AD ADP2118ACPZ-2.5-R7

3 A, 1.2 MHz/600 kHz High Efficiency
Synchronous Step-Down DC-to-DC Converter
ADP2118
FEATURES
GENERAL DESCRIPTION
3 A continuous output current
75 mΩ and 40 mΩ integrated FET
±1.5% output accuracy
Input voltage range from 2.3 V to 5.5 V
Output voltage from 0.6 V to VIN
600 kHz or 1.2 MHz fixed switching frequency
Synchronizable between 600 kHz and 1.4 MHz
Selectable synchronize phase shift: 0o or 180o
Selectable PWM or PFM mode operation
Current mode architecture
Precision enable input
Power good output
Voltage tracking input
Integrated soft start
Internal compensation
Starts up into a precharged output
UVLO, OVP, OCP, and thermal shutdown
Available in 16-lead 4mm × 4mm LFCSP_WQ package
The ADP2118 is a low quiescent current, synchronous, step-down,
dc-to-dc converter in a compact 4mm × 4mm LFCSP_WQ
package. It uses a current mode, constant frequency pulse-width
modulation (PWM) control scheme for excellent stability and
transient response. Under light loads, the ADP2118 can be
configured to operate in pulse frequency modulation (PFM)
mode that reduces switching frequency to save power.
The ADP2118 runs from input voltages of 2.3 V to 5.5 V. The
output voltage of the ADP2118ACPZ-R7 is adjustable from
0.6 V to input voltage (VIN), and the ADP2118ACPZ-x.x-R7 are
available in preset output voltage options of 3.3 V, 2.5 V, 1.8 V,
1.5 V, 1.2 V, and 1.0 V. The ADP2118 requires minimal external
parts and provides a high efficiency solution with its integrated
power switch, synchronous rectifier, and internal compensation.
The IC draws less than 3 μA from the input source when it is
disabled. Other key features include undervoltage lockout
(UVLO), integrated soft start to limit inrush current at startup,
overvoltage protection (OVP), overcurrent protection (OCP),
and thermal shutdown (TSD).
APPLICATIONS
DSP/FPGA/ASIC core power
Telecommunication/networking equipment
PDAs and palmtop computers
Audio/video consumer electronics
C1
0.1µF
14
13
PVIN
CIN
100µF
X5R,
6.3V
1
SYNC/MODE
2
FREQ
3
TRK
SW 10
4
FB
SW 9
PVIN 12
GND
PGND
PGND
PGND
5
6
7
8
100
90
PFM OPERATION
80
70
L
1µH
SW 11
ADP2118
VIN
5V
COUT
100µF
X5R,
6.3V
VOUT
3.3V
3A
60
50
40
FPWM OPERATION
30
20
VIN = 5V
VOUT = 3.3V
fS = 1.2MHz
10
RTOP
10kΩ
08301-001
RBOT
2.21kΩ
0
0.01
0.1
1
OUTPUT CURRENT (A)
10
08301-050
15
EN
PGOOD
16
VIN
R2
10kΩ
EFFICIENCY (%)
R1
10Ω
Figure 1. Typical Applications Circuit
Figure 2. Efficiency vs. Output Current
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2009 Analog Devices, Inc. All rights reserved.
Rev. 0
ADP2118
TABLE OF CONTENTS
Features .............................................................................................. 1
Integrated Soft Start ................................................................... 14
Applications ....................................................................................... 1
Tracking ....................................................................................... 14
General Description ......................................................................... 1
Oscillator and Synchronization ................................................ 15
Revision History ............................................................................... 2
Current Limit and Short-Circuit Protection .......................... 15
Specifications..................................................................................... 3
Overvoltage Protection (OVP) ................................................. 15
Absolute Maximum Ratings ............................................................ 5
Undervoltage Lockout (UVLO) ............................................... 15
Thermal Resistance ...................................................................... 5
Thermal Shutdown .................................................................... 15
ESD Caution .................................................................................. 5
Power Good ................................................................................ 15
Pin Configuration and Function Descriptions ............................. 6
Applications Information .............................................................. 16
Typical Performance Characteristics ............................................. 7
Output Voltage Selection ........................................................... 16
Functional Block Diagram ............................................................ 13
Inductor Selection ...................................................................... 16
Theory of Operation ...................................................................... 14
Output Capacitor Selection....................................................... 16
Control Scheme .......................................................................... 14
Input Capacitor Selection .......................................................... 17
PWM Mode Operation .............................................................. 14
Voltage Tracking ......................................................................... 17
PFM Mode Operation................................................................ 14
Typical Application Circuits ......................................................... 18
Slope Compensation .................................................................. 14
Outline Dimensions ....................................................................... 21
Enable/Shutdown ....................................................................... 14
Ordering Guide .......................................................................... 21
REVISION HISTORY
7/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 24
ADP2118
SPECIFICATIONS
VIN = PVIN = 3.3 V, EN = VIN, SYNC/MODE = high @ TJ = −40°C to +125°C, unless otherwise noted. Typical values are at TJ = 25oC.
Table 1.
Parameter
VIN AND PVIN
VIN Voltage Range
PVIN Voltage Range
Quiescent Current
Shutdown Current
VIN Undervoltage Lockout Threshold
OUTPUT CHARACTERISTICS
Load Regulation1
Line Regulation1
FB
FB Regulation Voltage
FB Bias Current
SW
High-Side On Resistance2
Low-Side On Resistance2
SW Peak Current Limit
SW Maximum Duty Cycle
SW Minimum On Time3
TRK
TRK Input Voltage Range
TRK to FB Offset Voltage
TRK Input Bias Current
FREQUENCY
Oscillator Frequency
FREQ Input High Voltage
FREQ Input Low Voltage
SYNC/MODE
Synchronization Range
SYNC Minimum Pulse Width
SYNC Minimum Off Time
SYNC Input High Voltage
SYNC Input Low Voltage
INTEGRATED SOFT START
Soft Start Time
PGOOD
Power Good Range
Power Good Deglitch Time
PGOOD Leakage Current
PGOOD Output Low Voltage
Symbol
VIN
PVIN
IVIN
ISHDN
UVLO
Test Conditions/Comments
Min
2.3
2.3
No switching, SYNC/MODE = GND
Switching, no load, SYNC/MODE = high
VIN = PVIN = 5.5 V, EN = GND
VIN rising
VIN falling
2
Io = 0 A to 3 A
Io = 1.5 A
VFB
IFB
Typ
VIN = 2.3 V to 5.5 V
VIN = PVIN = 3.3 V, ISW = 500 mA
VIN = PVIN = 3.3 V, ISW = 500 mA
High-side switch, VIN = PVIN = 3.3 V
VIN = PVIN = 5.5 V, full frequency
VIN = PVIN = 5.5 V, full frequency
TRK = 0 mV to 500 mV
FREQ = VIN
FREQ = GND
100
680
0.3
2.2
2.1
Max
Unit
5.5
5.5
150
900
3
2.3
V
V
μA
μA
μA
V
V
0.08
0.05
0.591
4
%/A
%/V
0.6
0.01
0.609
0.1
V
μA
75
40
5.2
110
60
6.4
100
mΩ
mΩ
A
%
ns
600
+10
100
mV
mV
nA
1.4
700
MHz
kHz
V
V
100
0
−10
1.0
500
1.2
1.2
600
0.4
0.6
100
100
1.2
1.4
0.4
All switching frequency
FB rising threshold
FB rising hysteresis
FB falling threshold
FB falling hysteresis
From FB to PGOOD
VPGOOD = 5 V
IPGOOD = 1 mA
Rev. 0 | Page 3 of 24
2048
105
85
110
2.5
90
2.5
16
0.1
140
MHz
ns
ns
V
V
Clock cycles
115
94
1
200
%
%
%
%
Clock cycles
μA
mV
ADP2118
Parameter
EN
EN Input Rising Threshold
EN Input Hysteresis
EN Pull-Down Resistor
THERMAL
Thermal Shutdown Threshold
Thermal Shutdown Hysteresis
Symbol
Test Conditions/Comments
Min
Typ
Max
Unit
VIN = 2.3 V to 5.5 V
VIN = 2.3 V to 5.5 V
1.12
1.2
100
1
1.28
V
mV
MΩ
140
15
1
Specified by the circuit in Figure 45.
Pin-to-pin measurements.
3
Guaranteed by design.
2
Rev. 0 | Page 4 of 24
°C
°C
ADP2118
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 2.
Parameter
VIN, PVIN
SW
FB, SYNC/MODE, EN, TRK, FREQ, PGOOD
PGND to GND
Operating Junction Temperature Range
Storage Temperature Range
Soldering Conditions
Rating
−0.3 V to +6 V
−0.3 V to +6 V
−0.3 V to +6 V
−0.3 V to +0.3 V
−40°C to +125°C
−65°C to +150°C
JEDEC J-STD-020
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 3. Thermal Resistance
Package Type
16-Lead LFCSP_WQ
θJA
38.3
Unit
°C/W
Boundary Conditions
θJA is measured using natural convection on a JEDEC 4-layer
board, and the exposed pad is soldered to the printed circuit
board with thermal vias.
ESD CAUTION
Rev. 0 | Page 5 of 24
ADP2118
13 PVIN
14 VIN
16 PGOOD
15 EN
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
SYNC/MODE 1
12 PVIN
ADP2118
11 SW
TOP
VIEW
10 SW
TRK 3
9
SW
PGND 8
PGND 7
GND 5
PGND 6
FB 4
NOTES
1. THE EXPOSED PAD SHOULD BE SOLDERED TO
AN EXTERNAL GROUND PLANE UNDERNEATH
THE IC FOR THERMAL DISSIPATION.
08301-002
FREQ 2
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
Mnemonic
SYNC/MODE
2
3
FREQ
TRK
4
FB
5
6, 7, 8
9, 10, 11
12, 13
GND
PGND
SW
PVIN
14
VIN
15
EN
16
17 (EPAD)
PGOOD
Exposed Pad
Description
Synchronization Input (SYNC). Connect this pin to an external clock between 600 kHz and 1.4 MHz to
synchronize the switching frequency to the external clock (see the Oscillator and Synchronization section for
details).
CCM/PFM Selection (MODE). When this pin is connected to VIN, PFM mode is disabled and the ADP2118 only
works in continuous conduction mode (CCM). When this pin is connected to ground, PFM mode is enabled
and becomes active at light loads.
Frequency Selection. Connect to GND to select 600 kHz and VIN for 1.2 MHz.
Tracking Input. To track a master voltage, drive TRK from a voltage divider from the master voltage. If the
tracking function is not used, connect TRK to VIN.
Feedback Voltage Sense Input. Connect to a resistor divider from VOUT. For the fixed output version, connect
to VOUT directly.
Analog Ground. Connect to the ground plane.
Power Ground. Connect to the ground plane and to the output return side of the output capacitor.
Switch Node Output. Connect to the output inductor.
Power Input Pin. Connect this pin to the input power source. Connect a bypass capacitor between this pin
and PGND.
Bias Voltage Input Pin. Connect a bypass capacitor between this pin and GND and a small (10 Ω) resistor
between this pin and PVIN.
Precision Enable Pin. The external resistor divider can be used to set the turn-on threshold. To enable the part
automatically, connect the EN pin to VIN. This pin has a 1 MΩ pull-down resistor to GND.
Power-Good Output (Open Drain). Connect to a resistor to any pull-up voltage <5.5 V.
The exposed pad should be soldered to an external ground plane underneath the IC for thermal dissipation.
Rev. 0 | Page 6 of 24
ADP2118
TYPICAL PERFORMANCE CHARACTERISTICS
100
100
90
90
80
80
70
70
EFFICIENCY (%)
60
50
40
40
10
0
0.5
1.0
1.5
2.0
2.5
3.0
OUTPUT CURRENT (A)
0
90
90
80
80
70
70
EFFICIENCY (%)
100
60
50
40
INDUCTOR COILCRAFT
MSS1038-102NL
0.5
1.0
1.5
2.0
2.5
2.0
3.0
3.0
50
40
10
OUTPUT CURRENT (A)
2.5
60
VOUT = 1.0V
VOUT = 1.2V
VOUT = 1.5V
VOUT = 1.8V
VOUT = 2.5V
VOUT = 3.3V
20
0
0
1.5
30
VOUT = 1.0V
VOUT = 1.2V
VOUT = 1.5V
VOUT = 1.8V
VOUT = 2.5V
VOUT = 3.3V
INDUCTOR COILCRAFT
MSS1038-102NL
0
08301-015
10
1.0
Figure 7. Efficiency (1.2 MHz, VIN = 3.3 V, PFM) vs. Output Current
100
20
0.5
OUTPUT CURRENT (A)
Figure 4. Efficiency (1.2 MHz, VIN = 3.3 V, FPWM) vs. Output Current
30
INDUCTOR COILCRAFT
MSS1038-102NL
0
0
0.5
1.0
1.5
2.0
2.5
3.0
OUTPUT CURRENT (A)
08301-018
INDUCTOR COILCRAFT
MSS1038-102NL
0
08301-014
10
VOUT = 1.0V
VOUT = 1.2V
VOUT = 1.5V
VOUT = 1.8V
VOUT = 2.5V
20
08301-017
VOUT = 1.0V
VOUT = 1.2V
VOUT = 1.5V
VOUT = 1.8V
VOUT = 2.5V
20
EFFICIENCY (%)
50
30
30
Figure 8. Efficiency (1.2 MHz, VIN = 5 V, PFM) vs. Output Current
Figure 5. Efficiency (1.2 MHz, VIN = 5 V, FPWM) vs. Output Current
100
100
90
90
80
80
70
70
EFFICIENCY (%)
EFFICIENCY (%)
60
60
50
40
60
50
40
30
30
VOUT = 1.0V
VOUT = 1.2V
VOUT = 1.5V
VOUT = 1.8V
VOUT = 2.5V
10
INDUCTOR SUMIDA
CDRH105R2R2NC
10
0.5
1.0
1.5
2.0
2.5
INDUCTOR SUMIDA
CDRH105R2R2NC
0
0
0
VOUT = 1.0V
VOUT = 1.2V
VOUT = 1.5V
VOUT = 1.8V
VOUT = 2.5V
20
3.0
OUTPUT CURRENT (A)
08301-016
20
0
0.5
1.0
1.5
2.0
2.5
3.0
OUTPUT CURRENT (A)
Figure 6. Efficiency (600 kHz, VIN = 3.3 V, FPWM) vs. Output Current
Figure 9. Efficiency (600 kHz, VIN = 3.3 V, PFM) vs. Output Current
Rev. 0 | Page 7 of 24
08301-019
EFFICIENCY (%)
TA = 25°C, VIN = 5 V, VOUT = 1.2 V, L = 1 µH, CIN = 100 µF, COUT = 100 µF, unless otherwise noted.
100
100
90
90
80
80
70
70
EFFICIENCY (%)
60
50
40
60
50
40
30
30
VOUT = 1.0V
VOUT = 1.2V
VOUT = 1.5V
VOUT = 1.8V
VOUT = 2.5V
VOUT = 3.3V
10
INDUCTOR SUMIDA
CDRH105R2R2NC
0
0
0.5
1.0
1.5
2.0
2.5
VOUT = 1.0V
VOUT = 1.2V
VOUT = 1.5V
VOUT = 1.8V
VOUT = 2.5V
VOUT = 3.3V
20
10
3.0
OUTPUT CURRENT(A)
INDUCTOR SUMIDA
CDRH105R2R2NC
0
08301-020
20
0
0.5
1.0
1.5
2.0
2.5
3.0
OUTPUT CURRENT (A)
Figure 10. Efficiency (600 kHz, VIN = 5 V, FPWM) vs. Output Current
08301-023
EFFICIENCY (%)
ADP2118
Figure 13. Efficiency (600 kHz, VIN = 5 V, PFM) vs. Output Current
120
606
605
115
FEEDBACK VOLTAGE (mV)
105
100
95
90
2.7
3.1
3.5
3.9
4.3
4.7
5.1
602
601
600
599
598
597
595
5.5
VIN (V)
594
–40
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
Figure 11. Quiescent Current vs. VIN (No Switching)
08301-024
80
2.3
603
596
TJ = –40°C
TJ = +25°C
TJ = +125°C
85
08301-021
QUIESCENT CURRENT (µA)
604
110
Figure 14. Feedback Voltage vs. Temperature (VIN = 3.3 V)
130
80
120
70
NFET RESISTOR (mΩ)
100
90
80
70
60
50
40
30
60
40
2.3
2.7
3.1
TJ = –40°C
TJ = +25°C
TJ = +125°C
20
TJ = –40°C
TJ = +25°C
TJ = +125°C
3.5
3.9
4.3
4.7
5.1
5.5
VIN (V)
10
2.3
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
VIN (V)
Figure 15. NFET Resistor vs. VIN (Pin-to-Pin Measurements)
Figure 12. PFET Resistor vs. VIN (Pin-to-Pin Measurements)
Rev. 0 | Page 8 of 24
08301-025
50
08301-022
PFET RESISTOR (mΩ)
110
ADP2118
1350
660
640
1200
1150
1100
1050
1000
2.3
3.1
3.5
3.9
4.3
4.7
5.1
600
580
560
540
TJ = –40°C
TJ = +25°C
TJ = +125°C
520
TJ = –40°C
TJ = +25°C
TJ = +125°C
2.7
620
5.5
VIN (V)
500
2.3
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
VIN (V)
08301-029
SWITCHING FREQUENCY (kHz)
1250
08301-026
SWITCHING FREQUENCY (kHz)
1300
Figure 19. Switching Frequency vs. VIN at 600 kHz
Figure 16. Switching Frequency vs. VIN at 1.2 MHz
1.30
2.22
1.28
2.20
1.26
RISING
2.18
1.22
UVLO THRESHOLD (V)
ENABLE THRESHOLD (V)
1.24
RISING
1.20
1.18
1.16
1.14
1.12
FALLING
1.10
1.08
2.16
2.14
2.12
FALLING
2.10
1.06
1.04
2.08
0
20
40
60
80
100
120
TEMPERATURE (°C)
2.06
–40
5.4
5.3
5.3
PEAK CURRENT LIMIT (A)
5.4
5.2
5.1
5.0
4.9
80
100
120
4.9
4.7
60
80
5.0
4.7
40
60
5.1
4.8
20
40
5.2
4.8
100
120
TEMPERATURE (°C)
4.6
2.3
08301-028
PEAK CURRENT LIMIT (A)
5.5
0
20
Figure 20. UVLO Threshold vs. Temperature (VIN = 3.3 V)
5.5
–20
0
TEMPERATURE (°C)
Figure 17. EN Threshold vs. Temperature
4.6
–40
–20
2.7
3.1
3.5
3.9
4.3
4.7
5.1
VIN (V)
Figure 18. Peak Current Limit vs. Temperature (VIN = 3.3 V)
Figure 21. Peak Current Limit vs. VIN (TJ = 25°C)
Rev. 0 | Page 9 of 24
5.5
08301-031
–20
08301-027
1.00
–40
08301-030
1.02
ADP2118
EN
EN
3
3
VOUT
VOUT
1
1
PGOOD
PGOOD
2
2
IL
IL
CH1 500mV
CH3 5V
CH2 5V
CH4 2A Ω
M1ms
T 20.40%
A CH3
08301-035
4
08301-032
4
CH1 500mV CH2 5V
CH4 2A Ω
CH3 5V
3.10V
Figure 22. Soft Start with Full Load (1.2 MHz, VIN = 5 V)
M1ms
T
30.2%
A CH3
3.10V
Figure 25. Soft Start with Precharge (1.2 MHz, VIN = 5 V)
VOUT (AC)
VOUT (AC)
1
1
IO
IO
CH1 50mV
CH4 2A Ω
M200µs
T 30.40%
A CH4
1.36A
08301-036
4
08301-033
4
CH1 50mV
CH4 2A Ω
M200µs
T
30.40%
A CH4
1.36A
Figure 26. Load Transient (1.2 MHz, FPWM, VIN = 5 V)
Figure 23. Load Transient (1.2 MHz, PFM, VIN = 5 V)
SYNC
SYNC
2
2
SW
SW
3
08301-034
08301-037
3
CH2 2V
CH3 2V
M 400ns
T
–8ns
A CH2
CH2 2V
2.88V
CH3 2V
M400ns
T
–8ns
A CH2
2.88V
Figure 27. Synchronized to 1 MHz 180° Out of Phase
Figure 24. Synchronized to 1 MHz In Phase
Rev. 0 | Page 10 of 24
ADP2118
VOUT
VOUT
1
1
SW
SW
2
2
IL
IL
CH1 500mV
CH2 5V
CH4 5A Ω
M2ms
T 29.60%
A CH1
08301-041
4
08301-038
4
CH1 500mV CH2 5V
CH4 5A Ω
670mV
Figure 28. Output Short
M2ms
T 59.60%
A CH1
670mV
Figure 31. Output Short Recovery
1
VOUT (AC)
TRK
IL
4
FB
1
SW
CH1 500mV
CH2 500mV
M4ms
T 59%
A CH2
08301-042
08301-039
2
CH1 50mV
640mV
CH2 5V
CH4 1A Ω
M4µs
T
64.60%
A CH4
1.72A
A CH2
3.1V
Figure 32. PFM Mode
Figure 29. Tracking Function
VOUT (AC)
VOUT (AC)
1
1
IL
IL
4
4
SW
SW
CH1 10mV
CH2 5V
CH4 1A Ω
M 400ns
T 57.80%
A CH2
3.90V
08301-043
2
08301-040
2
CH1 10mV
CH2 5V
CH4 2A Ω
M400ns
T 57.8%
Figure 33. Continuous Conduction Mode (CCM)
Figure 30. Discontinuous Conduction Mode (DCM)
Rev. 0 | Page 11 of 24
ADP2118
48
160
120
36
120
24
80
24
80
12
40
12
40
0
0
0
0
CROSS FREQUENCY: 102kHz
PHASE MARGIN: 50°
1k
10k
100k
–24
–80
–120
–36
–120
–160
–48
–200
–60
100
1M
FREQUENCY (Hz)
1
2
–160
CROSS FREQUENCY: 93kHz
PHASE MARGIN: 56°
–200
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 37. Bode Plot at VIN = 5 V, VOUT = 1.2 V, IO = 3 A, fS = 1.2 MHz
1
2
60
48
160
48
160
36
120
36
120
24
80
24
80
12
40
12
40
0
0
0
0
–24
–80
–120
–36
–120
–160
–48
–200
–60
100
–36
–60
100
1k
10k
100k
PHASE (Degrees)
–80
–24
08301-045
–40
–40
CROSS FREQUENCY: 81kHz
PHASE MARGIN: 63°
1M
FREQUENCY (Hz)
1
2
–160
CROSS FREQUENCY: 69kHz
PHASE MARGIN: 69°
–200
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 35. Bode Plot at VIN = 5 V, VOUT = 1.5 V, IO = 3 A, fS = 1.2 MHz
60
200
–12
–12
–48
MAGNITUDE (dB)
200
60
Figure 38. Bode Plot at VIN = 5 V, VOUT = 1.8 V, IO = 3 A, fS = 1.2 MHz
1
2
60
48
160
48
160
36
120
36
120
24
80
24
80
12
40
12
40
0
0
0
0
PHASE (Degrees)
–80
–24
–80
–120
–36
–120
–160
–48
–160
–36
–48
–200
1M
FREQUENCY (Hz)
08301-046
–40
–24
100k
200
–12
–40
CROSS FREQUENCY: 52kHz
PHASE MARGIN: 76°
–60
100
1k
10k
MAGNITUDE (dB)
200
–12
08301-047
–48
–80
PHASE (Degrees)
–36
–40
08301-048
–24
–12
CROSS FREQUENCY: 46kHz
PHASE MARGIN: 79°
–60
100
1k
10k
Figure 36. Bode Plot at VIN = 5 V, VOUT = 2.5 V, IO = 3 A, fS = 1.2 MHz
–200
100k
1M
FREQUENCY (Hz)
Figure 39. Bode Plot at VIN = 5 V, VOUT = 3.3 V, IO = 3 A, fS = 1.2 MHz
Rev. 0 | Page 12 of 24
PHASE (Degrees)
–40
PHASE (Degrees)
–12
MAGNITUDE (dB)
160
36
PHASE (Degrees)
200
48
Figure 34. Bode Plot at VIN = 5 V, VOUT = 1.0 V, IO = 3 A, fS = 1.2 MHz
MAGNITUDE (dB)
2
60
–60
100
MAGNITUDE (dB)
1
200
08301-044
MAGNITUDE (dB)
2
08301-049
1
60
ADP2118
FUNCTIONAL BLOCK DIAGRAM
PVIN
EN
VIN
ADP2118
PMOS CURRENT
SENSE AMP
ZCOMP
TRK
ERRO AMP
0.6V
SOFT
START
UVLO
Gm
PFET
SKIP
CMP
LOGIC
CONTROL
SW
SKIP MODE
THRESHOLD
FB
NFET
0.66V
SLOPE
COMPENSATION
CLK
NMOS
CURRENT
SENSE AMP
0.54V
PGOOD
OSCILLATOR
SYNC/MODE
FREQ
Figure 40. Functional Block Diagram
Rev. 0 | Page 13 of 24
PGND
08301-003
ZERO
CURRENT
CMP
GND
ADP2118
THEORY OF OPERATION
The ADP2118 is a step-down, dc-to-dc converter that uses fixed
frequency, peak current-mode architecture with an integrated
high-side switch and low-side synchronous rectifier. The high
switching frequency and tiny 16-lead, 4 mm × 4 mm LFCSP_WQ
package allow for a small step-down dc-to-dc converter solution. The integrated high-side switch (P-channel MOSFET) and
synchronous rectifier (N-channel MOSFET) yield high efficiency
at medium-to-full loads, and light load efficiency is improved
by PFM mode.
The ADP2118 operates with an input voltage from 2.3 V to
5.5 V and regulates the output voltage down to 0.6 V. The
ADP2118 is also available with preset output voltage options
of 3.3 V, 2.5 V, 1.8 V, 1.5 V, 1.2 V, and 1.0 V.
CONTROL SCHEME
The ADP2118 uses the fixed frequency, peak current mode
PWM control architecture and operates in PWM mode for
medium-to-full loads but shifts to PFM mode (if enabled) at
light loads to maintain high efficiency. When operating in fixed
frequency PWM mode, the duty cycle of the integrated switches
is adjusted to regulate the output voltage. When operating in
PFM mode at light loads, the switching frequency is adjusted to
regulate the output voltage.
The ADP2118 operates in PWM mode when the load current is
greater than the pulse-skipping threshold current. At load
currents below this value, the converter smoothly transitions to
the PFM mode of operation.
output capacitor supplies all the load current. Because the output
voltage dips and recovers occasionally, the output voltage ripple
in this mode is larger than the ripple in the PWM mode of
operation.
SLOPE COMPENSATION
Slope compensation stabilizes the internal current control loop
of the ADP2118 when operating close to and beyond 50% duty
cycle to prevent subharmonic oscillations. It is implemented by
summing an artificial voltage ramp to the current sense signal
during the on-time of the P-channel MOSFET switch. This
voltage ramp depends on the output voltage. When operating at
high output voltages, there is more slope compensation. The
slope compensation ramp value determines the minimum
inductor that can be used to prevent subharmonic oscillations.
ENABLE/SHUTDOWN
The EN pin is a precision analog input that enables the device
when the voltage exceeds 1.2 V (typical) and has 100 mV
hysteresis. When the enable voltage falls below 1.1 V (typical)
the part turns off. To force the ADP2118 to automatically start
when input power is applied, connect EN to VIN.
When the ADP2118 is shut down, the soft start capacitor is
discharged. This causes a new soft start cycle to begin when the
part is reenabled.
An internal pull-down resistor (1 MΩ) prevents an accidental
enable if EN is left floating.
PWM MODE OPERATION
INTEGRATED SOFT START
In PWM mode, the ADP2118 operates at a fixed frequency set
by the FREQ pin. At the start of each oscillator cycle, the Pchannel MOSFET switch is turned on, putting a positive voltage
across the inductor. Current in the inductor increases until the
current sense signal crosses the peak inductor current level, turns
off the P-channel MOSFET switch, and turns on the N-channel
MOSFET synchronous rectifier. This puts a negative voltage
across the inductor, causing the inductor current to decrease.
The synchronous rectifier stays on for the rest of the cycle or
until the inductor current reaches zero, which causes the zerocrossing comparator to turn off the N-channel MOSFET as well.
The ADP2118 has integrated soft start circuitry to limit the
output voltage rise time and reduce inrush current at startup.
The soft start time is fixed at 2048 clock cycles.
The peak inductor current level is set by VCOMP. The VCOMP is the
output of a transconductance error amplifier that compares the
feedback voltage with an internal 0.6 V reference.
PFM MODE OPERATION
When PFM mode is enabled, the ADP2118 smoothly transitions to the variable frequency PFM mode of operation when
the load current decreases below the pulse-skipping threshold
current, switching only as necessary to maintain the output
voltage within regulation. When the output voltage drops below
regulation, the ADP2118 enters PWM mode for a few oscillator
cycles to increase the output voltage back to regulation. During the
wait time between bursts, both power switches are off, and the
If the output voltage is precharged prior to turn-on, the
ADP2118 prevents a reverse inductor current (that would
discharge the output capacity) until the soft start voltage
exceeds the voltage on the FB pin.
TRACKING
The ADP2118 has a tracking input, TRK, that allows the output
voltage to track another voltage (master voltage). It is especially
useful in core and I/O voltage tracking for FPGAs, DSPs, and
ASICs.
The internal error amplifier includes three positive inputs: the
internal reference voltage, the soft start voltage, and the TRK
voltage. The error amplifier regulates the FB voltage to the
lowest of the three voltages. To track a master voltage, tie the
TRK pin to a resistor divider from the master voltage.
If the TRK function is not used, connect the TRK pin to VIN.
Rev. 0 | Page 14 of 24
ADP2118
OSCILLATOR AND SYNCHRONIZATION
The internal oscillator of ADP2118 can be set to 600 kHz or
1.2 MHz. Drive the FREQ pin low for 600 kHz; drive FREQ
pin high for 1.2 MHz.
To synchronize the ADP2118, drive an external clock at the
SYNC/MODE pin. The frequency of the external clock can be
in the range of 600 kHz to 1.4 MHz. During synchronization,
the converter operates in CCM mode only.
If the FREQ pin is low, the switching frequency is in phase with
the external clock; if the FREQ pin is high, the switching
frequency is 180o out of phase with the external clock.
CURRENT LIMIT AND SHORT-CIRCUIT
PROTECTION
and the low-side MOSFET turns on until the current through it
reaches the limit (−0.9 A for forced continuous mode and 0 A
for PFM mode). Thereafter, both the MOSFETs are held in the
off state until FB falls below 0.54 V (typical), and then the part
restarts. The behavior of PGOOD under this condition is
described in the Power Good section.
UNDERVOLTAGE LOCKOUT (UVLO)
Undervoltage lockout circuitry is integrated on the ADP2118. If
the input voltage drops below 2.1 V, the ADP2118 shuts down,
and both the power switch and the synchronous rectifier turn
off. When the voltage rises again above 2.2 V, the soft start period
is initiated, and the part is enabled.
THERMAL SHUTDOWN
The ADP2118 has a peak current limit protection circuit to
prevent current runaway. The peak current is limited at 5.2 A.
When the inductor peak current reaches the current limit value,
the high-side MOSFET turns off and the low-side MOSFET
turns on until the next cycle while the overcurrent counter
increments. If the overcurrent counter count exceeds 10, the
part enters hiccup mode. The high-side FET and low-side FET
are both turned off. The part remains in this mode for 4096
clock cycles and then attempts to restart from soft start. If the
current limit fault has cleared, the part resumes normal
operation. Otherwise, it reenters hiccup mode again after
counting 10 current-limit violations.
OVERVOLTAGE PROTECTION (OVP)
The output voltage is continuously monitored by a comparator
through the FB pin, which is at 0.6 V (typical) under normal
operation. This comparator is set to activate when the FB
voltage exceeds 0.66 V (typical), thus indicating an output
overvoltage condition. If the voltage remains above this
threshold for 16 clock cycles, the high-side MOSFET turns off
In the event that the ADP2118 junction temperature rises above
140°C, the thermal shutdown circuit turns off the converter.
Extreme junction temperatures can be the result of high current
operation, poor circuit board design, and/or high ambient
temperature. A 15°C hysteresis is included so that when thermal
shutdown occurs, the ADP2118 does not return to operation
until the on-chip temperature drops below 125°C. When
coming out of thermal shutdown, soft start is initiated.
POWER GOOD
PGOOD is an active high, open-drain output and requires a
resistor to pull it up to a voltage. A high indicates that the
voltage on the FB pin (and therefore the output voltage) is
within 10% of the desired value. A low on this pin indicates that
the voltage on the FB pin is not within 10% of the desired value.
There is a 16 cycle waiting period after FB is detected as being
out of bounds. If FB returns to within the ±10% range, it is
ignored by PGOOD circuitry.
Rev. 0 | Page 15 of 24
ADP2118
APPLICATIONS INFORMATION
This section describes the external components selection for the
ADP2118. The typical application circuit is shown in Figure 41.
C1
0.1µF
R1
10Ω
SYNC/MODE
2
FREQ
14
13
PVIN
CIN
100µF
X5R,
6.3V
PVIN 12
SW
ADP2118
PGND
PGND
SW 9
PGND
SW 10
FB
GND
TRK
4
5
6
7
8
The peak inductor current should be kept below the peak
current limit threshold value and can be calculated as
L
1µH
11
3
The negative current limit (−0.9 A) also limits the minimum
inductor value. The inductor current ripple (ΔIL) calculated by
the selected inductor should not exceed 1.8 A.
VIN
5V
COUT
100µF
X5R,
6.3V
I PEAK = I O +
VOUT
1.2V
3A
OUTPUT CAPACITOR SELECTION
RTOP
10kΩ
Figure 41. Application Circuit
OUTPUT VOLTAGE SELECTION
The output voltage of the adjustable version of the ADP2118
can be set by an external resistive voltage divider by using the
following equation to set the voltage:
 R
VOUT = 0.6 × 1 + TOP
 R BOT




The inductor value is determined by the operating frequency,
input voltage, output voltage, and ripple current. Using a small
inductor leads to larger inductor current ripple and provides
fast transient response but degrades efficiency, whereas a large
inductor value leads to small current ripple and good efficiency
but slow transient response. As a guideline, the inductor current
ripple, ΔIL, is typically set to 1/3 of the maximum load current
trade-off between the transient response and efficiency. The
inductor can be calculated using the following equation:
∆I L × f S
The output ripple is determined by the ESR and the
capacitance.

1
∆VOUT = ∆I L ×  ESR +
8 × C OUT × f S

The load transient response depends on the inductor, output
capacitor, and the control loop.
VIN (V)
3.3
3.3
3.3
3.3
3.3
5
5
5
5
5
5
where:
VIN is the input voltage.
VOUT is the output voltage.
ΔIL is the inductor current ripple.
D is the duty cyle.
D=




Table 5. Recommended L and COUT Value at fS = 1.2 MHz
INDUCTOR SELECTION
(VIN − VOUT ) × D
The output voltage ripple, load step transient, and loop stability
determine the output capacitor selection.
The ADP2118 has integrated loop compensation for simple
power design. Table 5 and Table 6 show the typical recommended inductors and capacitors for the ADP2118. X5R or X7R
ceramic capacitors are highly recommended.
To limit output voltage accuracy degradation due to FB bias
current (0.1 µA maximum) to less than 0.5% (maximum),
ensure that RBOT is less than 30 kΩ.
L=
∆I L
2
Ensure that the rms current of the selected inductor is greater
than the maximum load current and that its saturation current
is greater than the peak current limit of the converter.
08301-004
RBOT
10kΩ
1
15
EN
PGOOD
16
VIN
R2
10kΩ
The ADP2118 uses slope compensation in the current loop to
prevent subharmonic oscillations when the duty cycle is larger
than 50%. The internal slope compensation limits the minimum
inductor value.
VOUT
V IN
Rev. 0 | Page 16 of 24
VOUT (V)
1.0
1.2
1.5
1.8
2.5
1.0
1.2
1.5
1.8
2.5
3.3
L (µH)
1
1
1
1
1
1
1
1
1
1
1
COUT (µF)
100 + 47
100
100
100
100
100 + 47
100
100
100
100
100
ADP2118
A common application is coincident tracking, shown in Figure 43.
Coincident tracking limits the slave output voltage to be the
same as the master voltage until it reaches regulation. Connect
the TRK pin to a resistor divider from the master voltage. For
coincident tracking, set RTRKT = RTOP and RTRKB = RBOT.
Table 6. Recommended L and COUT Value at fS = 600 kHz
COUT (μF)
100 + 47
100
100
100
100
100 + 47
100
100
100
100
100
Ratiometric tracking is shown in Figure 44. The slave output is
limited to a fraction of the master voltage. In this application,
the slave and master voltages reach the final value at the same
time. The ratio of the slave output voltage to the master voltage
is a function of the two dividers.
VSLAVE

V MASTER
Higher or lower inductors and output capacitors can be used in
the converter, but the system stability and load transient
performance need to be checked.
The minimum output capacitor can be 47 μF. If fS = 1.2 MHz,
the inductor range is 0.8 μH to 3.3 μH. If fS = 600 kHz, the
inductor range is 1.5 μH to 3.3 μH.
RTRKB
VMASTER
VSLAVE
ADP2118
RTRKT
TRK
RTOP
FB
Part Number
MSS1038, MSS1048, MSS1260
CDRH103R, CDRH104R, CDRH105R
RBOT
Figure 42. Voltage Tracking
Part Number
GRM32ER60J107ME20
GRM32ER60J476ME20
C3225X5R0J107M
C3225X5R0J476M
Description
100 μF, 6.3 V, X5R, 1210
47 μF, 6.3 V, X5R, 1210
100 μF, 6.3 V, X5R, 1210
47 μF, 6.3 V, X5R, 1210
VMASTER
VOLTAGE
Table 8. Recommended Capacitors
Manufacturer
Murata
Murata
TDK
TDK
1
RTOP
R BOT
RTRKT
RTRKB
Table 7. Recommended Inductors
Manufacturer
Coilcraft
Sumida
1
08301-005
L (μH)
1.5
1.5
1.5
1.5
1.5
1.5
1.5
2.2
2.2
2.2
2.2
INPUT CAPACITOR SELECTION
VSLAVE
08301-006
VOUT (V)
1.0
1.2
1.5
1.8
2.5
1.0
1.2
1.5
1.8
2.5
3.3
TIME
I RMS  I O  D  1  D 
VMASTER
VOLTAGE
The input capacitor reduces the input voltage ripple caused by
the switch current on PVIN. Place the input capacitor as close
as possible to the PVIN pin. A 22 μF or 47 μF ceramic capacitor
is recommended. The rms current rating of the input capacitor
should be larger than the following equation:
Figure 43. Coincident Tracking
VSLAVE
TIME
VOLTAGE TRACKING
Figure 44. Ratiometric Tracking
The ADP2118 includes a tracking feature that allows the
ADP2118 output (slave voltage) to be configured to track an
external voltage (master voltage), as shown in Figure 42.
Rev. 0 | Page 17 of 24
08301-007
VIN (V)
3.3
3.3
3.3
3.3
3.3
5
5
5
5
5
5
ADP2118
TYPICAL APPLICATION CIRCUITS
C1
0.1µF
R1
10Ω
13
VIN
EN
14
PVIN
15
CIN
100µF
X5R,
6.3V
1
SYNC/MODE
PVIN 12
2
FREQ
3
TRK
SW 10
4
FB
SW 9
L
1µH
SW 11
GND
PGND
PGND
PGND
ADP2118
5
6
7
8
VIN
3.3V
COUT
100µF
X5R,
6.3V
VOUT
1.2V
3A
L: MSS1038-102NL COILCRAFT
CIN, COUT: C3225X5R0J107M TDK
RTOP
10kΩ
08301-008
RBOT
10kΩ
16
PGOOD
R2
10kΩ
Figure 45. 1.2 V, 3 A, 1.2 MHz Step-Down Regulator,
Force Continuous Conduction Mode
C1
0.1µF
16
15
14
13
PGOOD
EN
VIN
PVIN
R2
10kΩ
CIN
100µF
X5R,
6.3V
1
SYNC/MODE
2
FREQ
3
TRK
SW 10
4
FB
SW 9
RBOT RTOP
15kΩ 47.5kΩ
PVIN 12
SW 11
GND
PGND
PGND
PGND
ADP2118
5
6
7
8
VIN
5V
L
1µH
COUT
47µF
X5R,
10V
VOUT
2.5V
3A
L: MSS1038-102NL COILCRAFT
CIN: C3225X5R0J107M TDK
COUT: GRM32ER61A476KE20 MURATA
Figure 46. 2.5 V, 3 A, 1.2 MHz Step-Down Regulator, Enable PFM Mode
Rev. 0 | Page 18 of 24
08301-009
R1
10Ω
ADP2118
C1
0.1µF
R1
10Ω
1
SYNC/MODE
2
FREQ
14
13
VIN
PVIN
CIN
100µF
X5R,
6.3V
PVIN 12
L
1µH
SW 11
ADP2118
PGND
SW 9
PGND
SW 10
FB
PGND
TRK
4
GND
3
5
6
7
8
VIN
5V
VOUT
1.8V
3A
COUT
100µF
X5R,
6.3V
L: MSS1038-102NL COILCRAFT
CIN, COUT: C3225X5R0J107M TDK
RTOP
20kΩ
08301-010
RBOT
10kΩ
15
EN
1MHz
EXT
CLOCK
16
PGOOD
R2
10kΩ
Figure 47. 1.8 V, 3 A Step-Down Regulator,
Synchronized to 1 MHz In Phase with the External Clock
C1
0.1µF
RBOT
10kΩ
1
SYNC/MODE
2
FREQ
14
13
VIN
PVIN
15
EN
1MHz
EXT
CLOCK
16
PGOOD
R2
10kΩ
CIN
100µF
X5R,
6.3V
PVIN 12
SW 11
ADP2118
FB
SW 9
RTOP
15kΩ
PGND
4
PGND
SW 10
PGND
TRK
GND
3
5
6
7
8
VIN
5V
L
1µH
COUT
100µF
X5R,
6.3V
VOUT
1.5V
3A
L: MSS1038-102NL COILCRAFT
CIN, COUT: C3225X5R0J107M TDK
Figure 48. 1.5 V, 3 A Step-Down Regulator, Synchronized to 1 MHz,
180° Out of Phase with the External Clock
Rev. 0 | Page 19 of 24
08301-011
R1
10Ω
ADP2118
C1
0.1µF
RTRKT
10kΩ
1
SYNC/MODE
2
FREQ
15
14
13
EN
PVIN
PGOOD
16
VIN
R2
10kΩ
CIN
100µF
X5R,
6.3V
PVIN 12
SW 11
ADP2118
3
TRK
SW 10
4
FB
SW 9
RBOT
2.21kΩ
RTOP
10kΩ
PGND
PGND
PGND
RTRKB
2.21kΩ
GND
VMASTER
5
6
7
8
VIN
5V
L
1µH
COUT
100µF
X5R,
6.3V
L: MSS1038-102NL COILCRAFT
CIN, COUT: C3225X5R0J107M TDK
Figure 49. 3.3 V, 3 A, 1.2 MHz Step-Down Regulator, Tracking Mode
Rev. 0 | Page 20 of 24
VOUT
3.3V
3A
08301-012
R1
10Ω
ADP2118
OUTLINE DIMENSIONS
0.35
0.30
0.25
0.65
BSC
PIN 1
INDICATOR
16
13
1
12
EXPOSED
PAD
2.60
2.50 SQ
2.40
9
TOP VIEW
0.80
0.75
0.70
0.50
0.40
0.30
4
8
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
5
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WGGC.
042709-A
PIN 1
INDICATOR
4.10
4.00 SQ
3.90
Figure 50. 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ]
4 mm × 4 mm Body, Very Very Thin Quad
(CP-16-26)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADP2118ACPZ-R71
ADP2118ACPZ-1.0-R71
ADP2118ACPZ-1.2-R71
ADP2118ACPZ-1.5-R71
ADP2118ACPZ-1.8-R71
ADP2118ACPZ-2.5-R71
ADP2118ACPZ-3.3-R71
1
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Output Voltage
Adjustable
1.0 V
1.2 V
1.5 V
1.8 V
2.5 V
3.3 V
Z = RoHS Compliant Part.
Rev. 0 | Page 21 of 24
Package Description
16-Lead LFCSP_WQ
16-Lead LFCSP_WQ
16-Lead LFCSP_WQ
16-Lead LFCSP_WQ
16-Lead LFCSP_WQ
16-Lead LFCSP_WQ
16-Lead LFCSP_WQ
Package Option
CP-16-26
CP-16-26
CP-16-26
CP-16-26
CP-16-26
CP-16-26
CP-16-26
ADP2118
NOTES
Rev. 0 | Page 22 of 24
ADP2118
NOTES
Rev. 0 | Page 23 of 24
ADP2118
NOTES
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08301-0-7/09(0)
Rev. 0 | Page 24 of 24