCLK
(INVSCLK = low) begins to load the register with
the new configuration.
Input Range Select. Used in conjunction with
Bit 6, TEN, per the following:
Input Range
BIPOLAR
TEN
0 V to 5 V
Low
Low
0 V to 10 V
Low
High
±5 V
High
Low
±10 V
Low
High
Input Range Select. See Bit 7, BIPOLAR.
Power Down.
PD = Low, normal operation.
PD = High, power down the ADC. The SCP is accessible while in power down. To power up the ADC,
write PD = low on the next configuration setting.
Mode Select. Used in conjunction with Bit 3,
WARP per the following:
Mode
WARP
IMPULSE
Normal
Low
Low
Impulse
Low
High
Warp
High
Low
Normal
High
High
Mode Select. See Bit 4, IMPULSE.
Output Coding
OB/2C = Low, use twos complement output.
OB/2C = High, use straight binary output.
Reserved.
Reserved.
SER/PAR = 0, 1
t8
t8
CNVST
BUSY
BIPOLAR,
TEN
06265-044
WARP,
IMPULSE
Figure 44. Hardware Configuration Timing
Rev. 0 | Page 29 of 32
AD7612
BIP = 0 OR 1
TEN = 0 OR 1
WARP = 0 OR 1
IMPULSE = 0 OR 1
SER/PAR = 1
HW/SW = 0
INVSCLK = 0
PD = 0
t8
CNVST
BUSY
t31
SCCS
t31
SCCLK
t35
1
2
3
4
t36
5
6
7
WARP
OB/2C
8
9
t37
t34
SCIN
X
START
BIPOLAR
TEN
PD
IMPULSE
X
06265-045
t33
Figure 45. Serial Configuration Port Timing
MICROPROCESSOR INTERFACING
The AD7612 is ideally suited for traditional dc measurement
applications supporting a microprocessor, and ac signal processing
applications interfacing to a digital signal processor. The AD7612
is designed to interface with a parallel 8-bit or 16-bit wide
interface, or with a general-purpose serial port or I/O ports on a
microcontroller. A variety of external buffers can be used with
the AD7612 to prevent digital noise from coupling into the ADC.
the DSP. The serial peripheral interface (SPI) on the ADSP-219x
is configured for master mode (MSTR) = 1, clock polarity bit
(CPOL) = 0, clock phase bit (CPHA) = 1, and SPI interrupt enable
(TIMOD) = 0 by writing to the SPI control register (SPICLTx).
It should be noted that to meet all timing requirements, the SPI
clock should be limited to 17 Mbps allowing it to read an ADC
result in less than 1 μs. When a higher sampling rate is desired,
use one of the parallel interface modes.
SPI Interface
DVDD
AD76121
ADSP-219x1
SER/PAR
BUSY
EXT/INT
CS
SDOUT
RD
SCLK
INVSCLK CNVST
1ADDITIONAL
PFx
SPIxSEL (PFx)
MISOx
SCKx
PFx OR TFSx
PINS OMITTED FOR CLARITY.
Figure 46. Interfacing the AD7612 to SPI Interface
The reading process can be initiated in response to the end-ofconversion signal (BUSY going low) using an interrupt line of
Rev. 0 | Page 30 of 32
06265-046
The AD7612 is compatible with SPI and QSPI digital hosts and
DSPs such as Blackfin® ADSP-BF53x and ADSP-218x/ADSP-219x.
Figure 46 shows an interface diagram between the AD7612 and
the SPI-equipped ADSP-219x. To accommodate the slower speed
of the DSP, the AD7612 acts as a slave device, and data must be
read after conversion. This mode also allows the daisy-chain
feature. The convert command could be initiated in response to
an internal timer interrupt.
AD7612
APPLICATION INFORMATION
LAYOUT GUIDELINES
While the AD7612 has very good immunity to noise on the
power supplies, exercise care with the grounding layout. To facilitate the use of ground planes that can be easily separated, design
the printed circuit board that houses the AD7612 so that the
analog and digital sections are separated and confined to certain
areas of the board. Digital and analog ground planes should be
joined in only one place, preferably underneath the AD7612, or
as close as possible to the AD7612. If the AD7612 is in a system
where multiple devices require analog-to-digital ground connections, the connections should still be made at one point only, a
star ground point, established as close as possible to the AD7612.
To prevent coupling noise onto the die, avoid radiating noise,
and to reduce feedthrough:
The DVDD supply of the AD7612 can be either a separate supply
or come from the analog supply, AVDD, or from the digital interface supply, OVDD. When the system digital supply is noisy, or
fast switching digital signals are present, and no separate supply is
available, it is recommended to connect the DVDD digital supply
to the analog supply AVDD through an RC filter, and to connect
the system supply to the interface digital supply OVDD and the
remaining digital circuitry. See Figure 27 for an example of this
configuration. When DVDD is powered from the system supply,
it is useful to insert a bead to further reduce high frequency spikes.
The AD7612 has four different ground pins: REFGND, AGND,
DGND, and OGND.
•
REFGND senses the reference voltage and, because it carries
pulsed currents, should be a low impedance return to the
reference.
• Do run the analog ground plane under the AD7612.
•
• Do shield fast switching signals, like CNVST or clocks, with
digital ground to avoid radiating noise to other sections of
the board, and never run them near analog signal paths.
AGND is the ground to which most internal ADC analog
signals are referenced; it must be connected with the least
resistance to the analog ground plane.
•
DGND must be tied to the analog or digital ground plane
depending on the configuration.
•
OGND is connected to the digital system ground.
• Do not run digital lines under the device.
• Avoid crossover of digital and analog signals.
• Run traces on different but close layers of the board, at right
angles to each other, to reduce the effect of feedthrough through
the board.
The power supply lines to the AD7612 should use as large a trace
as possible to provide low impedance paths and reduce the effect
of glitches on the power supply lines. Good decoupling is also
important to lower the impedance of the supplies presented to
the AD7612, and to reduce the magnitude of the supply spikes.
Decoupled ceramic capacitors, typically 100 nF, should be placed
on each of the power supplies pins, AVDD, DVDD, and OVDD,
VCC, and VEE. The capacitors should be placed close to, and
ideally right up against, these pins and their corresponding ground
pins. Additionally, low ESR 10 μF capacitors should be located
in the vicinity of the ADC to further reduce low frequency ripple.
The layout of the decoupling of the reference voltage is important.
To minimize parasitic inductances, place the decoupling capacitor
close to the ADC and connect it with short, thick traces.
EVALUATING PERFORMANCE
A recommended layout for the AD7612 is outlined in the EVALAD7612CB evaluation board documentation. The evaluation
board package includes a fully assembled and tested evaluation
board, documentation, and software for controlling the board
from a PC via the EVAL-CONTROL BRD3.
Rev. 0 | Page 31 of 32
AD7612
OUTLINE DIMENSIONS
0.75
0.60
0.45
9.20
9.00 SQ
8.80
1.60
MAX
37
48
36
1
PIN 1
0.15
0.05
7.20
7.00 SQ
6.80
TOP VIEW
1.45
1.40
1.35
(PINS DOWN)
0.20
0.09
7°
3.5°
0°
0.08
COPLANARITY
SEATING
PLANE
25
12
13
24
0.27
0.22
0.17
VIEW A
0.50
BSC
LEAD PITCH
051706-A
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BBC
Figure 47. 48-Lead Low Profile Quad Flat Package [LQFP]
(ST-48)
Dimensions shown in millimeters
7.00
BSC SQ
0.60 MAX
0.60 MAX
37
36
PIN 1
INDICATOR
TOP
VIEW
12° MAX
PIN 1
INDICATOR
48
5.25
5.10 SQ
4.95
(BOTTOM VIEW)
25
24
13
12
0.25 MIN
5.50
REF
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
0.50 BSC
SEATING
PLANE
1
EXPOSED
PAD
6.75
BSC SQ
0.50
0.40
0.30
1.00
0.85
0.80
0.30
0.23
0.18
0.20 REF
PADDLE CONNECTED TO VEE.
THIS CONNECTION IS NOT
REQUIRED TO MEET THE
ELECTRICAL PERFORMANCES.
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2
Figure 48. 48-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
7 mm × 7 mm Body, Very Thin Quad
(CP-48-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD7612BCPZ1
AD7612BCPZ-RL1
AD7612BSTZ1
AD7612BSTZ-RL1
EVAL-AD7612CB2
EVAL-CONTROL BRD33
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
48-Lead Lead Frame Chip Scale Package (LFCSP_VQ)
48-Lead Lead Frame Chip Scale Package (LFCSP_VQ)
48-Lead Low Profile Quad Flat Package (LQFP)
48-Lead Low Profile Quad Flat Package (LQFP)
Evaluation Board
Controller Board
1
Package Option
CP-48-1
CP-48-1
ST-48
ST-48
Z = Pb-free part.
This board can be used as a standalone evaluation board or in conjunction with the EVAL-CONTROL BRD3 for evaluation/demonstration purposes.
3
This board allows a PC to control and communicate with all Analog Devices. evaluation boards ending with the CB designators.
2
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06265-0-10/06(0)
Rev. 0 | Page 32 of 32