a Lithium-Ion Battery Charger ADP3820 FUNCTIONAL BLOCK DIAGRAM FEATURES ⴞ1% Total Accuracy 630 A Typical Quiescent Current Shutdown Current: 1 A (Typical) Stable with 10 F Load Capacitor 4.5 V to 15 V Input Operating Range Integrated Reverse Leakage Protection 6-Lead SOT-23-6 and 8-Lead SO-8 Packages Programmable Charge Current –20ⴗC to +85ⴗC Ambient Temperature Range Internal Gate-to-Source Protective Clamp + BIAS SD VIN – 50mV IS VREF GATE APPLICATIONS Li-Ion Battery Chargers Desktop Computers Hand-Held Instruments Cellular Telephones Battery Operated Devices VOUT ADP3820 GND GENERAL DESCRIPTION The ADP3820 is a precision single cell Li-Ion battery charge controller that can be used with an external Power PMOS device to form a two-chip, low cost, low dropout linear battery charger. It is available in two voltage options to accommodate Li-Ion batteries with coke or graphite anodes. The ADP3820’s high accuracy (± 1%) low shutdown current (1 µA) and easy charge current programming make this device especially attractive as a battery charge controller. Charge current can be set by an external resistor. For example, 50 mΩ of resistance can be used to set the charge current to 1 A. Additional features of this device include foldback current limit, overload recovery, and a gate-to-source voltage clamp to protect the external MOSFET. The proprietary circuit also minimizes the reverse leakage current from the battery if the input voltage of the charger is disconnected. This feature eliminates the need for an external serial blocking diode. RS 50mV VIN +5V C1 10mF R1 10kV NDP6020P IO = 1A VOUT + – Li-Ion BATTERY IS GATE VIN VOUT ADP3820-xx 22mF SD GND Figure 1. Li-Ion Charger Application Circuit The ADP3820 operates with a wide input voltage range from 4.5 V to 15 V. It is specified over the industrial temperature range of –20°C to +85°C and is available in the ultrasmall 6-lead surface mount SOT-23-6 and 8-lead SOIC packages. REV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 1999 ADP3820–SPECIFICATIONS1(V Parameter IN = [VOUT + 1 V] TA = –20ⴗC to +85ⴗC, unless otherwise noted) Conditions Symbol Min VIN VIN = VOUT + 1 V to 15 V VSD = 2 V VOUT VSD = 0 V VSD = 2 V IGND IGND INPUT VOLTAGE OUTPUT VOLTAGE ACCURACY QUIESCENT CURRENT Shutdown Mode Normal Mode Max Units 4.5 15 V –1 +1 % 1 630 15 800 µA µA 6 10 V GATE TO SOURCE CLAMP VOLTAGE 2 GATE DRIVE MINIMUM VOLTAGE Typ 0.7 GATE DRIVE CURRENT (SINK/SOURCE) V 1 mA ∆VGS GAIN ∆V OUT 80 dB CURRENT LIMIT THRESHOLD VOLTAGE VIN – VIS 40 75 mV LOAD REGULATION IOUT = 10 mA to 1 A, Circuit of Figure 1 –10 +10 mV VIN = VOUT + 1 V to 15 V IOUT = 0.1 A Circuit of Figure 1 (No Battery) –10 +10 mV 0.4 V V +15 µA 5 µA LINE REGULATION SD INPUT VOLTAGE VIH VIL VSD SD INPUT CURRENT VSD = 0 V to 5 V ISD OUTPUT REVERSE LEAKAGE CURRENT VIN = Floating IDISCH 2.0 –15 3 NOTES 1 All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC). 2 Provided gate-to-source clamp voltage is not exceeded. Specifications subject to change without notice. ORDERING GUIDE ABSOLUTE MAXIMUM RATINGS* Input Voltage, VIN ␣ . . . . . . . . . . . . . . . . . . . . . . . . . . . . ⴙ20 V Enable Input Voltage . . . . . . . . . . . . . . . 0.3 V to (VIN + 0.3 V) Operating Ambient Temperature Range . . . . –20°C to +85°C Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C θJA, SO-8 Package . . . . . . . . . . . . . . . . . . . . . . . . 150°C/W θJA, SOT-23-6 Package . . . . . . . . . . . . . . . . . . . . 230°C/W Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . +300°C Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . .+215°C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . .+220°C ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV Model Voltage Output Package Option* Marking Code ADP3820ART-4.1 ADP3820ART-4.2 ADP3820AR-4.1 ADP3820AR-4.2 4.1 V 4.2 V 4.1 V 4.2 V RT-6 (SOT-23-6) BAC RT-6 (SOT-23-6) BBC SO-8 SO-8 *SOT = Surface Mount Package. SO = Small Outline. Contact the factory for availability of other output voltage options. *This is a stress rating only; operation beyond these limits can cause the device to be permanently damaged. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADP3820 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. –2– WARNING! ESD SENSITIVE DEVICE REV. A ADP3820 PIN FUNCTION DESCRIPTIONS Pin Pin SOT-23-6 SO-8 Name Function 1 SD Shutdown. Pulling this pin low will disable the output. Device Ground. This pin should be tied to system ground closest to the load. Output Voltage Sense. This pin is connected to the MOSFET’s drain and directly to the load for optimal load regulation. Bypass to ground with a 10 µF or larger capacitor. Gate drive for the external MOSFET. Input Voltage. This is also the positive terminal connection of the current sense resistor. Current Sense. Used to sense the input current by monitoring the voltage across the current sense resistor. It is connected to the more negative terminal of the resistor as well as the power MOSFET’s source pin. IS pin should be tied to the VIN pin if the current limit feature is not used. No Connect. 2 8 7 GND 3 5 VOUT 4 3 GATE 5 4 VIN 6 1 IS 2, 6 NC REV. A PIN CONFIGURATIONS SO-8 IS 1 NC 2 ADP3820 RT-6 (SOT-23-6) 8 SD 7 GND TOP VIEW GATE 3 (Not to Scale) 6 NC VIN 4 5 NC = NO CONNECT –3– VOUT SD 1 GND 2 6 ADP3820 IS VIN TOP VIEW VOUT 3 (Not to Scale) 4 GATE 5 ADP3820 –Typical Performance Characteristics 4.110 0.760 VIN = 5.1V I LOAD = 10mA 4.105 0.720 IGND – mA OUTPUT VOLTAGE – V 0.740 4.100 0.700 0.680 0.660 4.095 0.640 4.090 0 200 400 600 ILOAD – mA 800 0.620 1000 5 7 4.110 15 0.900 I LOAD = 1A ILOAD = 1A 4.105 0.850 IGND – mA OUTPUT VOLTAGE – V 13 Figure 5. IGND vs. VIN (I LOAD = 10 mA)* Figure 2. V OUT vs. ILOAD (VIN = 5.1 V)* 4.100 4.095 4.090 9 11 INPUT VOLTAGE – V 0.800 0.750 5 7 9 11 13 0.700 15 5 7 INPUT VOLTAGE – V 9 11 INPUT VOLTAGE – V 13 15 Figure 6. IGND vs. VIN (I LOAD = 1 A)* Figure 3. VOUT vs. VIN (ILOAD = 1 A)* 1.200 4.110 VIN = 5.1V I LOAD = 10mA 4.105 1.000 IGND – mA OUTPUT VOLTAGE – V 1.100 4.100 0.900 0.800 0.700 4.095 0.600 4.090 5 7 9 11 13 0.500 0.001 15 0.1 10 1000 ILOAD – mA INPUT VOLTAGE – V Figure 4. VOUT vs. VIN (I LOAD = 10 mA)* Figure 7. I GND vs. ILOAD (VIN = 5.1 V)* *Reference Figure 1. –4– REV. A ADP3820 1.100 4.230 VIN = 5.1V I LOAD = 10mA 4.210 1.000 VOUT = 4.2V OUTPUT VOLTAGE – V 4.190 IGND – mA 0.900 0.800 0.700 4.170 4.150 4.130 VOUT = 4.1V 4.110 0.600 4.090 0.500 –40 0 –20 20 40 TEMPERATURE – 8C 60 4.070 –40 80 Figure 8. Quiescent Current vs. Temperature* –20 3.5 –30 3.0 PSRR – dB OUTPUT VOLTAGE – V 80 CLOAD = 10mF I LOAD = 1mA –10 4.0 2.5 2.0 1.5 –40 –50 –60 –70 1.0 –80 0.5 –90 –100 0 0 1 2 3 4 5 4 3 INPUT VOLTAGE – V 2 1 100 10 0 Figure 9. Power-Up/Power-Down* 1k 10k 100k FREQUENCY – Hz 1M 10M 120 140 Figure 12. Ripple Rejection* 5.000 7.0 VIN = 5.1V RS = 0.5V 5.5 4.000 OUTPUT VOLTAGE – V INPUT VOLTAGE – V 60 0 I LOAD = 10mA ILOAD = 10mA COUT = 10mF OUTPUT VOLTAGE – V 20 40 TEMPERATURE – 8C Figure 11. VOUT vs. Temperature, VIN = 5.1 V, ILOAD = 10 mA* 4.5 4.2 3.000 2.000 4.1 1.000 4.0 0.000 Figure 10. Line Transient Response (10 µ F Output Cap)* REV. A 0 –20 0 20 40 60 80 ILOAD – mA 100 Figure 13. Current Limit Foldback* –5– ADP3820 ADP3820. This k factor between VO of 0 V to about 2.5 V is: k ~ 0.65. APPLICATION INFORMATION The ADP3820 is very easy to use. A P-channel power MOSFET and a small capacitor on the output is all that is needed to form an inexpensive Li-Ion battery charger. The advantage of using the ADP3820 controller is that it can directly drive a PMOS FET to provide a regulated output current until the battery is charged. When the specified battery voltage is reached, the charge current is reduced and the ADP3820 maintains the maximum specified battery voltage accurately. θ JA = ∆T/(IO × k × VIN ) = 100/(1 × 0.65 × 5) = 30.7°C/W This thermal impedance can be realized using the transistor shown in Figure 1 when surface mounted to a 40 × 40 mm double-sided PCB with many vias around the tab of the surfacemounted FET to the backplane of the PCB. Alternatively, a TO-220 packaged FET mounted to a heatsink could be used. The θ or thermal impedance of a suitable heatsink is calculated below: When fully charged, the circuit in Figure 1 works like a well known linear regulator, holding the output voltage within the specified accuracy as needed by single cell Li-Ion batteries. The output is sensed by the VOUT pin. When charging a discharged battery, the circuit maintains a set charging current determined by the current sense resistor until the battery is fully charged, then reduces it to a trickle charge to keep the battery at the specified voltage. The voltage drop across the RS current sense resistor is sensed by the IS input of the ADP3820. At minimum battery voltage or at shorted battery, the circuit reduces this current (foldback) to limit the dissipation of the FET (see Figure 13). Both the VIN input and VOUT sense pins of the IC need to be bypassed by a suitable bypass capacitor. θ < (θ JA – θJC) = 30.7 – 2 = +28.7°C/W Where the θ JC, or junction-to-case thermal impedance of the FET can be read from the FET data sheet. A low cost such heatsink is type PF430 made by Thermalloy, with a θ = +25.3°C/W. The current sense resistor for this application can be simply calculated: R S = VS /IO = 0.05/1 = 50 mΩ Where VS is specified on the data sheet as current limit threshold voltage at 40 mV–75 mV. For battery charging applications, it is adequate to use the typical 50 mV midvalue. A 6 V gate-to-source voltage clamp is provided by the ADP3820 to protect the MOSFET gates at higher source voltages. The ADP3820 also has a TTL SD input, which may be connected to the input voltage to enable the IC. Pulling it to low or to ground will disable the FET-drive. B. Nonpreregulated Input Voltage If the input voltage source is, for example, a rectified and capacitor-filtered secondary voltage of a small wall plug-in transformer, the heatsinking requirement is more demanding. The VINMIN should be specified 5 V, but at the lowest line voltage and full load current. The required thermal impedance can be calculated the same way as above, but here we have to use the maximum output rectified voltage, which can be substantially higher than 5 V, depending on transformer regulation and line voltage variation. For example, if VINMAX is 10 V Design Approach Due to the lower efficiency of Linear Regulator Charging, the most important factor is the thermal design and cost, which is the direct function of the input voltage, output current and thermal impedance between the MOSFET and the ambient cooling air. The worse-case situation is when the battery is shorted since the MOSFET has to dissipate the maximum power. θJA = ∆T/(IO × k × VINMAX) = 100/(1 × 0.65 × 10) = +15.3°C/W A tradeoff must be made between the charge current, cost and thermal requirements of the charger. Higher current requires a larger FET with more effective heat dissipation leading to a more expensive design. Lowering the charge current reduces cost by lowering the size of the FET, possibly allowing a smaller package such as SOT-23-6. The following designs consider both options. Furthermore, each design is evaluated under two input source voltage conditions. The θ suitable heatsink thermal impedance: θ < θJA – θJC = 15.3 – 2 = 13.3°C/W A low cost heatsink is Type 6030B made by Thermalloy, with a θ = +12.5°C/W. Lower Current Option A. Preregulated Input Voltage (5 V ⴞ 10%) If lower charging current is allowed, the θJA value can be increased, and the system cost decreased. The lower cost is assured by using an inexpensive MOSFET with, for example, a NDT452P in a SOT-23-6 package mounted on a small 40 × 40 mm area on double-sided PCB. This provides a convection cooled thermal impedance of θ JA = +55°C/W, presuming many vias are used around the FET to the backplane. Allowing a maximum FET junction temperature of +150°C, at +50°C ambient, and at convection cooling the maximum allowed heat rise is thus 150°C–50°C = 100°C. Regarding input voltage, there are two options: A. The input voltage is preregulated, e.g., 5 V ± 10% B. The input voltage is not a preregulated source, e.g., a wall plug-in transformer with a rectifier and capacitive filter. Higher Current Option A. Preregulated Input Voltage (5 V ⴞ 10%) For the circuit shown in Figure 1, the required θJA thermal impedance can be calculated as follows: if the FET data sheet allows a max FET junction temperature of TJMAX = 150°C, then at 50°C ambient and at convection cooling, the maximum allowed ∆T junction temperature rise is thus, TJMAX – TAMAX = 150°C – 50°C = 100°C. The maximum foldback current allowed: IFB = ∆T/(θ × VIN ) = 100/(55 × 5) = 0.33 A Thus the full charging current: The maximum current for a shorted or discharged battery is reduced from the set charge current by a multiplier factor shown in Figure 13 due to the foldback current limiting feature of the IOUTMAX = IFB/k = 0.5 A k is calculated in the above example. –6– REV. A ADP3820 The current sense resistor for this application: Gate-to-Source Clamp A 6 V gate-to-source voltage clamp is provided by the ADP3820 to protect most MOSFET gates in the event the VIN > VGS allowed and the output is suddenly shorted to ground. This allows use of the new, low RDS(ON) MOSFETs. R S = VS/IO = 0.05/0.5 = 100 mΩ FET Selection The type and size of the pass transistor are determined by the threshold voltage, input-output voltage differential and load current. The selected PMOS must satisfy the physical and thermal design requirements. To ensure that the maximum VGS provided by the controller will turn on the FET at worst case conditions, (i.e., temperature and manufacturing tolerances) the maximum available VGS must be determined. Maximum VGS is calculated as follows: Short Circuit Protection The power FET is protected during short circuit conditions with a foldback type of current limiting that significantly reduces the current. See Figure 13 for foldback current limit information. Current Sense Resistor Current limit is achieved by setting an appropriate current sense resistor (RS) across the current limit threshold voltage. Current limit sense resistor, RS, is calculated as shown above. Proper derating is advised to select the power dissipation rating of the resistor. VGS = VIN – VBE – IOUTMAX × RS where IOUTMAX = Maximum Output Current = Current Sense Resistor RS ~ 0.7 V (Room Temperature) VBE ~ 0.5 V (Hot) ~ 0.9 V (Cold) The simplest and cheapest sense resistor for high current applications, (i.e., Figure 1) is a PCB trace. However, the temperature dependence of the copper trace and the thickness tolerances of the trace must be considered in the design. The resistivity of copper has a positive temperature coefficient of +0.39%/°C. Copper’s Tempco, in conjunction with the proportional-toabsolute temperature (± 0.3%) current limit voltage, can provide an accurate current limit. Table I provides the typical resistance values for PCB copper traces. Alternately, an appropriate sense resistor, such as surface mount sense resistors, available from KRL, can be used. For example: VIN = 5 V, and IOUTMAX = 1 A, VGS = 5 V – 0.7 V – 1 A × 50 mΩ = 4.25 V If VGS < 5 V, logic level FET should be considered. If VGS > 5 V, either logic level or standard MOSFET can be used. The difference between VIN and VO (VDS) must exceed the voltage drop due to the sense resistor plus the ON-resistance of the FET at the maximum charge current. The selected MOSFET must satisfy these criteria; otherwise, a different pass device should be used. Table I. Printed Circuit Copper Resistance Conductor Thickness VDS = VIN – VO = 5 V – 4.2 V = 0.8 V 1/2oz/ft2 (18 µm) The maximum RDS(ON) required at the available gate drive (VDR) and Drain-to-Source voltage (VDS) is: RDS(ON) = VDS/IOUTMAX From the Drain-to Source current vs. Drain-to-Source voltage vs. gate drive graph off the MOSFET data sheet, it can be determined if the above calculated RDS(ON) is higher than the graph indicates. However, the value read from the MOSFET data sheet graph must be adjusted based on the junction temperature of the MOSFET. This adjustment factor can be obtained from the normalized RDS(ON) vs. junction temperature graph in the MOSFET data sheet. 1oz/ft2 (35 µm) 2oz/ft2 (70 µm) External Capacitors The ADP3820 is stable with or without a battery load, and virtually any good quality output filter capacitors can be used (anyCAP™), independent of the capacitor’s minimum ESR (Effective Series Resistance) value. The actual value of the capacitor and its associated ESR depends on the gm and capacitance of the external PMOS device. A 10 µF tantalum or aluminum electrolytic capacitor at the output is sufficient to ensure stability for up to a 10 A output current. 3oz/ft2 (106 µm) Shutdown Mode Applying a TTL high signal to the SD pin or tying it to the input pin will enable the output. Pulling this pin low or tying it to ground will disable the output. In shutdown mode, the controller’s quiescent current is reduced to less than 1 µA. anyCAP is a trademark of Analog Devices, Inc. REV. A –7– Conductor Width/Inch Resistance m⍀/In 0.025 0.050 0.100 0.200 0.500 39.3 19.7 9.83 4.91 1.97 0.025 0.050 0.100 0.200 0.500 19.7 9.83 4.91 2.46 0.98 0.025 0.050 0.100 0.200 0.500 9.83 4.91 2.46 1.23 0.49 0.025 0.050 0.100 0.200 0.500 6.5 3.25 1.63 0.81 0.325 ADP3820 For optimum voltage regulation, place the load as close as possible to the device’s VOUT and GND pins. It is recommended to use dedicated PCB traces to connect the MOSFET’s drain to the positive terminal and GND to the negative terminal of the load to avoid voltage drops along the high current carrying PCB traces. C2986a–2–9/99 If PCB layout is used as heatsink, adding many vias around the power FET helps conduct more heat from the FET to the backplane of the PCB, thus reducing the maximum FET junction temperature. PCB Layout Issues OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 6-Lead Plastic Surface Mount Package RT-6 (SOT-23-6) 0.122 (3.10) 0.106 (2.70) 0.071 (1.80) 0.059 (1.50) 6 5 4 1 2 3 0.118 (3.00) 0.098 (2.50) PIN 1 0.037 (0.95) BSC 0.075 (1.90) BSC 0.051 (1.30) 0.035 (0.90) 0.057 (1.45) 0.035 (0.90) 0.020 (0.50) SEATING 0.010 (0.25) PLANE 0.006 (0.15) 0.000 (0.00) 108 0.009 (0.23) 08 0.003 (0.08) 0.022 (0.55) 0.014 (0.35) 8-Lead Narrow Body Package SO-8 0.1968 (5.00) 0.1890 (4.80) 0.1574 (4.00) 0.1497 (3.80) 8 5 1 4 0.2440 (6.20) 0.2284 (5.80) PIN 1 0.0196 (0.50) 3 458 0.0099 (0.25) 0.0500 (1.27) BSC SEATING PLANE 0.0688 (1.75) 0.0532 (1.35) 88 0.0500 (1.27) 0.0098 (0.25) 08 0.0160 (0.41) 0.0075 (0.19) 0.0192 (0.49) 0.0138 (0.35) PRINTED IN U.S.A. 0.0098 (0.25) 0.0040 (0.10) –8– REV. A